Interlogix Industrial Gigabit Managed Switches (NS3552-8P-2S and NS3550-2T-8S) User manual

NS3552-8P-2S and

NS3550

-2T-8S User Manual

P/N 1072689-EN • REV D • ISS 25JAN19

Copyright

©

2019 United Technologies Corporation.

Interlogix is part of UTC

Climate, Controls & Security, a unit of United Technologies

Corporation

Trademarks and patents

Trade names used in this document may be trademarks or registered trademarks of the

manufacturers or vendors of the respective products.

Manufacturer

Interlogix

2955 Red Hill Avenue, Costa Mesa, CA 92626

-5923, USA

Authorized EU manufacturing representative:

UTC Fire & Security B.V.

Kelvinstraat 7, 6003 DH Weert, The Netherlands

Version

This document applies to

NS3552-8P-2S and NS3550-2T-8S.

FCC compliance

This device complies with part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) This device may not cause

harmful interference, and (2) this device

must accept any interference received, including interference that may cause undesired

operation.

FCC compliance

Class A:

This equipment has been tested and found to comply with the limits for a Class

A digital d

evice, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference when the equipment is

operated in a commercial environment. This equipment generates, uses, and can radiate

radio frequency

energy and, if not installed and used in accordance with the instruction

manual, may cause harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful interference in which case the

user will

be required to correct the interference at his own expense.

Canada

This Class A digital apparatus complies with CAN ICES

-003 (A)/NMB-3 (A).

Cet appareil numérique de la classe A est conforme à la norme CAN ICES

-003

(A)/NMB

-3 (A).

ACMA compliance

Notic

e! This is a Class A product. In a domestic environment this product may cause

radio interference in which case the user may be required to take adequate measures.

Certification

EU directives

This product and

- if applicable - the supplied accessories too are marked with "CE" and

comply therefore with the applicable harmonized European standards listed under the

EMC Directive 2014/30/EU, the RoHS Directive 2011/65/EU.

2012/19

/EU (WEEE directive): Products marked with this symbol cannot be disposed of

as unsorted municipal waste in the European Union. For proper recycling, return this

product to your local supplier upon the purchase of equivalent new equipment, or

dispose of it at designated collection points. For more information see:

www

.recyclethis.info.

Product warnings and

disclaimers

THESE PRODUCTS ARE INTENDED FOR SALE TO, AND INSTALLATION BY, AN

EXPERIENCED SECURITY PROFESSIONAL. UTC FIRE & SECURITY CANNOT

PROVIDE ANY ASSURANCE THAT ANY PERSON OR ENTITY BUYING ITS

PRODUCTS,

INCLUDING ANY “AUTHORIZED DEALER” OR “AUTHORIZED

RESELLER”

, IS PROPERLY TRAINED OR EXPERIENCED TO CORRECTLY INSTALL

SECURITY RELATED PRODUCTS.

For more information on warranty disclaimers and product safety information, please

check www.firesecurityproduct

s.com/policy/product-warning/ or scan the following code:

Contact information

and

manuals

For contact information

and manuals, go to: www.interlogix.com or

www.firesecurityproducts.com

NS3552-8P-2S and NS3550-2T-8S User Manual 1

Content

Important information 3

Chapter 1 Introduction 4

Package contents 4

Product description 5

Product features 10

Product specifications 14

Chapter 2 Installation 19

Hardware description 19

Installing the industrial managed switch 26

Cabling 29

Chapter 3 Switch management 35

Requirements 35

Management access overview 35

CLI mode management 36

Web management 38

SNMP-based network management 38

Chapter 4 Web configuration 40

Main web page 42

System 43

Simple Network Management Protocol (SNMP) 71

Port management 81

Link aggregation 88

VLAN 96

Spanning Tree Protocol (STP) 121

Multicast 139

Quality of Service (QoS) 162

Access Control Lists (ACL) 185

Authentication 199

Security 233

MAC address table 249

LLDP 255

Network diagnostics 268

Power over Ethernet (PoE) 272

Loop protection 284

RMON 286

Ring 295

Chapter 5 Command line interface 309

Accessing the CLI 309

Telnet login 309

2 NS3552-8P-2S and NS3550-2T-8S User Manual

Chapter 6 Command line mode 310

System Command 311

IP Command 317

Port Management Command 323

MAC Address Table Command 327

VLAN Configuration Command 330

Private VLAN Configuration Command 337

Security Command 339

Spanning Tree Protocol Command 385

Link Aggregation Command 394

Link Aggregation Control Protocol Command 396

LLDP Command 399

LLDP MED Command 403

EEE Command 407

Thermal Command 408

PoE Command (NS3552-8P-2S only) 409

Ethernet Virtual Connections Command 410

Ethernet Protection Switching Command 415

Maintainence entity End Point Command 416

Quality of Service Command 423

Mirror Command 436

Configuration Command 437

Firmware Command 438

UPnP Command 438

MVR Command 440

Voice VLAN Command 443

Ethernet Ring Protection Switching Command 448

Loop Protect Command 452

IPMC Command 454

VLAN Control List Command 462

SMTP Command 466

DIDO Command 468

Show Command 472

Chapter 7 Switch operation 477

Address table 477

Learning 477

Forwarding and filtering 477

Store-and-forward 477

Auto-negotiation 478

Chapter 8 Troubleshooting 479

Appendix A Networking connection 481

Glossary 483

NS3552-8P-2S and NS3550-2T-8S User Manual 3

Important information

Limitation of liability

To the maximum extent permitted by applicable law, in no event will UTCFS be liable

for any lost profits or business opportunities, loss of use, business interruption, loss of

data, or any other indirect, special, incidental, or consequential damages under any

theory of liability, whether based in contract, tort, negligence, product liability, or

otherwise. Because some jurisdictions do not allow the exclusion or limitation of liability

for consequential or incidental damages the preceding limitation may not apply to you.

In any event the total liability of UTCFS shall not exceed the purchase price of the

product. The foregoing limitation will apply to the maximum extent permitted by

applicable law, regardless of whether UTCFS has been advised of the possibility of

such damages and regardless of whether any remedy fails of its essential purpose.

Installation in accordance with this manual, applicable codes, and the instructions of the

authority having jurisdiction is mandatory.

While every precaution has been taken during the preparation of this manual to ensure

the accuracy of its contents, UTCFS assumes no responsibility for errors or omissions.

Advisory messages

Advisory messages alert you to conditions or practices that can cause unwanted

results. The advisory messages used in this document are shown and described below.

WARNING: Warning messages advise you of hazards that could result in injury or loss

of life. They tell you which actions to take or to avoid in order to prevent the injury or

loss of life.

Caution: Caution messages advise you of possible equipment damage. They tell you

which actions to take or to avoid in order to prevent damage.

Note: Note messages advise you of the possible loss of time or effort. They describe

how to avoid the loss. Notes are also used to point out important information that you

should read.

4 NS3552-8P-2S and NS3550-2T-8S User Manual

Chapter 1

Introduction

The description of the IFS NS3552-8P-2S model is as follows:

 Industrial L2+ 8-port 10/100/1000T 802.3at PoE

 + 2-port 100/1000X SFP managed switch

The description of the IFS NS3550-2T-8S model is as follows:

 Industrial L2+ 8-port Gigabit Fiber (SFP) managed switch

 + 2-port 10/100/1000T

Unless specified, the terms “industrial managed switch” and “industrial managed

switches” mentioned in this user manual refers to the NS3552-8P-2S and/or NS3550-

2T-8S.

Package contents

Open the box of the industrial managed switch and carefully unpack it. The box should

contain the following items:

 The industrial managed switch × 1

 Quick installation guide × 1

 CD with user manual × 1

 DIN rail kit x 1

 Wall mounting kit x 1

 RS232 console cable x 1

 SFP dust-proof cap x 2

 RJ45 dust-proof cap x 9

If any of these are missing or damaged, contact your dealer immediately. If possible,

retain the carton including the original packing materials for repacking the product in

case there is a need to return it to us for repair.

Chapter 1: Introduction

NS3552-8P-2S and NS3550-2T-8S User Manual 5

Product description

Environmentally hardened design

With IP30 aluminum case protection, the industrial managed switches provide a high

level of immunity against electromagnetic interference and heavy electrical surges

which are usually found on plant floors or in curb-side traffic control cabinets. It also

possesses an integrated power supply source with a wide range of voltages for

worldwide high availability applications requiring dual or backup power inputs. Being

able to operate under the temperature range from -40 to 75°C, the industrial managed

switch can be placed in almost any difficult environment.

Digital input and digital output for external alarm

The industrial managed switches support digital input and digital output on their front

panels. The external alarm allows users to use the digital input to detect an external

device’s status (such as a door intrusion detector), and send an event alarm to the

administrators. The digital output can be used to alarm the administrators if the

industrial managed switch port is link-down, link-up, or power-dead.

Chapter 1: Introduction

6 NS3552-8P-2S and NS3550-2T-8S User Manual

Robust layer 2 features

The industrial managed switches can be programmed for advanced switch

management functions such as dynamic port link aggregation, Q-in-Q VLAN, Multiple

Spanning Tree Protocol (MSTP), layer 2 to layer 4 QoS, bandwidth control, and IGMP /

MLD snooping. The industrial managed switch allows the operation of a high-speed

trunk combining multiple ports. The NS3552-8P-2S provides 802.1Q tagged VLAN and

a maximum of 255 VLAN groups. The NS3552-8P-2S not only allows the operation of a

high-speed trunk combining multiple ports, but also supports connection fail-over.

Efficient management

For efficient management, the industrial managed switches are equipped with console,

web, and SNMP management interfaces. With the built-in web-based management

interface, the industrial switches offers an easy-to-use, platform-independent

management and configuration facility. The NS3552-8P-2S supports standard Simple

Network Management Protocol (SNMP) and can be managed by any management

software based on the standard SNMP v1 or v2 protocol. For text-based management

mode, the NS3552-8P-2S can be accessed via Telnet and the console port. Moreover,

the industrial managed switches offer secure management remotely by supporting

SSH, SSL, and SNMP v3 connections where the packet content can be encrypted at

each session.

Powerful security

The industrial switches offer comprehensive layer 2 to layer 4 access control list (ACL)

for enforcing security to the edge. It can be used to restrict to network access by

denying packets based on source and destination IP address, TCP/UDP port number,

or defined typical network applications. Its protection mechanism also comprises

802.1x port-based and MAC-based user and device authentication. With the private

VLAN function, communication between edge ports can be prevented to ensure user

privacy. The industrial switches also provide DHCP snooping, IP Source Guard and

Dynamic ARP Inspection functions to prevent IP snooping from attack and discard ARP

packets with invalid MAC addresses. The network administrator can now construct

highly secured corporate networks in considerably less time and with less effort than

before.

Chapter 1: Introduction

NS3552-8P-2S and NS3550-2T-8S User Manual 7

Flexible and extendable solution

The industrial managed switches feature 100BASE-FX and 1000BASE-SX/LX SFP

(Small Form-factor Pluggable) fiber-optic modules, meaning the administrator now can

flexibly choose the suitable SFP transceiver according to the transmission distance or

the transmission speed required to extend the network efficiently. The distance can be

extended from 550 m to 2 km (multi-mode fiber) up to above 10/20/30/40/50/70 km

(single-mode fiber or WDM fiber). They are well suited for applications within enterprise

data centers and distributions.

PoE functions for PD management (NS3552-8P-2S only)

Redundant ring, fast recovery for surveillance systems

The NS3552-8P-2S supports redundant ring technology and features strong, rapid self-

recovery capability to prevent interruptions and external intrusions. It incorporates

advanced ITU-T G.8032 ERPS (Ethernet Ring Protection Switching) technology,

Spanning Tree Protocol (802.1s MSTP), and redundant power input system into the

customer’s industrial automation network to enhance system reliability and uptime in

harsh factory environments. In a certain simple ring network, the recovery time of data

link can be as fast as 20 ms.

Chapter 1: Introduction

8 NS3552-8P-2S and NS3550-2T-8S User Manual

Intelligent powered device alive check

The NS3552-8P-2S can be configured to monitor connected powered device (PD)

status in real time via a ping action. After the PD stops working and responding, the

industrial managed switch resumes the PoE port power and puts the PD back to work.

TheNS3552-8P-2S greatly enhances the network reliability through the PoE port

resetting the PD’s power source and reducing the administrator management burden.

PoE schedule for energy saving

Under the trend of energy saving worldwide and contributing to environmental

protection, the NS3552-8P-2S can effectively control the power supply in addition to its

capability of providing high Watt power. The “PoE schedule” function helps you to

enable or disable PoE power feeding for each PoE port during specified time intervals,

and is a powerful function to help SMBs or enterprises save power and money.

Chapter 1: Introduction

NS3552-8P-2S and NS3550-2T-8S User Manual 9

IPv6/IPv4 full-function secure switch for building automation networking

The NS3552-8P-2S is the ideal solution to fulfilling the demand of IPv6 management

gigabit Ethernet switches, especially in the industrial-hardened environment. It supports

both IPv4 and IPv6 protocols, advanced layer 2 to layer 4 data switching and

redundancy, QoS traffic control, network access control and authentication, and secure

management features to protect customer’s industrial and building automation network

connectivity with reliable switching recovery capability that is suitable for implementing

fault tolerant and mesh network architectures.

Perfect integration solution for outdoor IP PoE camera and NVR system

The NS3552-8P-2S provides eight 10/100/1000 Mbps 802.3af/at PoE ports and offers

sufficient PoE power for eight PoE IP cameras at the same time. In addition, with the 2-

Port 100/1000Base-X SFP interfaces, the NS3552-8P-2S can connect to a core fiber

switch and send video streams to NVRs and monitor centers. Through the high

performance switch architecture, the NS3552-8P-2S facilitates the recorded video files

from the eight PoE IP cameras to be saved in the NVR systems.

Furthermore, the NVR systems can be controlled and monitored both in the local LAN

and the remote site via Internet. The NS3552-8P-2S undoubtedly brings an ideal,

secure surveillance system at a lower total cost.

Chapter 1: Introduction

10 NS3552-8P-2S and NS3550-2T-8S User Manual

Product features

Physical port – NS3552-8P-2S

• Eight 10/100/1000BASE-T gigabit Ethernet RJ45 ports with IEEE 802.3af / 802.3at

PoE injector.

• Two 100/1000BASE-X mini-GBIC/SFP slots, SFP type auto detection.

• One RJ45 console interface for basic management and setup.

Physical port – NS3550-2T-8S

• Two 10/100/1000BASE-T gigabit Ethernet RJ45 ports.

• Eight 100/1000BASE-X mini-GBIC/SFP slots, SFP type auto detection.

• One RJ45 console interface for basic management and setup.

Power over Ethernet (NS3552-8P-2S only)

• Complies with IEEE 802.3af / IEEE 802.3at Power over Ethernet / End-Span PSE.

• Complies with IEEE 802.3af Power over Ethernet / End-Span PSE.

• Up to four ports of IEEE 802.3af/IEEE 802.3at devices powered.

• Supports PoE power up to 15.4 W or 30.8 W for each PoE port.

• Auto detects powered device (PD).

• Circuit protection prevents power interference between ports.

• Remote power feeding up to 100 m.

• PoE management:

• IEEE 802.3af and IEEE 802.3at mode switch control

• Total PoE power budget control

• Per port PoE function enable/disable

• PoE admin-mode control

• PoE port power feeding priority

• Per PoE port power limitation

• PD classification detection

• Intelligent PoE features:

• Temperature threshold control

• PoE usage threshold control

• PD alive check

• PoE schedule

• PD power recycling schedule

Chapter 1: Introduction

NS3552-8P-2S and NS3550-2T-8S User Manual 11

Industrial case and installation

• IP30 aluminum case

• DIN-rail and wall-mount design

• 48 VDC redundant power with polarity reverse protect function

• Supports 6000 VDC EFT protection for power line

• Supports Ethernet ESD protection for 6000 VDC

• -40 to 75°C operating temperature

Digital input and digital output

• Two Digital Inputs (DI)

• Two Digital Outputs (DO)

• Integrates sensors into auto alarm system

• Transfers alarm to IP network via email and SNMP trap

Layer 2 features

• Prevents packet loss with back pressure (half-duplex) and IEEE 802.3x PAUSE

frame flow control (full-duplex).

• High performance of Store-and-Forward architecture and runt/CRC filtering

eliminates erroneous packets to optimize the network bandwidth.

Storm control support:

• Broadcast / Multicast / Unknown-Unicast

Supports VLAN

• IEEE 802.1Q tagged VLAN

• Up to 255 VLANs groups out of 4094 VLAN IDs

• Provider bridging (VLAN Q-in-Q) support (IEEE 802.1ad)

• Private VLAN Edge (PVE)

• Protocol-based VLAN

• MAC-based VLAN

• Voice VLAN

Supports STP

• STP, IEEE 802.1D Spanning Tree Protocol

• RSTP, IEEE 802.1w Rapid Spanning Tree Protocol

• MSTP, IEEE 802.1s Multiple Spanning Tree Protocol, spanning tree by VLAN

• BPDU Guard

Chapter 1: Introduction

12 NS3552-8P-2S and NS3550-2T-8S User Manual

Supports link aggregation

• IEEE 802.3ad Link Aggregation Control Protocol (LACP)

• Cisco ether-channel (static trunk)

• Maximum five trunk groups, up to eight ports per trunk group

• Up to 16 Gbps bandwidth (duplex mode)

Provides port mirror (many-to-1)

Port mirroring to monitor the incoming or outgoing traffic on a particular port

Loop protection to avoid broadcast loops

Supports Ethernet Ring Protection Switching (ERPS)

Quality of Service

• Ingress shaper and egress rate limit per port bandwidth control

• Eight priority queues on all switch ports

• Traffic classification:

- IEEE 802.1p CoS

- TOS / DSCP / IP Precedence of IPv4/IPv6 packets

- IP TCP/UDP port number

- Typical network application

• Strict priority and Weighted Round Robin (WRR) CoS policies

• Supports QoS and In/Out bandwidth control on each port

• Traffic-policing policies on the switch port

• DSCP remarking

Multicast

• Supports IGMP snooping v1, v2, and v3

• Supports MLD snooping v1 and v2

• Querier mode support

• IGMP snooping port filtering

• MLD snooping port filtering

• Multicast VLAN Registration (MVR) support

Security

• Authentication

− IEEE 802.1x Port-Based / MAC-Based network access authentication

− Built-in RADIUS client to co-operate with the RADIUS servers

Chapter 1: Introduction

NS3552-8P-2S and NS3550-2T-8S User Manual 13

− TACACS+ login users access authentication

− RADIUS / TACACS+ users access authentication

• IP-based Access Control List (ACL)

− MAC-based ACL

• Source MAC / IP address binding

• DHCP snooping to filter distrusted DHCP messages

• Dynamic ARP inspection discards ARP packets with invalid MAC addresses to IP

address binding.

• IP source guard prevents IP spoofing attacks.

• Auto DoS rule to defend against DoS attacks.

• IP address access management to prevent unauthorized intruders.

Management

• Switch management interfaces:

− Console / Telnet Command Line Interface

− Web switch management

− SNMP v1 and v2c switch management

− SSH / SSL and SNMP v3 secure access

• IPv6 IP address/NTP/DNS management

• Built-in Trivial File Transfer Protocol (TFTP) client

• System maintenance

- Firmware upload/download via HTTP / TFTP

- Reset button for system reboot or reset to factory default

• Four RMON groups (history, statistics, alarms, and events)

• IPv6 IP address / NTP / DNS management and ICMPv6

• BOOTP and DHCP for IP address assignment

• DHCP relay

• DHCP Option 82

• User privilege levels control

• NTP (Network Time Protocol)

• Link Layer Discovery Protocol (LLDP) and LLDP-MED

• SFP-DDM (Digital Diagnostic Monitor)

• Smart discovery utility for deploy management

• Network diagnostic

Chapter 1: Introduction

14 NS3552-8P-2S and NS3550-2T-8S User Manual

− Cable diagnostic technology provides the mechanism to detect and report

potential cabling issues

Product specifications

Model Name

NS3552

-8P-2S NS3550-2T-8S

Hardware Specification

s

Copper

Ports

Two

10/100/1000BASE-T RJ45s

Two 10/100/1000BASE-T Ethernet

interface

SFP

+ Slots

Eight 1000BASE

-SX/LX/BX SFP

interfaces

Compatible with 1000BASE

-FX SFP

Eight 100/1000BASE-SX/LX mini-

GBIC SFP slots

Console Port

1 x RS

-232 to RJ45

serial port (115200,

8, N, 1)

Switch Architecture

Stor

e-and-Forward Store-and-Forward

Switch

Fabric

20

Gbps / non-blocking 20 Gbps / non-blocking

Throughput

14.8

Mpps @ 64 bytes 14.8 Mpps

Address Table

8

K entries, automatic source address

learning and ag

ing

8K entries, automatic source

address learning and aging

Share

d Data Buffer

4 Mbits

Flow Control

IEEE 802.3x

pause frame for full-duplex

Back pressure for

half-duplex

IEEE 802.3x pause frame for full-

duplex

Back pressure for half-duplex

Jumbo Frame

9

K bytes 9K bytes

Reset Button

< 5 seconds: System reboot

>

5 seconds: Factory Default

< 5 seconds: System reboot

> 5 seconds: Factory Default

Enclosure

IP30 aluminum case

Installation

DIN rail kit and wall

-mount kit DIN rail kit and wall-mount kit

Connector

Removable 6

-pin terminal block for

power input

Pin 1/2 for Power 1, Pin 3/4 for fault

alarm, Pin 5/6 for Power 2

Removable 6

-pin terminal block for

DI/DO interface

Pin 1/2 for DI 1 & 2, Pin 3/4 for DO 1 &

2, Pin 5/6 for GND

Alarm

One relay output for power failure.

Alarm relay current carry ability:

1A @ 24

VDC

One relay output for power failure.

Alarm relay current carry ability:

1A @ 24 VDC

Digital Input

Two Digital Inputs (DI)

Chapter 1: Introduction

NS3552-8P-2S and NS3550-2T-8S User Manual 15

Level 0: -24~2.1 V (±0.1 V)

Level 1: 2.1~24 V

(±0.1 V)

Input load to 24 VDC, 10 mA max.

Digital Output

Two Digital Outputs (DO)

Open collector to 24 VDC, 100 mA

max.

LED

System:

Power 1 (Green)

Power 2 (Green)

Fault Alarm (Green)

Ring (Green)

Ring Owner (Green)

Per 10/100/1000T RJ45 Ports:

PoE in-use (Orange)

1000 LNK/ACT (Green)

Per SFP Interface:

100 LNK/ACT (Orange)

1000 LNK/ACT (Green)

System:

Power 1 (Green)

Power 2 (Green)

Fault Alarm (Green)

Ring (Green)

Ring Owner (Green)

Per 10/100/1000T RJ45 Ports:

10/100 LNK/ACT (Orange)

1000 LNK/ACT (Green)

Per SFP Interface:

100 LNK/ACT (Orange)

1000 LNK/ACT (Green)

Dimensions

152 x 107

x 72 mm 152 x 107 x 72 mm

Weight

1.684 kg

1.036 kg

Power Requirement

D

C 48 V

DC 12 to 48 V, 24 VAC power

adapter

Power

Consumption

At/31.9

W / 108.78 BTU (full loading

without PoE function)

306

W / 1043.46 BTU (full loading with

PoE function)

13.92 W / 47.76 BTU (full loading)

ESD Protection

6K VDC

EFT Protection

6K VDC

Power over Ethernet

PoE Standard

IEEE 8

02.3af/802.3at PoE / PSE

PoE Power

Supply Type

End

-span

PoE Power Output

IEEE 802.3af Standard

Per port 56 VDC, 350 mA. Max.

15.4 W.

IEEE 802.3at Standard

Per port 56 VDC, 590 mA. Max. 30

W.

Power Pin Assignment

End

-span: 1/2(-), 3/6(+)

PoE Power Budget

27

0 W maximum (depending on power

input)

Chapter 1: Introduction

16 NS3552-8P-2S and NS3550-2T-8S User Manual

Max. number of Class 2

PD

8

Max. number of Class 3

PD

8

Max. number of Class 4

PD

8

Layer 2

Functions

Basic Management

Interfaces

Console; Telnet; Web browser; SNMP

v1, v2c

Web browser; Remote Telnet,

SNMP v1, v2c

Secure

Management

Interfaces

SSH, SSL, SNMP v3

Port

Configuration

Po

rt disable / enable

Auto

-negotiation 10/100/1000Mbps full

and half duplex mode selection

Flow

control disable/enable

Power saving mode control

Port disable / enable

Auto-negotiation 10/100/1000Mbps

full and half duplex mode selection.

Auto-detection / Forced

100/1000Mbps SFP Fiber

transceiver speed.

Flow control disable/enable

Power saving mode control

Port Status

Display each port’s speed duplex mode,

link status,

flow control status, auto-

neg

otiation status, trunk status.

Display each port’s speed duplex

mode, link status, flow control status,

auto-negotiation status, trunk status.

Port Mirroring

TX / RX / both

1

-to-1 monitor

TX / RX / both

Many-to-1 monitor

VLAN

802.1Q tagged

-based VLAN, up to 255

VLAN groups

Q

-in-Q tunneling

Private VLAN

Edge (PVE)

MAC

-based VLAN

Protocol

-based VLAN

Voice VLAN

MVR (Multicast VLAN Registration)

U

p to 255 VLAN groups, out of 4094

VLAN IDs

802.1Q tagged-based VLAN, up to

255 VLAN groups

Q-in-Q tunneling

Private VLAN

MAC-based VLAN

Protocol-based VLAN

Voice VLAN

MVR (Multicast VLAN Registration)

Up to 255 VLAN groups, out of 4095

VLAN ID

Link Aggregation

IEEE 802.3ad LACP

/static trunk

Five groups with eight

ports per trunk

IEEE 802.3ad LACP/static trunk

Five groups with 10 ports per trunk

QoS

Traffic classification based,

s

trict priority

and WRR

8

-level priority for switching

–

Port number

–

802.1p priority

–

802.1Q VLAN tag

–

DSCP/ToS field in IP packet

Traffic classification based, strict

priority and WRR

8-level priority for switching

– Port number

– 802.1p priority

– 802.1Q VLAN tag

– DSCP/ToS field in IP packet

IGMP Snooping

IGMP (v1/v2

/v3) snooping, up to 255

multicast

groups

IGMP (v1/v2/v3) snooping, up to 255

multicast groups

Chapter 1: Introduction

NS3552-8P-2S and NS3550-2T-8S User Manual 17

IGMP querier mode support

MLD Snooping

MLD (v1/v2)

snooping, up to 255

multicast

groups

MLD

querier mode support

MLD (v1/v2) snooping, up to 255

multicast groups

MLD querier mode support

Access Control List

IP

-based ACL / MAC-based ACL

Up to

123 entries

IP-based ACL / MAC-based ACL

Up to 256 entries

Bandwidth Control

Per port bandwidth control

–

Ingress: 500 Kbps~1000 Mbps

–

Egress: 500 Kbps~1000 Mbps

Per port bandwidth control

– Ingress: 500 Kbps~1000 Mbps

– Egress: 500 Kbps~1000 Mbps

Standards Conformance

Regulation Compliance

FCC Part 15 Class A, CE

Stability Testing

IEC60068

-2-32 (Free fall)

IEC60068

-2-27 (Shock)

IEC60068

-2-6 (Vibration)

IEC60068-2-32 (Free fall)

IEC60068-2-27 (Shock)

IEC60068-2-6 (Vibration)

Standards Compliance

IEEE

802.3 10BASE-T

IEEE

802.3u 100BASE-TX/100BASE-

FX

IEEE

802.3z Gigabit SX/LX

IEE

E 802.3ab Gigabit 1000T

IEEE 802.3x flow control and back

pressure

IEEE 802.3ad port trunk with LACP

IEEE 802.1D Spanning Tree Protocol

IEEE 802.1w Rapid Spanning Tree

Protocol

IEEE 802.1s Multiple Spanning Tree

Protocol

IEEE 802.1p Class of Service

IEEE 802.1Q VLAN tagging

IEEE 802.1X Port Authentication

Network Control

IEEE 802.1ab LLDP

IEEE 802.3af Power over Ethernet

IEEE 802.3at Power

over Ethernet Plus

RFC 768 UDP

RFC 793 TFTP

RFC 791 IP

RFC 792 ICMP

RFC 2068 HTTP

RFC 1112 IGMP v1

RFC 2236 IGMP v2

IEEE 802.3 10Base-T

IEEE 802.3u 100Base-TX /

100Base-FX

IEEE 802.3z Gigabit SX/LX

IEEE 802.3ab Gigabit 1000T

IEEE 802.3x Flow Control and Back

pressure

IEEE 802.3ad Port trunk with LACP

IEEE 802.1D Spanning Tree

Protocol

IEEE 802.1w Rapid Spanning Tree

Protocol

IEEE 802.1s Multiple Spanning Tree

Protocol

IEEE 802.1p Class of service

IEEE 802.1Q VLAN Tagging

IEEE 802.1x Port Authentication

Network Control

IEEE 802.1ab LLDP

SNMP MIBs

RFC 1213 MIB

-II

IF

-MIB

RFC 1493 Bridge MIB

RFC 1643 Ethernet MIB

RFC-1213 MIB-II

RFC-2236 IGMPv2

RFC-2710 MLDv1

RFC-3376 IGMPv3

Chapter 1: Introduction

18 NS3552-8P-2S and NS3550-2T-8S User Manual

RFC 2863 Interface MIB

RFC 2665 Ether

-Like MIB

RFC 2819 RMON MIB (Groups 1, 2, 3

and 9)

RFC 2737 Entity MIB

RFC 2618 RADIUS Client MIB

RFC 2933 IG

MP-STD-MIB

RFC 3411 SNMP

-Frameworks-MIB

IEEE 802.1X PAE

LLDP

MAU

-MIB

RFC-2879 RMON 1, 2, 3, 9

RFC-1493 Bridge MIB

RFC-1643 Ethernet MIB

RFC-2863 Interface MIB

RFC-2665 Ether-Like MIB

RFC-2819 RMON MIB (Group 1, 2,

3 and 9)

RFC-2737 Entity MIB

RFC-2618 RADIUS Client MIB

RFC3411 SNMP-Frameworks-MIB

IEEE 802.1X PAE

IF-MIB

LLDP

MAU-MIB

Environment

Operating

Temperature:

-40 to 75°C

Relative Humidity:

5 to 95% (non-

condensing)

Temperature: -40 to 75°C

Relative Humidity: 5 to 95% (non-

condensing)

Storage

Temperature:

-40 to 85°C

Relative Humidity:

5 to 95% (non-

condensing)

Temperature: -40 to 85°C

Relative Humidity: 5 to 95% (non-

condensing)

Page is loading ...

Interlogix Industrial Gigabit Managed Switches (NS3552-8P-2S and NS3550-2T-8S) User manual

Related papers

Other documents