Energizer 8970600 Owner's manual

Brand: Energizer

Model: 8970600

Category: Battery chargers

Type: Owner's manual

Energizer 8970600

The Energizer 8970600 is a battery charger designed for charging LEAD-ACID batteries, including AGM, STD, WET, CAL, and GEL batteries. It is not intended for charging other types of batteries, such as Lithium batteries or dry-cell batteries.

The charger has several safety features to help prevent accidents, including:

Reverse polarity protection
Overcharging protection
Short circuit protection
Overheating protection

It also has an adjustable charge rate, so you can choose the right setting for your battery. The charger is easy to use and comes with a detailed instruction manual.

Energizer 8970600

The charger has several safety features to help prevent accidents, including:

Reverse polarity protection
Overcharging protection
Short circuit protection
Overheating protection

It also has an adjustable charge rate, so you can choose the right setting for your battery. The charger is easy to use and comes with a detailed instruction manual.

MODEL: ENC2A

BATTERY CHARGER

OPERATOR'S MANUAL

IMPORTANT SAFETY INSTRUCTIONS

1. SAVE THESE INSTRUCTIONS. This manual contains important safety and operating

instructions. You may need to refer to these instructions at a later date.

2. CAUTION. To reduce risk of injury, charge only a LEAD-ACID battery, including AGM,

STD, WET, CAL and GEL. Charging other types of batteries, like Lithium batteries or dry-cell

batteries, may burst causing personal injury and property damage.

3. Do not expose charger to rain or snow.

4. Use of an attachment not recommended or sold by the battery charger manufacturer may

result in a risk of fire, electric shock, or injury to persons.

5. To reduce risk of damage to electric plug and cord, pull by plug rather than cord when

disconnecting charger.

6. Make sure cord is located so that it will not be stepped on, tripped over, or otherwise

subjected to damage or stress.

7. An extension cord should not be used unless absolutely necessary. Use of improper

extension cord could result in a risk of fire and electric shock. If an extension cord must be

used, make sure:

a. That pins on plug of extension cord are the same number, size, and shape as those of

plug on charger;

b. That extension cord is properly wired and in good electrical condition; and

c. If the length of the extension cord is less than 15 meter, use a 0.75mm2 cord, If 30meter -

1mm2, 60 meter -1.5mm2.

8. Do not operate charger with damaged cord or plug, replace the cord or plug immediately.

9. Do not operate charger if it has received a sharp blow, been dropped, or otherwise

damaged in any way; take it to a qualified serviceman.

10. Do not disassemble charger; take it to a qualified serviceman when service or repair is

required. Incorrect reassembly may result in a risk of electric shock or fire.

11. To reduce risk of electric shock, unplug charger form outlet before attempting any

maintenance or cleaning. Turning off controls will not reduce this risk.

12. WARNING - RISK OF EXPLOSIVE GASES

a. WORKING IN VICINITY OF A LEAD-ACID BATTERY IS DANGEROUS. BATTERIES

GENERATE EXPLOSIVE GASES DURING NORMAL BATTERY OPERATION. FOR THIS

REASON IT IS OF UTMOST IMPORTANCE THAT EACH TIME BEFORE USING YOUR

CHARGER, YOU READ THIS MANUAL AND FOLLOW THE INSTRUCTIONS EXACTLY.

b. To reduce risk of battery explosion, follow these instructions and those published by

battery manufacturer and manufacturer of any equipment you intend to use in vicinity of

battery. Review cautionary marking on these products and on engine.

13. PERSONAL PRECAUTIONS

a. Someone should be within range of your voice or close enough to come to your aid when

you work near a lead-acid battery.

b. Have plenty of fresh water and soap nearby in case battery acid contacts skin, clothing, or

eyes.

c. Wear complete eye protection, and clothing protection. Avoid touching eyes while working

near battery.

d. If battery acid contacts skin or clothing, wash immediately with soap and water. If acid

enter eye, immediately flood eye with running cold water for at least 10 minutes and get

medical attention immediately.

e. NEVER smoke or allow a spark or flame in vicinity of battery or engine.

f. Be extra cautious to reduce risk of dropping a metal tool onto battery. It might spark or

short circuit battery or other electrical part that may cause explosion.

g. Remove personal metal items such as rings, bracelets, necklaces, and watches when

working with a lead-acid battery. A lead-acid battery can produce a short circuit current high

enough to weld a ring or the like to metal, causing a severe burn.

h. Use charger for charging a LEAD-ACID battery only. It is not intended to supply power to a

low-voltage electrical system other than in a starter motor application. Do not use battery

charger for charging dry-cell batteries that are commonly used with home appliances. These

batteries may burst and cause injury to persons and damage to property.

i. NEVER charge a frozen battery.

14. PREPARING TO CHARGE

a. If necessary to remove battery from vehicle to charge, always remove the grounded

terminal from battery first. Make sure all accessories in the vehicle are off, so as not to cause

an arc.

b. Be sure area around battery is well ventilated while battery is being charged. Gas can be

forcefully blown away by using a piece of cardboard or other non-metallic material as a fan.

c. Clean battery terminals. Be careful to keep corrosion from coming in contact with eyes.

d. Add distilled water in each cell until battery acid reaches level specified by battery

manufacturer. This helps purge excessive gas from cells. Do not overfill. For a battery

without cell caps, carefully follow manufacturer's recharging instructions.

e. Study all the battery manufacturer's specific precautions such as removing or not

removing cell caps while charging and recommended rates of charge.

f. Determine voltage of battery by referring to car owner's manual and make sure that output

voltage selector switch is set at correct voltage.

If charger has adjustable charge rate, charge battery initially at lowest rate.

15. CHARGER LOCATION

a. Locate charger as far away from battery as dc cables permit.

b. Never place charger directly above battery being charged; gases from battery will corrode

and damage charger.

c. Never allow battery acid to drip on charger when reading gravity or filling battery,

d. Do not operate charger in a closed-in area, or restrict ventilation in any way.

e. Do not set a battery on top of charger.

16. DC CONNECTION PRECAUTIONS

a. Connect and disconnect dc output clips only after setting any charger switches to off

position and removing ac cord from electric outlet.

Never allow clips to touch each other.

b. Attach clips to battery posts and twist or rock back and forth several times to make a good

connection. This tends to keep the clips from slipping off terminals and helps to reduce risk of

sparking.

17. FOLLOW THESE STEPS WHEN BATTERY IS INSTALLED IN VEHICLE. A SPARK

NEAR BATTERY MAY CAUSE BATTERY EXPLOSION. TO REDUCE RISK OF A SPARK

NEAR BATTERY:

a. Position ac and dc cords to reduce risk of damage by hood, door, or moving engine part.

b. Stay clear of fan blades, belts, pulleys, and other parts that can cause injury to persons.

c. Check polarity of battery posts. POSITIVE (POS, P, +) battery post usually has larger

diameter than NEGATIVE (NEG, N, -) post.

d. Determine which post of battery is grounded (connected) to the chassis. If negative post is

grounded to chassis (as in most vehicles), see item "e". If positive post is grounded to the

chassis, see item "f".

e. For negative-grounded vehicle, connect POSITIVE (RED) clip from battery charger to

POSITIVE (POS, P, +) ungrounded post of battery.

Connect NEGATIVE (BLACK) clip to vehicle chassis or engine block away from battery. Do

not connect clip to carburetor, fuel lines, or sheet metal body parts. Connect to a heavy gage

metal part of the frame or engine block.

f. For positive-grounded vehicle, connect NEGATIVE (BLACK) clip from battery charger to

NEGATIVE (NEG, N, -) ungrounded post of battery. Connect POSITIVE (RED) clip to vehicle

chassis or engine block away from battery. Do not connect clip to carburetor, fuel lines, or

sheet-metal body parts. Connect to a heavy gage metal part of the frame or engine block.

g. When disconnecting charger, turn switches to off, disconnect AC cord, remove clip from

vehicle chassis, and then remove clip from battery terminal.

h. See operating instructions for length of charge information.

18. FOLLOW THESE STEPS WHEN BATTERY IS OUTSIDE VEHICLE. A SPARK NEAR

THE BATTERY MAY CAUSE BATTERY EXPLOSION. TO REDUCE RISK OF A SPARK

NEAR BATTERY:

a. Check polarity of battery posts. POSITIVE (POS, P, +) battery post usually has a larger

diameter than NEGATIVE (NEG, N, -) post.

b. Attach at least a 60cm-long 16mm2 insulated battery cable to NEGATIVE (NEG, N, -)

battery post.

c. Connect POSITIVE (RED) charger clip to POSITIVE (POS, P, +) post of battery.

d. Position yourself and free end of cable as far away from battery as possible - then connect

NEGATIVE (BLACK) charger clip to free end of cable.

e. Do not face battery when making final connection.

f. When disconnecting charger, always do so in reverse sequence of connecting procedure

and break the first connection while as far away from battery as practical.

g. A marine (boat) battery must be removed and charged on shore. To charge it on board

requires equipment specially designed for marine use.

19. AC POWER CORD CONNECTION INSTRUCTIONS

The plug must be plugged into an outlet that is properly installed in accordance with all local

codes and ordinances.

DANGER. Never alter AC cord or plug provided - if it will not fit outlet, have proper outlet

installed by a qualified electrician. Improper connection can result in a risk of an electric

shock. This battery charger is for use on a nominal 110-volt circuit.

20. LENGTH OF CHARGE

The following instruction will allow you to determine how long it will take to bring a specific

battery to full charge.

a. Test the battery for state of charger with a hydrometer or electronic percent-of-charge

tester.

b. Determine the size of the battery in Amp-Hour or Reserve Capacity. If the ratings are not

printed on the battery, contact your local battery dealer for this information. These are the

only ratings that can be used to determine length to charging time.

c. Use the battery rating, the charge level of the battery, and amp setting to be used on the

charger in the formula provided below.

Amp Hour Rating of Battery × Percent of Charged Needed

× 1.25 = Hours to Charge

Amp Setting Selected On Charger

d. If the battery is rated in Reserve Capacity, use the following formula to convert reserve

capacity to amp-hours.

Reserve Capacity

+ 15.5 = Amp-Hour Rating

NOTE: The length of charge times are approximate and vary from the battery to battery.

Always follow the battery manufacturer’s specific charging instructions.

21. OPERATING INSTRUCTIONS

Before using review all safety and connection directions before using charger. Failure

to do so can damage battery and cause serious injury or death.

FEATURES:

All automatic chargers come with an Automatic Float Charge circuit, LED digital display

ENC2A

SELECT VOLTAGE switch with the following selections:

2.0A–6V and 2.0A–12V

6V Indicator LED(flash charging, solid charged)

12V Indicator LED(flash charging, solid charged)

Error Indicator LED

Charging:

·Connect the charger to battery per instructions in sections 16 & 17 or 18.

·Connect the charger to AC outlet.

·Select the appropriate charger voltage for your battery.

·If the charger does not detect a properly connected battery, the Error LED will light until such

a battery is detected. Charging will not begin while the Error LED is on. When the charging

begins, the 6v(HFP2.0DV only) or 12v LED will be lit.

·When charging is complete, unplug the charger from the AC outlet.

Automatic Micro Processor Control Unit Charge:

Stage 1 —Diagnosis: Analysis the battery can accept charge or not, prevent charging from

proceeding on the a defective battery;

Stage 2—Pre-charge: Battery V <12V, small current to charge, better maintenance battery;

Stage 3 — Soft start: Bulk charging process with a gentle (soft) charge.

Stage 4—CC (Constant Current):Fast speed charging;

Stage 5—CV(Constant Voltage)Absorption to voltage 14.6V, This is a charge cycle for

batteries nearly full. It will top off the battery at 14.6VDC;

Stage 6—Resting: Cut off with full charged statement, high energy efficiency;

Stage 7—Restoring: Automatic On-off Monitoring. The charger dc output will shut off and

monitor a fully charged battery. If the battery falls below 12.8VDC, the charger will restart and

enter into stage one.

22. POSSIBLE CHARGING PROBLEMS

PROBLEM

CAUSE

SOLUTION

Bad Battery

The Error LED may light when the

battery voltage is less than 1.5V

and more than0.5V, or the voltage

is more than 7.5V(6V mode

HFP2.0DV only) 15V (12V mode);

The battery voltage is lower than

5.5V(6V HFP2.0DV

only ),11V(12V),after charging 20

minutes;

Have the battery tested by a qualified

technician.

Battery not

accepting

a charge

·Lack of AC input power

·Faulty connections to battery

terminals

·Wrong charge voltage selection

·Battery voltage too low

·Charging a very cold battery

·Make sure that the charger is plugged into

AV outlet and the POWER LED is lit.

·Unplug the charger and check the battery

connection; ensure that there is a good

connection at the battery terminal/post

and/or vehicle chassis.

·Check that the correct charge voltage was

selected for the battery being charged.

·Ensure enough charging time was allowed

to charge battery.

·If the battery to be charged is extremely

cold(in temperatures below freezing 0℃), it

will not accept a high rate of charge, so the

initial charger rate will be slow. The rate of

charger will increase as the battery warms.

Never attempt to charge a frozen battery.

23. MAINTANENCE INSTRUCTIONS

This charger requires minimal maintenance. As with any appliance or tool, a few common

sense rules will prolong the life of the battery charger.

ALWAYS BE SURE THE CHARGER IS UNPLUGGED BEFORE PERFORMING ANY

MAINTENANCE OR CLEANING.

1. Store in a clean, dry place

2. Coil up the cords when not in use.

3. Clean the case and cords with a slightly damp cloth.

4. Clean any corrosion from the clamps with a solution of water and baking soda.

5. Examine the cords periodically for cracking or other damage and have them replaced if

necessary.

6. WARNING: All other service should be done by qualified personnel only.

Warranty and Return

Warranty by PowerBright

What does this warranty cover? This Limited Warranty is provided by PowerBright and

covers defects in workmanship and materials in your ENC2A. This warranty period lasts for

24 months from the date of purchase at the point of sale to you, the original end user

customer. Proof of purchase is required to make warranty claims.

What will PowerBright do? PowerBright will, at its option, repair or replace the defective

product free of charge, provided that you notify PowerBright of the product defect within the

Warranty Period, and provided that PowerBright, through inspection, establishes the

existence of such a defect and that it is covered by this Limited Warranty. PowerBright will,

at its option, use new and / or reconditioned parts in performing warranty repair and building

replacement products. PowerBright reserves the right to use parts or products of original or

improved design in the repair or replacement. If PowerBright repairs or replaces a product, its

warranty continues for the remaining portion of the original Warranty Period or 90 days from

the date of the return shipment to the customer, whichever is greater. All replaced products

and all parts removed from repaired products become the property of PowerBright.

PowerBright covers both parts and labor necessary to repair the product, and return

shipment to the customer via a PowerBright selected non-expedited surface freight within the

contiguous United States and Canada. Alaska and Hawaii are excluded. Contact

PowerBright Customer Service for details on freight policy for return shipments outside of the

contiguous United States and Canada.

How do you get service? If your product requires troubleshooting or warranty service,

contact your dealer. If you are unable to contact your dealer, or the dealer is unable to

provide service, contact PowerBright directly at:

Toll Free: 1 866.295.6775

Website: www.EnergizerPower.com

under license by PowerBright. All other trademarks, brand names or product names are the property of

their respective owners and are not affiliated with Energizer or Bright Manufacturing LLC.

Energizer 8970600 Owner's manual

Brand: Energizer

Model: 8970600

Category: Battery chargers

Type: Owner's manual

Energizer 8970600

The charger has several safety features to help prevent accidents, including:

Reverse polarity protection
Overcharging protection
Short circuit protection
Overheating protection

It also has an adjustable charge rate, so you can choose the right setting for your battery. The charger is easy to use and comes with a detailed instruction manual.

Download PDF

report

Energizer 8970600 Owner's manual

Energizer 8970600 Owner's manual

Related papers

Other documents