AMX Switch NI-3101-SIG User manual

Brand: AMX

Model: Switch NI-3101-SIG

Type: User manual

This manual is also suitable for

NI-3101-SIG

Operation/Reference Guide

Central Controllers

NI-3101-SIG

Signature Series NetLinx

Integrated Controller

Last Revised: 9/13/2011

NI-3101-SIG Operation/Reference Guide

AMX Limited Warranty and Disclaimer

This Limited Warranty and Disclaimer extends only to products purchased directly from AMX or an AMX Authorized Partner which

include AMX Dealers, Distributors, VIP’s or other AMX authorized entity.

AMX warrants its products to be free of defects in material and workmanship under normal use for three (3) years from the date of

purchase, with the following exceptions:

• Electroluminescent and LCD Control Panels are warranted for three (3) years, except for the display and touch overlay compo-

nents are warranted for a period of one (1) year.

• Disk drive mechanisms, pan/tilt heads, power supplies, and MX Series products are warranted for a period of one (1) year.

• AMX lighting products are guaranteed to switch on and off any load that is properly connected to our lighting products, as long

as the AMX lighting products are under warranty. AMX also guarantees the control of dimmable loads that are properly con-

nected to our lighting products. The dimming performance or quality there of is not guaranteed, impart due to the random combi-

nations of dimmers, lamps and ballasts or transformers.

• AMX software is warranted for a period of ninety (90) days.

• Batteries and incandescent lamps are not covered under the warranty.

• AMX AutoPatch Epica, Modula, Modula Series4, Modula CatPro Series and 8Y-3000 product models will be free of defects in

materials and manufacture at the time of sale and will remain in good working order for a period of three (3) years following the

date of the original sales invoice from AMX. The three-year warranty period will be extended to the life of the product (Limited

Lifetime Warranty) if the warranty card is filled out by the dealer and/or end user and returned to AMX so that AMX receives it

within thirty (30) days of the installation of equipment but no later than six (6) months from original AMX sales invoice date. The

life of the product extends until five (5) years after AMX ceases manufacturing the product model. The Limited Lifetime Warranty

applies to products in their original installation only. If a product is moved to a different installation, the Limited Lifetime Warranty

will no longer apply, and the product warranty will instead be the three (3) year Limited Warranty.

All products returned to AMX require a Return Material Authorization (RMA) number. The RMA number is obtained from the AMX

RMA Department. The RMA number must be clearly marked on the outside of each box. The RMA is valid for a 30-day period. After

the 30-day period the RMA will be cancelled. Any shipments received not consistent with the RMA, or after the RMA is cancelled, will

be refused. AMX is not responsible for products returned without a valid RMA number.

AMX is not liable for any damages caused by its products or for the failure of its products to perform. This includes any lost profits, lost

savings, incidental damages, or consequential damages. AMX is not liable for any claim made by a third party or by an AMX Autho-

rized Partner for a third party.

This Limited Warranty does not apply to (a) any AMX product that has been modified, altered or repaired by an unauthorized agent or

improperly transported, stored, installed, used, or maintained; (b) damage caused by acts of nature, including flood, erosion, or earth-

quake; (c) damage caused by a sustained low or high voltage situation or by a low or high voltage disturbance, including brownouts,

sags, spikes, or power outages; or (d) damage caused by war, vandalism, theft, depletion, or obsolescence.

This limitation of liability applies whether damages are sought, or a claim is made, under this warranty or as a tort claim (including

negligence and strict product liability), a contract claim, or any other claim. This limitation of liability cannot be waived or amended by

any person. This limitation of liability will be effective even if AMX or an authorized representative of AMX has been advised of the

possibility of any such damages. This limitation of liability, however, will not apply to claims for personal injury.

Some states do not allow a limitation of how long an implied warranty last. Some states do not allow the limitation or exclusion of inci-

dental or consequential damages for consumer products. In such states, the limitation or exclusion of the Limited Warranty may not

apply. This Limited Warranty gives the owner specific legal rights. The owner may also have other rights that vary from state to state.

The owner is advised to consult applicable state laws for full determination of rights.

EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY, AMX MAKES NO OTHER WARRANTIES, EXPRESSED OR

IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. AMX

EXPRESSLY DISCLAIMS ALL WARRANTIES NOT STATED IN THIS LIMITED WARRANTY. ANY IMPLIED WARRANTIES THAT

MAY BE IMPOSED BY LAW ARE LIMITED TO THE TERMS OF THIS LIMITED WARRANTY. EXCEPT AS OTHERWISE LIMITED

BY APPLICABLE LAW, AMX RESERVES THE RIGHT TO MODIFY OR DISCONTINUE DESIGNS, SPECIFICATIONS, WARRAN-

TIES, PRICES, AND POLICIES WITHOUT NOTICE.

AMX Software License and Warranty Agreement

• LICENSE GRANT. AMX grants to Licensee the non-exclusive right to use the AMX Software in the manner described in this

License. The AMX Software is licensed, not sold. This license does not grant Licensee the right to create derivative works of the

AMX Software. The AMX Software consists of generally available programming and development software, product documenta-

tion, sample applications, tools and utilities, and miscellaneous technical information. Please refer to the README.TXT file on

the compact disc or download for further information regarding the components of the AMX Software. The AMX Software is sub-

ject to restrictions on distribution described in this License Agreement. AMX Dealer, Distributor, VIP or other AMX authorized

entity shall not, and shall not permit any other person to, disclose, display, loan, publish, transfer (whether by sale, assignment,

exchange, gift, operation of law or otherwise), license, sublicense, copy, or otherwise disseminate the AMX Software. Licensee

may not reverse engineer, decompile, or disassemble the AMX Software.

• ACKNOWLEDGEMENT. You hereby acknowledge that you are an authorized AMX dealer, distributor, VIP or other AMX autho-

rized entity in good standing and have the right to enter into and be bound by the terms of this Agreement.

• INTELLECTUAL PROPERTY. The AMX Software is owned by AMX and is protected by United States copyright laws, patent

laws, international treaty provisions, and/or state of Texas trade secret laws. Licensee may make copies of the AMX Software

solely for backup or archival purposes. Licensee may not copy the written materials accompanying the AMX Software.

• TERMINATION. AMX RESERVES THE RIGHT, IN ITS SOLE DISCRETION, TO TERMINATE THIS LICENSE FOR ANY REA-

SON UPON WRITTEN NOTICE TO LICENSEE. In the event that AMX terminates this License, the Licensee shall return or

destroy all originals and copies of the AMX Software to AMX and certify in writing that all originals and copies have been

returned or destroyed.

• PRE-RELEASE CODE. Portions of the AMX Software may, from time to time, as identified in the AMX Software, include PRE-

RELEASE CODE and such code may not be at the level of performance, compatibility and functionality of the GA code. The

PRE-RELEASE CODE may not operate correctly and may be substantially modified prior to final release or certain features may

not be generally released. AMX is not obligated to make or support any PRE-RELEASE CODE. ALL PRE-RELEASE CODE IS

PROVIDED "AS IS" WITH NO WARRANTIES.

• LIMITED WARRANTY. AMX warrants that the AMX Software (other than pre-release code) will perform substantially in accor-

dance with the accompanying written materials for a period of ninety (90) days from the date of receipt. AMX DISCLAIMS ALL

OTHER WARRANTIES, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO IMPLIED WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, WITH REGARD TO THE AMX SOFTWARE. THIS LIM-

ITED WARRANTY GIVES LICENSEE SPECIFIC LEGAL RIGHTS. Any supplements or updates to the AMX SOFTWARE,

including without limitation, any (if any) service packs or hot fixes provided to Licensee after the expiration of the ninety (90) day

Limited Warranty period are not covered by any warranty or condition, express, implied or statutory.

• LICENSEE REMEDIES. AMX's entire liability and Licensee's exclusive remedy shall be repair or replacement of the AMX Soft-

ware that does not meet AMX's Limited Warranty and which is returned to AMX in accordance with AMX's current return policy.

This Limited Warranty is void if failure of the AMX Software has resulted from accident, abuse, or misapplication. Any replace-

ment AMX Software will be warranted for the remainder of the original warranty period or thirty (30) days, whichever is longer.

Outside the United States, these remedies may not available. NO LIABILITY FOR CONSEQUENTIAL DAMAGES. IN NO

EVENT SHALL AMX BE LIABLE FOR ANY DAMAGES WHATSOEVER (INCLUDING, WITHOUT LIMITATION, DAMAGES

FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, OR ANY OTHER

PECUNIARY LOSS) ARISING OUT OF THE USE OF OR INABILITY TO USE THIS AMX SOFTWARE, EVEN IF AMX HAS

BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. BECAUSE SOME STATES/COUNTRIES DO NOT ALLOW

THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE ABOVE LIMITA-

TION MAY NOT APPLY TO LICENSEE.

• U.S. GOVERNMENT RESTRICTED RIGHTS. The AMX Software is provided with RESTRICTED RIGHTS. Use, duplication, or

disclosure by the Government is subject to restrictions as set forth in subparagraph ©(1)(ii) of The Rights in Technical Data and

Computer Software clause at DFARS 252.227-7013 or subparagraphs ©(1) and (2) of the Commercial Computer Software

Restricted Rights at 48 CFR 52.227-19, as applicable.

• SOFTWARE AND OTHER MATERIALS FROM AMX.COM MAY BE SUBJECT TO EXPORT CONTROL. The United States

Export Control laws prohibit the export of certain technical data and software to certain territories. No software from this Site may

be downloaded or exported (i) into (or to a national or resident of) Cuba, Iraq, Libya, North Korea, Iran, Syria, or any other coun-

try to which the United States has embargoed goods; or (ii) anyone on the United States Treasury Department's list of Specially

Designated Nationals or the U.S. Commerce Department's Table of Deny Orders. AMX does not authorize the downloading or

exporting of any software or technical data from this site to any jurisdiction prohibited by the United States Export Laws.

This Agreement replaces and supersedes all previous AMX Software License Agreements and is governed by the laws of

the State of Texas, and all disputes will be resolved in the courts in Collin County, Texas, USA. For any questions concern-

ing this Agreement, or to contact AMX for any reason, please write: AMX License and Warranty Department, 3000 Research

Drive, Richardson, TX 75082.

Table of Contents

NI-3101-SIG Signature Series NetLinx Integrated Controller

Table of Contents

Introduction ........................................................................................................1

NI-3101-SIG Specifications........................................................................................ 2

Installation and Upgrading .................................................................................5

Device:Port:System (D:P:S) ....................................................................................... 5

Installation into an Equipment Rack.......................................................................... 5

Connections and Wiring .....................................................................................7

Setting the Configuration DIP Switch for the Configuration Port............................. 7

Program Run Disable (PRD) mode................................................................................... 7

Working with the Configuration DIP switch .................................................................... 7

Configuration Port Connections and Wiring ............................................................. 7

Modes and Front Panel LED Blink Patterns .............................................................. 8

Port Assignments and Functionality.......................................................................... 8

AXlink Port and LED ................................................................................................. 8

Wiring Guidelines ..................................................................................................... 9

Wiring length guidelines ................................................................................................. 9

Preparing captive wires................................................................................................... 9

Wiring a power connection ............................................................................................. 9

Using the 4-pin mini-Phoenix connector for data and power ........................................ 10

Using the 4-pin mini-Phoenix connector for data with external power ......................... 10

DB9 Device Port: Connections and Wiring ............................................................. 11

Relay Port: Connections and Wiring ....................................................................... 11

Relay connections.......................................................................................................... 11

Input/Output (I/O) Port: Connections and Wiring................................................... 12

IR/Serial Port: Connections and Wiring................................................................... 12

LAN (Ethernet/RJ-45 Port): Connections and Wiring .............................................. 13

LAN LEDs ..................................................................................................................... 14

LAN ports used by the Integrated Controllers.............................................................. 14

Replacing the Timekeeper Battery ......................................................................... 14

Configuration and Firmware Update ................................................................17

Overview ................................................................................................................ 17

Communicating with the Master via the Program Port........................................... 17

Setting the System Value........................................................................................ 18

Using Multiple NetLinx Masters .................................................................................... 20

Changing the Device Address of a NetLinx Device ................................................ 20

Recommended NetLinx Device Numbers...................................................................... 21

Using the ID Button to Change the Controller’s Device Value ............................... 21

NI-3101-SIG Signature Series NetLinx Integrated Controller

Table of Contents

Resetting the Factory Default System and Device Values....................................... 22

Obtaining the Master’s IP Address (using DHCP) ................................................... 23

Assigning a Static IP to the NetLinx Master............................................................ 24

Communicating with the NI Device via an IP .......................................................... 26

Verifying the current version of NetLinx Master Firmware ..................................... 28

Upgrading the On-board Master Firmware via an IP .............................................. 29

Upgrading the NI Controller Firmware via IP.......................................................... 31

NetLinx Security within the Web Server ...........................................................33

NetLinx Security Terms ........................................................................................... 34

Accessing an Unsecured Master via an HTTP Address ............................................ 34

Browser Application Frames ................................................................................... 35

Default Security Configuration ............................................................................... 35

Master Firmware Security Access Parameters ........................................................ 37

Web Control ........................................................................................................... 37

Managing WebControl Connections.............................................................................. 37

Security Features .................................................................................................... 38

Security - System Level Security page ........................................................................... 39

Setting the system security options for a NetLinx Master............................................. 42

ICSP Authentication ...................................................................................................... 43

Security - Group Level Security page ............................................................................ 44

Adding a new Group ..................................................................................................... 46

Modifying the properties of an existing Group............................................................. 46

Deleting an existing Group ........................................................................................... 46

Security - User Level Security page ............................................................................... 47

Adding a new User........................................................................................................ 49

Modifying the properties of an existing User................................................................ 50

Deleting an existing User .............................................................................................. 50

System Settings ...................................................................................................... 51

System Settings - Manage System page........................................................................ 51

Manage System - System Menu Buttons................................................................. 54

System Menu - Modifying the Date/Time...................................................................... 54

System Menu - Changing the System Number .............................................................. 54

System Menu - Rebooting the Master ........................................................................... 55

System Menu - Controlling/Emulating Devices on the Master ...................................... 55

Manage System - Diagnostics........................................................................................ 57

Setting up and removing a Diagnostic Filter ................................................................. 58

Setting the Master’s Port Configurations ............................................................... 61

Manage System - Server................................................................................................ 61

Modifying the Server Port Settings ............................................................................... 62

Table of Contents

iii

NI-3101-SIG Signature Series NetLinx Integrated Controller

SSL Server Certificate Creation Procedures............................................................ 64

Server - Display SSL Server Certificate Information ...................................................... 66

Server - Creating a self-generated SSL Certificate ........................................................ 66

Server - Regenerating an SSL Server Certificate Request ............................................. 67

Server - Creating a Request for an SSL Certificate........................................................ 67

Common Steps for Requesting a Certificate from a CA.......................................... 68

Communicating with the CA ......................................................................................... 68

Server - Exporting an SSL Certificate Request .............................................................. 68

Server - Importing a CA created SSL Certificate ........................................................... 69

Manage System - Device Menu Buttons ................................................................. 71

Device Menu - Configuring the LAN Settings ............................................................... 71

Device Menu - Developing a URL List ........................................................................... 72

Device Menu - Changing the Device Number ............................................................... 73

Device Menu - Controlling or Emulating a device ......................................................... 74

Device Menu - Viewing the Log .................................................................................... 74

Device Menu - Running a Diagnostic Filter.................................................................... 74

System Settings - Manage License.......................................................................... 74

Adding a new license .................................................................................................... 75

Removing a license........................................................................................................ 76

System Settings - Manage NetLinx Devices............................................................ 76

Manage NetLinx Devices - Displaying NDP-capable devices......................................... 78

Manage NetLinx Devices - Binding/Unbinding - Explained ........................................... 78

Manage NetLinx Devices - Obtaining NetLinx Device information ............................... 79

System Settings - Manage Other Devices - Dynamic Device Discovery Pages........ 80

What is Dynamic Device Discovery?.............................................................................. 83

What is the difference between Program and Run-time defined binding? ................... 84

Manage Other Devices - Manage Device Bindings ................................................. 85

Configuring application-defined devices....................................................................... 85

What are Application Devices and their association status? ......................................... 87

Manage Other Devices Menu - Viewing Discovered Devices ........................................ 88

Manage Other Devices Menu - Creating a new User-Defined Device ........................... 89

How do I write a program that uses Dynamic Device Discovery ................................... 90

How do I configure a Run-time installation ................................................................... 91

Accessing an SSL-Enabled Master via an IP Address .............................................. 92

Using your NetLinx Master to control the G4 panel...................................................... 95

What to do when a Certificate Expires ................................................................... 97

NetLinx Security with a Terminal Connection ...................................................99

Overview ................................................................................................................ 99

NetLinx Security Features....................................................................................... 99

NI-3101-SIG Signature Series NetLinx Integrated Controller

Table of Contents

Initial Setup via a Terminal Connection................................................................... 99

Establishing a Terminal connection via the RS-232/USB Configuration Port ............... 100

Accessing the Security configuration options ....................................................... 100

Option 1 - Set system security options for NetLinx Master (Security Options Menu) . 101

Option 2 - Display system security options for NetLinx Master .................................. 102

Option 3 - Add user .................................................................................................... 103

Option 4 - Edit User .................................................................................................... 103

Edit User Menu............................................................................................................ 103

Access Rights Menu..................................................................................................... 104

Option 5 - Delete user................................................................................................. 105

Option 6 - Show the list of authorized users ............................................................... 105

Option 7 - Add Group ................................................................................................. 105

Edit Group Menu......................................................................................................... 105

Edit Group menu: Delete directory association........................................................... 106

Edit Group menu: List directory associations .............................................................. 107

Edit Group menu: Change Access Rights .................................................................... 107

Edit Group menu: Display Access Rights..................................................................... 107

Option 8 - Edit Group ................................................................................................. 107

Option 9 - Delete Group ............................................................................................. 108

Option 10 - Show List of Authorized Groups .............................................................. 108

Option 11 - Set Telnet Timeout in seconds ................................................................. 108

Option 12 - Display Telnet Timeout in seconds ........................................................... 108

Option 13 - Make changes permanent by saving to flash ........................................... 108

Main Security Menu .............................................................................................. 109

Default Security Configuration ............................................................................. 110

Help menu ................................................................................................................... 111

Logging Into a Session.......................................................................................... 113

Logout .................................................................................................................. 113

Help Security ............................................................................................................... 113

Setup Security ............................................................................................................. 114

Programming ..................................................................................................115

Converting Axcess Code to NetLinx Code............................................................ 115

Master Send_Commands ...................................................................................... 115

Master IP Local Port Send_Commands ................................................................. 117

Using the ID Button .............................................................................................. 117

Device:Port:System (D:P:S).......................................................................................... 118

Configuration Port Commands ............................................................................. 118

ESC Pass Codes .................................................................................................... 131

Notes on Specific Telnet/Terminal Clients ............................................................ 131

Table of Contents

NI-3101-SIG Signature Series NetLinx Integrated Controller

WindowsTM client programs....................................................................................... 131

Linux Telnet client ....................................................................................................... 131

LED Disable/Enable Send_Commands .................................................................. 132

RS232/422/485 Ports Channels ............................................................................ 132

RS-232/422/485 Send_Commands ....................................................................... 132

RS-232/422/485 Send_String Escape Sequences.................................................. 135

IR / Serial Ports Channels ..................................................................................... 136

IR/Serial Send_Commands .................................................................................... 136

Input/Output Send_Commands ............................................................................ 142

Troubleshooting .............................................................................................143

NI-3101-SIG Signature Series NetLinx Integrated Controller

Table of Contents

Introduction

NI-3101-SIG Signature Series NetLinx Integrated Controller

Introduction

The NI-3101-SIG Signature Series NetLinx Integrated Controller satisfies the control and automation features

common in a larger area or multiple rooms, which may include the integration of a larger number of devices

including VCR and DVD players, projectors, lighting, thermostats and other electronic equipment. In

technology-driven environments, this solution allows for the future addition of more devices and control

capabilities.

The NI-3101-SIG features an easy-to-install form factor that mounts into 1 unit of rack space and provides

extended rack depth to simplify rear connections. Its sleek, gloss black faceplate complements the Tango

Distributed Audio line and Metreau Keypads. For smaller business and home applications, the NI-3101-SIG

includes just the right mix of ports and features.

The NI-3101-SIG is Duet-compatible and can be upgraded via firmware. Duet is a dual-interpreter firmware

platform from AMX which combines the proven reliability and power of NetLinx with the extensive

capabilities of the Java

2 MicroEdition (J2ME) platform. Duet simplifies the programming of a system that

includes third party devices by standardizing device and function definitions, defaulting touch panel button

assignments, and controlling feedback methods. Dynamic Device Discovery makes integration even easier by

automatically identifying and communicating with devices which support this new beaconing technology.

Refer to the System Settings - Manage Other Devices - Dynamic Device Discovery Pages section on page 80

for more detailed information on the use of Dynamic Device Discovery (DDD).

The NI-3101-SIG uses a combination lithium battery and clock crystal package called a Timekeeper. Only one

Timekeeper unit is installed within a given NI-3101. The battery can be expected to have up to 3 years of

usable life under very adverse conditions. Actual life is appreciably longer under normal operating conditions.

This calculation is based on storing the unit without power in 50° C (120° F) temperature until battery levels

are no longer acceptable. The part number for a replacement battery is 57-0032.

NetLinx Integrated Master Controller Features

NI-3101-SIG

(FG2105-08)

• 1 low-speed USB connection for configuration

• 6 RS-232/RS-422/RS-485 ports

• 8 IR/Serial Output ports

• 8 Digital Input/Output ports

•8 Relays

RISK OF EXPLOSION IF BATTERY IS REPLACED WITH AN INCORRECT TYPE.

DISPOSE OF USED BATTERIES ACCORDING TO MANUFACTURER’S

INSTRUCTIONS.

Introduction

NI-3101-SIG Signature Series NetLinx Integrated Controller

NI-3101-SIG Specifications

The NI-3101-SIG (FIG. 1) provides support for 6 configurable RS-232/RS-422/RS-485 Ports, 8 IR/Serial

Output ports, 8 Digital Input/Output ports, and 8 Relays.

FIG. 1 NI-3101 NetLinx Integrated Controller (front view)

FIG. 2 NI-3101 front and rear panel connectors and components

NI-3101-SIG Specifications (Cont.)

Dimensions (HWD): • 2" (with feet) x 17" x 10" (5.1 cm x 43.2 cm x 26.35 cm)

• 1 RU (rack unit) high

Power Requirement: 900 mA @ 12 VDC

Memory: • 64 MB SDRAM

• 256 MB Flash

• 1 MB Non-volatile (NV) SRAM

Compact Flash: 128 MB Card (upgradeable) (refer to the Other AMX Equipment section for

more information)

Weight: 6.95 lbs (3.15 kg)

Enclosure: Metal with black matte finish and translucent polycarbonate faceplate

Certifications: • FCC Part 15 Class B

•CE

• IEC 60950

Front Panel Components:

POWER Blue LED bar lights when powered up

LINK/ACTIVE Blue LED blinks when the LAN cable is connected and an active link is

established. This LED also blinks when receiving LAN data packets.

Status Blue LED blinks to indicate that the system is programmed and

communicating properly.

Link/Active-Status-I/O

RS-232/422/485

TX/RX LEDs

Relay LEDs

I/O LEDs

IR/Serial LEDs

Power

Front

RS-232/422/485

Ports (1-6)

Relays

(Port 8)

I/O

(Port 17)

IR/Serial

(Ports 9-16)

Configuration

switches

Programming

Port

switch

LAN

10/100

Port

AXLink

Power

12 VDC

LED

AXLink

Port

Rear

Introduction

NI-3101-SIG Signature Series NetLinx Integrated Controller

NI-3101-SIG Specifications (Cont.)

Input/Output LEDs White Output LED blinks when the Controller transmits data, sets channels

On/Off, sends data strings, etc. White Input LED blinks when it receives data

from button pushes, strings, commands, channel levels, etc.

RS-232/422/485 LEDs Six sets of blue and white LEDs light to indicate the rear serial Ports 1 - 6 are

transmitting or receiving RS-232, 422, or 485 data:

• TX LEDs (blue) light when transmitting data

• RX LEDs (white) light when receiving data

• LED activity reflects transmission and reception activity

Relay LEDs Eight blue LEDs light to indicate the rear relay channels 1 - 8 are active

(closed).

• These LEDs reflect the state of the relay on Port 8

• If the relay is engaged = LED On and if the relay is Off = LED Off

IR/Serial LEDs Eight blue LEDs light to indicate the rear IR/Serial channels 1 - 8 are

transmitting control data on Ports 9 - 16.

• LED indicator for each IR port remains lit for the length of time that IR/Serial

data is being generated.

I/O LEDs Eight white LEDs light when the rear I/O channels 1-8 are active

• LED indicator for each I/O port reflects the state of that particular port.

Rear Panel Connectors:

RS-232/422/485 (Ports 1 - 6) Six RS-232/422/485 control ports using DB9 (male) connectors with XON/

XOFF (transmit on/transmit off), CTS/RTS (clear to send/ready to send), and

300-115,200 baud.

• Channel range = 1-255

• Channels 1-254 provide feedback

• Channel 255 (CTS Push channel): Reflects the state of the CTS Input if a

'CTSPSH' command was sent to the port

• Output data format for each port is selected via software

• Six DB9 connectors provide RS-232/422/485 termination

Relay (Port 8) Eight-channel single-pole single-throw relay ports.

• Each relay is independently controlled.

• Supports up to 8 independent external relay devices

• Channel range = 1-8

• Each relay can switch up to 24 VDC or 28 VAC @ 1 A

• Two 8-pin 3.5 mm mini-Phoenix (female) connectors provide relay

termination

Digital I/O (Port 17) Eight-channel binary I/O port for contact closure.

• Each input is capable of voltage sensing. Input format is software

selectable.

• Interactive power sensing for IR ports

• Channel range = 1-8

• All inputs are assigned to respective IR/Serial ports for "automatic" power

control through the use of software commands. Power control is provided

via commands such as: ’PON’, ’POF’, ’POD’, ’DELAY’, I/O Link etc.).

• Contact closure between GND and an I/O port is detected as a PUSH

• When used as voltage input - I/O port detects a low signal (0- 1.5 VDC) as a

PUSH and a high signal (3.5 - 5 VDC) as a RELEASE

• When used as an output - each I/O port acts as a switch to GND and is

rated at 200 mA @ 12 VDC

• 10-pin 3.5 mm mini-Phoenix (female) connector provides I/O port

termination

Note: This IO port uses 5V logic, but can handle up to 12V on the input

without harm. Higher voltages run a higher risk of surge damage.

Introduction

NI-3101-SIG Signature Series NetLinx Integrated Controller

NI-3101-SIG Specifications (Cont.)

IR/Serial (Ports 9 - 16) Eight IR/Serial control ports support high-frequency carriers up to

1.142 MHz.

• Each output is capable of three electrical formats: IR, Serial, and Data

• Eight IR/Serial data signals can be generated simultaneously.

• Channel range = 1-32,767

• Channels 1-128 (output): IR commands

• Channels 129-253: used as reference channels

• Channel 254 (feedback): Power Fail (used with 'PON' and 'POF'

commands)

• Channel 255 (feedback): Power status (when IO Link is set)

• IR ports support data mode (at limited baud rates and wiring distances).

• Two 8-pin 3.5 mm mini-Phoenix (female) connectors provide IR/Serial port

termination

Configuration Port USB connector (male) can be connected to a USB port on a computer. This

low-speed USB connection is used to configure system settings.

Not recommended for firmware updates or large file transfers.

Configuration DIP switch 4 configuration DIP switches used solely for enabling or disabling NetLinx

functionality.

ID pushbutton Provides the NetLinx ID (Device only) assignment for the device. Refer to

the Changing the Device Address of a NetLinx Device section on page 20.

• The D notation is used to represent a device number.

LAN port RJ-45 port for 10/100 Mbps communication.

This port automatically negotiates the connection speed (10 Mbps or 100

Mbps) and whether to use half duplex or full duplex mode.

LAN Link/Activity LED LEDs show communication activity, connection status, speeds, and mode

information:

• SPD (speed) - Yellow LED lights On when the connection speed is 100

Mbps and turns Off when the speed is 10 Mbps.

• L/A (link/activity) - Green LED lights On when the LAN cables are

connected/terminated correctly, and blinks when receiving LAN data

packets.

AXlink LED • Green LED indicates the state of the AXlink connector port.

• Normal AXlink activity = 1 blink/second

• Abnormal AXlink activity = cycle of 3 consecutive blinks and then Off

AXlink port 4-pin 3.5 mm mini-Phoenix (male) connector provides data and power to

external control devices.

Power port 2-pin 3.5 mm mini-Phoenix (male) connector

Included Accessories: • 2-pin 3.5 mm mini-Phoenix (female) PWR connector (41-5025)

• 4-pin 3.5 mm mini-Phoenix (female) AXlink connector (41-5047)

• 10-pin 3.5 mm mini-Phoenix (female) I/O connector (41-5107)

• Installation Kit (KA2105-02):

Two rack mount ears

Four #8-32 Phillips flat head screws

• NI-3101-SIG Quick Start Guide (93-2105-08)

• Two 8-pin 3.5 mm mini-Phoenix (female) Relay connectors (41-5083)

• Two CC-NIRC IR Emitters

Other AMX Equipment: • 2-pin 3.5 mm mini-Phoenix male connector (41-5026)

• CC-NIRC IR cables (FG10-000-11)

• CC-NSER IR/Serial cables (FG10-007-10)

• CSB Cable Support Bracket (FG517)

• NCK, NetLinx Connector Kit (FG2902)

• USB A to B cable (FG10-2105)

Installation and Upgrading

NI-3101-SIG Signature Series NetLinx Integrated Controller

Installation and Upgrading

Device:Port:System (D:P:S)

A device is any hardware component that can be connected to an AXlink bus. Each device must be assigned a

unique number to locate that device on the bus. Only the Device value can be set through the DIP switch

settings mentioned above.

NetLinx requires a Device:Port:System (D:P:S) specification. This D:P:S triplet can be expressed as a series of

constants, variables separated by colons, or a DEV structure. For example:

STRUCTURE DEV

{

INTEGER Number // Device number

INTEGER Port // Port on device

INTEGER System // System the device belongs to

}

The D:P:S notation is used to explicitly represent a device number, port and system. For example, 128:1:0

represents the first port on device 128 on this system.

If a device is declared in a NetLinx program with just the Device number (System and Port are omitted), the

NetLinx Compiler assumes it has a Port number of 1 and a System number of 0. However, all existing

device declarations should be converted using the D:P:S (Device:Port:System) notation. This enables certain

NetLinx specific debugging features and can help pinpoint other potentially obscure errors.

The syntax is as follows:

NUMBER:PORT:SYSTEM

where:

Installation into an Equipment Rack

Use the rack-mounting ears supplied with the NI-3101-SIG controller for equipment rack installations. The

device comes installed with four rubber feet for flat surface installations.

1. Discharge the static electricity from your body by touching a grounded object.

2. Position and install the mounting ears, using the screws supplied with the unit. The mounting ears may be

rotated to accommodate your mounting needs.

NUMBER: 16-bit integer represents the device number

PORT: 16-bit integer represents the port number (in the range 1 through the number of

ports on the Controller or device)

SYSTEM: 16-bit integer represents the system number (0 = this system)

The maximum operating ambient temperature is 40°C.

Connect the unit only to a properly-rated supply circuit.

Never restrict the airflow through the devices’ fan or vents.

When installing equipment into a rack, distribute the units evenly. Otherwise,

hazardous conditions may be created by an uneven weight distribution.

Reliable earthing (grounding) of rack-mounted equipment should be maintained.

Before completing the install process, completing any firmware upgrade of the

NetLinx Control Cards is highly recommended. This upgrade involves physically

cycling power to the unit and can become cumbersome if the unit is already installed

into a rack.

Installation and Upgrading

NI-3101-SIG Signature Series NetLinx Integrated Controller

3. Thread the cables through the opening in the equipment rack. Allow for enough slack in the cables to

accommodate for movement during the installation process.

4. Reconnect all cables to their appropriate source/terminal locations. Refer to theConnections and

Wiring section on page 7 for more detailed wiring and connection information.

Verify that the terminal end of the power cable is not connected to the a power supply before

plugging in the 2-pin power connector.

5. Slide the device into the rack until the attachment holes, along both sides, align to their corresponding

locations on the mounting ears.

6. Secure the device to the rack by using the four flat-head Phillips screws supplied in the kit.

7. Apply power to the unit to complete the installation.

1. If installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack

environment may be greater than room ambient. Therefore, consideration should be given to installing

the equipment in an environment compatible with the maximum ambient temperature 50°C.

2. Installation of the equipment in a rack should be such that the amount of air flow required for safe

operation of the equipment is not compromised.

3. Mounting of the equipment in the rack should be such that a hazardous condition is not achieved due to

uneven mechanical loading.

4. Consideration should be given to the connection of the equipment to the supply circuit and the effect that

overloading of the circuits might have on over current protection and supply wiring. Appropriate

consideration of equipment nameplate ratings should be used when addressing this concern.

5. Reliable earthing of rack-mounted equipment should be maintained. Particular attention should be given

to supply connections other than direct connections to the branch circuit (e.g. use of power strips).

To prevent repetition of the installation, test the incoming wiring by connecting the

Controller’s connectors to their terminal locations and applying power. Verify that the

unit is receiving power and functioning properly. Disconnect the terminal end of the

power cable from the connected 12 VDC-compliant power supply.

CAUTION: RACK MOUNT SAFETY INSTRUCTIONS

Connections and Wiring

NI-3101-SIG Signature Series NetLinx Integrated Controller

Connections and Wiring

Setting the Configuration DIP Switch for the Configuration

Port

Prior to installing the Controller, use the Configuration DIP switch to set the information used by the

Configuration Port for communication. The DIP switchsets the starting address (the device number in the

D:P:S specification) for the Control Cards installed in the controller with a range of 1-1536. The four-pin

Configuration DIP switch is located on the rear of the device.

Program Run Disable (PRD) mode

The Configuration DIP switch is used to set the on-board Master to Program Run Disable (PRD) mode,

according to the settings listed in the table below.

The PRD mode prevents the NetLinx program stored in the on-board Master from running during the device’s

power-up. This mode should only be used if the resident NetLinx program is causing inadvertent

communication and/or control problems. If necessary, place the on-board Master in PRD mode and use the

NetLinx Studio v 2.x program to resolve the communication and/or control problems with the resident

NetLinx program. After doing so, download the corrected program, reset the configuration DIP switch to

normal mode, recycle power, and try again.

Working with the Configuration DIP switch

Disconnect the power supply from the 2-pin PWR (green) connector on the rear of the NetLinx Integrated

Controller.

2. Set DIP switch positions according to the information listed in thePRD Mode Settings table.

3. Reconnect the 12 VDC power supply to the 2-pin 3.5 mm mini-Phoenix PWR connector.

Configuration Port Connections and Wiring

The NI-3101 is equipped with a low-speed USB connection located on the rear of the unit. Use a standard

USB cable to establish a connection between the device and your PC's USB port. This connection provides

communication with the NetLinx Integrated Controller. From there, configure the on-board Master as needed

for your application.

PRD Mode Settings

PRD Mode Position 1

Normal mode (default) OFF

PRD Mode ON

Think of the PRD Mode (On) equating to a PC’s SAFE Mode setting. This mode

allows a user to continue powering a unit, update the firmware, and download a new

program while circumventing any problems with a currently downloaded program.

Power must be cycled to the unit after activating/deactivating this mode on the

Configuration Port DIP switch #1.

Connections and Wiring

NI-3101-SIG Signature Series NetLinx Integrated Controller

Modes and Front Panel LED Blink Patterns

The following table lists the modes and blink patterns for the front panel LEDs associated with each mode.

These patterns are not evident until after the unit is powered.

Port Assignments and Functionality

The rear Port Assignments are as follows:

AXlink Port and LED

All NI units have an AXlink port and adjacent status LED (FIG. 3). This port allows the NI to support AMX

legacy AXlink devices such as G3 touch panels (ex: CP4/A) and PosiTrack Pilot devices. A green LED shows

AXlink data activity. When the AXlink port is operating normally, blink patterns include:

Off - No power, or the controller is not functioning properly.

1 blink per second - Normal operation.

3 blinks per second - AXlink bus error. Check all AXlink bus connections.

Modes and LED Blink Patterns

LEDs and Blink Patterns

Mode Description

STATUS

(blue)

OUTPUT

(white)

INPUT

(white)

OS Start Starting the operating system (OS). On On On

Boot On-board Master is booting. On Off On

Contacting DHCP

server

On-board Master is contacting a DHCP

server for IP configuration information.

On Off Fast Blink

Unknown DHCP

server

On-board Master could not find the DHCP

server.

Fast Blink Off Off

Downloading Boot

firmware

Downloading Boot firmware to the Master’s

on-board flash memory.

Do not cycle power during this process!

Fast Blink Fast Blink Fast Blink

No program running Either no program is loaded, or the

program is disabled.

On Normal Normal

Normal On-board Master is functioning normally. 1 blink per

second

Indicates

activity

Indicates

activity

NI-3101 Port Assignments

Port ICSP Port # Port ICSP Port #

Serial Port #1 1 IR Serial Port #1 9

Serial Port #2 2 IR Serial Port #2 10

Serial Port #3 3 IR Serial Port #3 11

Serial Port #4 4 IR Serial Port #4 12

Serial Port #5 5 IR Serial Port #5 13

Serial Port #6 6 IR Serial Port #6 14

Relays Ports (1-8) 8 IR Serial Port #7 15

IR Serial Port #8 16

I/O Port 17

FIG. 3

AXlink connector and LED

GND

AXM

AXP

PWR

AXLink

Connections and Wiring

NI-3101-SIG Signature Series NetLinx Integrated Controller

The AXlink port can be used to supply power to downstream AXlink-compatible devices, so long as both the

power required is LESS THAN 2 Amps total and the external power supply feeding the device has the

necessary power capability.

Wiring Guidelines

The Integrated Controllers use a 12 VDC-compliant power supply to provide power through the rear

2-pin 3.5 mm mini-Phoenix PWR connector, or through the 4-pin 3.5 mm mini-Phoenix (female) captive-wire

connector used for data communication and power transfer. Use the power requirements referenced in the

product’s Specifications table to determine the power draw.

The incoming PWR and GND cable from the power supply must be connected to the corresponding locations

within the PWR connector.

Wiring length guidelines

Refer to the following table for the wiring length information used with the NI-3101:

Preparing captive wires

You will need a wire stripper and flat-blade screwdriver to prepare and connect the captive wires.

1. Strip 0.25 inch (6.35 mm) of insulation off all wires.

2. Insert each wire into the appropriate opening on the connector (according to the wiring diagrams and

connector types described in this section).

3. Tighten the screws to secure the wire in the connector. Do not tighten the screws excessively. Doing so

may strip the threads and damage the connector.

Wiring a power connection

To use the 2-pin 3.5 mm mini-Phoenix connector with a 12 VDC-compliant power supply, the incoming PWR

and GND cables from the external source must be connected to their corresponding locations on the connector

(FIG. 4).

1. Insert the PWR and GND wires on the terminal end of the 2-pin 3.5 mm mini-Phoenix cable. Match the

wiring locations of the +/- on both the power supply and the terminal connector.

2. Tighten the clamp to secure the two wires. Do not tighten the screws excessively; doing so may strip the

threads and damage the connector.

3. Verify the connection of the 2-pin 3.5 mm mini-Phoenix to the external 12 VDC-compliant power supply.

Use only one power source for the device at a time. Using both the 2-pin mini-

Phoenix PWR connector and the 4-pin mini-Phoenix AXLink connector at the same

time may cause permanent damage to the device.

Apply power to the device only after installation is complete.

Wiring Guidelines - NI-3101 @ 900 mA

Wire size Maximum wiring length

18 AWG 120.41 feet (39.70 meters)

20 AWG 76.45 feet (23.30 meters)

22 AWG 49.36 feet (15.04meters)

24 AWG 30.08 feet (9.17 meters)

Never pre-tin wires for compression-type connections.

Connections and Wiring

NI-3101-SIG Signature Series NetLinx Integrated Controller

Using the 4-pin mini-Phoenix connector for data and power

Connect the 4-pin 3.5 mm mini-Phoenix (female) captive-wire connector to an external NetLinx device as

shown in FIG. 5.

Using the 4-pin mini-Phoenix connector for data with external power

To use the 4-pin 3.5 mm mini-Phoenix (female) captive-wire connector for data communication and power

transfer, the incoming PWR and GND cable from the 12 VDC-compliant power supply must be connected to

the AXlink cable connector going to the device (FIG. 6). Always use a local power supply to power the device.

Make sure to connect only the GND wire on the AXlink/PWR connector when using a separate

12 VDC power supply. Do not connect the PWR wire to the AXlink connector’s PWR (+) opening.

FIG. 4 2-pin mini-Phoenix connector wiring diagram (direct power)

FIG. 5 Mini-Phoenix connector wiring diagram (direct data and power)

FIG. 6 4-pin mini-Phoenix connector wiring diagram (using external power source)

PWR +

GND -

Integrated Controller

Power Supply

To the Integrated Controller’s

To the external AXlink device

AXlink/PWR connector

PWR +

AXP/TX

AXM/RX

GND -

Top view

PWR +

AXP/TX

AXM/RX

GND -

PWR (+)

GND (-)

Local +12 VDC

(coming from

To the Integrated Controller’s

To the external AXlink device

AXlink/PWR connector

power supply

an external

power supply)

Top view

AXP/TX

AXM/RX

GND -

AXP/TX

AXM/RX

GND -

When you connect an external power supply, do not connect the wire from the PWR

terminal (coming from the external device) to the PWR terminal on the Phoenix

connector attached to the Controller unit. Make sure to connect only the AXM, AXP,

and GND wires to the Controller’s Phoenix connector when using an external power

supply.

Page is loading ...

AMX Switch NI-3101-SIG User manual

Brand: AMX

Model: Switch NI-3101-SIG

Type: User manual

This manual is also suitable for

NI-3101-SIG

Download PDF

report

AMX Switch NI-3101-SIG User manual

This manual is also suitable for

AMX Switch NI-3101-SIG User manual

Related papers

Other documents