Andersen 400 Series - Circle - 0004342 Operating instructions

Type
Operating instructions
Interior Hardwood Grilles
Andersen® Circle Windows
Weight of window and door
unit(s) and accessories will vary.
Use a reasonable number of
people with sufcient strength to
lift, carry, and install window and
door unit(s) and accessories.
Always use appropriate lifting
techniques.
Use of ladders and/or scaffolding and
working at elevated levels may be
hazardous. Follow equipment
manufacturer's instructions for safe
operation. Use extreme caution when
working around window and door
openings. Falling from opening may
result in personal injury or death.
Improper use of hand or
power tools could result in
personal injury and/or
product damage. Follow
equipment manufacturer's
instructions for safe
operation. Always wear
safety glasses.
For ease of installation and continued enjoyment of your Andersen® product, please read and follow this Instruction
Guide completely. You may direct any questions about this or other products to your local Andersen dealer, found
in the Yellow Pages under “Windows”, or call Andersen WindowCare® service center at 1-888-888-7020 Monday
through Friday, 7 a.m. to 7 p.m. Central Time and Saturday, 8 a.m. to 4 p.m. Central Time. Assembly and
installation of Andersen products is the sole responsibility of the architect, building owner, contractor and/or
consumer and Andersen has no responsibility in this regard. Thank you for choosing Andersen.
Interior Hardwood Grilles
for Andersen® Circle Windows
“Andersen” and “Andersen WindowCare” are registered trademarks of Andersen Corporation. All other marks where denoted are marks of Andersen Corporation.
©1998-2003 Andersen Corporation. All rights reserved. Instruction Guide 0004342 Revised 11/06/03
Parts Included
(1) Interior Hardwood Grille
(1) Installation Tool with Starter Tip
Grille Fasteners
Installation Tool
Fastener
Grille
Component Identication
1
2. Mark Grille Location
Place light pencil marks on Inside Glass Stop
where center of each vertical Grille Spoke meets
Inside Glass Stop. It is not necessary to mark
horizontal Grille Spokes because they are held in
place by the Transition Block or Optional Key Block.
Pencil Mark
1. Position Grille In Unit
Position Grille in unit so vertical Grille
Spokes are at 10 o'clock and 4 o'clock
positions. Vertical Grille Spokes have
routed end tips. Horizontal Grille Spokes
are mitered 45° to slide under Transition
Block or Optional Key Block.
Rotate Grille clockwise into proper
position.
Transition
Block
Optional
Key Block
Andersen® Circle Windows Interior Hardwood Grilles
2
Andersen® Circle Windows Interior Hardwood Grilles
3
3. Position Fasteners
Position Fasteners in alignment with pencil marks
between glass surface and Inside Glass Stop.
Insert only far enough to maintain position.
Place Fastener Installation Tool against glass and
carefully push Fasteners tightly against Inside
Glass Stop, keeping at side against glass at all
times.
Fastener
Installation Tool
4. Install Grille
Position Grille in unit so vertical Grille Spokes are at
10 o'clock and 4 o'clock positions. Rotate Grille
clockwise until vertical Grille Spokes come to rest
against Fasteners and horizontal Grille Spokes are
under Transition Block or Optional Key Block.
Lift vertical Grille Spokes gently, one at a time, up and
over Fastener, snapping them into place.
Rotate Clockwise
Grille
Glass
Inside
Glass
Stop
Fastener
Andersen® Circle Windows Interior Hardwood Grilles
2
Andersen® Circle Windows Interior Hardwood Grilles
3
Finishing, Cleaning, and Maintenance Instructions
DO NOT expose unnished wood to high moisture
conditions, excessive heat or humidity. Finish
interior wood surfaces immediately after
installation. Unnished wood surfaces will
discolor, deteriorate, and/or may bow and split.
INTERIOR FINISHING
Read and follow nishing manufacturer’s instructions
and warnings on each container of nish material for
priming, painting, staining, and varnishing.
CLEANING
To clean glass, grille can be removed by following the
instructions above.
MAINTENANCE
Immediately sand and renish any interior wood that
becomes stained or mildewed to prevent further
discoloration and/or damage. For further information,
contact your local Andersen dealer. Dealers can be
found in the Yellow Pages under Windows.
Rotate Counterclockwise
to remove grille
Lift vertical Grille Spokes carefully up and over
Fasteners in the counterclockwise direction. Continue
rotating Grille counterclockwise until horizontal Grille
Spokes clear Transition Block or Optional Key Block.
Grille Removal
5. Fastener Adjustment
If Grille appears loose, tension can be increased by
gently bending Fasteners toward Grille.
If Grille appears tight, release tension by gently bending
Fasteners toward Inside Glass Stop.
Grille
Glass
Inside
Glass
Stop
Fastener
To LoosenTo Tighten
Andersen® Circle Windows Interior Hardwood Grilles
4
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Andersen 400 Series - Circle - 0004342 Operating instructions

Type
Operating instructions

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI