WAGO 8-channel, 24VDC, 0.5A User manual

Pos: 2 /Dokumentation allgemein/Einband/Einband Handbuch - Deckbl at t oh ne V aria nt enfel d (S ta ndar d) @ 9 \mod_1285229289866_0.docx @ 64941 @ @ 1

Manual

WAGO-I/O-SYSTEM 750

8DO 24V DC 0.5A

753-530(/xxx-xxx)

8-Channel Digital Output Module 24 V DC, Short-

circuit protected; high-side switching

Version 1.1.0

Pos: 3 /A lle Ser ien ( All ge mein e M odul e)/ Hin weis e z ur D oku men tati on/I mpr ess um für Sta ndar dh and büch er - al lg. A ngabe n, Ansc hrifte n, Telef onn ummer n und E-Mai l-A dresse n @ 3\mod_1219151118203_21.docx @ 21060 @ @ 1

2 WAGO-I/O-SYSTEM 750

753-530 8DO 24V DC 0.5A

Manual

Version 1.1.0

WAGO Kontakttechnik GmbH & Co. KG

Hansastraße 27

D-32423 Minden

Phone: +49 (0) 571/8 87 – 0

Fax: +49 (0) 571/8 87 – 1 69

E-Mail: [email protected]

Web: http://www.wago.com

Technical Support

Phone: +49 (0) 571/8 87 – 5 55

Fax: +49 (0) 571/8 87 – 85 55

E-Mail: [email protected]

Every conceivable measure has been taken to ensure the accuracy and

completeness of this documentation. However, as errors can never be fully

excluded, we always appreciate any information or suggestions for improving the

documentation.

E-Mail: [email protected]

We wish to point out that the software and hardware terms as well as the

trademarks of companies used and/or mentioned in the present manual are

generally protected by trademark or patent.

=== Ende der Lis te f ür T e xtmar ke Ei nb and _vor ne = ==

WAGO-I/O-SYSTEM 750 Table of Contents 3

753-530 8DO 24V DC 0.5A

Manual

Version 1.1.0

Pos: 5 /D ok ument ati on al lg em ein/V erz eic hni sse /Inh alts ver zei chni s - Ü bersc hrift oG und Ver zeich nis @ 3\mod_1219151230875_21.docx @ 21063 @ @ 1

Table of Contents

1 Notes about this Documentation ................................................................. 5

1.1 Validity of this Documentation ................................................................. 5

1.2 Copyright ................................................................................................... 5

1.3 Symbols ..................................................................................................... 6

1.4 Number Notation ....................................................................................... 8

1.5 Font Conventions ...................................................................................... 8

2 Important Notes ........................................................................................... 9

2.1 Legal Bases ............................................................................................... 9

2.1.1 Subject to Changes ............................................................................... 9

2.1.2 Personnel Qualifications ....................................................................... 9

2.1.3 Use of the WAGO-I/O-SYSTEM 750 in Compliance with Underlying

Provisions ............................................................................................. 9

2.1.4 Technical Condition of Specified Devices ......................................... 10

2.2 Safety Advice (Precautions) .................................................................... 11

3 Device Description ..................................................................................... 13

3.1 View ........................................................................................................ 15

3.2 Connectors ............................................................................................... 16

3.2.1 Data Contacts/Internal Bus ................................................................. 16

3.2.2 Power Jumper Contacts/Field Supply ................................................ 17

3.2.3 CAGE CLAMP

®

Connectors ............................................................. 19

3.3 Display Elements .................................................................................... 20

3.4 Schematic Diagram ................................................................................. 21

3.5 Technical Data ........................................................................................ 22

3.5.1 Device Data ........................................................................................ 22

3.5.2 Power Supply...................................................................................... 22

3.5.3 Communication .................................................................................. 22

3.5.4 Outputs ............................................................................................... 22

3.5.5 Connection .......................................................................................... 23

3.5.6 Climatic Environmental Conditions ................................................... 23

3.6 Approvals ................................................................................................ 24

3.7 Standards and Guidelines ........................................................................ 26

4 Process Image ............................................................................................. 27

5 Mounting ..................................................................................................... 28

5.1 Mounting Sequence ................................................................................. 28

5.2 Inserting and Removing Devices ............................................................ 29

5.2.1 Inserting the I/O Module .................................................................... 29

5.2.2 Removing the I/O Module .................................................................. 30

5.3 I/O Modules with Pluggable Wiring Level (Series 753) ........................ 31

5.3.1 Coding ................................................................................................ 32

5.3.2 Connector Removal ............................................................................ 34

6 Connect Devices ......................................................................................... 35

6.1 Connecting a Conductor to the CAGE CLAMP

®

................................... 35

7 Using Interference-Free Variants of I/O Modules in Safety Related

Applications ................................................................................................ 36

4 Table of Contents WAGO-I/O-SYSTEM 750

753-530 8DO 24V DC 0.5A

Manual

Version 1.1.0

7.1 Important Notes ....................................................................................... 37

7.2 Connecting the IO Module to Safety Switching Devices or Safety

Modules ................................................................................................... 38

7.2.1 General Structure ................................................................................ 38

7.2.2 Examples of Connection..................................................................... 39

8 Use in Hazardous Environments .............................................................. 41

8.1 Marking Configuration Examples ........................................................... 42

8.1.1 Marking for Europe According to ATEX and IEC-Ex ...................... 42

8.1.2 Marking for America According to NEC 500 .................................... 47

8.2 Installation Regulations ........................................................................... 48

8.2.1 Special Conditions for Safe Use (ATEX Certificate TÜV 07 ATEX

554086 X) ........................................................................................... 49

8.2.2 Special Conditions for Safe Use (ATEX Certificate TÜV 12 ATEX

106032 X) ........................................................................................... 50

8.2.3 Special Conditions for Safe Use (IEC-Ex Certificate TUN 09.0001 X)51

8.2.4 Special Conditions for Safe Use (IEC-Ex Certificate IECEx TUN

12.0039 X) .......................................................................................... 52

8.2.5 Special Conditions for Safe Use According to ANSI/ISA 12.12.01 .. 53

List of Figures ...................................................................................................... 54

List of Tables ........................................................................................................ 55

=== Ende der Lis te f ür T e xtmar ke V erz eic hnis _vor ne == =

WAGO-I/O-SYSTEM 750 Notes about this Documentation 5

753-530 8DO 24V DC 0.5A

Manual

Version 1.1.0

Pos: 7 /A lle Ser ien ( All ge mein e M odul e)/ Über sc hrif ten für all e Ser ie n/Hi nwei se zur D o kume nt ation /Hi nw eise zu dies er D o kume ntati on - Ü b ersc hrif t 1 @ 4 \mod_1237987661750_21.docx @ 29029 @ 1 @ 1

1 Notes about this Documentation

Pos: 8 /A lle Ser ien ( All ge mein e M odul e)/ Hin weis e z ur D oku men tati on/H i nweis e/Hi n weis : D okum ent atio n a ufbe wahr e n @ 4 \mod_1237987339812_21.docx @ 29026 @ @ 1

Always retain this documentation!

This documentation is part of the product. Therefore, retain the documentation

during the entire service life of the product. Pass on the documentation to any

subsequent user. In addition, ensure that any supplement to this documentation is

included, if necessary.

Pos: 9 /A lle Ser ien ( All ge mein e M odul e)/ Über sc hrif ten für all e Ser ie n/Hi nwei se zur D o kume nt ation /G ültig kei tsb erei ch - Ü b ersc hrif t 2 @ 1 2\mod_1338912448776_21.docx @ 96469 @ 2 @ 1

1.1 Validity of this Documentation

Pos: 10 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /Hi n weis e zur D okum ent ati on/G ülti gkei ts berei c h/Gül tig kei tsber ei ch D oku men tat ion Bus kle mme 75 0-xx xx, S tan dar dvers ion un d au fg elist et e Var iant e n @ 1 4\mod_1358944038682_21.docx @ 109354 @ @ 1

This documentation is only applicable to the I/O module 753-530 (8DO 24V DC

0.5A) and the variants listed in the table below.

Pos: 11 /S eri e 7 50 ( WA GO-I/ O-SYST EM)/ Hi nweis e zur D okum ent ati on/G ülti gkei ts ber eic h/Var iant e nlist en/ Var ia ntenli st e - 7 50-xxx - Standardversion und Variante /000-800 ( rüc kwir kung sfr ei) @ 1 0\mod_1302671594038_21.docx @ 71910 @ @ 1

Table 1: Variants

Item Number/Variant

Designation

753-530

8DO 24V DC 0.5A

753-530/000-800

8DO 24V DC 0.5A/R

Pos: 12 /A ll e Ser ien (Al lg emei ne M od ule)/ Hi nweis e zur D o kume ntati on /Hi nwei se/ Hin weis : G ülti g keit d er Angaben für aufgelistete Varianten @ 9\mod_1281520778141_21.docx @ 63085 @ @ 1

Documentation Validity for Variants

Unless otherwise indicated, the information given in this documentation applies to

listed variants.

Pos: 13 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /Hi n weis e zur D okum ent ati on/Hi nw eise /Ac htu ng: H in weis zur D oku ment ati on B uskl e mmen 750- xxxx @ 4\mod_1237986979656_21.docx @ 29023 @ @ 1

The I/O module 753-530 shall only be installed and operated according to the

instructions in this manual and in the manual for the used fieldbus

coupler/controller.

Consider power layout of the WAGO-I/O-SYSTEM 750!

In addition to these operating instructions, you will also need the manual for the

used fieldbus coupler/controller, which can be downloaded at www.wago.com.

There, you can obtain important information including information on electrical

isolation, system power and supply specifications.

Pos: 14.1 /All e Seri en ( All ge meine Mo dul e)/H in weis e zur D oku ment ati on/U rh eber sc hutz aus führ lic h @ 4\mod_1235565145234_21.docx @ 27691 @ 2 @ 1

1.2 Copyright

This Manual, including all figures and illustrations, is copyright-protected. Any

further use of this Manual by third parties that violate pertinent copyright

provisions is prohibited. Reproduction, translation, electronic and phototechnical

filing/archiving (e.g., photocopying) as well as any amendments require the

written consent of WAGO Kontakttechnik GmbH & Co. KG, Minden, Germany.

Non-observance will involve the right to assert damage claims.

Pos: 14.2 /Dokumentation allgemein/Gliederungselemente/---Seitenwechsel--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

6 Notes about this Documentation WAGO-I/O-SYSTEM 750

753-530 8DO 24V DC 0.5A

Manual

Version 1.1.0

Pos: 14.3 /All e Seri en ( All ge meine Mo dul e)/Ü bers chr ift en f ür alle S erie n/Hi nwei se z ur Dok um enta tio n/S ymbol e - Ü bers chr ift 2 @ 1 3\mod_1351068042408_21.docx @ 105270 @ 2 @ 1

1.3 Symbols

Pos: 14 .4.1 /Al le Seri en ( All ge mei ne Mo dul e)/ Wic htig e Er lä uter ung en/ Sich erh eits- und sonstige Hinweise/Gefahr/Gefahr: _Warnung vor Personenschäden allgemein_ - Erl äuter ung @ 13\ mod_1343309450020_21.docx @ 101029 @ @ 1

Personal Injury!

Indicates a high-risk, imminently hazardous situation which, if not avoided, will

result in death or serious injury.

Pos: 14 .4.2 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äuter unge n/Sich erheit s- und sonsti ge Hinw eise/ Gefa hr/Gef ahr: _ Warnu ng vor Per son enschä den durc h elek trisc hen Str om_ - Erläuterung @ 13\mod_1343309694914_21.docx @ 101030 @ @ 1

Personal Injury Caused by Electric Current!

Indicates a high-risk, imminently hazardous situation which, if not avoided, will

result in death or serious injury.

Pos: 14 .4.3 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äuter unge n/Sich erheit s- und sonstige Hinweis e/W arn ung/ Warn ung: _ Warn ung vor P erso nensc h äde n allg em ei n_ - Erläuterung @ 13\mod_1343309877041_21.docx @ 101035 @ @ 1

Personal Injury!

Indicates a moderate-risk, potentially hazardous situation which, if not avoided,

could result in death or serious injury.

Pos: 14 .4.4 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äuter unge n/Sich erheit s- und so nsti ge H inw eis e/V orsic ht /Vor sich t: _War nung vor Person ensc häden al lge mein_ - Erläuterung @ 13\mod_1343310028762_21.docx @ 101038 @ @ 1

Personal Injury!

Indicates a low-risk, potentially hazardous situation which, if not avoided, may

result in minor or moderate injury.

Pos: 14 .4.5 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äuter unge n/Sich erheit s- und sonstige Hinweise/Achtung/Achtung: _Warnung vor Sachschäden allgemein_ - Erläuterung @ 13\mod_1343310134623_21.docx @ 101041 @ @ 1

Damage to Property!

Indicates a potentially hazardous situation which, if not avoided, may result in

damage to property.

Pos: 14 .4.6 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äuter unge n/Sich erheit s- und so nsti ge H inw eis e/A chtu ng/ Ach tung : _ War nung v or Sac hsc hä den dur ch ele ktros tati sc he Aufl adu ng_ - Erläuterung @ 13\mod_1343310227702_21.docx @ 101044 @ @ 1

Damage to Property Caused by Electrostatic Discharge (ESD)!

Indicates a potentially hazardous situation which, if not avoided, may result in

damage to property.

Pos: 14 .4.7 /Al le Seri en (All gemei ne Mod ule) /Wi chti ge Erl äut eru nge n/Si cher heit s- u nd sonstige Hinweise/Hinweis/Hinweis: _Wichtiger Hinweis allgemein_ - Erläuterung @ 13\mod_1343310326906_21.docx @ 101047 @ @ 1

Important Note!

Indicates a potential malfunction which, if not avoided, however, will not result in

damage to property.

Pos: 14 .4.8 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äuter unge n/Sich erheit s- und so nsti ge H inw eis e/I nfor mat ion/ Inf or matio n: _W eiter e Inf or mati on allg emei n_ - Erl äuter ung @ 13 \mod_1343310439814_21.docx @ 101051 @ @ 1

WAGO-I/O-SYSTEM 750 Notes about this Documentation 7

753-530 8DO 24V DC 0.5A

Manual

Version 1.1.0

Additional Information:

Refers to additional information which is not an integral part of this

documentation (e.g., the Internet).

Pos: 14.5 /Dokumentation all ge mein/ Glie der ungs ele mente /---Seit en wechs el--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

8 Notes about this Documentation WAGO-I/O-SYSTEM 750

753-530 8DO 24V DC 0.5A

Manual

Version 1.1.0

Pos: 14 .6 /All e Seri en (Allg emeine Modul e)/Hi nweis e zur Do kument ation /Zahl ensy steme @ 3\ mod_1221059454015_21.docx @ 21711 @ 2 @ 1

1.4 Number Notation

Table 2: Number Notation

Number Code

Example

Note

Decimal

100

Normal notation

Hexadecimal

0x64

C notation

Binary

'100'

'0110.0100'

In quotation marks, nibble separated with

dots (.)

Pos: 14.7 /All e Seri en ( All ge meine Mo dul e)/H in weis e zur Dokumentation/Schriftkonventionen @ 3\mod_1221059521437_21.docx @ 21714 @ 2 @ 1

1.5 Font Conventions

Table 3: Font Conventions

Font Type

Indicates

italic

Names of paths and data files are marked in italic-type.

e.g.: C:\Program Files\WAGO Software

Menu

Menu items are marked in bold letters.

e.g.: Save

>

A greater-than sign between two names means the selection of a

menu item from a menu.

e.g.: File > New

Input

Designation of input or optional fields are marked in bold letters,

e.g.: Start of measurement range

“Value”

Input or selective values are marked in inverted commas.

e.g.: Enter the value “4 mA” under Start of measurement range.

[Button]

Pushbuttons in dialog boxes are marked with bold letters in square

brackets.

e.g.: [Input]

[Key]

Keys are marked with bold letters in square brackets.

e.g.: [F5]

Pos: 15 /Doku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Important Notes 9

753-530 8DO 24V DC 0.5A

Manual

Version 1.1.0

Pos: 16 /A ll e Ser ien (Al lg emei ne M od ule)/ Üb ers chrif te n für al le Seri en/Wi chtig e Erläut erung en/ Wichti ge Erlä uteru ngen - Üb ersc hrift 1 @ 4\ mod_1241428899156_21.docx @ 32170 @ 1 @ 1

2 Important Notes

Pos: 17.1 /All e Seri en ( All ge meine Do kum ente) ( All ge meine Mo dule) /Wi cht ige Erl äut eru nge n/Ei nl eit ung Wic htige Erl äut eru nge n @ 3 \mod_1221059818031_21.docx @ 21717 @ @ 1

This section includes an overall summary of the most important safety

requirements and notes that are mentioned in each individual section. To protect

your health and prevent damage to devices as well, it is imperative to read and

carefully follow the safety guidelines.

Pos: 17.2 /All e Seri en ( All ge meine Mo dul e)/Ü bers chr ift en f ür alle S erie n/Wi chti ge Erl äuter u ngenR ec htlic he Gr undl ag en - Üb ersc hrift 2 @ 3\ mod_1221060626343_21.docx @ 21726 @ 2 @ 1

2.1 Legal Bases

Pos: 17.3 /Alle Serien (Allgemeine Dokumente) (Allgemeine Module)/Wichtige Erläuterungen/Änderungsvorbehalt - Übers chri ft 3 un d I nhalt @ 3\mod_1221060036484_21.docx @ 21720 @ 3 @ 1

2.1.1 Subject to Changes

WAGO Kontakttechnik GmbH & Co. KG reserves the right to provide for any

alterations or modifications that serve to increase the efficiency of technical

progress. WAGO Kontakttechnik GmbH & Co. KG owns all rights arising from

the granting of patents or from the legal protection of utility patents. Third-party

products are always mentioned without any reference to patent rights. Thus, the

existence of such rights cannot be excluded.

Pos: 17.4 /Serie 750 (WAGO-I/O-SYST EM)/ Wic htige Erl äuter unge n/Pers onalq uali fikati onPer sonal qual ifika tion 750- xxxx - Ü bersc hri ft 3 und Inhalt @ 3\mod_1224061208046_21.docx @ 24063 @ 3 @ 1

2.1.2 Personnel Qualifications

All sequences implemented on WAGO-I/O-SYSTEM 750 devices may only be

carried out by electrical specialists with sufficient knowledge in automation. The

specialists must be familiar with the current norms and guidelines for the devices

and automated environments.

All changes to the coupler or controller should always be carried out by qualified

personnel with sufficient skills in PLC programming.

Pos: 17.5 /Serie 750 (WAGO-I/O-SYSTEM)/Wichtige Erläuterungen/Bestimmungsgemäße VerwendungBestimmungsgemäße Verwendung 750-xxxx - Über schr if t 3 und I nhal t @ 3\ mod_1224064151234_21.docx @ 24070 @ 3 @ 1

2.1.3 Use of the WAGO-I/O-SYSTEM 750 in Compliance with

Underlying Provisions

Fieldbus couplers, fieldbus controllers and I/O modules found in the modular

WAGO-I/O-SYSTEM 750 receive digital and analog signals from sensors and

transmit them to actuators or higher-level control systems. Using programmable

controllers, the signals can also be (pre-) processed.

The devices have been developed for use in an environment that meets the IP20

protection class criteria. Protection against finger injury and solid impurities up to

12.5 mm diameter is assured; protection against water damage is not ensured.

Unless otherwise specified, operation of the devices in wet and dusty

environments is prohibited.

Operating the WAGO-I/O-SYSTEM 750 devices in home applications without

further measures is only permitted if they meet the emission limits (emissions of

interference) according to EN 61000-6-3. You will find the relevant information

in the section “Device Description” > “Standards and Guidelines” in the manual

for the used fieldbus coupler/controller.

10 Important Notes WAGO-I/O-SYSTEM 750

753-530 8DO 24V DC 0.5A

Manual

Version 1.1.0

Appropriate housing (per 94/9/EG) is required when operating the WAGO-I/O-

SYSTEM 750 in hazardous environments. Please note that a prototype test

certificate must be obtained that confirms the correct installation of the system in

a housing or switch cabinet.

Pos: 17.6 /All e Seri en ( All ge meine Do kum ente) ( All ge meine Mo dule) /Wi cht ige Erl äut eru nge n/T echni sc her Zus tan d d er G erä te - Ü bersc hrift 3 un d Inhal t @ 3\mod_1221060446109_21.docx @ 21723 @ 3 @ 1

2.1.4 Technical Condition of Specified Devices

The devices to be supplied ex works are equipped with hardware and software

configurations, which meet the individual application requirements. WAGO

Kontakttechnik GmbH & Co. KG will be exempted from any liability in case of

changes in hardware or software as well as to non-compliant usage of devices.

Please send your request for modified and new hardware or software

configurations directly to WAGO Kontakttechnik GmbH & Co. KG.

Pos: 17.7 /Dokumentation all ge mein/ Glie der ungs ele mente /---Seit en wechs el--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Important Notes 11

753-530 8DO 24V DC 0.5A

Manual

Version 1.1.0

Pos: 17 .8 /All e Seri en (Allg emeine Modul e)/Ü berschr ifte n für alle S erie n/Wich tige Er läuter ung enSic herhei tshi nweis e - Übers chrif t 2 @ 6\mod_1260180299987_21.docx @ 4672 4 @ 2 @ 1

2.2 Safety Advice (Precautions)

Pos: 17.9 /All e Seri en ( All ge meine Do kum ente) ( All ge meine Mo dule) /Wi cht ige Erl äut eru nge n/Si cher hei ts hin weis e/Ei nl eitu ng Sich erh eitshi nweis e Hard ware @ 6\mod_1260180170493_21.docx @ 46720 @ @ 1

For installing and operating purposes of the relevant device to your system the

following safety precautions shall be observed:

Pos: 17.1 0. 1 /Al le S eri en ( Allg em ein e Do ku ment e) (Al lg em eine M o dul e)/ Wich tig e Erl äuter u ngen /Sic h erhei ts hinw eise /G efahr /G efahr : N ich t an G erät en un ter Spa nnung arbeite n! @ 6\mod_1260180365327_21.docx @ 46727 @ @ 1

Do not work on devices while energized!

All power sources to the device shall be switched off prior to performing any

installation, repair or maintenance work.

Pos: 17 .10. 2 /Serie 75 0 (WAG O-I/O- SYST EM) /Wic htig e Er l äuter ung en /Sic her hei ts- un d s onsti ge H in wei se/G ef ahr/ Gefa hr: Ei nbau 07 50- xxxx nur in Geh äusen, S chrä nken oder ele ktrisc hen Betr iebsr äume n! @ 6\mod_1260180556692_21.docx @ 46731 @ @ 1

Install the device only in appropriate housings, cabinets or in electrical

operation rooms!

The WAGO-I/O-SYSTEM 750 and its components are an open system. As such,

install the system and its components exclusively in appropriate housings,

cabinets or in electrical operation rooms. Allow access to such equipment and

fixtures to authorized, qualified staff only by means of specific keys or tools.

Pos: 17.1 0. 3 /Al le S eri en ( Allg em ein e Do ku ment e) (Al lg em eine M o dul e)/ Wich tig e Erl äuter u ngen /Sic h erhei ts hinw eise /G efahr /G efahr : U nfal l verh ütung sv orsc hri ften beachten! @ 6\mod_1260180657000_21.docx @ 46735 @ @ 1

Pos: 17.1 0. 4 /Al le S eri en ( Allg em ein e Do ku ment e) (Al lg em eine M o dul e)/ Wich tig e Erl äuter u ngen /Sic h erhei ts hinw eise /G efahr /G efahr : A uf normg er echt e n Ansc hlu ss ac hten! @ 6 \mod_1260180753479_21.docx @ 46739 @ @ 1

Pos: 17.1 1. 1 /Al le S eri en ( Allg em ein e Do ku ment e) (Al lg em eine M o dul e)/ Wich tig e Erl äuter u ngen /Sic h erhei ts hinw eise /Ac htu ng/A cht ung : Defek te oder besch ädigt e Gerät e austaus chen! @ 6\mod_1260180857358_21.docx @ 46743 @ @ 1

Replace defective or damaged devices!

Replace defective or damaged device/module (e.g., in the event of deformed

contacts), since the long-term functionality of device/module involved can no

longer be ensured.

Pos: 17.1 1. 2 /Al le S eri en ( Allg em ein e Do ku ment e) (Al lg em eine M o dul e)/ Wich tig e Erl äuter u ngen /Sic h erhei ts hinw eise /Ac htu ng/A cht ung : G erät e vor kriec hen den und i sol ier e nden Sto ffen s chütz en! @ 6\mod_1260181036216_21.docx @ 46747 @ @ 1

Protect the components against materials having seeping and insulating

properties!

The components are not resistant to materials having seeping and insulating

properties such as: aerosols, silicones and triglycerides (found in some hand

creams). If you cannot exclude that such materials will appear in the component

environment, then install the components in an enclosure being resistant to the

above-mentioned materials. Clean tools and materials are imperative for handling

devices/modules.

Pos: 17.1 1. 3 /Al le S eri en ( Allg em ein e Do ku ment e) (Al lg em eine M o dul e)/ Wich tig e Erl äuter u ngen /Sic h erhei ts hinw eise /Ac htu ng/A cht ung : Rei nig ung nur mi t zul äss ig en M at erial ien! @ 6\mod_1260181203293_21.docx @ 46751 @ @ 1

Clean only with permitted materials!

Clean soiled contacts using oil-free compressed air or with ethyl alcohol and

leather cloths.

Pos: 17.1 1. 4 /Al le S eri en ( Allg em ein e Do ku ment e) (Al lg em eine M o dul e)/ Wich tig e Erl äuter u ngen /Sic h erhei ts hinw eise /Ac htu ng/A cht ung : K ein K ont a ktspra y verw end en! @ 6\ mod_1260181290808_21.docx @ 46755 @ @ 1

12 Important Notes WAGO-I/O-SYSTEM 750

753-530 8DO 24V DC 0.5A

Manual

Version 1.1.0

Do not use any contact spray!

Do not use any contact spray. The spray may impair contact area functionality in

connection with contamination.

Pos: 17.1 1. 5 /Al le S eri en ( Allg em ein e Do ku ment e) (Al lg em eine M o dul e)/ Wich tig e Erl äuter u ngen /Sic h erhei ts hinw eise /Ac htu ng/A cht ung : V erpol ung ver mei de n! @ 6\mod_1260184045744_21.docx @ 46767 @ @ 1

Do not reverse the polarity of connection lines!

Avoid reverse polarity of data and power supply lines, as this may damage the

devices involved.

Pos: 17.1 1. 6 /Al le S eri en ( Allg em ein e Do ku ment e) (Al lg em eine M o dul e)/ Wichti ge Erlä uteru ngen/Si ch erheits hinw eise/A chtu ng/Ac htung : Elektr ostat isch e Entla dung v ermeid en! @ 6\mod_1260181364729_21.docx @ 46759 @ @ 1

Avoid electrostatic discharge!

The devices are equipped with electronic components that may be destroyed by

electrostatic discharge when touched. Please observe the safety precautions

against electrostatic discharge per DIN EN 61340-5-1/-3. When handling the

devices, please ensure that environmental factors (personnel, work space and

packaging) are properly grounded.

Pos: 18 /Doku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Device Description 13

753-530 8DO 24V DC 0.5A

Manual

Version 1.1.0

Pos: 19 /A ll e Ser ien (Al lg emei ne M od ule)/ Üb ers chrif te n für al le S eri en/G erä teb esc hrei bu ng/G erä tebe schr eib ung - Üb ersc hrift 1 @ 3\mod_1233756084656_21.docx @ 27096 @ 1 @ 1

3 Device Description

Pos: 20 /S eri e 7 50 ( WA GO-I/ O-SYST EM)/ Gerät ebesc hrei bung/Ei nlei tung /Anw endung /DO/ Anwen dung 7 50-x5xx DO @ 3\mod_1233764594468_21.docx @ 27120 @ @ 1

The 753-530 (8DO 24V DC 0.5A) Digital Output Module transmits binary control

signals from the automation device to the connected actuators (e.g., solenoid

valves, contactors, transmitters, relays or other electrical loads).

Pos: 21 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /Ger ät ebesc hrei bu ng/Ei nlei tu ng/I/ O-B eschr eibu ng/D O/I /O-B eschr eibu ng 750-05xx 8 DO 1-Leit er (D O 1 ... DO 8) @ 4\ mod_1235647050031_21.docx @ 27858 @ @ 1

The module has eight output channels. Eight 1-conductor actuators may be

directly connected to the module. The actuators can be connected using

connection DO 1 … DO 8.

Pos: 22 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /Ger ät ebesc hrei bu ng/Ei nlei tu ng/I/ O-B eschr ei bung /Al lg emei n/Ver w eis a uf K api tel "A nschl üss e" @ 8\ mod_1276775378035_21.docx @ 57956 @ @ 1

The assignment of the connections is described in the “Connectors” section.

Pos: 23 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /Ger ät ebesc hrei bu ng/Ei nlei tu ng/I/ O-B eschr ei bung /Al lg emei n/Ver w eis a uf K api tel "G erät e a nsc hließ en" > "A nsc hlus sb eis piel( e)" @ 5\ mod_1246015203281_21.docx @ 36298 @ @ 1

Connection examples are shown in section “Connecting Devices” > … >

“Connection Example(s)”.

Pos: 24 /S eri e 7 50 ( WA GO-I/ O-SYST EM)/ Wicht ige Erl äuter unge n/Sich erhei ts- und sonstige Hinweise/Achtung/Achtung: DO Induktionsspannungsbegrenzung Elektronik @ 3\mod_1233815757507_21.docx @ 27153 @ @ 1

Limit all induced voltage!

The electronic components of the I/O module can be damaged by the induced

voltage produced when inductive loads are de-activated.

An appropriate protection circuit, e.g., a recovery diode, must be installed in

parallel to the load to limit this induced voltage.

Pos: 25 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /Ger ät ebesc hrei bu ng/Ei nlei tu ng/I/ O-B eschr eibu ng/D O/I /O-B eschr eibu ng 750-05 xx DO kurzsc hlussfest @ 3\mod_1233817429086_21.docx @ 27167 @ @ 1

The output channels are electrically short-circuit-protected.

Pos: 26 /Serie 750 (WAGO-I/O-SYST EM )/G erät ebes chr eibu ng/Ei nlei tu ng/I/ O-B esc hrei bung /DO /I/O- Besc hrei bung 75 0-x5xx D O H SS / pos i tivsc hal te nd ( 24 V) @ 3\mod_1233816955742_21.docx @ 27160 @ @ 1

The I/O module outputs provide high-side switching. If the signal status of an

output channel is at “high” the 24 V potential for field power will be switched to

the appropriate output connection.

Pos: 27 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /Ger ät ebesc hrei bu ng/Ei nlei tu ng/I/ O-B eschr eibu ng/D O/I /O-B eschr eibu ng 750-05xx Leistungskontakt durch Einspeiseklemme @ 5\mod_1246856959993_21.docx @ 36590 @ @ 1

The supply voltage for the field side is derived from an adjacent supply module by

means of power jumper contacts.

Pos: 28 /S eri e 7 50 ( WA GO-I/ O-SYST EM)/ Wicht ige Erl äuter unge n/Sich erhei ts- u nd so nstig e H in weis e/ Acht ung /Ach tu ng: D O Ü berl ast sch utz - Ei npeise klem me mit Sic herung @ 3\mod_1233814881117_21.docx @ 27150 @ @ 1

Provide for overload protection!

Overloading can damage the electronic components of the I/O module.

A fused supply module (750-601) must be installed upstream of the I/O module to

protect it against overloading!

Pos: 29 /S eri e 7 50 ( WA GO-I/ O-SYST EM)/ Ger äteb esc hrei bung /Ei nlei tung /LED -Anz eig e/LE D Z ust and Sig nal @ 3\ mod_1233755258578_21.docx @ 27087 @ @ 1

A green LED indicates the switched status of each channel.

Pos: 30 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /Ger ät ebesc hrei bu ng/Ei nlei tu ng/L ED-A nzei ge/ Verw eis auf Kapit el " Anz eig eel em ente" @ 5\mod_1246010525000_21.docx @ 36194 @ @ 1

The meaning of the LEDs is described in the “Display Elements” section.

Pos: 31 /S eri e 7 50 ( WA GO-I/ O-SYST EM)/ Gerät ebesc hrei bung/Ei nlei tung /Vers orgung /Vers orgu ng 24 V, 0 V üb er Leis tung sk onta kte Sta ndar d u nd Vari ant en @ 20\ mod_1410359516385_21.docx @ 163106 @ @ 1

The I/O module 753-530 (8DO 24V DC 0.5A) and their variants receives the

24 V voltage supply for the field level from an upstream I/O module or from the

fieldbus coupler/controller via blade-formed power jumper contacts. It then

provides these potentials to subsequent I/O modules via spring-formed power

jumper contacts.

Pos: 32 /S eri e 7 50 ( WA GO-I/ O-SYST EM)/ Wichtig e Erläut eru ngen/ Sic herh eits- und sonstige Hinweise/Achtung/Achtung: Maximaler Strom Leistungskontakte 10 A @ 3\mod_1226499143500_21.docx @ 25029 @ @ 1

14 Device Description WAGO-I/O-SYSTEM 750

753-530 8DO 24V DC 0.5A

Manual

Version 1.1.0

Do not exceed maximum current via power jumper contacts!

The maximum current to flow through the power jumper contacts is 10 A.

Greater currents can damage the contacts.

When configuring your system, ensure that this current is not exceeded. If

exceeded, insert an additional supply module.

Pos: 33 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /Ger ät ebesc hrei bu ng/Ei nlei tu ng/V ers orgung / Galv ani sche T r enn ung F el d/Sy ste m @ 3\mod_1233756478750_21.docx @ 27102 @ @ 1

The field voltage and the system voltage are electrically isolated from each other.

Pos: 34 /S eri e 7 50 ( WA GO-I/ O-SYST EM)/ Wicht ige Erl äuter unge n/Sich erhei ts- u nd so nstig e H in weis e/ Warn ung/ W arnung : Eins atz Vari an te / xxx- 8xx i n si ch erh eitsg eri cht et en A nwen dung en @ 5\mod_1246882860453_21.docx @ 36680 @ @ 1

Using in safety related applications!

When using the I/O module ( 753-530 ) in safety-related applications, the

instructions and connection examples in Section “Using Interference-Free

Variants of I/O Modules in Safety Related Applications” are to be observed!

Pos: 35 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /Ger ät ebesc hrei bu ng/Ei nlei tu ng/V ers org ung/ Anor dn ung bei Eins atz i n s ic herh eits ger ic htet en A nwe ndu nge n bl ock weis e @ 5\mod_1246876694406_21.docx @ 36674 @ @ 1

Any configuration of the output modules is possible when designing the fieldbus

node. Grouping of module types is not necessary.

Pos: 36 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /G erät eb esc hrei bung /Ei nlei tu ng/Ei ns atz ber eich /Ei nsatz ber eic h 7 50- xxxx all e Koppl er/Co ntrol ler oh ne Einsc hrän kung @ 3\ mod_1232541691906_21.docx @ 26522 @ @ 1

The I/O module 753-530 can be used with all fieldbus couplers/controllers of the

WAGO-I/O-SYSTEM 750.

Pos: 37 /Doku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Device Description 15

753-530 8DO 24V DC 0.5A

Manual

Version 1.1.0

Pos: 38 /A ll e Ser ien (Al lg emei ne M od ule)/ Üb ers chrif te n für al le S eri en/G erät ebes chr eibu ng/A nsic ht - Ü ber schr if t 2 @ 4\ mod_1240984217343_21.docx @ 31958 @ 2 @ 1

3.1 View

Pos: 39 /S eri e 7 53 ( WA GO-I/ O-SYST EM) /Hi n weis e zur D okum ent ati on/Hi nw eis z u m Zub ehör tei l 75 3-110 @ 20\mod_1411023611789_21.docx @ 163868 @ @ 1

Depiction of the I/O module with 753-110 Connector!

Information on this pluggable connection pertains to the 753-110 Connector,

which is not included with the I/O module.

Pos: 40 /S eri e 7 53 ( WA GO-I/ O-SYST EM) /Ger ät ebesc hrei bu ng/A nsic ht/D ig itala usga ngs klem me n/Ansi cht 7 53-0 530 @ 21\mod_1417082691550_21.docx @ 169358 @ @ 1

Figure 1: View

Pos: 41 /S eri e 7 53 ( WA GO-I/ O-SYST EM) /Ger ät ebesc hrei bu ng/A nsic ht/A nsic ht – Leg ende mit L eist ungsk ontakt en_ mit Kodi erung , Kabel befest igung und Prüf öffn ungen @ 20 \mod_1411031302199_21.docx @ 163871 @ @ 1

Table 4: Legend for Figure “View”

Pos.

Description

Details See Section

1

Marking possibility with Mini-

WSB

---

2

Status-LEDs

“Device Description” > “Display

Elements”

3

Data contacts

“Device Description” > “Connectors”

4

CAGE CLAMP

®

connectors

“Device Description” > “Connectors”

5

Release tab

“Mounting” > “Inserting and Removing

Devices” and “I/O Modules with

Pluggable Wiring Level (Series 753)”

6

Coding possibility with coding

fingers

“Mounting” > “Coding”

7

Power jumper contacts

“Device Description” > “Connectors”

8

Test port

---

9

Fixing lug for cable ties

“Mounting” > “I/O Modules with

Pluggable Wiring Level (Series 753)”

Pos: 42 /D o kume nt ation all ge mein/ Glie der ungs ele mente /---Seit en wechs el--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

16 Device Description WAGO-I/O-SYSTEM 750

753-530 8DO 24V DC 0.5A

Manual

Version 1.1.0

Pos: 43 /A ll e Ser ien (Al lg emei ne M od ule)/ Üb ers chrif te n für al le S eri en/G erä teb esc hrei bu ng/A nsc hlüs se - Über schri ft 2 @ 4\mod_1240984262656_21.docx @ 31961 @ 2 @ 1

3.2 Connectors

Pos: 44 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /Ger ät ebesc hrei bu ng/A nsc hlüss e/D ate nko ntakt e/Kl em menbu s - Ü bersc hrift 3 @ 6\mod_1256294684083_21.docx @ 43660 @ 3 @ 1

3.2.1 Data Contacts/Internal Bus

Pos: 45.1 /Serie 750 (WAGO-I/O-SYST EM)/ Ger äteb eschr ei bung/ Ansc hl üsse /Date nk onta kte - F eld bus kop pler/-c on troll er , Ab bil dung u nd B esc hrei bung @ 3 \mod_1231771259187_21.docx @ 26002 @ @ 1

Communication between the fieldbus coupler/controller and the I/O modules as

well as the system supply of the I/O modules is carried out via the internal bus. It

is comprised of 6 data contacts, which are available as self-cleaning gold spring

contacts.

Figure 2: Data Contacts

Pos: 45.2 /Serie 750 (WAGO-I/O-SYST EM)/ Wic htige Erl äuter unge n/Sic herhei ts- u nd so nsti g e Hin weis e/ Acht ung /Ach tu ng: Buskl e mmen nic ht auf Gol dfe der konta kt e leg en! @ 7 \mod_1266318463636_21.docx @ 50695 @ @ 1

Do not place the I/O modules on the gold spring contacts!

Do not place the I/O modules on the gold spring contacts in order to avoid soiling

or scratching!

Pos: 45.3 /Serie 750 (WAGO-I/O-SYST EM)/ Wic htige Erl äuter unge n/Sic herhei ts- und sonstige Hinweise/Achtung/Achtung: ESD - Auf gut e E rdung der U mg ebu ng ac hte n! @ 7\ mod_1266318538667_21.docx @ 50708 @ @ 1

Ensure that the environment is well grounded!

The devices are equipped with electronic components that may be destroyed by

electrostatic discharge. When handling the devices, ensure that the environment

(persons, workplace and packing) is well grounded. Avoid touching conductive

components, e.g. data contacts.

Pos: 46 /Doku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Device Description 17

753-530 8DO 24V DC 0.5A

Manual

Version 1.1.0

Pos: 47 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /Ger ät ebesc hrei bu ng/A nsc hlüss e/L eist ung skont akt e/F eld vers orgu ng - Üb ersc hrift 3 @ 6\ mod_1256294692864_21.docx @ 43664 @ 3 @ 1

3.2.2 Power Jumper Contacts/Field Supply

Pos: 48 .1 /Serie 750 (WAGO-I/O-S YSTEM) /Wic htige Er läut erung en/Si cherh eits- und s onsti g e Hin wei se/ Vors ic ht/V ors ich t: Ver l etz ungsg efa hr durc h s char fk antig e M ess er kont akte! @ 6\mod_1256193279401_21.docx @ 43414 @ @ 1

Risk of injury due to sharp-edged blade contacts!

The blade contacts are sharp-edged. Handle the I/O module carefully to prevent

injury.

Pos: 48.2 /Serie 750 (WAGO-I/O-SYST EM )/ Ger äteb esc hrei bung /Ans chl üs se/L eist u ngs kont akte 2 LK (M ess er/ Leis tung s konta kte 2 L K (M ess er/ Fed er) - Ei nleitung @ 15\mod_1371721641099_21.docx @ 123714 @ @ 1

The I/O module 753-530 has 2 self-cleaning power jumper contacts that supply

and transmit power for the field side. The contacts on the left side of the I/O

module are designed as blade contacts and those on the right side as spring

contacts.

Pos: 48.3 /Serie 753 (WAGO-I/O-SYST EM )/ Ger äteb esc hrei bung /Ans chl üs se/L eist u ngs kont akte 2 LK (M ess er/ Leis tung s konta kte /Fel dv ersor gu ng 2 LK ( M ess er/Fe der ) - Abbildung @ 17\mod_1381924880242_21.docx @ 134239 @ @ 1

Figure 3: Power Jumper Contacts

Pos: 48.4 /Serie 750 (WAGO-I/O-SYST EM )/ Ger äteb esc hrei bung /Ans chl üs se/L eist u ngs kont akte 2 LK (M ess er/ Leis tung s konta kte 2 L K (M ess er/ Fed er) - Leg ende @ 15 \mod_1371721352500_21.docx @ 123710 @ @ 1

Table 5: Legend for Figure “Power Jumper Contacts”

Contact

Type

Function

1

Spring contact

Potential transmission (U

v

) for field supply

2

Spring contact

Potential transmission (0 V) for field supply

3

Blade contact

Potential feed-in (0 V) for field supply

4

Blade contact

Potential feed-in (U

v

) for field supply

Pos: 48.5 /Serie 750 (WAGO-I/O-SYST EM)/ Wic htige Erl äuter unge n/Sic herhei ts- u nd so nsti g e Hin weis e/ Acht ung /Ach tu ng: M a ximal er S tro m L eist ungs kon tak te 10 A @ 3\mod_1226499143500_21.docx @ 25029 @ @ 1

Do not exceed maximum current via power jumper contacts!

The maximum current to flow through the power jumper contacts is 10 A.

Greater currents can damage the contacts.

When configuring your system, ensure that this current is not exceeded. If

exceeded, insert an additional supply module.

Pos: 48.6 /Serie 750 (WAGO-I/O-SYST EM)/ Wic htige Erl äuter unge n/Sic herhei ts- u nd sonsti ge Hin weis e/Hinw eis/Hi nwei s: Pote ntial eins peise klemme f ür Erde ei nset zen! ( keine LK f ür Erde) @ 3\mod_1226499037468_21.docx @ 25023 @ @ 1

18 Device Description WAGO-I/O-SYSTEM 750

753-530 8DO 24V DC 0.5A

Manual

Version 1.1.0

Use supply modules for ground (earth)!

The I/O module has no power jumper contacts for receiving and transmitting the

earth potential. Use a supply module when an earth potential is needed for the

subsequent I/O modules.

Pos: 49 /Doku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Device Description 19

753-530 8DO 24V DC 0.5A

Manual

Version 1.1.0

Pos: 50 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /Ger ät ebesc hrei bu ng/A nsc hlüss e/C AGE CLAMP-Anschl üss e - Ü ber schri ft 3 @ 6\mod_1256296337770_21.docx @ 43674 @ 3 @ 1

3.2.3 CAGE CLAMP

®

Connectors

Pos: 51 /S eri e 7 53 ( WA GO-I/ O-SYST EM) /Hi n weis e zur D okum ent ati on/Hi nw eis z u m Zub ehör tei l 75 3-110 @ 20\mod_1411023611789_21.docx @ 163868 @ @ 1

Depiction of the I/O module with 753-110 Connector!

Information on this pluggable connection pertains to the 753-110 Connector,

which is not included with the I/O module.

Pos: 52 /S eri e 7 53 ( WA GO-I/ O-SYST EM) /Ger ät ebesc hrei bu ng/A nsc hlüss e/D igi talaus g angs kle mmen/A nschl üsse 75 3-053 x 8 DO 1-Lei ter, 2 LKs @ 21\mod_1417086116167_21.docx @ 169387 @ @ 1

Figure 4: CAGE CLAMP

®

Connectors

Table 6: Legend for Figure “CAGE CLAMP

®

Connectors”

Channel

Designation

Connector

Function

1

DO 1

1

Output DO 1: signal voltage

2

DO 2

5

Output DO 2: signal voltage

3

DO 3

2

Output DO 3: signal voltage

4

DO 4

6

Output DO 4: signal voltage

5

DO 5

3

Output DO 5: signal voltage

6

DO 6

7

Output DO 6: signal voltage

7

DO 7

4

Output DO 7: signal voltage

8

DO 8

8

Output DO 8: signal voltage

Pos: 53 /Doku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\ mod_1221108045078_0.docx @ 21810 @ @ 1

20 Device Description WAGO-I/O-SYSTEM 750

753-530 8DO 24V DC 0.5A

Manual

Version 1.1.0

Pos: 54 /A ll e Ser ien (Al lg emei ne M od ule)/ Üb ers chrif te n für al le S eri en/G erä teb esc hrei bu ng/A nzei geel e ment e - Ü bersc hrift 2 @ 4\ mod_1240984390875_21.docx @ 31964 @ 2 @ 1

3.3 Display Elements

Pos: 55 /S eri e 7 50 ( WA GO-I/ O-SYSTEM)/Gerätebeschreibung/Anzeigeelemente/Digitalausgangsklemmen/Anzeigeelemente 750-05x x 8 DO @ 11\mod_1322218413230_21.docx @ 83738 @ @ 1

Figure 5: Display Elements

Pos: 56 /D o kume nt ation all ge mein/ Glie der ungs ele mente /---Seit en wechs el--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

Table 7: Legend for Figure “Display Elements”

Channel

Designation

LED

State

Function

1 Status DO 1 A

Off

Output DO 1: not controlled

Green

Output DO 1: controlled

2 Status DO 2 E

Off

Output DO 2: not controlled

Green

Output DO 2: controlled

3 Status DO 3 B

Off

Output DO 3: not controlled

Green

Output DO 3: controlled

4 Status DO 4 F

Off

Output DO 4: not controlled

Green

Output DO 4: controlled

5 Status DO 5 C

Off

Output DO 5: not controlled

Green

Output DO 5: controlled

6 Status DO 6 G

Off

Output DO 6: not controlled

Green

Output DO 6: controlled

7 Status DO 7 D

Off

Output DO 7: not controlled

Green

Output DO 7: controlled

8 Status DO 8 H

Off

Output DO 8: not controlled

Green

Output DO 8: controlled

Page is loading ...

WAGO 8-channel, 24VDC, 0.5A User manual

WAGO 8-channel, 24VDC, 0.5A User manual

Related papers

Other documents