Vita CLASSIC Barcelona Planter Box Operating instructions

Vita
Brand
Vita
Model
CLASSIC Barcelona Planter Box
Type
Operating instructions
1. Pre-Assembled Side Wall Panels (2) -
10610
2. Post Caps (4) - 10611
3. Floor Panel (with tongue) (1) - 11200
4. Floor Panel (with groove) (1) - 10612
5.
Pre-Assembled Front/Back Wall Panels with Posts
(2) - 10613
6. 1 1/2” (38 mm) Self-Auguring Stainless Steel Screws (16) - 20005
Tools You Will Need
• Cordless Drill
• Hammer
General Information
• Read Instructions through caref
ully before beginning assembly.
•
When
assembling components, place on a non-abrasive surface
(i.e. shipping box)
to avoid scratching.
•
We recommend an area approx 4’x 8’
(1.2 m x 2.4 m) for un
obstructed
assembling.
• Y
ou
should not need to use excessive force when assembling components.
The Barcelona Planter Box
Please read through before starting assembly.
Check Box for T
hese Contents
I
In the event of missing or defective parts please call our customer service dept. at 1 800 282 9346 (Mon. to Fri. 8:00 AM to 5:00 PM EST).
ASSEMBLY INSTRUCTIONS
6
1
Not to Scale
27"
(69 cm)
20"
(51cm)
21"
(53cm)
17"
(43 cm)
1
21.75" (55 cm)
STEP ONE
Layout front wall panel on the work surface.
Insert the side walls into the routed holes on the front wall
panel posts.
Connect the Front & Back Wall
to the Side Wall Panels
1
2
1
2
1
4
3
2
V1.5 May 14-21
www.wearevita.com
5
Pressure fit into place the floor panels.
The Barcelona Planter Box
7
8
3
Install the four post caps
.
Optional
To Attach the Luxembourg
Privacy Screen to this Planter Box
(Purchase Separately).
Remove two post caps.
Attach trellis or privacy screen by over-sleeving the bulbed out
bottom end of the posts over the protruding posts of the planter
box until they both bottom out inside each other.
Install screws in the four pre-drilled holes at the bottom of each
post.
Discard the two post caps from planter box and ground
mounting extensions that come with trellis.
Optional
Fit the opposite back wall panel over the side walls.
Reposition the assembled planter box so it stands upright on
the work surface. Ensure at this point the planter walls are square
to each other. This can be accomplished by making sure that
the corner to opposite corner measurement both ways are equal.
3
4
5
Using the screws provided, secure the side wall panels into the front
and back wall panels with 2 screws at the ends of the rails.
Ensure that panels are fully flush inside the posts and the wall
panels are square to each other. Screws should only be drilled in
half of the length so that panels do not pull out of the posts
when under stress. ** Please note the screws are used as stoppers only.
6
Invert the planter boxand repeat th
is same process at the
opposite end of each of the four post.
STEP TWO
Insert Floor Panels & Post Caps
A
8
3
B
8
C
2
4
7
6
5
8
A
B
www.wearevita.com
North America Toll Free Phone: 1 800 282 9346
  • Page 1 1
  • Page 2 2

Vita CLASSIC Barcelona Planter Box Operating instructions

Vita
Brand
Vita
Model
CLASSIC Barcelona Planter Box
Type
Operating instructions
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents