Gefen EXT-HD2IRS-LAN-RX User manual

Brand: Gefen

Model: EXT-HD2IRS-LAN-RX

Category: AV extenders

Type: User manual

This manual is also suitable for

EXT-HD2IRS-LAN-TX

Audio

Embedder

3GSDI

EXT-HD2IRS-LAN-TX

EXT-HD2IRS-LAN-RX

User Manual

HD over IP

w/ RS-232 and 2-way IR

*Preferred

Release A2

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this product near water.

6. Clean only with a dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s

instructions.

8. Do not install or place this product near any heat sources such as radiators, heat

registers, stoves, or other apparatus (including ampliers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized

plug has two blades with one wider than the other. A grounding type plug has two

blades and a third grounding prong. The wide blade or the third prong are provided for

your safety. If the provided plug does not t into your outlet, consult an electrician for

replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs,

convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories specied by the manufacturer.

12. To reduce the risk of electric shock and/or damage to this product, never handle or

touch this unit or power cord if your hands are wet or damp. Do not expose this

product to rain or moisture.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualied service personnel. Servicing is required when the

apparatus has been damaged in any way, such as power-supply cord or plug is

damaged, liquid has been spilled or objects have fallen into the apparatus,

the apparatus has been exposed to rain or moisture, does not operate normally,

or has been dropped.

15. Batteries that may be included with this product and/or accessories should never be

exposed to open ame or excessive heat. Always dispose of used batteries

according to the instructions.

Important Safety Instructions

iii

Gefen warrants the equipment it manufactures to be free from defects in material and

workmanship.

If equipment fails because of such defects and Gefen is notied within two (2) years from

the date of shipment, Gefen will, at its option, repair or replace the equipment, provided

that the equipment has not been subjected to mechanical, electrical, or other abuse or

modications. Equipment that fails under conditions other than those covered will be

repaired at the current price of parts and labor in effect at the time of repair. Such repairs

are warranted for ninety (90) days from the day of reshipment to the Buyer.

This warranty is in lieu of all other warranties expressed or implied, including without

limitation, any implied warranty or merchantability or tness for any particular purpose, all of

which are expressly disclaimed.

1. Proof of sale may be required in order to claim warranty.

2. Customers outside the US are responsible for shipping charges to and from Gefen.

3. Copper cables are limited to a 30 day warranty and cables must be in their original

condition.

The information in this manual has been carefully checked and is believed to be accurate.

However, Gefen assumes no responsibility for any inaccuracies that may be contained

in this manual. In no event will Gefen be liable for direct, indirect, special, incidental, or

consequential damages resulting from any defect or omission in this manual, even if

advised of the possibility of such damages. The technical information contained herein

regarding the features and specications is subject to change without notice.

For the latest warranty coverage information, refer to the Warranty and Return Policy under

the Support section of the Gefen Web site at www.gefen.com.

Warranty Information

Technical Support

(818) 772-9100 (800) 545-6900

8:00 AM to 5:00 PM Monday - Friday, Pacic Time

Fax

(818) 772-9120

[email protected]

Web

http://www.gefen.com

Mailing Address

Gefen, LLC

c/o Customer Service

20600 Nordhoff St.

Chatsworth, CA 91311

Product Registration

Contacting Gefen Technical Support

Operating Notes

• The Sender and Receiver for the HD over IP w/ RS-232 and 2-way IR are sold

separately. This User Manual describes how to connect and operate both Sender

and Receiver units.

• This product requires a Gigabit switch that supports 8k jumbo frames in order for

multicast mode to function correctly. If the LAN is not exclusively dedicated to this

product, then a managed switch is highly recommended.

• CAT-5e or CAT-6 cables should not exceed 330 feet (100 meters) between the

Sender / Receiver unit and the network.

• By default, all Sender and Receiver units are set to channel 0.

HD over IP w/ RS-232 and 2-way IR is a trademark of Gefen, LLC.

All trademarks are the property of their respective owners.

Gefen, LLC reserves the right to make changes in the hardware, packaging, and any accompanying documentation

without prior written notice.

This product uses UL or CE listed power supplies.

Features

• Extends HDMI, RS-232, and bi-directional IR over IP, using a Gigabit Local Network

• Supports resolutions up to 1080p Full HD and 1920 x 1200 (WUXGA)

• Supported HDMI Features:

► HDCP

► Deep Color

► LPCM 7.1 audio, Dolby® TrueHD, and DTS-HD Master Audio™

► Lip-Sync pass-through

• Built-in web interface facilitates intuitive set up and operation

• Any of the Senders within a network can be accessed by any Receiver unit via a web

browser on a mobile device or computer, or by using the Gefen KVM/Video over IP

Keyboard Switching Controller software (available for download at www.gefen.com)

• Supports a total of just over 65,000 Sender and Receiver units, depending on the

network bandwidth and number of ports on your network switch

• Mode Selector function in web interface for sharpness or motion optimization of image

• Versatile IR In/Ext ports work with powered Gefen IR extenders and electrical IR from

automation control devices

• Field-upgradable rmware via web server interface

• Locking power supply connectors

• RS-232 3.5mm mini-stereo-jack-to-DB-9 adaptors included

• Surface mountable

1080P

Features and Packing List

vii

Packing List

The Sender and Receiver for the HD over IP w/ RS-232 and 2-way IR are sold separately.

The packing lists will vary, slightly, depending upon which unit was purchased. If any of

these items are not present in the box when you rst open it, immediately contact your

dealer or Gefen.

Sender Package (EXT-HD2IRS-LAN-TX)

• 1 x HD over IP w/ RS-232 and 2-way IR (Sender unit)

• 1 x 6 ft. locking HDMI cable (M-M)

• 1 x 3.5 mini-stereo-to-DB-9 cable adapter (M-F)

• 1 x IR emitter

• 1 x 5V DC locking power supply

• 1 x Quick-Start Guide

Receiver Package (EXT-HD2IRS-LAN-RX)

• 1 x HD over IP w/ RS-232 and 2-way IR (Receiver unit)

• 1 x 3.5 mini-stereo-to-DB-9 cable adapter (M-M)

• 1 x IR extender

• 1 x 5V DC locking power supply

• 1 x Quick-Start Guide

Features and Packing List

viii

Table of Contents

1 Getting Started

Introduction............................................................................................................ 2

Sender Unit ................................................................................................... 2

Receiver Unit ................................................................................................. 4

Installation ............................................................................................................. 6

Using a Direct Connection ............................................................................ 6

Local Area Network (LAN) Connection ......................................................... 7

Additional Connections ................................................................................. 8

Sample Wiring Diagram ................................................................................ 9

2 Basic Operation

Bidirectional IR Control........................................................................................ 12

Controlling the Source from the Viewing Location ...................................... 12

Controlling the Display from the Source Location ....................................... 13

Controlling the Source / Display from Different Locations ........................... 14

Displaying the IP Address ................................................................................... 15

Web Interface ...................................................................................................... 16

Viewing System Settings ............................................................................. 18

Setting the Password .................................................................................. 19

Setting the Video Channel .......................................................................... 20

Setting the IP Mode ..................................................................................... 22

Setting the IP Address ................................................................................ 24

Enabling or Disabling Video over IP ............................................................ 25

Enabling or Disabling HDCP ....................................................................... 26

Picture Quality Mode ................................................................................... 27

EDID Management .............................................................................................. 28

Using the Internal EDID .............................................................................. 28

Using the Downstream EDID ...................................................................... 29

Unicast and Multicast Modes .............................................................................. 30

Conguring Unicast Mode ........................................................................... 30

Switching between Sender units in Unicast mode ...................................... 32

Conguring Multicast Mode ......................................................................... 35

Using RS-232 ...................................................................................................... 37

RS-232 under Unicast Mode ....................................................................... 39

RS-232 under Multicast Mode ..................................................................... 39

Resetting a Unit ................................................................................................... 40

Table of Contents

3 Appendix

Upgrading the Firmware ...................................................................................... 44

Web Interface Summary ...................................................................................... 47

Network tab ................................................................................................. 48

Functions tab ............................................................................................... 50

System tab - Version Information ................................................................ 52

System tab - Update Firmware ................................................................... 54

System tab - Command Mode .................................................................... 55

Manual Reset Procedure..................................................................................... 56

Surface Mounting Instructions ............................................................................. 57

Network Cable Diagram ...................................................................................... 58

Specications ...................................................................................................... 59

Index.................................................................................................................... 60