Andersen 400 Series - Elliptical - 0005186 Operating instructions

Andersen
Brand
Andersen
Model
400 Series - Elliptical - 0005186
Type
Operating instructions

Andersen 400 Series - Elliptical - 0005186 allows for ease of installation and enjoyment of your Andersen product.

With this device, you can locate the Sill Fastener. The Interior arched Glass Stop has notched fastener locations. To determine the fastener location at sill, hold the Grille in the glass opening and use it as a template to lightly mark the center of the hub. Remove the temporary mark on the sill Glass Stop after installation.

You can apply Fasteners by pushing the Grille Tip Fastener point into the center of the notched area using the Fastener Installation Tool provided. Keep the Grille Tip Fastener tight against the glass.

Andersen 400 Series - Elliptical - 0005186 allows for ease of installation and enjoyment of your Andersen product.

With this device, you can locate the Sill Fastener. The Interior arched Glass Stop has notched fastener locations. To determine the fastener location at sill, hold the Grille in the glass opening and use it as a template to lightly mark the center of the hub. Remove the temporary mark on the sill Glass Stop after installation.

You can apply Fasteners by pushing the Grille Tip Fastener point into the center of the notched area using the Fastener Installation Tool provided. Keep the Grille Tip Fastener tight against the glass.

Weight of window and door
unit(s) and accessories will vary.
Use a reasonable number of
people with sufcient strength to
lift, carry, and install window and
door unit(s) and accessories.
Always use appropriate lifting
techniques.
Use of ladders and/or scaffolding and
working at elevated levels may be
hazardous. Follow equipment
manufacturer's instructions for safe
operation. Use extreme caution when
working around window and door
openings. Falling from opening may
result in personal injury or death.
Improper use of hand or
power tools could result in
personal injury and/or
product damage. Follow
equipment manufacturer's
instructions for safe
operation. Always wear
safety glasses.
For ease of installation and continued enjoyment of your Andersen® product, please read and follow this Instruction
Guide completely. You may direct any questions about this or other products to your local Andersen dealer, found
in the Yellow Pages under “Windows”, or call Andersen WindowCare® service center at 1-888-888-7020 Monday
through Friday, 7 a.m. to 7 p.m. Central Time and Saturday, 8 a.m. to 4 p.m. Central Time. Assembly and
installation of Andersen products is the sole responsibility of the architect, building owner, contractor and/or
consumer and Andersen has no responsibility in this regard. Thank you for choosing Andersen.
• Interior arched Glass Stop has notched fastener
locations. To determine fastener location at sill,
hold Grille in glass opening and use as a template
to lightly mark center of hub. Remove temporary
mark on sill Glass Stop after installation.
1. Locate Sill Fastener
Lightly Mark Center
Perma-Fit® Interior Grilles
for Andersen® 400 Series Elliptical Windows
“Andersen” and “Andersen WindowCare” are registered trademarks of Andersen Corporation. All other marks where denoted are marks of Andersen Corporation.
© 1995-2004 Andersen Corporation. All rights reserved. Instruction Guide 0005190 Revised 04/13/04
Perma-Fit® Interior Grilles
1
3. Install Grille
• Align Grille Tips with Grille Tip Fasteners. With
upward pressure, push Grille Tips onto Grille Tip
Fasteners and snap grille hub over Hub fastener.
4. Adjusting Fasteners
• If Grille t appears loose, tension can be
increased by slightly bending hub fastener toward
Grille. To decrease tension, gently bend hub
fastener towards Glass Stop.
2. Apply Fasteners
• Push Grille Tip Fastener point into center of
notched area using Fastener Installation Tool
provided. Keep Grille Tip Fastener tight against
glass.
• Push Hub Tip Fastener tip into center of location
mark using Fastener Installation Tool provided.
Keep Grille Tip Fastener tight against glass.
• Repeat procedure at each notch.
Fastener
Tight to Glass
and Glass Stop
Grille Fastener
Cross Section Detail
Cross Section Detail -
Hub Fastener
Cross Section Detail -
Grille Tip Fastener
Grille Removal
• Reverse procedure in Step 3 for removal of Grille.
Fastener
Tight to Glass
and Glass Stop
Clip
Glass Stop
Increase
Decrease
2
Perma-Fit® Interior Grilles
  • Page 1 1
  • Page 2 2

Andersen 400 Series - Elliptical - 0005186 Operating instructions

Andersen
Brand
Andersen
Model
400 Series - Elliptical - 0005186
Type
Operating instructions

Andersen 400 Series - Elliptical - 0005186 allows for ease of installation and enjoyment of your Andersen product.

With this device, you can locate the Sill Fastener. The Interior arched Glass Stop has notched fastener locations. To determine the fastener location at sill, hold the Grille in the glass opening and use it as a template to lightly mark the center of the hub. Remove the temporary mark on the sill Glass Stop after installation.

You can apply Fasteners by pushing the Grille Tip Fastener point into the center of the notched area using the Fastener Installation Tool provided. Keep the Grille Tip Fastener tight against the glass.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers