Estyma IGNEO Touch User manual

Brand: Estyma

Model: IGNEO Touch

Type: User manual

User manual

EG-Pellet

Table of contents
Chapter 1. General information 4
1  Introduction................................................................................................................................................... 4
2  Safety.............................................................................................................................................................. 4
3  Disposal of Waste of Electrical and Electronic Equipment ...............................................................5
Chapter 2. Basic controller operation 6
1  Main screen................................................................................................................................................... 6
1.1  DATE AND TIME - SETTING........................................................................................................7
1.2  TURNING THE BOILER ON/OFF................................................................................................7
1.3  TURNING ON/ OFF the boiler, water, heating........................................................................7
1.4  SUMMER (only water heating)......................................................................................................7
1.5  SETTING THE TARGET BOILER TEMPERATURE (program) ...............................................8
1.6  FUEL FILLING (setting the fuel level)..........................................................................................8
2  Menu structure............................................................................................................................................. 9
Chapter 3. Detailed description of screens/functions 10
1  Boiler............................................................................................................................................................ 10
1.1  SET TARGET TEMPERATURE AND OPERATING MODE..................................................10
1.2  SETTINGS........................................................................................................................................10
2  Schedules..................................................................................................................................................... 11
3  Heating and hot water operation modes.............................................................................................12
4  Heating......................................................................................................................................................... 12
4.1  SETTINGS........................................................................................................................................12
5  Hot water..................................................................................................................................................... 13
5.1  SETTINGS........................................................................................................................................13
6  Burner........................................................................................................................................................... 13
6.1  SETTINGS........................................................................................................................................13
7  Buffer............................................................................................................................................................ 14
7.1  SETTINGS........................................................................................................................................14
8  Solar heating............................................................................................................................................... 14
8.1  SETTINGS........................................................................................................................................14
9  Alarms........................................................................................................................................................... 14
www.estyma.pl 3 
EGP-EN 20171024

IGNEO touch user manual

Chapter 1. General information

Thank you for choosing our product and congratulations on the best decision. We are happy to hear your comments

about the device.

ESTYMA electronics Team

1.1 INTRODUCTION

The boiler regulator IGNEO Touch is a modern microprocessor system, which manages not only the boiler, but

also the heating system. In the full configuration, the regulator can manage:

4 central heating circuits

1 hot water circuit.

1 buffer

1 solar heating system

1 additional fuel storage system

Thanks to advanced algotithm and the possibility to regulate multiple parameters, the system can be well adjusted

to the heating system needs.

1.2 SAFETY

ATTENTION! Electrocution risk!

Turn off power on the electric switchboard before assembly or disassembly.

Carefully read the instruction before use.

Keep the instruction manual and consult it when using the device.

Abide by the rules of use and warnings written in the instruction manual.

Check if the device isn't dammaged. When in doubt, don't use the device and contact the retailer.

If you encouter situations not mentioned in the instruction manual, or you are in doubt about safe usage

of the device, please contact the retailer.

Pay attention to any warning symbols on the device or packaging.

The device must be used in accordance with intended use.

The device is not a toy, keep out of childrens reach.

Under no circumstances allow children to play with any part of the packaging.

Keep small parts (screws, wall plugs etc.) away from children. Small elements supplied with the device can

be a choking hazard.

Do not modify mechanical or electrical parts of the device. It can result in abnormal functioning, malfunctions,

errors and failure to comply with regulations.

Do not put anything into any openings in the device. It can cause short circuits, electric shock, fire or

complete destruction of the device.

Do not allow the device to come in contact with water, moisture or dust. It can cause short circuits,

electric shock, fire or complete destruction of the device.

4www.estyma.pl

EGP -EN 20171024

Chapter 1. General information

After turning off the device using touch panel, it can still be under power.

This regulator is designed as a part of a boiler, not a standalone device.

This device requires a proper ventilation. Do not cover any ventilation holes to assure a proper air circulation.

For inside use only, unless stated otherwise.

Do not expose to impacts or vibrations.

Before installing verify if electrical grid parameters are within specifications.

To ensure electric shock protection, verify that the device is grounded. It must be connected with a 3 pin

socket. The power socket must be installed by an authorized electrician.

Verify if the device will not cause power grid overload. Do not connect the device to a circuit containing

electric motors and other impulse disruption sources (freezers, washing machines etc.)

Before connecting any wires or external devices, turn off mains supply.

To completely turn off the device, pull the plug out of the socket. Especially if it will not be used for an

extended ammount of time.

The power cord must be protected from damage. It must not be stepped on and no objects should be

placed on it.

The regulator must be installed by the boiler producer. Any electrical connections must comply with

circuit diagrams and local standards and regulations.

Additional safety devices must be used to protect the boiler and heating elements from eventual regulator

malfunctions or software errors.

This device has no replaceable parts. All servicing and repair, apart from cleaning and circuit breaker replacement

(electrical grid disconnected) and changing settings must be performed by an authorized profesionals.

Before any service activity disconnect the device from any power sources.

Do not use gasoline, solvents or other chemicals for cleaning. It can damage the panel. Use soft cloth instead.

If the power cord is damaged, do not use the device. Damaged cable must be replaced with one with the

same parameters by the service department.

Settings must be adjusted to a type of boiler and fuel, accomodating for all other conditions. Incorrect

settings can result in failure. In extreme cases it can lead to life threatenig situations.

The regulator is ment to be installed by a boiler producer. Before using it in a device, the producer must

verify that it's compatible with the boiler type, and its use will not cause any danger or malfunctions.

1.3 DISPOSAL OF WASTE OF ELECTRICAL AND ELECTRONIC EQUIPMENT

This electronic device consists of partly recycleable materials. It has to be disposed of by taking it to a designated used

electric and electronic equipment collection point or a retailer. It should not be mixed with general household waste.

www.estyma.pl 5

EGP-EN 20171024

IGNEO touch user manual

Chapter 2. Basic controller operation

2.1 MAIN SCREEN

Screen settings:

NUMBER DESCRIPTION

1Current time. On pressing, the change of hour screen is displayed.

2Burner status.

3Measured boiler temperature.

4Day of the week. On pressing, the change of date screen is displayed.

5Measured outside temperature.

6Set target temperature of the boiler and boiler mode. On pressing it changes.

7Enter the menu button.

8Enter the fuel level settings button. The button also displays the rest of the fuel and informs about the

reserves.

9 Quick enter the burner menu button. Lit lamp means the burner is working.

10,11 Quick enter the heating menu button. Lit lamp means the circuit is working.

12 Quick enter the hot water menu button. Lit lamp means that the water preparation is working.

13 Advanced button. Long press (>3 sec) turns the boiler off. Lit lamp means that the boiler is working,

LED description:

LETTER DESCRIPTION

A (green) Boiler. It is lit if the boiler is working.

B (yellow) Burner. It is lit if there is a flame, it is flashing if the burner is working but there is no flame (eg. inflaming,

putting out). It is not lit if the burner is not working and there is not flame.

C (red) Alarm. It is flashing if the alarms are active. It is lit if there are unconfirmed alarms.

6www.estyma.pl

EGP -EN 20171024

Chapter 2. Basic controller operation

2.1.1 DATE AND TIME - SETTING

To set the date or time on the main screen, press the date or the hour. The window to set the date or hour will appear.

2.1.2 TURNING THE BOILER ON/OFF

In order to turn the boiler on or off, press the button on

the main screen for 3 seconds.

2.1.3 TURNING ON/ OFF the boiler, water, heating

On pressing the button on the main screen it is possible to quickly turn on/off (change of the operating mode) of

certain heating system elements.

ATTENTION! If there are more than two heating system circuits, you should enter the menu, and

then go to the circuit number 3 and 4 to change the heating program.

2.1.4 SUMMER (only water heating)

To turn on summer mode (heating only hot water circuit), press the On/Off button and move all the ''Heating''

sliders to ''off''.

ATTENTION! If there are more than two heating circuits in the system you should enter the

menu and then go to the circuit number 3 and 4 to turn off the heating.

www.estyma.pl 7

EGP-EN 20171024

IGNEO touch user manual

2.1.5 SETTING THE TARGET BOILER TEMPERATURE (program)

To change the boiler target temperature or the boiler working program you should press the button with the

target temperature and the current program on the main screen, and then set the temperature or change the

program.

The programs are described in 3.1.1.

2.1.6 FUEL FILLING (setting the fuel level)

The regulator was equipped with the ability to calculate the remaining fuel in the tank. To make calculating

possible, each time after adding fuel you should set the amount of the fuel in the tank. The amount is set by the

buttons ''+'' and ''-'' or by the slider.

This screen also allows to turn on the fuel conveyor manually. In case of comlete fuel depletion it allows to fill the

conveyor tube again.

To enter the fuel level menu, press the ''8'' button on the main screen.

8www.estyma.pl

EGP -EN 20171024

Chapter 2. Basic controller operation

2.2 MENU STRUCTURE

www.estyma.pl 9

EGP-EN 20171024

IGNEO touch user manual

Chapter 3. Detailed description of screens/functions

3.1 BOILER

3.1.1 SET TARGET TEMPERATURE AND OPERATING MODE

Boiler target set temperature and operating mode can be

regulated after pressing number ''6'' on the main screen.

The following table presents available boiler operating modes.

SYMBOL NAME DESCRIPTION

manual The boiler temperature is set directly by the user. The boiler works to maintain the

set target temperature.

automatic

The boiler temperature is set automatically on the basis of the current need of the

heating circuits, hot water circuits or the buffer.

When there's no need to heat the water, the temperature will be set to minimum

of 7°C (antifreeze mode), and the boiler will turn on only when needed.

time- manual The boiler temperature is set as in the manual mode, but the boiler can work only

in set time limits.

time- automatic The boiler temperature is set as in the automatic mode, but the boiler can work

only in set time limits.

3.1.2 SETTINGS

NAME DESCRIPTION

Set temperature [°C] The set temperature in manual or time manual mode.

Switching hysteresis [°C] The burner is turned on when the temperature in the boiler is lower than the set

temperature, minus the switching hysteresis.

Hysteresis exemption [°C] The burner is turned off if the temperature in the boiler is higher than the set

temperature plus hysteriesis exemption.

10 www.estyma.pl

EGP -EN 20171024

Chapter 3. Detailed description of screens/functions

3.2 SCHEDULES

To enter the schedule menu, press the schedule button

on the boiler, heating or hot water menu.

The regulator allows for the work of the boiler, heating

and hot water according to the set schedules for each

day of the week separately.

After selecting a day, the window with daily schedule will

appear.

To select a program for a certain hour, click or slide the

hour dial, setting the time and press the ''eco'' or ''comf''

button.

After setting the program, slider moves to another hour.

The regulator is equipped with a convenient function of

copying the mode for other days of the week.

www.estyma.pl 11

EGP-EN 20171024

IGNEO touch user manual

3.3 HEATING AND HOT WATER OPERATION MODES

Both heating and the hot water can be prepared in several modes.

The meaning of the modes is analogical to both cases and it is presented in the table.

SYMBOL NAME DESCRIPTION

comfort The comfort temperature is maintained all the time.

time Works according to the time limit.

economic The ecomomy temperature is maintained all the time.

turned off The circuit is turned off. Only protection functions work.

3.4 HEATING

To enter the heating menu on the main screen, press

buttons ''10'' or ''11''.

There are current and set temperatures, as well as the

mode, displayed on the screen.

Also symbols for currently working system elements are

visible.

3.4.1 SETTINGS

NAME DESCRIPTION

Comfort temperature [°C] Set temperature in the room in the comfort range, with the time mode or the

comfort mode.

Economical temperature [°C] Set temperature in the room in the economic range, with the time mode or the

economic mode.

Hysteresis [°C] The accuracy of maintaining the set target temperature in the room. It may also

affect the frequency of the boiler inset. If the hysteresis is higher the burner turns

on with lower frequency for a longer period of time.

Room sensor calib. [°C] Calibrating the chosen sensor.

Work mode Chosen operating mode of the circuit.

HC temp. set manually [°C] Set temperature for the instalation when the weather steering is not chosen.

Temp. HC for -20°C [°C] Set temperature for the instalation when the outside temperature is below -20°C

Temp. HC for 0°C [°C] Set temperature for the instalation when the outside temperature is below 0°C

Temp. HC for 10°C [°C] Set temperature for the instalation when the outside temperature is above 10°C

12 www.estyma.pl

EGP -EN 20171024

Chapter 3. Detailed description of screens/functions

3.5 HOT WATER

To enter the hot water menu on the main screen, press

number ''12''.

There is current temperature and set target temperature,

as well as the chosen mode, displayed on the screen.

Also symbols for currently working system elements are visible.

3.5.1 SETTINGS

NAME DESCRIPTION

Comfort temperature [°C] The set hot water temperature in the comfort range in the time mode or the

comfort mode.

Economical temperature [°C] The set hot water temperature in the economic range in the time mode or the

economic mode.

Heat now One time hot water heating to the comfort temperature, regardless of the mode.

Hysteresis [°C] The hot water heating starts when the temperature in the tank is lower than the

set temperature minus hysteresis.

Antilegionella Enables weekly water heating to decrease the risk of legionella infection. The

heating process starts at 1 a.m every wednesday.

Hot water priority Sets Hot Water priority. C/H pump is not engaged when H/W is heated.

3.6 BURNER

To go to the burner menu on the main screen, press ''9''.

Symbols for currently working system elements and the

burner status should appear.

3.6.1 SETTINGS

NAME DESCRIPTION

Air correction [%] Correction of air programmed by the instrallator for the burning process.

Min power [%] Lower limit for burner power modulation.

Max power [%] Upper limit for burner power modulation.

www.estyma.pl 13

EGP-EN 20171024

IGNEO touch user manual

3.7 BUFFER

To enter the buffer menu, press the button number ''7''

on main menu and choose ''BUFFER''

3.7.1 SETTINGS

NAME DESCRIPTION

Min. temp. (top) [°C] Start heating the buffer if temperature drops below this point.

Max. temp. (bottom) [°C] Stop heating the buffer if temperature raises above this point.

3.8 SOLAR HEATING

To enter the solar heating menu, press the button number

''7'' on main menu and choose ''SOLAR HEATING''.

3.8.1 SETTINGS

NAME DESCRIPTION

Flow (l/min) Flow rate in solar installation. This parameter is used to correctly calculate the

power.

Delta switch on [°C] Solar heating pump is turned on when the temperature difference between the

solar collector and the water tank exceeds this value.

Delta switch off [°C] Solar heating pump is turned off when the temperature difference between the

solar collector and the water tank falls below this value.

3.9 ALARMS

The driver includes the history of alarms which is saved in

the memory. If there are any active or unconfirmed

alarms, on the main screen alarm icon will appear. On

pressing it, the history will be displayed, where the last 20

alarms are stored.

14 www.estyma.pl

EGP -EN 20171024

Produced by:

estyma electronics

al. Lipowa 4

11-500 Giżycko

POLAND

tel. +48 87 429 86 75

fax +48 87 429 86 75

[email protected]

www.estyma.pl

Estyma IGNEO Touch User manual

Brand: Estyma

Model: IGNEO Touch

Type: User manual

Download PDF

report

Estyma IGNEO Touch User manual

Estyma IGNEO Touch User manual

Other documents