Artel InfinityLink ILC274 Quick start guide

Type
Quick start guide

This manual is also suitable for

Artel InfinityLink ILC274D is a high-quality SD-SDI, ASI Digital Video 4 Ch TDM De-Multiplexer. It is used for de-multiplexing four channels of 270 Mb/s video data from a single optical input. The ILC274D is ideal for use in a variety of applications, including broadcast, production, and post-production.

The ILC274D has a number of features that make it a versatile and powerful tool. These features include:

  • Four channels of 270 Mb/s video de-multiplexing
  • Optical input and four electrical outputs
  • DIP switch configuration for easy setup
  • Front panel LEDs for status indication
  • EMS override for remote configuration

Artel InfinityLink ILC274D is a high-quality SD-SDI, ASI Digital Video 4 Ch TDM De-Multiplexer. It is used for de-multiplexing four channels of 270 Mb/s video data from a single optical input. The ILC274D is ideal for use in a variety of applications, including broadcast, production, and post-production.

The ILC274D has a number of features that make it a versatile and powerful tool. These features include:

  • Four channels of 270 Mb/s video de-multiplexing
  • Optical input and four electrical outputs
  • DIP switch configuration for easy setup
  • Front panel LEDs for status indication
  • EMS override for remote configuration
23
Artel ships the ILC274D configured as follows:
All four channels enabled
No video detected alarm disabled
EMS override enabled (IL Manager can change the ILC274D configuration)
Configuration Switch Functions
SW1 Controls the channel (A, B, C and D)
output operation, enabling/disabling
of the optical TX (repeater)
operation, controls the loss of video
alarm option, and enables the EMS
over ride function.
SW1
SW1 Configuration
SW1 Function Off On
S1 Ch A Operation Disabled Normal Operation
S2 Ch B Operation Disabled Normal Operation
S3 Ch C Operation Disabled Normal Operation
S4 Ch D Operation Disabled Normal Operation
S5 Optical TX Disable Repeater Operation Disables transmitter/ repeater
S6 Video Alarm Disable Alarm on video loss No alarm on video loss
S7 Reserved - Must be On
S8 EMS Override Local Control RemoteControl
Factory Default: All On
DIP SWITCH CONFIGURATIONS
InfinityLink ILC274D - SD-SDI, ASI Digital
Video 4 Ch TDM De-Multiplexer
QUICK START GUIDES
24
LED Function Color Description
OK
ILC274D
Module
Status
OFF If power is applied to the system, an internal fault with the ILC274D may exist
n Green
Normal operation
n Yellow
If no other status LEDs indicate a minor alarm, then a temperature alarm is indicated
n Red
If no other status LEDs indicate a major alarm, then an internal error is indicated, such as an
onboard communications error or an onboard power error
EMS
IL Manager
System
Status
OFF
The ILC274D module is in local mode and its configuration is controlled by the onboard
configuration switches
n Green
The ILC274D module is in remote mode and the configuration has been set by the EMS. When in
remote mode, the actual configuration of the module will likely not match the settings of the
configuration switches and changing the configuration switches will have no eect on the
module operation
TX
Transmitter
Status
OFF Transmitter is disabled
n Green
Normal operation (repeating input signal)
n Red
SFP TX failure exists
Red
No SFP is installed
RX
Receiver
Status
n Green
Normal operation
n Yellow
Link errors detected
Yellow
Receive optical power is high
n Red
No input signal or the input signal type is incorrect (not a valid ILC274M or
ILC274M signal)
Red
Possible causes:
• A low receiver power condition exists
• No SFP is installed
• An SFP RX failure exists
A, B, C, D
270 Mb/s
Channel
Status
OFF Channel is disabled on the ILC274D or ILC274M
n Green
270 Mb/s video detected
n Yellow
No signal to the ILC274M
n Red
Video input signal rate is outside the range (270 Mb +/- 100 ppm)
Flashing yellow | Flashing red
Install SFP
DLC274D FRONT PANEL LEDS
AR208-006030-B00_A
T: 978-263-5775
www.artel.com
Sales
InfinityLink ILC274D - SD-SDI, ASI Digital Video 4 Ch TDM De-Multiplexer
  • Page 1 1
  • Page 2 2

Artel InfinityLink ILC274 Quick start guide

Type
Quick start guide
This manual is also suitable for

Artel InfinityLink ILC274D is a high-quality SD-SDI, ASI Digital Video 4 Ch TDM De-Multiplexer. It is used for de-multiplexing four channels of 270 Mb/s video data from a single optical input. The ILC274D is ideal for use in a variety of applications, including broadcast, production, and post-production.

The ILC274D has a number of features that make it a versatile and powerful tool. These features include:

  • Four channels of 270 Mb/s video de-multiplexing
  • Optical input and four electrical outputs
  • DIP switch configuration for easy setup
  • Front panel LEDs for status indication
  • EMS override for remote configuration

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI