NXP MAC7101 Reference guide

MAC7100RM

Rev. 2

02/2009

MAC7100 Microcontroller Family

Reference Manual

Devices Supported:

MAC7101 MAC7106

MAC7111 MAC7112

MAC7116 MAC7121

MAC7122 MAC7126

MAC7131 MAC7136

MAC7141 MAC7142

How to Reach Us:

Home Page:

www.freescale.com

Web Support:

http://www.freescale.com/support

USA/Europe or Locations Not Listed:

Freescale Semiconductor, Inc.

Technical Information Center, EL516

2100 East Elliot Road

Tempe, Arizona 85284

1-800-521-6274 or +1-480-768-2130

www.freescale.com/support

Europe, Middle East, and Africa:

Freescale Halbleiter Deutschland GmbH

Technical Information Center

Schatzbogen 7

81829 Muenchen, Germany

+44 1296 380 456 (English)

+46 8 52200080 (English)

+49 89 92103 559 (German)

+33 1 69 35 48 48 (French)

www.freescale.com/support

Japan:

Freescale Semiconductor Japan Ltd.

Headquarters

ARCO Tower 15F

1-8-1, Shimo-Meguro, Meguro-ku,

Tokyo 153-0064

Japan

0120 191014 or +81 3 5437 9125

[email protected]

Asia/Pacific:

Freescale Semiconductor China Ltd.

Exchange Building 23F

No. 118 Jianguo Road

Chaoyang District

Beijing 100022

China

+86 10 5879 8000

[email protected]

For Literature Requests Only:

Freescale Semiconductor Literature Distribution Center

P.O. Box 5405

Denver, Colorado 80217

1-800-441-2447 or +1-303-675-2140

Fax: +1-303-675-2150

LDCForFreescaleSemiconductor@hibbertgroup.com

Information in this document is provided solely to enable system and

software implementers to use Freescale Semiconductor products. There are

no express or implied copyright licenses granted hereunder to design or

fabricate any integrated circuits or integrated circuits based on the

information in this document.

Freescale Semiconductor reserves the right to make changes without further

notice to any products herein. Freescale Semiconductor makes no warranty,

representation or guarantee regarding the suitability of its products for any

particular purpose, nor does Freescale Semiconductor assume any liability

arising out of the application or use of any product or circuit, and specifically

disclaims any and all liability, including without limitation consequential or

incidental damages. “Typical” parameters that may be provided in Freescale

Semiconductor data sheets and/or specifications can and do vary in different

applications and actual performance may vary over time. All operating

parameters, including “Typicals”, must be validated for each customer

application by customer’s technical experts. Freescale Semiconductor does

not convey any license under its patent rights nor the rights of others.

Freescale Semiconductor products are not designed, intended, or authorized

for use as components in systems intended for surgical implant into the body,

or other applications intended to support or sustain life, or for any other

application in which the failure of the Freescale Semiconductor product could

create a situation where personal injury or death may occur. Should Buyer

purchase or use Freescale Semiconductor products for any such unintended

or unauthorized application, Buyer shall indemnify and hold Freescale

Semiconductor and its officers, employees, subsidiaries, affiliates, and

distributors harmless against all claims, costs, damages, and expenses, and

reasonable attorney fees arising out of, directly or indirectly, any claim of

personal injury or death associated with such unintended or unauthorized

use, even if such claim alleges that Freescale Semiconductor was negligent

regarding the design or manufacture of the part.

Freescale™ and the Freescale logo are trademarks of Freescale

Semiconductor, Inc. All other product or service names are the property

of their respective owners. The ARM POWERED logo is a registered

trademark of ARM Limited. ARM7TDMI-S is a trademark of ARM Limited.

Java and all other Java-based marks are trademarks or registered

trademarks of Sun Microsystems, Inc. in the U.S. and other countries.

The Bluetooth trademarks are owned by their proprietor and used by

Freescale Semiconductor, Inc. under license.

MAC7100RM

Rev. 2

02/2009

MAC7100 Microcontroller Family Reference Manual, Rev. 2

Freescale Semiconductor iii

1Introduction

2Signal Description

3Voltage Regulator Module (VREG)

4System Clocks Module (OSC and CRG)

5Resets

6Exceptions

7Modes of Operation

8Device Memory Map

9ARM7TDMI-S™ Processor Core

10Interrupt Controller Module (INTC)

11Miscellaneous Control Module (MCM)

12Enhanced Direct Memory Access Controller Module (eDMA)

13External Interface Module (EIM)

14Cross-Bar Switch Module (XBS)

15Common Flash Module (CFM)

16AMBA to IP Bus Bridge Module (AIPS)

17DMA Channel Multiplexer Module (DMAMux)

18Port Integration Module (PIM)

19Analog-to-Digital Converter Module (ATD)

20Enhanced Modular I/O Subsystem Module (eMIOS)

21Enhanced Serial Communications Interface Module (eSCI)

22Deserial Serial Peripheral Interface Module (DSPI)

23Controller Area Network Module (FlexCAN)

24Inter-Integrated Circuit Bus Module (I

2

C)

25Periodic Interrupt Timer Module (PIT)

26System Services Module (SSM)

ADebug Interface

BA7S Nexus 2 Module

CRegister Memory Map Quick Reference

DMask Set Differences Summary

Tab Pages

MAC7100 Microcontroller Family Reference Manual, Rev. 2

iv Freescale Semiconductor

1 Introduction

2 Signal Description

3 Voltage Regulator Module (VREG)

4 System Clocks Module (OSC and CRG)

5 Resets

6 Exceptions

7 Modes of Operation

8 Device Memory Map

9 ARM7TDMI-S™ Processor Core

10 Interrupt Controller Module (INTC)

11 Miscellaneous Control Module (MCM)

12 Enhanced Direct Memory Access Controller Module (eDMA)

13 External Interface Module (EIM)

14 Cross-Bar Switch Module (XBS)

15 Common Flash Module (CFM)

16 AMBA to IP Bus Bridge Module (AIPS)

17 DMA Channel Multiplexer Module (DMAMux)

18 Port Integration Module (PIM)

19 Analog-to-Digital Converter Module (ATD)

20 Enhanced Modular I/O Subsystem Module (eMIOS)

21 Enhanced Serial Communications Interface Module (eSCI)

22 Deserial Serial Peripheral Interface Module (DSPI)

23 Controller Area Network Module (FlexCAN)

24 Inter-Integrated Circuit Bus Module (I

2

C)

25 Periodic Interrupt Timer Module (PIT)

26 System Services Module (SSM)

A Debug Interface

B A7S Nexus 2 Module

C Register Memory Map Quick Reference

D Mask Set Differences Summary

MAC7100 Microcontroller Family Reference Manual, Rev. 2

Freescale Semiconductor v

Contents

Paragraph

Number

Title

Page

Number

Tables............................................................................................................................. xxix

Figures ......................................................................................................................... xxxix

Preface

Document Structure ............................................................................................................ li

How To Use This Document............................................................................................... li

Conventions ....................................................................................................................... lii

Terminology......................................................................................................................liii

Register Descriptions....................................................................................................... lvii

Revision History

Content Changes by Document Version........................................................................... lix

Chapter 1

Introduction

1.1 Overview.......................................................................................................................... 1-1

1.2 Block Diagram................................................................................................................. 1-2

1.3 Features............................................................................................................................ 1-4

1.4 Modes of Operation ......................................................................................................... 1-9

Chapter 2

Signal Description

2.1 External Signal Description........................................................................................... 2-11

2.1.1 Clocks and Control .................................................................................................... 2-11

2.1.1.1 EXTAL, XTAL — Oscillator ................................................................................ 2-11

2.1.1.2 XFC — PLL Loop Filter ....................................................................................... 2-11

2.1.1.3 RESET — External Reset...................................................................................... 2-11

2.1.1.4 TCK — Test Clock................................................................................................ 2-11

2.1.1.5 TMS — Test Mode................................................................................................ 2-11

2.1.1.6 TDI — Test Data In............................................................................................... 2-11

2.1.1.7 TDO — Test Data Out........................................................................................... 2-12

2.1.1.8 TA / AS — Transfer Acknowledge / Address Strobe............................................ 2-12

2.1.1.9 TEST — Factory Test............................................................................................ 2-12

Contents

Paragraph

Number

Title

Page

Number

MAC7100 Microcontroller Family Reference Manual, Rev. 2

vi Freescale Semiconductor

2.1.1.10 Configuration and Optional Control Signals......................................................... 2-12

2.1.2 General Purpose / Peripheral I/O............................................................................... 2-12

2.1.2.1 Port A Signal Group .............................................................................................. 2-13

2.1.2.2 Port B Signal Group............................................................................................... 2-15

2.1.2.3 Port C Signal Group............................................................................................... 2-16

2.1.2.4 Port D Signal Group .............................................................................................. 2-16

2.1.2.5 Port E Signal Group............................................................................................... 2-17

2.1.2.6 Port F Signal Group............................................................................................... 2-18

2.1.2.7 Port G Signal Group .............................................................................................. 2-18

2.1.2.8 Port H Signal Group .............................................................................................. 2-20

2.1.2.9 Port I Signal Group................................................................................................ 2-20

2.2 Power Supply, Bypass and Reference............................................................................ 2-20

2.2.1 V

DD

X,V

SS

X — I/O Drivers Power and Ground....................................................... 2-20

2.2.2 V

DD

R, V

SS

R — Internal Voltage Regulator Supply ................................................. 2-20

2.2.3 V

DD

A, V

SS

A — Analog Reference Supply .............................................................. 2-21

2.2.4 V

DD

2.5, V

SS

2.5 — Core Power Supply Bypass........................................................ 2-21

2.2.5 V

DD

PLL, V

SS

PLL — PLL Power Supply Bypass.................................................... 2-21

2.2.6 V

RH

, V

RL

— ATD Reference Voltage....................................................................... 2-21

2.3 Signal Properties Summary ........................................................................................... 2-22

2.4 Packaging Options......................................................................................................... 2-27

Chapter 3

Voltage Regulator Module (VREG)

3.1 Overview........................................................................................................................ 3-29

3.2 Features.......................................................................................................................... 3-29

3.3 Modes of Operation ....................................................................................................... 3-31

3.4 Signal Description.......................................................................................................... 3-31

3.4.1 V

DD

R, V

SS

R — Regulator Power Input.................................................................... 3-32

3.4.2 V

DD

A, V

SS

A — Regulator Reference Input ............................................................. 3-32

3.4.3 V

DD

2.5, V

SS

2.5 — Regulator Output 1 (Core Logic)............................................... 3-32

3.4.4 V

DD

PLL, V

SS

PLL — Regulator Output 2 (PLL)...................................................... 3-32

3.5 Memory Map / Register Definition ............................................................................... 3-32

3.5.1 Register Descriptions................................................................................................. 3-33

3.5.1.1 VREG High Temperature Control Register (VREGHTCL).................................. 3-33

3.5.1.2 VREG Control Register (VREGCTRL)................................................................ 3-33

3.5.1.3 VREG Autonomous Periodic Interrupt Control Register (VREGAPICL)............ 3-34

3.5.1.4 VREG Autonomous Periodic Interrupt Trimming Register (VREGAPITR)........ 3-35

3.6 Functional Description................................................................................................... 3-36

3.6.1 REG – Regulator Core............................................................................................... 3-36

Contents

Paragraph

Number

Title

Page

Number

MAC7100 Microcontroller Family Reference Manual, Rev. 2

Freescale Semiconductor vii

3.6.1.1 Full Performance Mode.........................................................................................3-36

3.6.1.2 Reduced Power Mode............................................................................................ 3-37

3.6.2 LVD – Low Voltage Detect........................................................................................ 3-37

3.6.3 POR – Power-On Reset ............................................................................................. 3-37

3.6.4 LVR – Low Voltage Reset ......................................................................................... 3-37

3.6.5 CTRL – Regulator Control........................................................................................ 3-37

3.6.6 API – Autonomous Periodic Interrupt....................................................................... 3-37

3.6.7 Resets......................................................................................................................... 3-38

3.6.7.1 Power-On Reset (POR).......................................................................................... 3-38

3.6.7.2 Low-Voltage Reset (LVR) ..................................................................................... 3-38

3.6.8 Interrupts.................................................................................................................... 3-38

3.6.8.1 LVI – Low Voltage Interrupt.................................................................................. 3-38

3.6.8.2 API – Autonomous Periodic Interrupt................................................................... 3-39

3.7 Initialization / Application Information......................................................................... 3-39

3.7.1 Circuit Board Layout................................................................................................. 3-39

Chapter 4

System Clocks Module (OSC and CRG)

4.1 Overview........................................................................................................................ 4-45

4.2 On-Chip Oscillator (OSC) Module................................................................................ 4-47

4.2.1 OSC Overview........................................................................................................... 4-47

4.2.2 OSC Features............................................................................................................. 4-47

4.2.3 OSC Modes of Operation .......................................................................................... 4-48

4.2.4 OSC Signal Description............................................................................................. 4-48

4.2.4.1 V

DD

PLL, V

SS

PLL................................................................................................. 4-48

4.2.4.2 EXTAL, XTAL...................................................................................................... 4-48

4.2.4.3 CLKOUT / XCLKS

............................................................................................... 4-49

4.2.5 OSC Functional Description...................................................................................... 4-50

4.2.5.1 Gain control........................................................................................................... 4-50

4.2.5.2 Clock Monitor........................................................................................................ 4-50

4.3 Clock and Reset Generator (CRG) Module................................................................... 4-50

4.3.1 CRG Overview .......................................................................................................... 4-50

4.3.2 CRG Features............................................................................................................. 4-51

4.3.3 CRG Modes of Operation.......................................................................................... 4-52

4.3.4 CRG Signal Description ............................................................................................ 4-52

4.3.4.1 XFC........................................................................................................................ 4-52

4.3.4.2 RESET

................................................................................................................... 4-53

4.3.4.3 CLKOUT / XCLKS............................................................................................... 4-53

4.3.5 CRG Memory Map / Register Definition.................................................................. 4-53

Contents

Paragraph

Number

Title

Page

Number

MAC7100 Microcontroller Family Reference Manual, Rev. 2

viii Freescale Semiconductor

4.3.5.1 CRG Synthesizer Register (SYNR)....................................................................... 4-54

4.3.5.2 CRG Reference Divider Register (REFDV).......................................................... 4-54

4.3.5.3 CRG Flags Register (CRGFLG)............................................................................ 4-55

4.3.5.4 CRG Interrupt Enable Register (CRGINT)........................................................... 4-56

4.3.5.5 CRG Clock Select Register (CLKSEL)................................................................. 4-57

4.3.5.6 CRG PLL Control Register (PLLCTL)................................................................. 4-58

4.3.5.7 CRG Stop/Doze Control Register (SDMCTL)...................................................... 4-59

4.3.5.8 CRG BDM Control Register (BDMCTL)............................................................. 4-60

4.3.6 CRG Functional Description ..................................................................................... 4-60

4.3.6.1 Phase Locked Loop (PLL)..................................................................................... 4-60

4.3.6.2 System Clocks Generator ......................................................................................4-63

4.3.6.3 Clock Monitor (CM).............................................................................................. 4-64

4.3.6.4 Clock Quality Checker .......................................................................................... 4-64

4.3.6.5 Software Watchdog Timer (SWT)......................................................................... 4-66

4.3.6.6 Real Time Interrupt (RTI)...................................................................................... 4-66

4.3.6.7 Resets..................................................................................................................... 4-66

4.3.6.8 Software Watchdog Timer (SWT) Reset............................................................... 4-69

4.3.6.9 Interrupts................................................................................................................ 4-70

4.3.6.10 CRG Operating Mode Details ...............................................................................4-70

4.4 System Clocks Summary............................................................................................... 4-81

Chapter 5

Resets

5.1 Effects of Reset.............................................................................................................. 5-83

5.1.1 I/O pins ...................................................................................................................... 5-83

5.1.2 Memory...................................................................................................................... 5-83

5.2 Keyboard Wake-up on Port Pins.................................................................................... 5-83

Chapter 6

Exceptions

6.1 Exception Vector Assignments...................................................................................... 6-85

Chapter 7

Modes of Operation

7.1 Chip Hardware Configuration Summary....................................................................... 7-87

7.1.1 MCU Mode Selection................................................................................................ 7-87

Contents

Paragraph

Number

Title

Page

Number

MAC7100 Microcontroller Family Reference Manual, Rev. 2

Freescale Semiconductor ix

7.1.1.1 Expanded Modes ...................................................................................................7-88

7.1.1.2 Single-Chip Modes................................................................................................ 7-88

7.1.1.3 Data Flash Boot Mode........................................................................................... 7-88

7.1.2 Oscillator Type Selection........................................................................................... 7-88

7.1.3 External Bus Interface Configuration........................................................................ 7-88

7.1.4 Nexus Port Configuration.......................................................................................... 7-88

7.2 Security.......................................................................................................................... 7-89

7.2.1 Securing the Microcontroller..................................................................................... 7-89

7.2.2 Operation of the Secured Microcontroller................................................................. 7-89

7.2.2.1 Secured Single-Chip Mode.................................................................................... 7-89

7.2.2.2 Secured Expanded Mode....................................................................................... 7-89

7.2.3 Unsecuring the Microcontroller................................................................................. 7-90

7.2.3.1 Backdoor Access Key............................................................................................ 7-90

7.2.3.2 Lockout Recovery Procedure ................................................................................ 7-90

7.3 Power Consumption Considerations.............................................................................. 7-90

7.3.1 Run Mode .................................................................................................................. 7-91

7.3.2 Doze Mode................................................................................................................. 7-91

7.3.3 Stop Mode.................................................................................................................. 7-91

7.3.4 Pseudo-Stop Mode..................................................................................................... 7-91

7.4 Mode and Configuration Identification ......................................................................... 7-91

Chapter 8

Device Memory Map

8.1 Memory Map Details..................................................................................................... 8-93

8.1.1 Normal Single-Chip Mode......................................................................................... 8-95

8.1.2 Secured Single-Chip Mode........................................................................................ 8-95

8.1.3 Normal Expanded Mode............................................................................................ 8-96

8.1.4 Secured Expanded Mode........................................................................................... 8-97

8.1.5 Normal/Secured Data Flash Boot Mode.................................................................... 8-97

8.1.6 Peripheral Bus Memory Map..................................................................................... 8-99

8.2 Accessing Registers..................................................................................................... 8-100

8.2.1 32-Bit Register Accesses......................................................................................... 8-100

8.2.2 16-Bit Register Accesses......................................................................................... 8-100

8.2.3 8-Bit Register Accesses........................................................................................... 8-100

Chapter 9

ARM7TDMI-S™ Processor Core

9.1 Overview...................................................................................................................... 9-101

Contents

Paragraph

Number

Title

Page

Number

MAC7100 Microcontroller Family Reference Manual, Rev. 2

x Freescale Semiconductor

Chapter 10

Interrupt Controller Module (INTC)

10.1 Overview.................................................................................................................... 10-103

10.2 Features...................................................................................................................... 10-104

10.3 Review of ARM7™ Interrupt Architecture............................................................... 10-104

10.4 Signal Description...................................................................................................... 10-105

10.4.1 XIRQ...................................................................................................................... 10-105

10.4.2 IRQ......................................................................................................................... 10-105

10.5 Memory Map / Register Definition ........................................................................... 10-105

10.5.1 Register Descriptions............................................................................................. 10-108

10.5.1.1 INTC Interrupt Pending Register (IPRH, IPRL)............................................... 10-108

10.5.1.2 INTC Interrupt Mask Register (IMRH, IMRL)................................................. 10-109

10.5.1.3 INTC Force Interrupt Register (INTFRCH, INTFRCL)................................... 10-110

10.5.1.4 INTC Module Configuration Register (ICONFIG)............................................10-111

10.5.1.5 INTC Set Interrupt Mask Register (SIMR)....................................................... 10-112

10.5.1.6 INTC Clear Interrupt Mask Register (CIMR)................................................... 10-112

10.5.1.7 INTC Current Level Mask Register (CLMASK).............................................. 10-113

10.5.1.8 INTC Saved Level Mask Register (SLMASK)................................................. 10-114

10.5.1.9 INTC Interrupt Control Registers (ICRn).......................................................... 10-115

10.5.1.10 INTC IRQ Acknowledge Register (IRQIACK)................................................ 10-115

10.5.1.11 INTC FIQ Acknowledge Register (FIQIACK)................................................. 10-116

10.6 Functional Description............................................................................................... 10-116

10.6.1 Interrupt Recognition............................................................................................. 10-117

10.6.2 Interrupt Prioritization and Level Masking ........................................................... 10-117

10.6.3 Vector Generation During IACK........................................................................... 10-117

10.7 Initialization / Application Information..................................................................... 10-119

10.7.1 Typical Applications.............................................................................................. 10-119

10.7.2 Interrupt Service Routines..................................................................................... 10-119

10.7.3 Performance........................................................................................................... 10-121

Chapter 11

Miscellaneous Control Module (MCM)

11.1 Overview.................................................................................................................... 11-123

11.2 Features...................................................................................................................... 11-123

11.3 Memory Map / Register Definition ........................................................................... 11-123

11.3.1 Register Descriptions............................................................................................. 11-124

11.3.1.1 MCM Processor Core Type Register (PCT)...................................................... 11-124

11.3.1.2 MCM Device Revision Register (REV)............................................................ 11-125

Contents

Paragraph

Number

Title

Page

Number

MAC7100 Microcontroller Family Reference Manual, Rev. 2

Freescale Semiconductor xi

11.3.1.3 MCM XBS Master Configuration Register (AMC).......................................... 11-126

11.3.1.4 MCM XBS Slave Configuration Register (ASC).............................................. 11-126

11.3.1.5 MCM IPS On-Platform Module Configuration Register (IOPMC).................. 11-126

11.3.1.6 MCM Reset Status Register (MRSR)................................................................ 11-127

11.3.1.7 MCM Wake-up Control Register (MWCR) ...................................................... 11-128

11.3.1.8 MCM Software Watchdog Timer Control Register (MSWTCR)...................... 11-129

11.3.1.9 MCM Software Watchdog Timer Service Register (MSWTSR) ...................... 11-131

11.3.1.10 MCM Software Watchdog Timer Interrupt Register (MSWTIR) ..................... 11-132

11.3.1.11 MCM XBS Address Map Register (AAMR) .................................................... 11-132

11.3.1.12 MCM Core Fault Address Register (CFADR) .................................................. 11-135

11.3.1.13 MCM Core Fault Location Register (CFLOC) ................................................. 11-136

11.3.1.14 MCM Core Fault Attributes Register (CFATR) ................................................ 11-137

11.3.1.15 MCM Core Fault Data Register (CFDTR)........................................................ 11-138

11.4 Initialization / Application Information..................................................................... 11-138

11.4.1 Using The PCT And REV Registers...................................................................... 11-138

Chapter 12

Enhanced Direct Memory Access Controller Module (eDMA)

12.1 Overview.................................................................................................................... 12-141

12.2 Features...................................................................................................................... 12-143

12.3 Memory Map / Register Definition ........................................................................... 12-143

12.3.1 Register Descriptions............................................................................................. 12-144

12.3.1.1 eDMA Control Register (DMACR) .................................................................. 12-144

12.3.1.2 eDMA Error Status Register (DMAES)............................................................ 12-145

12.3.1.3 eDMA Enable Request Register (DMAERQ)................................................... 12-147

12.3.1.4 eDMA Enable Error Interrupt Registers (DMAEEI)......................................... 12-148

12.3.1.5 eDMA Set Enable Request Register (DMASERQ)........................................... 12-149

12.3.1.6 eDMA Clear Enable Request Register (DMACERQ)....................................... 12-149

12.3.1.7 eDMA Set Enable Error Interrupt Register (DMASEEI).................................. 12-150

12.3.1.8 eDMA Clear Enable Error Interrupt Register (DMACEEI).............................. 12-150

12.3.1.9 eDMA Clear Interrupt Request Register (DMACINT)..................................... 12-151

12.3.1.10 eDMA Clear Error Register (DMACERR) ....................................................... 12-152

12.3.1.11 eDMA Set START Bit Register (DMASSRT) .................................................. 12-152

12.3.1.12 eDMA Clear DONE Status Register (DMACDNE)..........................................12-153

12.3.1.13 eDMA Interrupt Request Register (DMAINT) ................................................. 12-153

12.3.1.14 eDMA Error Register (DMAERR).................................................................... 12-154

12.3.1.15 eDMA Channel Priority Registers (DCHPRIn) ................................................12-155

12.3.1.16 Transfer Control Descriptors (TCDn)................................................................ 12-156

12.4 Functional Description............................................................................................... 12-163

Contents

Paragraph

Number

Title

Page

Number

MAC7100 Microcontroller Family Reference Manual, Rev. 2

xii Freescale Semiconductor

12.4.1 eDMA Microarchitecture....................................................................................... 12-163

12.4.2 eDMA Basic Data Flow......................................................................................... 12-164

12.5 Initialization / Application Information..................................................................... 12-167

12.5.1 eDMA Transfer Control Descriptor Header File Example.................................... 12-167

12.5.2 eDMA Basic Channel Operation........................................................................... 12-168

12.5.3 eDMA Initialization Sequence............................................................................... 12-171

12.5.4 eDMA Programming Errors .................................................................................. 12-173

12.5.5 eDMA Arbitration Mode Considerations.............................................................. 12-173

12.5.5.1 Fixed-Priority Arbitration.................................................................................. 12-174

12.5.5.2 Round-Robin Arbitration................................................................................... 12-174

12.5.6 eDMA Transfers .................................................................................................... 12-174

12.5.6.1 Single Request................................................................................................... 12-174

12.5.6.2 Multiple Requests.............................................................................................. 12-175

12.5.6.3 Modulo Operation.............................................................................................. 12-176

12.5.7 eDMA TCDn Status Monitoring ........................................................................... 12-177

12.5.7.1 Minor Loop Complete ....................................................................................... 12-177

12.5.7.2 Active Channel TCDn Reads............................................................................. 12-178

12.5.7.3 Preemption Status.............................................................................................. 12-178

12.5.8 Channel Linking .................................................................................................... 12-178

12.5.9 Dynamic Channel Linking and Scatter/Gather Operation..................................... 12-180

Chapter 13

External Interface Module (EIM)

13.1 Overview.................................................................................................................... 13-181

13.2 Features...................................................................................................................... 13-182

13.3 Modes of Operation ................................................................................................... 13-182

13.4 Signal Description...................................................................................................... 13-183

13.4.1 CLKOUT............................................................................................................... 13-183

13.4.2 Address Bus (ADDR[21:0]) .................................................................................. 13-183

13.4.3 Data Bus (DATA[15:0])......................................................................................... 13-183

13.4.4 Read/Write Signal (R/W)....................................................................................... 13-184

13.4.5 Address Strobe (AS).............................................................................................. 13-184

13.4.6 Transfer Acknowledge (TA).................................................................................. 13-184

13.4.7 Output Enable (OE)............................................................................................... 13-184

13.4.8 Chip Selects (CS[2:0])........................................................................................... 13-184

13.4.9 Byte Selects (BS[1:0]) ........................................................................................... 13-184

13.5 Memory Map / Register Definition ........................................................................... 13-185

13.5.1 Register Descriptions............................................................................................. 13-185

13.5.1.1 EIM Chip Select Address Registers (CSARn) .................................................. 13-185

Contents

Paragraph

Number

Title

Page

Number

MAC7100 Microcontroller Family Reference Manual, Rev. 2

Freescale Semiconductor xiii

13.5.1.2 EIM Chip Select Mask Registers (CSMRn)...................................................... 13-186

13.5.1.3 EIM Chip Select Control Registers (CSCRn) ................................................... 13-187

13.6 Functional Description............................................................................................... 13-189

13.6.1 Chip Select Operation............................................................................................ 13-189

13.6.1.1 8- and 16-Bit Port Sizing................................................................................... 13-191

13.6.1.2 Global Chip Select............................................................................................. 13-191

13.6.2 External Bus Operation.......................................................................................... 13-192

13.6.2.1 Data Transfers.................................................................................................... 13-192

13.6.2.2 Bus Cycle Execution.......................................................................................... 13-193

13.6.2.3 Data Transfer Cycle States................................................................................. 13-194

13.6.2.4 Read Cycle......................................................................................................... 13-195

13.6.2.5 Write Cycle........................................................................................................ 13-196

13.6.2.6 Fast Termination Cycles .................................................................................... 13-197

13.6.2.7 Back-to-Back Bus Cycles.................................................................................. 13-198

13.6.2.8 Burst Cycles....................................................................................................... 13-198

13.7 Initialization / Application Information..................................................................... 13-201

13.7.1 Using Global Chip Select Mode............................................................................ 13-201

13.7.2 Configuring Chip Selects....................................................................................... 13-201

13.7.3 Dynamic Chip Select Configuration...................................................................... 13-202

Chapter 14

Cross-Bar Switch Module (XBS)

14.1 Overview.................................................................................................................... 14-203

14.2 Features...................................................................................................................... 14-203

14.3 Modes of Operation ................................................................................................... 14-204

14.4 Memory Map / Register Definition ........................................................................... 14-204

14.4.1 Register Descriptions............................................................................................. 14-205

14.4.1.1 XBS Priority Registers (PR_port)..................................................................... 14-205

14.4.1.2 XBS Control Registers (CR_port)..................................................................... 14-206

14.5 Functional Description............................................................................................... 14-207

14.5.1 Arbitration.............................................................................................................. 14-207

14.5.1.1 Fixed-Priority Operation.................................................................................... 14-207

14.5.1.2 Round-Robin Priority Operation ....................................................................... 14-208

14.5.1.3 Priority Assignment........................................................................................... 14-208

14.6 Initialization / Application Information..................................................................... 14-208

Contents

Paragraph

Number

Title

Page

Number

MAC7100 Microcontroller Family Reference Manual, Rev. 2

xiv Freescale Semiconductor

Chapter 15

Common Flash Module (CFM)

15.1 Overview.................................................................................................................... 15-209

15.2 Features...................................................................................................................... 15-211

15.3 Memory Map / Register Definition ........................................................................... 15-212

15.3.1 Register Descriptions............................................................................................. 15-214

15.3.1.1 CFM Module Configuration Register (CFMMCR)........................................... 15-214

15.3.1.2 CFM Clock Divider Register (CFMCLKD)...................................................... 15-216

15.3.1.3 CFM Security Register (CFMSEC)................................................................... 15-217

15.3.1.4 CFM Program Flash Protection Register (CFMPROT) .................................... 15-218

15.3.1.5 CFM Data Flash Protection Register (CFMDFPROT) ..................................... 15-220

15.3.1.6 CFM Program Flash Supervisor Access Register (CFMSACC)....................... 15-221

15.3.1.7 CFM Data Flash Supervisor Access Register (CFMDFSACC)........................ 15-221

15.3.1.8 CFM Program Flash Data Access Register (CFMDACC)................................ 15-222

15.3.1.9 CFM Data Flash Data Access Register (CFMDFDACC)................................. 15-223

15.3.1.10 CFM User Status Register (CFMUSTAT)......................................................... 15-223

15.3.1.11 CFM Command Register (CFMCMD).............................................................. 15-225

15.3.1.12 CFM Data Registers (CFMDATA1/0)............................................................... 15-225

15.3.1.13 CFM Disable Upper Block Register (CFMDISU) ............................................ 15-226

15.3.1.14 CFM Clock Select Register (CFMCLKSEL).................................................... 15-227

15.4 Functional Description............................................................................................... 15-227

15.4.1 Flash Normal Mode............................................................................................... 15-227

15.4.1.1 Read Operation.................................................................................................. 15-228

15.4.1.2 Write Operation .................................................................................................15-228

15.4.1.3 Command Launch Sequence ............................................................................. 15-228

15.4.1.4 Initializing the CFMCLKD Register................................................................. 15-229

15.4.1.5 Program, Erase, and Verify Operations ............................................................. 15-231

15.4.1.6 Flash Normal Mode Illegal Operations ............................................................. 15-246

15.4.1.7 Stop Mode.......................................................................................................... 15-246

15.4.2 Flash Security Operation ....................................................................................... 15-247

15.4.2.1 Backdoor Access Sequence............................................................................... 15-247

15.4.2.2 Blank Check....................................................................................................... 15-248

15.4.2.3 JTAG Lockout Recovery................................................................................... 15-248

15.5 Initialization / Application Information..................................................................... 15-248

15.5.1 Using The Data Signature Command.................................................................... 15-248

Contents

Paragraph

Number

Title

Page

Number

MAC7100 Microcontroller Family Reference Manual, Rev. 2

Freescale Semiconductor xv

Chapter 16

AMBA to IP Bus Bridge Module (AIPS)

16.1 Overview.................................................................................................................... 16-251

16.2 Features...................................................................................................................... 16-251

16.3 Modes of Operation ................................................................................................... 16-251

16.4 Memory Map / Register Definition ........................................................................... 16-253

16.4.1 Register Descriptions............................................................................................. 16-255

16.4.1.1 AIPS Master Protection Registers (MPRx) ....................................................... 16-255

16.4.1.2 AIPS Peripheral Access Control Registers (PACRx)........................................ 16-255

16.4.1.3 AIPS Off-Platform Peripheral Access Control Registers (OPACRx)................ 16-256

16.5 Functional Description............................................................................................... 16-257

16.5.1 Access Protections................................................................................................. 16-257

16.5.2 Access Support ...................................................................................................... 16-257

16.5.3 Read Cycles ........................................................................................................... 16-257

16.5.4 Write Cycles........................................................................................................... 16-257

16.5.5 Aborted Cycles ...................................................................................................... 16-257

16.6 Initialization / Application Information..................................................................... 16-258

Chapter 17

DMA Channel Multiplexer Module (DMAMux)

17.1 Overview.................................................................................................................... 17-259

17.2 Features...................................................................................................................... 17-259

17.3 Modes of Operation ................................................................................................... 17-260

17.4 Memory Map / Register Definition ........................................................................... 17-260

17.4.1 Register Descriptions............................................................................................. 17-261

17.4.1.1 DMAMux Channel Configuration Registers (CHCONFIGn)........................... 17-261

17.5 Functional Description............................................................................................... 17-262

17.5.1 eDMA Channels 0 to 7 .......................................................................................... 17-263

17.5.2 eDMA Channels 8 to 15 ........................................................................................ 17-264

17.5.3 Always Enabled DMA Request Sources............................................................... 17-265

17.6 Initialization / Application Information..................................................................... 17-266

17.6.1 Simple Setup.......................................................................................................... 17-266

17.6.1.1 Configure eDMA Channel 0 to Service eSCI_A Transmit Requests................ 17-266

17.6.2 Using the “Always Enabled” Feature to Periodically Drive GPIO Pins ............... 17-267

17.6.3 Disabling a Source................................................................................................. 17-267

17.6.4 Enable Source With Periodic Triggering............................................................... 17-268

17.6.4.1 DSPI Channel Configured For Periodic Service .............................................. 17-268

17.6.5 Enable Source With Transparent Triggering ......................................................... 17-268

Contents

Paragraph

Number

Title

Page

Number

MAC7100 Microcontroller Family Reference Manual, Rev. 2

xvi Freescale Semiconductor

17.6.5.1 DSPI Channel Configured for Immediate Service ........................................... 17-269

17.6.6 Switching DMA Request Source to eDMA Channel Assignment........................ 17-269

17.6.6.1 Switch eDMA Channel 9 from DSPI_A Transmit to eSCI_D Transmit........... 17-270

Chapter 18

Port Integration Module (PIM)

18.1 Overview.................................................................................................................... 18-271

18.2 Features...................................................................................................................... 18-273

18.3 Modes of Operation ................................................................................................... 18-273

18.4 Signal Description...................................................................................................... 18-273

18.5 Memory Map / Register Definition ........................................................................... 18-276

18.5.1 Register Descriptions............................................................................................. 18-286

18.5.1.1 PIM Port x Pin Configuration Registers (CONFIGn_x).................................... 18-286

18.5.1.2 PIM Port x Interrupt Flag Register (PORTIFR_x)............................................. 18-287

18.5.1.3 PIM Port x Data Register (PORTDATA_x)....................................................... 18-288

18.5.1.4 PIM Port x Input Register (PORTIR_x)............................................................. 18-288

18.5.1.5 PIM Port x Pin Data Registers (PINDATAn_x)................................................. 18-289

18.5.1.6 PIM Global Interrupt Status Register (GLBINT).............................................. 18-289

18.5.1.7 PIM Global Configuration Register (PIMCONFIG)......................................... 18-290

18.5.1.8 PIM Configure TDI Pin Register (CONFIG_TDI) ...........................................18-291

18.5.1.9 PIM Configure TDO Pin Register (CONFIG_TDO) ........................................ 18-292

18.5.1.10 PIM Configure TMS Pin Register (CONFIG_TMS) ........................................ 18-293

18.5.1.11 PIM Configure TCK Pin Register (CONFIG_TCK)......................................... 18-294

18.5.1.12 PIM Configure TA / AS Pin Register (CONFIG_TA)....................................... 18-294

18.5.1.13 PIM Port x/x 32-bit Input Registers (PORT32IR_xx)........................................ 18-295

18.6 Functional Description............................................................................................... 18-296

18.6.1 Reset....................................................................................................................... 18-296

18.6.2 Peripheral Mode..................................................................................................... 18-296

18.6.3 General Purpose Input Mode................................................................................. 18-298

18.6.3.1 Interrupts............................................................................................................ 18-299

18.6.4 General Purpose Output Mode .............................................................................. 18-301

18.7 Initialization / Application Information..................................................................... 18-303

18.7.1 Using a Pin in Peripheral Mode............................................................................. 18-303

18.7.1.1 PIM Example — Enable the I

2

C module .......................................................... 18-303

18.7.2 Using a Pin in GPIO Mode.................................................................................... 18-304

18.7.2.1 GPIO Mode Initialization.................................................................................. 18-304

18.7.2.2 PIM Example — Use PB[1:0] in GPO/GPI Mode............................................ 18-304

18.7.2.3 Accessing Data .................................................................................................. 18-305

18.7.2.4 Using Port Interrupts.......................................................................................... 18-309

Contents

Paragraph

Number

Title

Page

Number

MAC7100 Microcontroller Family Reference Manual, Rev. 2

Freescale Semiconductor xvii

18.7.3 PD2 / CLKOUT Configuration.............................................................................. 18-313

18.7.3.1 Using PD2 GPI Functionality............................................................................ 18-313

18.7.3.2 Using CLKOUT Functionality.......................................................................... 18-313

18.7.4 TA / AS Configuration........................................................................................... 18-314

18.7.5 E-ICE JTAG Port Configuration............................................................................ 18-314

18.7.6 Using the PIMCONFIG Register........................................................................... 18-314

18.7.6.1 Using the PORTHSEL Bit................................................................................. 18-315

18.7.6.2 Using the EIMCLKEN Bit ................................................................................ 18-315

18.7.7 Minimizing Power Consumption........................................................................... 18-315

Chapter 19

Analog-to-Digital Converter Module (ATD)

19.1 Overview.................................................................................................................... 19-317

19.2 Features...................................................................................................................... 19-318

19.3 Modes of Operation ................................................................................................... 19-319

19.4 Signal Description...................................................................................................... 19-319

19.4.1 ANn_x.................................................................................................................... 19-320

19.4.2 V

RH

/ V

RL

.............................................................................................................. 19-320

19.4.3 V

DD

A / V

SS

A......................................................................................................... 19-320

19.5 Memory Map / Register Definition ........................................................................... 19-320

19.5.1 Register Descriptions............................................................................................. 19-321

19.5.1.1 ATD Trigger Control Register (ATDTRIGCTL)............................................... 19-321

19.5.1.2 ATD External Trigger Channel Register (ATDETRIGCH)............................... 19-322

19.5.1.3 ATD Prescaler Register (ATDPRE)................................................................... 19-323

19.5.1.4 ATD Operating Mode Register (ATDMODE)................................................... 19-324

19.5.1.5 ATD Interrupt Register (ATDINT).................................................................... 19-325

19.5.1.6 ATD Flag Register (ATDFLAG) ....................................................................... 19-326

19.5.1.7 ATD Command Word Register (ATDCW)........................................................ 19-328

19.5.1.8 ATD Result Register (ATDRR)......................................................................... 19-330

19.6 Functional Description............................................................................................... 19-333

19.6.1 General................................................................................................................... 19-333

19.6.2 Analog Sub-Module............................................................................................... 19-333

19.6.2.1 Analog Input Multiplexer.................................................................................. 19-333

19.6.2.2 Sample Buffer Amplifier................................................................................... 19-333

19.6.2.3 Sample and Hold Machine................................................................................. 19-334

19.6.2.4 DAC................................................................................................................... 19-334

19.6.2.5 Comparator........................................................................................................ 19-334

19.6.2.6 Schmitt Trigger.................................................................................................. 19-334

19.6.3 Digital Sub-Module ............................................................................................... 19-334

Contents

Paragraph

Number

Title

Page

Number

MAC7100 Microcontroller Family Reference Manual, Rev. 2

xviii Freescale Semiconductor

19.6.3.1 Mode / Timing Control...................................................................................... 19-334

19.6.3.2 Clock Prescaler..................................................................................................19-334

19.6.3.3 IPS Bus Interface............................................................................................... 19-335

19.6.3.4 SYSTRIG0, SYSTRIG1, External Trigger Input..............................................19-335

19.6.4 ATD Operating Mode Details................................................................................ 19-335

19.6.4.1 ATD Normal Mode............................................................................................ 19-335

19.6.4.2 ATD Debug Mode.............................................................................................. 19-335

19.6.4.3 ATD Disabled Mode.......................................................................................... 19-336

19.6.4.4 ATD Doze Mode................................................................................................ 19-336

19.6.4.5 ATD Stop Mode................................................................................................. 19-337

19.6.5 Conversion process................................................................................................ 19-337

19.6.6 Reset....................................................................................................................... 19-340

19.6.7 Interrupts................................................................................................................ 19-340

19.7 Initialization / Application Information..................................................................... 19-341

19.7.1 ATD Initialization Sequence.................................................................................. 19-341

19.7.2 ATD Example 1 — Simple Conversion................................................................. 19-341

19.7.3 ATD Example 2 — Three Consecutive Conversions ............................................ 19-342

19.7.4 ATD Example 3 — Interrupted Continuous Conversion....................................... 19-343

19.7.5 ATD Example 4 — Edge Triggered Conversion................................................... 19-343

19.7.6 ATD Example 5 — Level Triggered Conversion.................................................. 19-344

19.7.7 ATD Example 6 — Using External Triggers......................................................... 19-345

19.7.8 ATD Example 7 — Using System Triggers........................................................... 19-345

19.7.9 Conversion Mechanism — CWCH, CWNF, CWGI and CWSC Bits................... 19-346

19.7.10 Conversion Mechanism — CWSL, CWSB and CW8 Bits................................... 19-347

19.7.11 Measuring Internal Reference Voltages................................................................. 19-348

Chapter 20

Enhanced Modular I/O Subsystem Module (eMIOS)

20.1 Overview.................................................................................................................... 20-351

20.2 Features...................................................................................................................... 20-352

20.3 Modes of Operation ................................................................................................... 20-352

20.4 Signal Description...................................................................................................... 20-353

20.4.1 emiosin — eMIOS Unified Channel n Input Signal.............................................. 20-353

20.4.2 emioson — eMIOS Unified Channel n Output Signal.......................................... 20-353

20.5 Memory Map / Register Definition ........................................................................... 20-353

20.5.1 Register Descriptions............................................................................................. 20-354

20.5.1.1 eMIOS Module Configuration Register (MCR)................................................ 20-354

20.5.1.2 eMIOS Global Flag Register (GFLAG)............................................................ 20-355

20.5.1.3 eMIOS Output Update Disable Register (OUDIS) ...........................................20-356

Contents

Paragraph

Number

Title

Page

Number

MAC7100 Microcontroller Family Reference Manual, Rev. 2

Freescale Semiconductor xix

20.5.1.4 eMIOS Channel Disable Register (UCDIS)...................................................... 20-356

20.5.1.5 eMIOS Channel A Data Registers (UCAn)....................................................... 20-357

20.5.1.6 eMIOS Channel B Data Registers (UCBn) ....................................................... 20-358

20.5.1.7 eMIOS Channel Counter Registers (UCCNTn)................................................ 20-359

20.5.1.8 eMIOS Channel Control Registers (UCCRn).................................................... 20-359

20.5.1.9 eMIOS Channel Status Registers (UCSRn) ...................................................... 20-363

20.6 Functional Description............................................................................................... 20-364

20.6.1 eMIOS Operating Mode Details............................................................................ 20-364

20.6.1.1 eMIOS Normal Mode........................................................................................ 20-364

20.6.1.2 eMIOS Debug Mode.......................................................................................... 20-365

20.6.1.3 eMIOS Disabled Mode...................................................................................... 20-365

20.6.1.4 eMIOS Doze Mode............................................................................................ 20-365

20.6.1.5 eMIOS Stop Mode............................................................................................. 20-365

20.6.2 IP Bus Interface Unit (BIU)................................................................................... 20-365

20.6.2.1 Effect of Debug Mode on the BIU.....................................................................20-366

20.6.3 Global Clock Prescaler (GCP) Submodule............................................................ 20-366

20.6.3.1 Effect of Debug Mode on the GCP.................................................................... 20-366

20.6.4 Unified Channel (UC)............................................................................................ 20-366

20.6.4.1 Effect of Debug Mode on Unified Channels..................................................... 20-366

20.6.5 Clock Prescaler (CP).............................................................................................. 20-367

20.6.6 Input Programmable Filter (IPF) ........................................................................... 20-368

20.6.7 UC Modes of Operation......................................................................................... 20-368

20.6.7.1 General Purpose Input/Output (GPIO) Mode.................................................... 20-369

20.6.7.2 Single Action Input Capture (SAIC) Mode....................................................... 20-369

20.6.7.3 Single Action Output Compare (SAOC) Mode................................................. 20-369

20.6.7.4 Input Pulse Width Measurement (IPWM) Mode............................................... 20-370

20.6.7.5 Input Period Measurement (IPM) Mode............................................................ 20-371

20.6.7.6 Double Action Output Compare (DAOC) Mode............................................... 20-372

20.6.7.7 Pulse/Edge Accumulation (PEA) Mode............................................................ 20-373

20.6.7.8 Pulse/Edge Counting (PEC) Mode.................................................................... 20-375

20.6.7.9 Quadrature Decode (QDEC) Mode................................................................... 20-376

20.6.7.10 Windowed Programmable Time Accumulation (WPTA) Mode........................ 20-378

20.6.7.11 Modulus Counter (MC) Mode........................................................................... 20-379

20.6.7.12 Output Pulse Width and Frequency Modulation (OPWFM) Mode................... 20-380

20.6.7.13 Center Aligned Output Pulse Width Modulation (OPWMC) Mode ................. 20-383

20.6.7.14 Output Pulse Width Modulation (OPWM) Mode.............................................. 20-385

20.6.7.15 Modulus Counter, Buffered (MCB) Mode ........................................................ 20-386

20.6.7.16

Output Pulse Width and Frequency Modulation, Buffered (OPWFMB) Mode

.. 20-389

20.6.7.17

Center Aligned Output Pulse Width Modulation, Buffered (OPWMCB) Mode

. 20-393

20.6.7.18 Output Pulse Width Modulation, Buffered (OPWMB) Mode........................... 20-398

20.7 Initialization / Application Information..................................................................... 20-401

Contents

Paragraph

Number

Title

Page

Number

MAC7100 Microcontroller Family Reference Manual, Rev. 2

xx Freescale Semiconductor

20.7.1 Changing UC Mode Considerations...................................................................... 20-402

20.7.2 Correlated Output Signal Generation .................................................................... 20-402

20.7.3 Time Base Generation............................................................................................ 20-402

Chapter 21

Enhanced Serial Communications Interface Module (eSCI)

21.1 Overview.................................................................................................................... 21-405

21.2 Features...................................................................................................................... 21-406

21.2.1 LIN support............................................................................................................ 21-406

21.3 Modes of Operation ................................................................................................... 21-407

21.4 Signal Description...................................................................................................... 21-407

21.4.1 TXD_x — SCI Transmit Data ............................................................................... 21-407

21.4.2 RXD_x — SCI Receive Data................................................................................. 21-407

21.5 Memory Map / Register Definition ........................................................................... 21-407

21.5.1 Register Descriptions............................................................................................. 21-408

21.5.1.1 eSCI Baud Rate Registers (ESCIBDH, ESCIBDH).......................................... 21-408

21.5.1.2 eSCI Control Registers (ESCICR1 through ESCICR4).................................... 21-409

21.5.1.3 eSCI Data Registers (ESCIDRH, ESCIDRL) ...................................................21-414

21.5.1.4 eSCI Status Registers (ESCISR1, ESCISR2).................................................... 21-415

21.5.1.5 LIN Status Registers (LINSTAT1, LINSTAT2)................................................. 21-417

21.5.1.6 LIN Control Registers (LINCTRL1, LINCTRL2, LINCTRL3)....................... 21-418

21.5.1.7 LIN TX Register (LINTX) ................................................................................ 21-420

21.5.1.8 LIN RX Register (LINRX)................................................................................ 21-423

21.5.1.9 LIN CRC Polynomial Registers (LINCRCP1, LINCRCP2)............................. 21-423

21.6 Functional Description............................................................................................... 21-424

21.6.1 Overview................................................................................................................ 21-424

21.6.2 Data Format ........................................................................................................... 21-424

21.6.3 Baud Rate Generation............................................................................................ 21-425

21.6.4 Transmitter............................................................................................................. 21-426

21.6.5 Transmitter Character Length................................................................................ 21-427

21.6.6 Character Transmission .........................................................................................21-427

21.6.7 Break Characters.................................................................................................... 21-428

21.6.8 Idle Characters....................................................................................................... 21-429

21.6.9 Fast Bit Error Detection......................................................................................... 21-429

21.6.10 Receiver................................................................................................................. 21-430

21.6.11 Receiver Character Length .................................................................................... 21-430

21.6.12 Character Reception............................................................................................... 21-431

21.6.13 Data Sampling........................................................................................................ 21-431

21.6.14 Framing Errors....................................................................................................... 21-435

Page is loading ...

NXP MAC7101 Reference guide

NXP MAC7101 Reference guide

Related papers

Other documents