2. Kutai
  3. PTM-15

Kutai PTM-15 Owner's manual

  • Hello! I've reviewed the Operation Manual for the PTM-15 DC Power Supply Module from KUTAI. This manual covers the module's specifications, installation, and features, including its ability to convert AC power to a stable DC output for ATS systems. I'm ready to assist you with any questions you might have about this product.
  • What is the AC Input Voltage range?
    What is the DC output voltage?
    What are the recommended wire sizes for AC and DC connections?
    What protection features does the module have?
KUTAI ELECTRONICS INDUSTRY CO., LTD.
TEL : +886-7-8121771 FAX : +886-7-8121775 Website : www.kutai.com.tw
Headquarters : No.3, Ln. 201, Qianfu St., Qianzhen Dist., Kaohsiung City 80664, Taiwan
PTM-15
DC Power Supply Module for ATS
Operation Manual
___________________________________________________________________________________________
2 PTM-15
SECTION 1 : INTRODUCTION
The PTM-15 DC Power Supply connects to the Utility
and Standby AC power inputs of an Automatic Transfer
Switch (ATS) and converts these voltages into a set of
DC power outputs. The module provides
a stable operating power supply to the control circuit for
the Kutai ATS-245-DC controller or the DC-type
BTB-ATS, which require DC power. The module is for
use in installation sites without DC power supply or
where DC power supply is difficult to obtain.
SECTION 2 : SPECIFICATION
AC Power Input (L, N)
Operating Environment
Voltage 90 305 Vac single-phase, 2-wire
Operating Temperature -20 to +60 ˚C
Frequency 50/60 Hz
Storage Temperature -40 to +85 ˚C
Fuse specification : 5 x 20mm S505-1A, slow blow
Relative Humidity Max. 95%
Recommended wire size : 1.25mm² (AWG16)
Vibration 5 Gs @ 60 Hz
DC Power Output (D+, D-)
Dimensions
Voltage 15 Vdc +/- 1%
135.0 (L) x 100.0 (W) x 42.0 (H) mm
Current Max. 0.6 A
5.31 (L) x 3.94 (W) x 1.65 (H) inch
Recommended wire size : 1.25mm² (AWG16)
Weight
Protection Functions
410 g +/- 2%
DC Output Short Circuit Protection
0.9 lb +/- 2%
DC Output Over Voltage Protection
SECTION 3 : OVERVIEW OF PTM-15 EXTERNAL FEATURES
※ Use only replacement fuses specified in this user manual.
※ Appearance and specifications of products are subject to change for improvement without prior notice.
Utility
Standby
L
N
DC Output D+
D-
FUSE/250V 1A
FUSE/250V 1A
L
NL1
L2
Utility Power Input
Protection Fuse
Utility Power Input
Terminals
90 305 Vac
Standby Power Input
Terminals
90 305 Vac
Standby Power Input
Protection Fuse
___________________________________________________________________________________________
PTM-15 3
SECTION 4 : APPEARANCE / DIMENSIONS / INSTALLATION DRAWING
Unit : mm
[inch]
M5 L35
5.4
[0.21"]
42.0
[1.65"]
20.0
[0.79"]
135.0
[5.31"] 114.0
[4.49"]
80.0
[3.15"]
100.0
[3.94"]
SECTION 5 : RECOMMENDED WIRING DIAGRAM
StanbyUtility
L3
N
L1
L2
LOAD
L3
N
L1
L2
PowerPower
PTM-15 Module
L N LN
D+
D-
Utility Stanby
DC Output B +
B -
ATS Controller
/