Astonica 50105607 User manual

Astonica
Brand
Astonica
Model
50105607
Type
User manual

This manual is also suitable for

IF YOU HAVE ANY PROBLEMS OR QUESTIONS CONCERNING THIS PRODUCT,
DO NOT RETURN IT TO YOUR RETAILER, CONTACT CUSTOMER SERVICE AT
1-888-424-3354
180107rev1
Read the instructions and precautions before use of this product
Please keep this instruction manual for future reference
IF YOU HAVE ANY PROBLEMS OR QUESTIONS CONCERNING THIS PRODUCT,
DO NOT RETURN IT TO YOUR RETAILER, CONTACT CONSUMER SUPPORT AT
1-888-424-3354
OR
IF YOU ARE A STORE MANAGER OR EMPLOYEE IN NEED OF ASSISTANCE CALL
1-888-851-5569
PLEASE HAVE YOUR STORE NUMBER READY
Limited Warranty
World Factory, Inc.
®
Products for Home Use
World Factory, Inc.
®
(Seller) warrants to the original Buyer only, that each Astonica
®
Product will be
free from defects in material and workmanship for a period of one (1) year from date of purchase.
SELLER’S SOLE OBLIGATION AND BUYER’S EXCLUSIVE REMEDY UNDER THIS LIMITED
WARRANTY SHALL BE THE REPAIR OR REPLACEMENT OF PARTS, WITHOUT CHARGE, WHICH
ARE DEFECTIVE IN MATERIAL OR WORKMANSHIP. ANY PARTS AS DETERMINED BY THE
SELLER WHICH HAVE BEEN MISUSED; ABUSED OR DAMAGED EITHER DIRECTLY OR INDIRECTLY
FROM REPAIRS OR ALTERATIONS ATTEMPTED BY UNAUTHORIZED PERSONS; IMPROPER
MAINTENANCE, NEGLECT OR ACCIDENT ARE NOT COVERED BY THIS LIMITED WARRANTY. This
warranty does not apply to damage, heat-induced coloration changes, scratching or alteration due to
normal use or weathering. To make a claim under this Limited Warranty, you must return the complete
product with proof of purchase, transportation prepaid, to any World Factory, Inc.
®
authorized service
center. Call 1-888-424-3354 for the location of the nearest authorized service center.
Additional Limitations
THIS LIMITED WARRANTY DOES NOT APPLY TO ACCESSORY OR CONSUMABLE ITEMS RELATED
TO THIS PRODUCT. ALL IMPLIED WARRANTIES SHALL BE LIMITED IN DURATION TO ONE (1)
YEAR FROM DATE OF PURCHASE. IN NO EVENT SHALL SELLER BE LIABLE FOR ANY
INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO LIABILITY FOR
LOSS OF PROFITS, ARISING FROM THE SALE OR USE OF THIS PRODUCT.
If any provision of this Limited Warranty is for any reason held to be invalid or unenforceable, such
provision shall not affect any other provision herein, this Limited Warranty shall be construed as if
such invalid and/or unenforceable provision had never been contained herein.
This Warranty contains the entire agreement between Seller and Buyer and supersedes any and all
prior agreements, arrangements, or understandings between the parties relating to product warranty.
®
Made in China
©2007 World Factory, Inc.
Distributed by:
World Factory, Inc.
Coppell, TX 75019
Model No: 50105607
Ashelina 3 - Piece Bistro Set
Instruction Manual
Due to ongoing product development
the actual product or products may vary from
the illustrations or photos shown within this manual.
Table Assembly
1.(SEE FIGURE 1) Place table top (A)
upside down on a flat non-scratch
surface.
2.Using a flat head screw driver,
thread studs (G) into the three holes
at bottom of table top (A).
3.Attach table legs to studs on bottom
of table top with flat washers (J) and
hex nuts (K).
4.Do not fully tighten fasteners.
5.(SEE FIGURE 2) Position center ring (C)
over studs (H) in table legs (B) and secure
with flat washers (J) and hex nuts (K).
6.Turn table upright on a flat level surface
and tighten all fasteners.
Chair Assembly
1.(SEE FIGURE 3) Using a flat head
screw driver, thread studs (I) into
holes in bottom of chair backs (D) and
studs (H) in chairs seats (E) until seated.
2.Insert studs in chair backs (D) through
holes in chair seats (E) and secure
with flat washers (J) and hex nuts (K).
3.Fit one chair leg (F) over studs in
bottom of chair seat (E) and secure
with flat washers (J) and hex nuts (K).
Repeat for the other legs.
REQUIRED TOOLS (NOT INCLUDED)
Flat Drive Screwdriver
PARTS & HARDWARE LIST
ASSEMBLY INSTRUCTIONS
PART # DESCRIPTION QUANTITY
A 1Table Top
B 3Table Leg
C 1Center Ring
D 2Chair Back
Chair SeatE 2
Chair LegF 8
Stud, 8mm x 30G 3
Flat Washer, 8mm
I 4
Stud, 8mm x 25H 19
Hex Nut, 8mm
J 26
A
B
C
D
E
F
G
H
J
K
Carefully remove the contents from the package. If any parts are missing do not
attempt to use the product until they have been obtained and correctly installed.
CAUTION: Do not over tighten fasteners.
CAUTION: Do not over tighten fasteners.
IF YOU HAVE ANY PROBLEMS OR QUESTIONS CONCERNING THIS PRODUCT,
DO NOT RETURN IT TO YOUR RETAILER. CONTACT CUSTOMER SERVICE AT
1-888-424-3354.
J
K
J
K
J
K
B
H
H
A
B
B
B
J
J
J
K
K
K
G
G
G
C
Figure 1
I
Figure 2
Figure 3
F
E
D
K
J
I
K
J
H
K
Stud, 8mm x 35
26
H
2
1
  • Page 1 1
  • Page 2 2

Astonica 50105607 User manual

Astonica
Brand
Astonica
Model
50105607
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents