Froling RBG 3200 Touch Operating Instructions Manual

Brand: Froling

Model: RBG 3200 Touch

Type: Operating Instructions Manual

Operating Instructions

Room console RBG 3200 Touch

Translation of the original German operating instructions for the operator

Read and follow the instructions and safety information!

Technical changes, typographical errors and omissions reserved!

B0780115_en | Edition 08/06/2015

Froling GesmbH | A-4710 Grieskirchen, Industriestraße 12 | www.froeling.com

Table of contents

1 General 4

1.1 About these instructions 4

1.2 Safety information 4

2 Installation 5

2.1 Initial start-up 5

2.1.1 Connecting the bus cable 5

2.1.2 Setting end jumpers 6

2.1.3 Calibrate the display 6

2.1.4 Setting the module address 6

3 Overview of the basic functions 8

3.1 Visual display 8

3.1.1 Status LED 8

3.1.2 Icons 9

4 Operation 10

4.1 Navigation within the info menu 10

4.2 Navigation within the system menu 10

4.2.1 Navigating the menus 10

4.3 Adjusting parameters 12

4.4 Setting times 13

4.5 Setting the room temperature setpoints 15

4.6 Set the heating circuit mode 15

4.6.1 “OFF” mode 16

4.6.2 “Auto” mode 16

4.6.3 “Party” mode 16

4.6.4 “Setback” mode 16

5 Menu overview and parameters 17

5.1 Heating 17

5.1.1 Heating - Status 17

5.1.2 Heating - Temperatures 18

5.1.3 Heating - Times 19

5.2 Water 20

5.2.1 Water - Status 20

5.2.2 Water - Temperatures 21

5.2.3 Water - Times 21

5.3 Solar 22

5.3.1 Solar - Status 22

5.3.2 Solar - Temperatures 24

5.3.3 Solar - Heat meter 25

5.4 Buffer tank 26

5.4.1 Buffer tank - Status 26

5.4.2 Buffer tank - Temperatures 27

5.4.3 Buffer tank - Times 27

5.5 Boiler 2 28

Table of contents

2 Froling GesmbH | A-4710 Grieskirchen, Industriestraße 12 | www.froeling.com

5.5.1 Boiler 2 - Status 28

5.5.2 Boiler 2 - Temperatures 29

5.6 Difference regulator 30

5.6.1 Difference regulator - Status 30

5.7 Circulation pump 31

5.7.1 Circulation pump - Status 31

5.7.2 Circulation pump - Temperatures 31

5.7.3 Circulation pump - Times 31

5.8 System 32

5.8.1 System - Current values 32

5.8.2 System - Display operating rights 33

Froling Connect

5.9 Diagnostics 34

5.9.1 Diagnostics - Error display 34

5.10 Display settings 34

5.10.1 Display settings - General 34

Network settings

5.10.2 Display settings - Date / Time 35

6 Troubleshooting 36

6.1 Procedure for fault messages 36

7 FAQ 38

7.1 Updating the software of the touch control 38

7.2 Calibrating the touchscreen 40

Table of contents

Operating Instructions RBG 3200 Touch | B0780115_en 3

1 General

1.1 About these instructions

These instructions contain information about the electrical connection, operation,

control parameters and troubleshooting for the RBG 3200 Touch room console. All

parameters, which are visible at the “customer” operator level, are shown. The

parameters actually displayed may vary depending on system configuration and

operating level.

The constant further development of our products means that there may be minor

differences from the pictures and content. If you discover any errors, please let us

know: [email protected].

Subject to technical change.

Froling's RBG 3200 Touch room console is a multifunctional device for convenient

operation of the boiler from your living room.

1.2 Safety information

DANGER

When working on electrical components:

Risk of electrocution!

When work is carried out on electrical components:

❒ Only have work carried out by a qualified electrician

❒ Observe the applicable standards and regulations

➥Work must not be carried out on electrical components by unauthorised

persons

1General

About these instructions

4 Froling GesmbH | A-4710 Grieskirchen, Industriestraße 12 | www.froeling.com

2 Installation

❒ Run the bus cable through the large grommet

❒ Fit the holding frame as shown at the desired position in the room using the

anchors and screws provided

➥The large grommet must be on the right!

➥It is recommended to install the device above a flush-mounted socket so that

there is plenty of space to stow away the bus cable.

2.1 Initial start-up

NOTICE

You should have the initial startup carried out by the authorised heating engineer

from Froling customer services.

2.1.1 Connecting the bus cable

For the bus connections between the individual modules, cable type

LIYCY paired 2x2x0.5 should be used. The connection to the 5-pin plugs should be

carried out according to the following diagram:

+UBUS

CANH

CANL

+UBUS

CANH

CANL

Braidedshield

White

Green

Yellow

Brown

Braidedshield

White

Green

Yellow

Brown

Installation 2

Initial start-up

Operating Instructions RBG 3200 Touch | B0780115_en 5

2.1.2 Setting end jumpers

To ensure that the bus system continues to work properly,

the end jumpers (J) need to be set.

❒ If there is an RBG 3200 Touch at the end of a bus

system, the end jumper at this module must be set. All

the previous ones, with the exception of that at the

core module, have to be deleted.

2.1.3 Calibrate the display

Once the power supply has been switched on for the first time, the RBG 3200 Touch

starts by calibrating the display. To calibrate the touchscreen, you much press five

points indicated by a crosshair in the order shown.

NOTICE

Inaccurate calibration

If you do not tap the indicated points accurately, the control may stop working

properly and a software update may be required.

2.1.4 Setting the module address

Once the display has been calibrated, the module address must be set. If it is the first

RBG 3200 Touch in the bus system, set module address 1. Number any others in

sequence.

NOTICE! Do not select an address of 0 as it leads to malfunctions with the RBG 3200

Touch!

2Installation

Initial start-up

6 Froling GesmbH | A-4710 Grieskirchen, Industriestraße 12 | www.froeling.com

Once you have set the module address, you will need to restart the boiler controller

(switch main switch on boiler off and on). All of the system information will then be

loaded into the RBG 3200 Touch. This process can be time-consuming.

The following screen appears after the RBG 3200 Touch’s first system start:

The basic screen displays only the external temperature as no components have been

assigned to the RBG 3200 Touch yet.

Installation 2

Initial start-up

Operating Instructions RBG 3200 Touch | B0780115_en 7

3 Overview of the basic functions

3.1 Visual display

Number Description

ADate and time display

BShows the current external temperature

CShows the current temperature at the allocated DHW tank. This field is hidden if

no DHW tank has been assigned.

DShows the current room temperature of the allocated heating circuit. This field is

hidden if no heating circuit has been assigned.

EDown arrow to decrease the desired temperature setpoint for the room

FShows the temperature setpoint for the room

GUp arrow to increase the desired temperature setpoint for the room

HInfo menu icon for viewing all system information

ISystem menu icon for opening the system settings All parameters can be

displayed/edited depending on the user level

JFavourites menu icon for viewing the available quick functions

KMode icon for setting the mode of the allocated heating circuit

3.1.1 Status LED

The status LED shows the operating status of the system:

▪GREEN flashing (interval: 5 sec OFF, 1 sec ON): Off / Boiler off

▪ GREEN constant: BOILER SWITCHED ON

▪ ORANGE flashing: WARNING

▪ RED flashing: FAULT

3Overview of the basic functions

Visual display

8 Froling GesmbH | A-4710 Grieskirchen, Industriestraße 12 | www.froeling.com

3.1.2 Icons

Home icon

Tapping the Home icon takes you back to the basic display from any menu.

Back icon

Takes you back up one menu level of the system menu. Can be used to return to the

basic display.

Info menu icon

To access all system information. The information is ordered in a circular buffer. The

right and left arrows are used to switch between the individual pages.

System menu icon

Opens the system settings. Depending on the operating level and system

configuration, the various menu items available are organised in a circular buffer

which can be navigated using the right and left arrow.

Quick menu icon

Opens the quick menu. Various functions are available depending on the user level,

system configuration and current status.

Pen icon

If a parameter has the pen symbol beside it, it means that the parameter can be

adjusted. If you open the parameter, either the numeric keypad or a list box for

changing the value of the parameter will appear.

Confirm icon

Confirms any values entered and activates parameters.

Cancel icon

Discards any values entered without saving and closes messages.

An “i” at the top left after selecting a parameter indicates additional information

available for this parameter. Pressing the Cancel icon takes you back to the selected

parameter.

Overview of the basic functions 3

Visual display

Operating Instructions RBG 3200 Touch | B0780115_en 9

4 Operation

4.1 Navigation within the info menu

The info menu displays all the information about the system. Use the right and left

arrows to go to the individual menu items for the relevant information. The next time

you open the info menu, the last page viewed will be displayed.

4.2 Navigation within the system menu

The system menu shows the menu items available depending on the user level and

the system configuration. Tap the icon to open the corresponding menu item. The

system menu is structured in a circular buffer, which can be navigated using the right

and left arrows. The next time you open the system menu, the last page viewed will be

displayed.

4.2.1 Navigating the menus

After you open a menu item, the corresponding status display with current values will

appear. If, for example, several heating circuits are installed, you can use the right and

left arrows to navigate to the desired heating circuit. You can open any other menu

items available in the same way.

4Operation

Navigation within the info menu

10 Froling GesmbH | A-4710 Grieskirchen, Industriestraße 12 | www.froeling.com

The individual menus are divided into tabs for quicker navigation.

❒Tap on the desired tab

➥The list of parameters for the selected area will appear

The parameter list shows three parameters. The up and down arrows can be used to

scroll through longer lists of parameters. If you have reached the start or end of the

parameter list, the relevant arrow symbol will become inactive.

Operation 4

Navigation within the system menu

Operating Instructions RBG 3200 Touch | B0780115_en 11

4.3 Adjusting parameters

A parameter can only be adjusted if there is a pen icon beside it. Depending on the

type of parameter, either the numeric keypad...

... or a list box will appear.

In both cases you need to tap the confirm icon to save the entry.

4Operation

Adjusting parameters

12 Froling GesmbH | A-4710 Grieskirchen, Industriestraße 12 | www.froeling.com

4.4 Setting times

The desired time window for the component can be set in the "Times" tab in the

individual menus of the heating components (heating circuits, DHW tanks etc.). The

structure of the time menu and the procedure for changing the times are always the

same.

❒Use the left or right arrow to navigate to the desired day of the week

❒ Tap the symbol under the day of the week

➥The edit window will appear

You can specify up to four time windows per component and day.

❒Tap the desired time window

❒The time window will open for editing

❒ Set the start and end time for the time window using the up and down arrows

❒ Save the time window setting by tapping on the confirm icon

Operation 4

Setting times

Operating Instructions RBG 3200 Touch | B0780115_en 13

To delete a time window, set the times so that the hour and minute displays are

replaced by two dashes.

If you want to apply the time window setting to another day in addition, you can do this

by activating the relevant day.

4Operation

Setting times

14 Froling GesmbH | A-4710 Grieskirchen, Industriestraße 12 | www.froeling.com

4.5 Setting the room temperature setpoints

The desired room temperature setpoint can be set in the lower left area of the basic

display:

❒Change the temperature in the room using the up and down arrows

NOTICE! The room temperature can only be changed in automatic mode (when the

heating circuit control is active) and in party mode!

4.6 Set the heating circuit mode

The current mode for the allocated heating circuit is displayed in the basic display to

the left of the mode icon.

Operation 4

Setting the room temperature setpoints

Operating Instructions RBG 3200 Touch | B0780115_en 15

Setting another mode:

❒Tap the mode icon

➥Mode-select is displayed

❒Tap the appropriate icon to change the heating circuit mode

The following modes are available:

4.6.1 “OFF” mode

The allocated heating circuit is switched off, the frost protection function remains

active.

4.6.2 “Auto” mode

The allocated heating circuit and the allocated DHW tank are controlled according to

the timed program settings.

4.6.3 “Party” mode

The allocated heating circuit is set to heating mode until the end of the next heating

phase or until a different mode is activated.

4.6.4 “Setback” mode

The allocated heating circuit is set to setback mode until the start of the next heating

phase or until a different mode is activated. The temperature setpoint displayed in

setback mode on the basic screen is for display purposes only and cannot be

changed. To change this, go to the “Heating” menu → under the “Temperature” tab.

4Operation

Set the heating circuit mode

16 Froling GesmbH | A-4710 Grieskirchen, Industriestraße 12 | www.froeling.com

5 Menu overview and parameters

5.1 Heating

5.1.1 Heating - Status

System menu Heating

Control heating circuit according to program (NO -> heating circuit is switched off) YES

▪YES: The heating circuit is operated according to the selected heating times.

▪NO: Heating circuit is completely switched off, frost protection remains active!

Actual flow temperature 46°C

Shows the current flow temperature.

Flow temperature setpoint 52°C

Shows the calculated flow temperature setpoint.

Room temperature 20°C

Prerequisite: Heating circuit used in conjunction with remote control

Shows the current room temperature.

Override switch Auto

Prerequisite: Heating circuit used in conjunction with remote control

Shows the current heating circuit mode:

▪Party: party mode; the current or next setback program is ignored

▪Setback: setback mode; the heating phases are ignored

▪Auto: automatic mode: heating phases according to the set heating times

▪Off: switched-off; heating circuit deactivated, only frost protection!

Outside air temperature 2°C

Shows the current external temperature.

Menu overview and parameters 5

Heating

Operating Instructions RBG 3200 Touch | B0780115_en 17

5.1.2 Heating - Temperatures

System menu Heating

Desired room temperature during heating mode 20°C

Prerequisite: Heating circuit used in conjunction with remote control

Room temperature which is regulated during the set heating times

Desired room temperature during setback mode 16°C

Prerequisite: Heating circuit used in conjunction with remote control

Room temperature which is regulated outside of the set heating times

Flow temperature SP at external temperature of +10°C 40°C

First setting point for definition of heating curve

Flow temperature SP at external temperature of -10°C 60°C

Second setting point for definition of heating curve

Reduction of flow temperature in setback mode 15°C

The flow temperature is reduced by this value during setback mode.

External temperature below which the heating circuit pump switches on in heating mode 18°C

If the external temperature exceeds this value during heating, the heating circuit pumps and mixing valve are

deactivated.

5Menu overview and parameters

Heating

18 Froling GesmbH | A-4710 Grieskirchen, Industriestraße 12 | www.froeling.com

External temperature below which the heating circuit pump switches on in setback mode 7°C

If the external temperature falls below this value in setback mode, the heating circuit pumps and mixing valve

are activated.

Frost protection temperature 10°C

If the room temperature or the flow temperature is lower than the set value, the heating circuit pump will be

switched on and the heating circuit mixer keeps to the maximum heating circuit flow temperature that is set.

5.1.3 Heating - Times

System menu Heating

⇨ See "Setting times" [page 13]

Menu overview and parameters 5

Heating

Operating Instructions RBG 3200 Touch | B0780115_en 19

5.2 Water

5.2.1 Water - Status

System menu Water

DHW tank top temperature 58°C

Current temperature of the DHW tank. The DHW tank is heated when the time window for the DHW tank load‐

ing is reached and the current temperature of the DHW tank has fallen below the value using the parameter

“Reload if DHW tank temperature is below”. A loading of the DHW tank takes place when either

the time window has elapsed or the temperature value which is set under “Set DHW temperature” is

reached.

DHW tank bottom temperature 55°C

Prerequisite: Solar panel system is regulated by Froling!

Current temperature in the area of the reference sensor of the solar panel system.

DHW tank pump control 0%

Specifies the speed of the DHW tank pump as a percentage of maximum speed.

5Menu overview and parameters

Water

20 Froling GesmbH | A-4710 Grieskirchen, Industriestraße 12 | www.froeling.com

Page is loading ...

Froling RBG 3200 Touch Operating Instructions Manual

Froling RBG 3200 Touch Operating Instructions Manual

Froling RBG 3200 Touch Operating Instructions Manual

Related papers

Other documents