ProSoft Technology ILX56-PBS User manual

ILX56-PBS
Brand
ProSoft Technology
Model
ILX56-PBS
Type
User manual
ILX56-PBS
PROFIBUS DPV1 Slave
ControlLogix
®
Platform
May 19, 2020
User Manual
ILX56-PBS Preface
ControlLogix® Platform User Manual
Page 2 of 87
Your Feedback Please
We always want you to feel that you made the right decision to use our products. If you have suggestions,
comments, compliments or complaints about our products, documentation, or support, please write or call us.
ProSoft Technology, Inc.
+1 (661) 716-5100
+1 (661) 716-5101 (Fax)
www.prosoft-technology.com
[email protected]
ILX56-PBS User Manual
May 19, 2020
ProSoft Technology
®
, is a registered copyright of ProSoft Technology, Inc. All other brand or product names are
or may be trademarks of, and are used to identify products and services of, their respective owners.
In an effort to conserve paper, ProSoft Technology no longer includes printed manuals with our product
shipments. User Manuals, Datasheets, Sample Ladder Files, and Configuration Files are provided at our website:
www.prosoft-technology.com
Content Disclaimer
This documentation is not intended as a substitute for and is not to be used for determining suitability or reliability
of these products for specific user applications. It is the duty of any such user or integrator to perform the
appropriate and complete risk analysis, evaluation and testing of the products with respect to the relevant specific
application or use thereof. Neither ProSoft Technology nor any of its affiliates or subsidiaries shall be responsible
or liable for misuse of the information contained herein. Information in this document including illustrations,
specifications and dimensions may contain technical inaccuracies or typographical errors. ProSoft Technology
makes no warranty or representation as to its accuracy and assumes no liability for and reserves the right to
correct such inaccuracies or errors at any time without notice. If you have any suggestions for improvements or
amendments or have found errors in this publication, please notify us.
No part of this document may be reproduced in any form or by any means, electronic or mechanical, including
photocopying, without express written permission of ProSoft Technology. All pertinent state, regional, and local
safety regulations must be observed when installing and using this product. For reasons of safety and to help
ensure compliance with documented system data, only the manufacturer should perform repairs to components.
When devices are used for applications with technical safety requirements, the relevant instructions must be
followed. Failure to use ProSoft Technology software or approved software with our hardware products may
result in injury, harm, or improper operating results. Failure to observe this information can result in injury or
equipment damage.
© 2020 ProSoft Technology. All Rights Reserved.
Printed documentation is available for purchase. Contact ProSoft Technology for pricing and availability.
For professional users in the European Union
If you wish to discard electrical and electronic equipment (EEE), please contact your dealer or
supplier for further information.
Warning – Cancer and Reproductive Harm – www.P65Warnings.ca.gov
Agency Approvals and Certifications
Please visit our website: www.prosoft-technology.com
ILX56-PBS Preface
ControlLogix® Platform User Manual
Page 3 of 87
China ROHS
部件名称
Component Name
有害物质
Hazardous substances
鉛
Lead
(Pb)
鎘
Cadmium
(Cd)
六价铬
Hexavalent
Chromium
(Cr(VI))
多溴联苯
Polybrominated
Biphenyls
(PBB)
多溴二苯醚
Polybrominated
Diphenyl
Ethers
(PBDE)
印刷电路板组件
Printed Circuit
Board Assemblies
X
O
O
O
O
接 线和电缆
Wiring and Cable
O
O
O
O
O
塑料部件
Plastic
Components
O
O
O
O
O
本 表 格 依 据 SJ/T 11364 的 规定编制。This table is made per guidance of SJ/T 11364
O: 表示该 有 害 物 质 在 该 部 件 所 有 均 质 材 料 中 的 含 量 均 在 GB/T 26572 规 定 的 限 量 要 求 以 下 。
O: Indicates that this hazardous substance contained in all of the homogeneous
materials for the part is below the limit requirement in GB/T 26572.
X: 表示该 有 害 物 质 至 少 在 该 部 件 的 某 一 均 质 材 料 中 的 含 量 超 出 GB/T 26572 规定的限量要求。
X: Indicates that this hazardous substance contained in at least one of the homogeneous
materials used for this part is above the limit requirement in GB/T 26572.
( 企 业 可 在 此 处 ， 根 据 实 际 情 况 对 上 表 中 打 “X” 的技术原因进行进一步说明。)
(According to actual situation, extra explanations can be given here for the technical reasons of items with "X".)
ILX56-PBS Preface
ControlLogix® Platform User Manual
Page 4 of 87
Contents
Your Feedback Please ......................................................................................................................... 2
Content Disclaimer .............................................................................................................................. 2
1. Preface............................................................................................................................................ 7
Introduction to the ILX56-PBS ................................................................................................. 7
Features .................................................................................................................................. 8
Additional Information ............................................................................................................ 8
2. Installation ...................................................................................................................................... 9
Module Layout ........................................................................................................................ 9
PROFIBUS DP Port (RS485) .................................................................................................... 10
3. Setup ............................................................................................................................................ 11
Install Configuration Software .............................................................................................. 11
Creating a New Project ......................................................................................................... 12
ILX56-PBS Parameters ........................................................................................................... 14
General .......................................................................................................................... 14
PROFIBUS – Slave Mode ................................................................................................ 15
Logix .............................................................................................................................. 16
Adding PROFIBUS DP Devices ............................................................................................... 17
General .......................................................................................................................... 18
PROFIBUS Configuration ............................................................................................... 19
DPV1 .............................................................................................................................. 20
User Parameters ........................................................................................................... 21
Slot Configuration ......................................................................................................... 21
Start-up Parameters ...................................................................................................... 22
DPV1 Objects ................................................................................................................. 23
DPV1 Alarms .................................................................................................................. 24
Module Download ................................................................................................................ 25
Studio 5000 Configuration .................................................................................................... 26
Installing the Add-On Profile (AOP) .............................................................................. 26
Adding a Module to I/O Configuration ......................................................................... 26
PLX50 Configuration Utility Project File ........................................................................ 28
Generating a Logix .L5X File .................................................................................................. 29
Local Rack Module Location .......................................................................................... 29
Remote Rack Module Location ..................................................................................... 30
Generating the L5X File ................................................................................................. 31
ILX56-PBS Preface
ControlLogix® Platform User Manual
Page 5 of 87
SD Card .................................................................................................................................. 35
Firmware ............................................................................................................................... 35
Configuration .................................................................................................................... 36
Manual Copy ................................................................................................................. 36
PLX50 Configuration Utility Upload .............................................................................. 38
4. Operation ..................................................................................................................................... 39
Logix Operation ..................................................................................................................... 39
PROFIBUS DP - Slave ..................................................................................................... 39
General Status ........................................................................................................................... 39
General Control ......................................................................................................................... 42
Status and DPV0 Data Exchange ............................................................................................... 43
DPV1 Class 1 Messaging (MS1) ................................................................................................. 45
Alarming .................................................................................................................................... 46
Upgrading Firmware ............................................................................................................. 48
5. Diagnostics ................................................................................................................................... 50
LEDs ....................................................................................................................................... 50
Module Status Monitoring .................................................................................................... 52
ILX56-PBS Status ........................................................................................................... 53
General ...................................................................................................................................... 53
Slave Status ............................................................................................................................... 55
Logix Statistics ........................................................................................................................... 56
ILX56-PBS Emulated Slave Device Status ...................................................................... 57
PROFIBUS Packet Capture ..................................................................................................... 58
Packet Details ................................................................................................................ 60
Packet Filter .................................................................................................................. 61
Saving Packet Filter Options ......................................................................................... 62
Module Event Log ................................................................................................................. 63
6. Technical Specifications ............................................................................................................... 64
Electrical ................................................................................................................................ 64
PROFIBUS DP ......................................................................................................................... 64
Certifications ......................................................................................................................... 64
7. PROFIBUS DP ................................................................................................................................ 65
Introduction .......................................................................................................................... 65
PROFIBUS master and slave .................................................................................................. 66
PROFIBUS master class 1 (DPM1) or class 2 (DPM2) ............................................................ 66
Cyclic communication ........................................................................................................... 67
ILX56-PBS Preface
ControlLogix® Platform User Manual
Page 6 of 87
Acyclic communication ......................................................................................................... 67
Topology of PROFIBUS DP ..................................................................................................... 67
PROFIBUS DP cable description ............................................................................................ 68
PROFIBUS DP connector description .................................................................................... 68
8. ILX56-PBS Quickstart .................................................................................................................... 69
GSD File Management Tool Installation ............................................................................... 69
Creating a New Project ......................................................................................................... 70
PROFIBUS Configuration ............................................................................................... 71
Logix Configuration ....................................................................................................... 71
Adding a PROFIBUS Slave ...................................................................................................... 72
Downloading the Configuration to the ILX56-PBS ................................................................ 74
ControlLogix Configuration ................................................................................................... 75
PROFIBUS Master Configuration ........................................................................................... 77
9. Support, Service & Warranty ....................................................................................................... 86
Contacting Technical Support ............................................................................................... 86
Warranty Information ........................................................................................................... 86
10. Index .......................................................................................................................................... 87
ILX56-PBS Preface
ControlLogix® Platform User Manual
Page 7 of 87
1. Preface
Introduction to the ILX56-PBS
This manual describes the installation, operation, and diagnostics of the ProSoft ILX56-PBS
PROFIBUS DPV0/DPV1 Slave module.
The ILX56-PBS slots into a 1756 ControlLogix backplane and allows the user to interface
PROFIBUS DP to a ControlLogix controller via the ControlLogix backplane.
The ILX56-PBS can operate as one or more PROFIBUS DPV0/DPV1 Slaves. This will allow
a ControlLogix controller to exchange process, alarming, and diagnostic data with a
PROFIBUS DP Master.
Figure 1.1 – Typical ILX56-PBS PROFIBUS Slave architecture
ILX56-PBS Preface
ControlLogix® Platform User Manual
Page 8 of 87
Features
The ILX56-PBS will allow the user to interface PROFIBUS DPV0/DPV1 to a ControlLogix
controller via the 1756 ControlLogix backplane. The ILX56-PBS also supports an onboard
non-volatile event log for improved fault finding.
PROFIBUS Slave (ILX56-PBS)
The ILX56-PBS can also be configured to emulate up to 10 PROFIBUS slave devices. Each
slave device emulated by the ILX56-PBS can be configured to provide DPV0 data exchange
with a PROFIBUS Master on the network.
The data will be formatted into the engineering units for use in a ControlLogix platform by
using the automatically-generated mapping imports for Logix User Defined Data Types
(UDTs).
Each emulated slave can also be configured to exchange DPV1 Class 1 data by mapping
Logix tags for the relevant DPV1 data exchange. Each emulated slave will also be able to
provide DPV1 alarming for the PROFIBUS Master.
Additional Information
The following documents contain additional information that can assist the user with the
module installation and operation.
Resource
Link
PLX50 Configuration Utility
Installation
www.prosoft-technology.com
ILX56-PBS User Manual
ILX56-PBS Datasheet
www.prosoft-technology.com
Table 1.1 - Additional Information
ILX56-PBS Installation
ControlLogix® Platform User Manual
Page 9 of 87
2. Installation
Module Layout
The ILX56-PBS has one RS485 PROFIBUS DP port at the front of the module.
NOTE: All required power for the module is derived from the ControlLogix
backplane.
The module provides 3 diagnostic LEDs and a 4-character alpha-numeric LED display that
provides the mode and status of the module.
Figure 2.1 – ILX56-PBS Front View
Figure 2.2 – ILX56-PBS Bottom View
ILX56-PBS Installation
ControlLogix® Platform User Manual
Page 10 of 87
The module provides two DIP switches and a slot for a SD memory card located on the bottom
of the module. These switches can only be accessed when the module is removed from the
ControlLogix chassis.
DIP Switch
Description
DIP Switch 1
Used to force the module into “Safe Mode”. When in “Safe Mode” the module
will not load the application firmware and will wait for new firmware to be
downloaded. This should only be used in the rare occasion when a firmware
update was interrupted at a critical stage.
DIP Switch 2
Used to prevent changes to the configuration.
Table 2.1. - DIP Switch Settings
PROFIBUS DP Port (RS485)
The PROFIBUS DP port uses a female DB9 connector. This provides connection for the
communication conductors, cable shielding and +5Vdc output power.
Figure 2.3 – ILX56-PBS PROFIBUS DP (RS485) DB9 connector
Pin
Signal
Description
1
-
Not connected
2
-
Not connected
3
RxD/TxD-P
Data received and transmit (+)
4
CNTR-P
Control signal to repeater (+)
5
DGND
Reference potential for +5Vdc
6
VP
+5Vdc for terminating resistors (active termination)
7
-
Not connected
8
RxD/TxD-N
Data received and transmit (-)
9
-
Not connected
Table 2.2 – DB9 Connector layout
ILX56-PBS Setup
ControlLogix® Platform User Manual
Page 11 of 87
3. Setup
Install Configuration Software
All the network setup and configuration of the module is achieved by means of the ProSoft
PLX50 Configuration Utility. This software can be downloaded from:
http://www.prosoft-technology.com.
Figure 3.1. - ProSoft PLX50 Configuration Utility Environment
ILX56-PBS Setup
ControlLogix® Platform User Manual
Page 12 of 87
Creating a New Project
Before the user can configure the module, a new PLX50 Configuration Utility project must be
created.
1 Under the File menu, select New.
Figure 3.2 - Creating a new project
2 A new device can now be added by selecting Add under the Device menu.
Figure 3.3 - Adding a new device
ILX56-PBS Setup
ControlLogix® Platform User Manual
Page 13 of 87
3 In the Add New Device window select the ILX56-PBS and click the Ok button.
Figure 3.4 – ILX56-PBS
4 The device will appear in the Project Explorer tree as shown below, and its
configuration window opened. The device configuration window can be reopened by
either double-clicking the module in the Project Explorer tree or right-clicking the
module and selecting Configuration.
Figure 3.5 – ILX56-PBS configuration
ILX56-PBS Setup
ControlLogix® Platform User Manual
Page 14 of 87
ILX56-PBS Parameters
The ILX56-PBS parameters are configured by the PLX50 Configuration Utility.
NOTE: Refer to the additional information section for documentation and
installation links for ProSoft’s PLX50 Configuration Utility.
General
The General configuration is shown in the following figure. The ILX56-PBS General
configuration window is opened by either double-clicking on the module in the tree, or right-
clicking the module and selecting Configuration.
Figure 3.6 – ILX56-PBS General configuration
The General configuration consists of the following parameters:
Parameter
Description
Instance Name
This parameter is a user-defined name to identify between various ILX56-PBS
modules.
Description
This parameter is used to provide a more detailed description of the ILX56-PBS.
Mode
The ILX56-PBS can operate in one of two modes:
Quiet
This mode allows the user to connect the ILX56-PBS to an active bus and run a
DP packet capture. In this mode the ILX56-PBS will not communicate on the DP
Bus, but rather only listen.
Slave
The ILX56-PBS will emulate multiple PROFIBUS Slave devices.
Table 3.1 - General configuration parameters
ILX56-PBS Setup
ControlLogix® Platform User Manual
Page 15 of 87
PROFIBUS – Slave Mode
The ILX56-PBS PROFIBUS configuration is shown in the following figure. The ILX56-PBS
PROFIBUS configuration window is opened by either double-clicking on the module in the
tree, or right-clicking the module and selecting Configuration.
Figure 3.7 – ILX56-PBS PROFIBUS configuration – Slave Mode
The PROFIBUS slave configuration consists of the following parameters:
Parameter
Description
BAUD Rate
Baud Rate (in Kbps) of the PROFIBUS network: 9.6, 19.2, 45.45,
93.75, 187.5, 500, 1500, 3000, 6000 or 12000 Kbps. The baud rate selected
should be supported by the PROFIBUS master. The baud rate should be
selected depending on the cable length, see chapter “PROFIBUS DP”
Table 3.2 - PROFIBUS configuration parameters – Slave Mode
ILX56-PBS Setup
ControlLogix® Platform User Manual
Page 16 of 87
Logix
The Logix configuration is shown in the following figure. The ILX56-PBS Logix configuration
window is opened by either double-clicking on the module in the tree, or right-clicking the
module and selecting Configuration.
Figure 3.8 – ILX56-PBS Logix configuration
The Logix configuration consists of the following parameters:
Parameter
Description
Logix Connections
The number of Logix (CIP) Connections (1 to 10) to be used in the exchange
with Logix.
Each backplane connection is configured with 500 bytes output and 496 byte
input and 0 byte configuration.
NOTE: This value must match the same number of connections configured
in the Logix IO tree.
Controller Path
This is the CIP path to the Logix controller.
This path will be used for the Class 3 data exchanges for DPV1 objects and
alarms.
Response Timeout
The maximum time (ms) allowed for a Class 3 response from the Logix
controller.
Logix Base Tag A/B
This is the tagname of the ILX56-PBS used for the input and output assembly.
For example, if the module is in the local slot connected to a Logix controller
the base Logix tag will be local:x (where x is the slot number).
The base tagname is used when generating the Logix L5X file, which will
automatically map the required data.
NOTE: Only Logix Base Tag A will be relevant.
Table 3.3 - Logix configuration parameters
ILX56-PBS Setup
ControlLogix® Platform User Manual
Page 17 of 87
Adding PROFIBUS DP Devices
The user will need to add each PROFIBUS device to the ILX56-PBS. Each PROFIBUS device
can then be configured. This is done by right-clicking on the PROFIBUS Devices item in the
tree and selecting Add PROFIBUS Device.
Figure 3.9 – Adding a PROFIBUS Field Device
When adding a PROFIBUS Device in Slave Mode, a static GSD file, based on the ILX56
module, will be automatically applied.
Module
GSD Filename
ILX56-PBS
PSFT0EE3.GSD
Table 3.4 – Slave GSD File
ILX56-PBS Setup
ControlLogix® Platform User Manual
Page 18 of 87
General
The General configuration is shown in the following figure. The Device General Configuration
window is opened by either double-clicking on the slave device in the tree, or right-clicking the
slave device and selecting Configuration.
Figure 3.10 – Device General configuration parameters
The General configuration consists of the following parameters:
Parameter
Description
Instance Name
The device instance name which will be used to create the Tag
names and UDTs in Logix.
Table 3.5 –Device General configuration parameters
ILX56-PBS Setup
ControlLogix® Platform User Manual
Page 19 of 87
PROFIBUS Configuration
The PROFIBUS configuration is shown in the following figure. The Device PROFIBUS
configuration window is opened by either double-clicking on the slave device in the tree, or
right-clicking the slave device and selecting Configuration.
Figure 3.11 – Device PROFIBUS configuration parameters
The PROFIBUS configuration consists of the following parameters:
Parameter
Description
Node Address
This is the ILX56-PBS node address on the PROFIBUS network.
TSDR
N/A
Minimum Slave Interval
N/A
Watchdog Enable
N/A
Watchdog Value
N/A
Group Membership
N/A
Table 3.6 – Field Device PROFIBUS configuration parameters
ILX56-PBS Setup
ControlLogix® Platform User Manual
Page 20 of 87
DPV1
The DPV1 configuration is shown in the following figure. The slave device DPV1 configuration
window is opened by either double-clicking on the slave device in the tree, or right-clicking the
slave device and selecting Configuration.
Figure 3.12 – Device DPV1 configuration parameters
The DPV1 configuration consists of the following parameters:
Parameter
Description
Enable DPV1
Indicates if the slave supports DPV1 Class 1 access (read and
write) or alarms. The default value is based on the information
provided by the GSD File.
Base 1ms
N/A
Enable Fail Safe
N/A
Check Config
N/A
Alarm Mode
N/A
Alarm Ack uses SAP50
This will force the ILX56-PBS to use Service Access Point (SAP)
50 to acknowledge alarms.
Alarm Enables
N/A
Table 3.7 – Device DPV1 configuration parameters
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87

ProSoft Technology ILX56-PBS User manual

ILX56-PBS
Brand
ProSoft Technology
Model
ILX56-PBS
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents