Foxconn AT-7300 User manual

Brand: Foxconn

Model: AT-7300

Category: PC/workstation barebones

Type: User manual

This manual is also suitable for

AT-7500

NanoPC

User’s Manual

Before using this product, please read the below safety notice carefully, this will help to

extend the product’s lifecycle, and work normally.

■ WhenNanoPCisworking,pleasemakesureitsventilationsystemisworking.

■

Thepoweradapterisdissipatingheatduringnormaluse,pleasebesurenottocover

 itandkeepitawayfromyourbodytopreventdiscomfortorinjurybyheatexposure.

■ Pleaseusethepoweradapterthatcomeswiththeproduct’spackage,wrongpower

 adaptermaydamageyourdevice.

■ MakesurealltheperipheralsareproperlyconnectedbeforeusingNanoPC.

■ Thisproductshouldonlybeusedinanenvironmentwithambienttemperatures

 between0°Cand40°C.

■ Alwaysshutdownthecomputerbeforeinstallingoruninstallingtheperipheralwhich

does not support hot plug.

■ Disconnectallperipheralsbeforeservicingordisassemblingthisequipment.

■ Pleasedonotdisassemblethisproductbyyourself,anydisassemblynotapproved

 bytheoriginalmanufacturermayresultinmalfunction,andvoidwarranty.

■ Riskofexplosionifbatteryisreplacedbyanincorrecttype,pleasedisposeofused

batteries according to the instructions.

AUTIO

Safety Notice:

Trademark:

 Alltrademarksarethepropertyoftheirrespectiveowners.

Version:

 User’sManualV1.0forNanoPC.

Symbol description:

 Note: ReferstoimportantinformationthatcanhelpyoutouseNanoPCbetter,and

 tellsyouhowtoavoidproblems.

 Caution: Indicatingapotentialriskofhardwaredamageorphysicalinjurymayexist.

 WEEE:

The use of this symbol indicates that this product may not be treated as household

waste.Byensuringthisproductisdisposedofcorrectly,youwillhelppreventpotential

negativeconsequencesfortheenvironmentandhumanhealth,whichcouldotherwise

be caused by inappropriate waste handling of this product. For more detailed informa-

tionaboutrecyclingofthisproduct,pleasecontactyourlocalcityofce,yourhouse-

holdwastedisposalserviceortheshopwhereyoupurchasedthisproduct.

©Allrightsreserved.

Alltradenamesareregisteredtrademarksofrespectivemanufacturerslisted.

Allimagesareforreferenceonly,pleaserefertothephysicalproductforspecicfeatures.

AUTIO

Introduction

1-1FrontSideView ...................................................................................................... 2

1-2BackSideView ....................................................................................................... 4

Placement and connecting

2-1PlacementofNanoPC ........................................................................................... 7

InSeatBase ............................................................................................................. 7

On the desk .............................................................................................................. 7

2-2ConnectionofNanoPC .......................................................................................... 8

Connectdisplay ........................................................................................................ 8

ConnectUSBdevices............................................................................................... 9

Connectnetworkcable ............................................................................................. 9

Connectpowercord ............................................................................................... 10

BIOS Setup

EnterBIOSSetup ....................................................................................................... 12

Main ............................................................................................................................ 13

Advanced .................................................................................................................... 14

Miscellaneous ......................................................................................................... 15

IntegratedPeripherals ............................................................................................ 16

SATAConguration ................................................................................................ 17

Power .......................................................................................................................... 19

TABLE OF CONTENTS

Package Contents

WeDONOTguaranteeitisincompliancewiththeSafetyCerticatesifyouaddonan

extensioncabletoNanoPCUSBFlashDiskinthepackage.

NanoPC SeatBase

Screws,MiniPCIeHalfCardSup-

portBracket,MagnetRubberFoot

PowerAdapter PowerCord EasyGuide

USBFlashDisk DVI-VGAAdapter

Security ....................................................................................................................... 20

BootOptions ................................................................................................................ 21

Save&Exit ................................................................................................................. 23

Install OS

4-1InstallWindows7/8 ............................................................................................... 26

4-2InstallDrivers ........................................................................................................ 30

Utility

FoxWINFLASH .......................................................................................................... 32

1.LocalUpdate ...................................................................................................... 32

2.About&Help....................................................................................................... 34

■FrontSideView

■BackSideView

Introduction

2 3

INTRODUCTION INTRODUCTION

1 PowerbuttonwithPowerindicatorLED

PresstoturnyourNanoPConoroff,theLEDcanindicateyoursystem

states.

2 Speaker

USB3.0port

ThisUSBportsupportstheUSB3.0/2.0/1.0specication.Usethisportfor

USBdevicessuchaskeyboard,mouse,USBprinter,USBashdrivesand

harddiskdrives,etc.

AstoWindows7system,youneedtoinstalltheUSB3.0driverinNanoPC

USBDiskbeforeusingit.

Multi-Functioncardreader

ThismemorycardreadersupportsSD/SDHC/SDXC/MS/MSPro/MMC

memorycardsusedindeviceslikedigitalcameras,mobilephones,Media

players and so on.

Microphone/SPDIFinport

Connectstoamicrophoneorplaybackdeviceswithopticalconnectors

(3.5mmjack).

SPDIFfunctionrequiresadditionaladapterandadaptercable.

Headphone

Connectstoaheadphone.

7 Kensington lock

AttachaKensingtonsecuritysystemoracompatiblesecuritylocktosecure

yourNanoPCinplace.

1-1 Front Side View

4 5

INTRODUCTION INTRODUCTION

1 USB2.0port

ThisUSBportsupportstheUSB2.0/1.0specication.UsethisportforUSB

devicessuchaskeyboard,mouse,USBprinter,USBashdrivesandhard

diskdrives,etc.

USB3.0port

ThisUSBportsupportstheUSB3.0/2.0/1.0specication.Usethisportfor

USBdevicessuchaskeyboard,mouse,USBprinter,USBashdrivesand

harddiskdrives,etc.

AstoWindows7system,youneedtoinstalltheUSB3.0driverinNanoPC

USBDiskbeforeusingit.

DVI

DVIport

ConnectmonitororTVthatusesDVIconnectortothisport.

ByusingtheDVItoVGAadapterthatcomeswithyourproduct,youcanalso

connectaVGA-compatibledevicessuchasamonitororprojector.

HDMI

HDMIport

TheHDMI(High-DenitionMultimediaInterface)portsupportsFull-HD

displaydevices.

ConnectmonitororTVthatusesHDMIconnectortothisport.

RJ-45LANport

Supports10/100/1000Mb/sEthernetnetwork.

ConnectnetworkcabletoaccessInternet.

Lineout/SPDIFoutport

Connectstopoweredanalogspeakersorrecordingdeviceswithoptical

connectors(3.5mmjack).

SPDIFfunctionrequiresadditionaladapterandadaptercable.

Powerinputport

Connectpowercordthatcomewithyourproduct.

1-2 Back Side View

PLACEMENTANDCONNECTING

2-1 Placement of NanoPC

In Seat Base

 PlaceyourNanoPCintothegrooveoftheSeatBase.

On the desk

 FityourNanoPCwithMagnetRubberFoot,andputitonthetabletopdirectly.

Placement

and

connecting

■PlacementofNanoPC

■ConnectionofNanoPC

8 9

PLACEMENTANDCONNECTING PLACEMENTANDCONNECTING

Connect USB devices

 ConnectUSBdevicestotheUSBports,forexample,mouse,keyboarddevices.

 AstoWindows7system,youneedtoinstalltheUSB3.0driverinNanoPCUSBdiskbeforeusingthe

 USB3.0ports.

Connect network cable

 ConnectoneendofanetworkcabletotheRJ-45LANport,andtheotherendtoahubor

switch.

2-2 Connection of NanoPC

Connect display

ConnectadisplayorTVthathasHDMIportorVGAporttoyourNanoPC.

 YoucanconnectaVGAdisplaytotheDVIportbyusingtheDVI-VGAadapter.

 PleaseusethecustomizedDVI-VGAAdapterthatcomeswithyourNanoPCtogeta

 higherresolutiononyourVGAdisplay.

PLACEMENTANDCONNECTING

Connect power cord

 ConnectthepoweradaptertothepowerinputportoftheNanoPC,andthenpressthepowerbuttonto

start it.

Thepoweradapterisdissipatingheatduringnormaluse,pleasedonotcoveritand

keepitawayfromyourbodytopreventinjuryfromheatexposure.

AUTIO

■EnterBIOSSetup

■Main

■Advanced

■Power

■Security

■BootOptions

■Save&Exit

BIOS Setup

12 13

BIOSSETUP BIOSSETUP

Main

Main Advanced Power Security BootOptions Save & Exit

System BIOS

Project Version C25F1D17

Build Date 11/23/2012

EC Version 12.F1.05

Processor

Intel(R) Core(TM) i5-3317U CP

Core Frequency 1.70 GHz

Count 2

Chipset

Intel PCH SKU Name HM76

System Memory

Memory Frequency 1333 Mhz

System Memory Size 4096 MB (DDR3)

System Date [Wed 11/23/2012]

System Time [16:06:12]

Access Level Administrator

↑ ↓→ ←: Move

Enter: Select

+/-: Change Opt.

ESC: Exit

F1: General Help

F2: Previous Values

F3: Optimized Defaults

F4: Save & Exit Setup

F7: Load User-defined Defaults

F8: Save as User-defined

Set the Date. Use Tab to

switch between Date elements.

Main

►SystemDate

<weekday><month><date> <year> format.

 Day—weekdayfromSun.toSat.,thismessageisautomaticallydisplayedbyBIOS(ReadOnly).

 Month—monthfrom1to12.

 Date—datefrom1to31.

 Year—year,setupbyusers.

 Use[ENTER],[TAB]or[SHIFT-TAB]toselectaeld.Use[+]or[-]toinputthevalue.

►SystemTime

 Thisitemallowsyoutocongurethedesiredtime.Use[ENTER],[TAB]or[SHIFT-TAB]toselecta

 eld.Use[+]or[-]toinputthevalue.

 Thethreeeldsofthesettingare<hour>:<minute>:<second>respectively.

►AccessLevel

 Itdisplaysyourcurrentaccesslevel.Ifyouentersystemwithauserpassword,itwilldisplay“User”.If

Enter BIOS Setup

TheBIOSisthecommunicationbridgebetweenhardwareandsoftware,correctlysettinguptheBIOSpa-

rametersiscriticaltomaintainoptimalsystemperformance.Poweronthecomputer,whenthemessage

“Press<Del>toentersetup.Press<F11>toenterbootmenu.”

appearsatthebottomofthescreen,youcanpress<Del>keytoenterSetup.

Usethearrowright/leftkeystoselectaspecicfunctionandgotothesubmenu.Eachfunctionisex-

plainedbelow:

Main

 Itdisplaysthebasicsystemconguration,suchasCPUName,memorysize,systemdate,timeand

 soon.Theyallcanbeviewedorsetupthroughthismenu.

Advanced

 Theadvancedsystemfeaturescanbesetupthroughthismenu.

Power

AlltheitemsrelatedwithGreenfunctionfeaturescanbesetupthroughthismenu.

Security

 TheAdministrator/Userpasswordcanbesetupthroughthismenutopreventunauthorizeduseof

 yourcomputer.Ifyousetapassword,thesystemwillaskyoutokeyincorrectpasswordbeforeboot

 oraccesstoSetup.

BootOptions

 Bootfeaturescanbesetupthroughthismenu.Youcansetthebootdevicepriorityandenable“Quiet

 Boot”featurehere.

Save&Exit

 Theoptimalperformancesettingscanbeloadedthroughthismenu.However,itmayofferbetter

 performanceinsomeways(suchaslessI/Ocards,lessmemory...etc.),still,itmaycauseproblem

 ifyouhavemorememoryorI/Ocardsinstalled.Itmeans,ifyoursystemloadingisheavy,setto 

 optimaldefaultmaysometimescomeoutanunstablesystem.WhatyouneednowistoadjustBIOS

 settingonebyone,trialanderror,tondoutthebestsettingforyourcurrentsystem.Youalsocan

 saveordiscardthechangesandexitBIOSsetuphere.

WedonotsuggestthatyouchangethedefaultvaluesintheBIOSSetup,andweshall

not be responsible for any damage which resulted from the change you made.

14 15

BIOSSETUP BIOSSETUP

no password is set or you enter system with administrator password, this item will display

 “Administrator”.

Advanced

Main Advanced Power Security BootOptions Save & Exit

▶ Miscellaneous

▶ Integrated Periperals

▶ SATA configuration

↑ ↓→ ←: Move

Enter: Select

+/-: Change Opt.

ESC: Exit

F1: General Help

F2: Previous Values

F3: Optimized Defaults

F4: Save & Exit Setup

F7: Load User-defined Defaults

F8: Save as User-defined

Miscellaneous

Advanced

► Miscellaneous/IntegratedPeriperals/SATAconguration

 Press<Enter>togotorelativesubmenu.

Miscellaneous

Main Advanced Power Security BootOptions Save & Exit

Bootup Num-Lock [off]

↑ ↓→ ←: Move

Enter: Select

+/-: Change Opt.

ESC: Exit

F1: General Help

F2: Previous Values

F3: Optimized Defaults

F4: Save & Exit Setup

F7: Load User-defined Defaults

F8: Save as User-defined

Select the keyboard NumLock

state

Advanced

►BootupNum-Lock

 ThisitemdenesifthekeyboardNumLockkeyisactivewhenyoursystemisstarted.Theavailable

 settingsare:OnandOff(default).

16 17

BIOSSETUP BIOSSETUP

Integrated Peripherals

Main Advanced Power Security BootOptions Save & Exit

PCH Azalia Configuration

Azalia [Enabled]

CIR Controller Configuration

CIR Controller [Disabled]

↑ ↓→ ←: Move

Enter: Select

+/-: Change Opt.

ESC: Exit

F1: General Help

F2: Previous Values

F3: Optimized Defaults

F4: Save & Exit Setup

F7: Load User-defined Defaults

F8: Save as User-defined

Control Detection of the

Azalia device.

Disabled = Azalia will be

unconditionally disabled

Enabled = Azalia will be

unconditionally Enabled

Advanced

►Azalia

 ThisitemisusedtocontrolthedetectionofAzaliadevice.

►CIRController

 ThisitemisusedtoenableordisabletheCIRcontroller.

SATA Conguration

Main Advanced Power Security BootOptions Save & Exit

SATA Controller(s) [Enabled]

SATA Mode Selection [AHCI]

Port 0 [Enabled]

Port 1 [Enabled]

Intel(R) Rapid Start Technology

Intel(R) Rapid Start Technology [Disabled]

↑ ↓→ ←: Move

Enter: Select

+/-: Change Opt.

ESC: Exit

F1: General Help

F2: Previous Values

F3: Optimized Defaults

F4: Save & Exit Setup

F7: Load User-defined Defaults

F8: Save as User-defined

Enable or disable SATA Device.

Advanced

►SATAController(s)

 [Disabled]:DisableSATAController.

 [Enabled]:EnableSATAController.

►SATAModeSelection

 ThisitemisusedtosettheoperationmodeofyourSATAports.

 [IDE]-ThiscongurestheSATAportstosupportIDEmode.

 [AHCI]-TheAdvancedHostControllerInterface(AHCI)specicationdescribestheregister

 levelinterfaceforaHostControllerforSerialATA.Thespecicationincludesadescriptionofthe

 hardware/softwareinterfacebetweensystemsoftwareandthehostcontrollerhardware.AHCI

 providesmoreadvancedfeaturesincludingSATAfeatures,butsomeSATAdrivesmaynotsupport

 AHCI,unlesstheyarelabeledwithAHCIsupportinitsspecication.

 IfyourmotherboardsupportingAHCI,andyouhaveaSATAdevice,whichalsosupportsAHCI,then

18 19

BIOSSETUP BIOSSETUP

 youcanselectIDEoptiontohavefairperformance,oryoucanselectAHCItogetitsbest

performance.

►Port0/Port1

 ThisitemisusedtoenableordisableSATAport0/1.

►Intel(R)RapidStartTechnology

 ThisitemisusedtoenableordisabletheIntel(R)RapidStartTechnology.

Power

Main Advanced Power Security BootOptions Save & Exit

Restore On AC Power Loss [Last State]

Deep Sleep Support [Enabled]

↑ ↓→ ←: Move

Enter: Select

+/-: Change Opt.

ESC: Exit

F1: General Help

F2: Previous Values

F3: Optimized Defaults

F4: Save & Exit Setup

F7: Load User-defined Defaults

F8: Save as User-defined

Set the restore on AC power

loss function.

Power

►RestoreonACPowerLoss

ThisitemisusedtosetwhichstatethePCwilltakewithwhenitresumesafteranACpowerloss.

►DeepSleepSupport

 ThisitemisusedtoenableordisableDeepSleepSupportfunction.Whenenteringdeepsleepmode

 system(S4/S5)onlycanwakeupfrompowerbutton.

►LanWakeup

 ThisitemisusedtoenableordisableLANwakeupfunction.itappearsonlywhenthe“DeepSleep

 Support”isdisabled.

20 21

BIOSSETUP BIOSSETUP

Security

Main Advanced Power Security BootOptions Save & Exit

Administrator Password Status Installed

User Password Status Not Installed

Change Supervisor Password

Change User Password

Security option [Setup]

ME Flash Write Protect [Enabled]

↑ ↓→ ←: Move

Enter: Select

+/-: Change Opt.

ESC: Exit

F1: General Help

F2: Previous Values

F3: Optimized Defaults

F4: Save & Exit Setup

F7: Load User-defined Defaults

F8: Save as User-defined

Valid Keys:

(1)a-z (A-Z)

(2)0~9

(3)11 special keys:-=[];,./

(4)key pad:0-9 support and 5

special keys

Security

►ChangeSupervisorPassword

Thisitemisusedtoinstallorchangesupervisorpassword.

► ChangeUserPassword

This item is used to install or change user password.

 OnlywhenthereexistsanAdministratorpassword,thenthissettingcanbeactivated.

►Securityoption

 ToprotecttheBIOSfrombeingchangedbytheunauthorizedusers,thereisasecurityoptionprovided

foryourchoice.OnlywhenthereexistsanAdministratorpassword,thenthissettingcanbeactivated.

 [setup]:ApasswordwillberequiredtoentertheBIOS.(Onlycheckpasswordwhenentersetup)

 [Always]:ApasswordwillberequiredtoenterboththesystemandBIOS.(Alwayscheckpassword)

►MEFlashWriteProtect

ToprotecttheMEBIOS,thereisaMEBIOSwrite-protectionmechanismprovidedtopreventBIOS

FLASHtoolbeingimproperlyusedtoupdateMEBIOS.

BootOptions

Main Advanced Power Security BootOptions Save & Exit

Launch CSM [Enabled]

Launch PXE OpROM policy [Do not launch]

FIXED BOOT ORDER Priorities

1st Boot Device [Hard Disk]

2nd Boot Device [CD&DVD]

3rd Boot Device [Removable Device]

4th Boot Device [LAN]

▶ Hard Disk Drive Priority [Press Enter]

▶ Optical Disk Drive Priority [Press Enter]

▶ Removable Device Priority [Press Enter]

▶ Network Device Priority [Press Enter]

Quiet Boot [Disabled]

Boot Menu [Enabled]

↑ ↓→ ←: Move

Enter: Select

+/-: Change Opt.

ESC: Exit

F1: General Help

F2: Previous Values

F3: Optimized Defaults

F4: Save & Exit Setup

F7: Load User-defined Defaults

F8: Save as User-defined

This option controls if CSM

will be launched

BootOption

►LaunchCSM

 ThisitemcontrolsifCSMwillbelaunched.

 WARNING:Thisoptionisforadvancedusers.

►LaunchPXEOpROMpolicy

 ThisitemcontrolstheexecutionofLegacyPXEOpROM.

►1st/2nd/3rd/4thBootDevice

These items are used to set the system boot order.

►HardDiskDrivesBBSPriorities/OpticalDiskDriveBBSPriorities/RemovableDeviceBBSPriorities/

 NETWORKDeviceBBSPriorities

 Press<Enter>togotoitssubmenu.Usethisitemstospecifythebootdeviceprioritysequenceofthe

 detecteddevices.

►QuietBoot

 Thisitemisusedtoenable/disablethequietboot.

22 23

BIOSSETUP BIOSSETUP

 [Disabled]:DisplaysthenormalPOSTmessages.

 [Enabled]:DisplaysOEMcustomerlogoinsteadofPOSTmessages.

►BootMenu

This item is used to enable or disable boot menu.

Save & Exit

Main Advanced Power Security BootOptions Save & Exit

Save Changes and Exit

Discard Changes and Exit

Save Changes

Discard Changes

Load Default Values

Save as User Default Values

Load User Default Values

↑ ↓→ ←: Move

Enter: Select

+/-: Change Opt.

ESC: Exit

F1: General Help

F2: Previous Values

F3: Optimized Defaults

F4: Save & Exit Setup

F7: Load User-defined Defaults

F8: Save as User-defined

Exit system setup after saving

the changes.

Save & Exit

►SaveChangesandExit

 Ifyouselectthisoptionandpress<Enter>,amessagewillbedisplayedinthescreen.

 Select[Yes]tosaveyourchangesandexit,select[No]or<ESC>toreturntothemainmenu.

►DiscardChangesandExit

 Ifyouselectthisoptionandpress<Enter>,amessagewillbedisplayedinthescreen.

 Select[Yes]toexitsetuputilitywithoutsavingyourmodications,select[No]or<ESC>toreturnto

the menu.

►SaveChanges

 Ifyouselectthisoptionandpress<Enter>,amessagewillbedisplayedinthecenterofthescreen.

 Select[Yes]tosaveyourchanges,select[No]or<ESC>toreturntothemenu.

►DiscardChanges

 Ifyouselectthisoptionandpress<Enter>,amessagewillbedisplayedinthecenterofthescreen.

 Select[Yes]todiscardyourmodications,select[No]or<ESC>toreturntothemenu.

►LoadDefaultValues

BIOSSETUP

■InstallWindows7/8

■InstallDrivers

Install OS

Optimal defaults are the best settings of this motherboard.

 AlwaysloadtheOptimaldefaultsafterupdatingtheBIOSorafterclearingtheCMOSvalues.

 SelectthisoptionandpressEnter,itwillpopoutadialogueboxtoletyouloadthedefaults.Select

 <Yes>andthenpress<Enter>toloadthedefaults.Select<No>andpress<Enter>,itwillnotload.

 Bythisdefault,BIOShavesettheoptimalperformanceparametersofsystemtoimprovetheperfor-

mances of system components. But if the optimal performance parameters to be set cannot be sup-

 portedbyyourhardwaredevices(forexample,toomanyexpansioncardswereinstalled),thesystem

might fail to work.

►SaveasUserDefaultValues

 Ifyouselectthisoptionandpress<Enter>,amessagewillbedisplayedinthescreen.

 Select[Yes]tosavethechangesdonesofarasuserdefaults,select[No]or<ESC>toreturntothe

menu.

►LoadUserDefaultValues

 Ifyouselectthisoptionandpress<Enter>,amessagewillbedisplayedinthescreen.

 Select[Yes]torestore/loadtheuserdefaultstoallthesetupoptions,select[No]or<ESC>toreturnto

the menu.

26 27

INSTALLOS INSTALLOS

Whatkindsofhardwareandsoftwareyouneedhere:

1.Windows7/8InstallUSBDisk/USBDVD-ROMdriveandWindows7/8InstallCD(Otherpurchase)

2. NanoPCUSBFlashDisk(Inthispackage)

Windows7(32-bit/64-bit)andWindows8(32-bit)can’tbeinstalledwhen“LaunchCSM”is

setto“Disabled”intheBIOSsetup.

4-1 Install Windows 7/8

1. ConnecttheWindows7/8InstallUSBDisk(orUSBDVD-ROMdrive)tooneUSBportofNanoPC.

2. Presspoweronbuttontoturnonyourcomputer.

3. PuttheWindows7/8InstallCDintotheUSBDVD-ROMdriveifyouusetheUSBDVD-ROMdrive.

4. ComputerwillchoosethebootdevicebyBIOSdefaultandstartloadingthelesforinstallingtheOS.

5. Whentheinstallationwindowspopup,settherelateditemsandclick“Next”tocontinue,thenclick

 “Installnow”buttontostartthesetup.

6. Whenthelicensetermsappear,chooseacceptandclick“Next”tocontinue.

7. Itwillthenaskyoutoselecttheinstallationtype.Click“Custom(advanced)”toinstallanewcopyof

 Windows.

Pleasepress<Del>keytoenterBIOSSetupifyouwanttochangetherstbootdevice

forinstallingtheOS.

8. Thesetupwilldisplaytheharddiskpartitions(160GB,inthisexample)ofyoursystem.Ifthere 

 wereothersystems(suchasLinux)installedpreviously,youneedselectthemandclick“Driveoptions

 (advanced)”todeletethem.Whenallpartitionsareclean,setupwilldisplaythebiggestsizeofyour

 harddrive.

28 29

INSTALLOS INSTALLOS

9. Intheharddisksizescreen,youcanclickthe“new”buttontocreatepartitionsasyouneed.

 Inthisexamplewearecreatinga70GBpartitiontoinstallWindows.Makeyourmodicationsand

 click“Apply”.

 ToensurethatallWindowsfeaturesworkcorrectly,Windowsmightcreateadditionalpartitionsfor

 systemles.Soyouwillseea100MBpartitionreservedbysystemafteryoucreateapartition.Select

 the70GBpartitionandclick“Next”tocontinue.

10.ThesetupprogramwillthenstarttoinstallWindows7/8onyourharddisk.Duringtheinstallation,

 yourcomputerwillrestartseveraltimes.

INSTALLOS

11.Whentheinstallationiscomplete,setupwillprepareyourcomputerforit’srstuse.Youcanthen

follow the steps to select system settings, create an account, set a password...etc, until the whole

process is completed.

4-2 Install Drivers

1. WhentheWindows7/8iscompletelyinstalled,youhavetoinstallthenecessarydriversbeforeusing

 theNanoPC.ConnecttheNanoPCUSBFlashDisktoyoursystem.

2. Waitingforafewseconds,themainmenuwillbedisplayedonthescreen.

3. Usetheseoptionstoinstallallthedriversforyoursystem.Youmustclick"IntelChipsetDriver"to

 installitrst.Afterthat,youcanclick”OneClickSetup”andthenchoosetheitemsyouwanttoinstall,

 oryoucanclickoneachindividualdrivertoinstallitmanually.

4. Afterinstallingallthedrivers,youneedtorestartyourNanoPC,thenyoucanstartusingit.

■FoxWINFLASH

Utility

32 33

UTILITY UTILITY

Fox WINFLASH

FoxWINFLASHisausefulutilitytobackupandupdateyoursystemBIOS.

SupportingOperatingSystems:

■ Windows7(32-bit/64-bit)

■ Windows8(32-bit/64-bit)

1. Local Update

1-1LocalUpdate-BIOSInformation

 ThispageletsyouknowyoursystemBIOSinformation.

Note:BIOSSize32Mb=32Mbit=4MByte

  BIOSSize16Mb=16Mbit=2MByte

Pleaserefertothephysicalmotherboardfordetails.

Toolbar

ShowcurrentBIOS

information

Minimum

Exit

1-2LocalUpdate-BackupBIOS

 ThispagecanbackupyoursystemBIOS.Youcanclick“BackupBIOS”,andkeyinalename,then

 click“Save”tonishthebackupoperation.Theextensionofthisbackupleis“.ROM”forAMIBIOS.

 Makesureyoucanrememberthelenametogetherwiththedirectorywhichitisstored,prevented

 thatyoumayneedthemtorecoveryourBIOSlater.

1-3LocalUpdate-UpdateBIOS

 ThispagehelpsyoutoupdateyourBIOSfromalocalle.Afterclick“UpdateBIOS”,Analert

 messagewillbedisplayedtoensureifyoureallywanttocontinue,click“Yes”toconrm.Asetup

 wizardwillguideyoutoloadalocalBIOSletonishtheoperation.Youmustrememberfromwhich

 directorytoloadyournewBIOSle(withanextensionof“.ROM”forAMIBIOS)beforethesetup

 wizardstarts.

KeyinaBIOSname

ClicktoSave

Page is loading ...

Foxconn AT-7300 User manual

Brand: Foxconn

Model: AT-7300

Category: PC/workstation barebones

Type: User manual

This manual is also suitable for

AT-7500

Download PDF

report

Foxconn AT-7300 User manual

This manual is also suitable for

Foxconn AT-7300 User manual

Related papers

Other documents