Precautions
• Before installing the mounting bracket, confirm whether the delivered product is
identical to the product that you have ordered.
• Because SOL type is a mounting bracket for AC motor and gearhead, do not use them
for other objects.
• Install the AC motor and gearhead using the tightening torque shown the table below.
• Operate the motor after installing the mounting bracket (SOL type).
INSTALLATION MANUAL
Mounting Brackets
SOL type for AC Motors
and Gearheads
Thank you for purchasing ORIENTAL MOTOR
products.
Please read this manual thoroughly before
installing the mounting bracket, and always
keep the manual where it is readily
accessible.
Mounting bracket
models
SOL0U04
SOL2U08
SOL3U10
SOL4U10
SOL5UA
Size and tightening torque of mounting screws
for AC motor and gearhead
No.4-40UNC
5.6 ~ 8.3 lb-in (0.64 ~ 0.96 N·m)
No.8-32UNC
12.1 ~ 19.1 lb-in (1.4 ~ 2.2 N·m)
No.10-24UNC
17.4 ~ 34.7 lb-in (2 ~ 4 N·m)
No.10-24UNC
17.4 ~ 34.7 lb-in (2 ~ 4 N·m)
1/4-20UNC
43.4 ~ 60.8 lb-in (5 ~ 7 N·m)
Size of mounting screws
for mounting bracket
No.6-32UNC
No.10-24UNC
No.10-24UNC
No.10-24UNC
No.12-24UNC or M6 P1.0
∗Gearhead can be installed at every right angle.
Mounting screw
Washer
How to fix on equipment
Copyright ORIENTAL MOTOR CO., LTD. 2003
ORIENTAL MOTOR U.S.A. CORP.
Technical Support Line Tel:(800)468-3982
Available from 7:30 AM to 5:00 PM, P.S.T.
E-mail: [email protected]
www.orientalmotor.com
ORIENTAL MOTOR CO., LTD.
Headquarters
Tokyo, Japan
Tel:(03)3835-0684 Fax:(03)3835-1890
• Characteristics, specifications and dimensions are subject to change without notice.
• Please contact your nearest ORIENTAL MOTOR office for further information.
Printed on Recycled Paper
Specifications
Please make sure to use
washers and fix with
mounting screws.
(Mounting screws are not
provided with the
mounting bracket.)
AC motor
Gearhead
Mounting screw
Mounting bracket
∗
∗
Installation
Install the AC motor and gearhead using the mounting screws provided with the
gearhead.
HM-9141-3
Precautions
• Before installing the mounting bracket, confirm whether the delivered product is
identical to the product that you have ordered.
• Because SOL type is a mounting bracket for geared stepping motor, do not use them
for other objects.
• Operate the geared stepping motor after installing the mounting bracket (SOL type).
INSTALLATION MANUAL
Mounting Brackets
SOL type for Geared
Stepping Motors
Thank you for purchasing ORIENTAL MOTOR
products.
Please read this manual thoroughly before
installing the mounting bracket, and always
keep the manual where it is readily
accessible.
Mounting
bracket
models
SOL0A-A
SOL0B-A
SOL2A-A
SOL5B-A
Frame size
of motor
1.65 in.
(42 mm) sq.
1.65 in.
(42 mm) sq.
2.36 in.
(60 mm) sq.
3.54 in.
(90 mm) sq.
Geared stepping motor
-
TH geared type
-
TH geared type
-
TH geared type
5-phase
stepping motor
-
TH geared type
TH geared type
(CSK series)
TH geared type
TH geared type
(CSK series)
TH geared type
2-phase
stepping motor
SH geared type
-
-
-
SH geared type
-
Size of mounting
screws for motor
No.4-40UNC
Length 0.4 in.
M4 P0.7
Length 10 mm
No.8-32UNC
Length 0.5 in.
M4 P0.7
Length 12 mm
No.8-32UNC
Length 0.5 in.
M8 P1.25
Length 20 mm
Size of mounting
screws for
mounting bracket
No.8-32UNC
or M4 P0.7
No.8-32UNC
or M4 P0.7
No.10-24UNC
or M5 P0.5
M6 P1.0
∗Geared stepping motor can be installed at every right angle.
Mounting screw
Washer
How to fix on equipment
Copyright ORIENTAL MOTOR CO., LTD. 2003
ORIENTAL MOTOR U.S.A. CORP.
Technical Support Line Tel:(800)468-3982
Available from 7:30 AM to 5:00 PM, P.S.T.
E-mail: [email protected]
www.orientalmotor.com
ORIENTAL MOTOR CO., LTD.
Headquarters
Tokyo, Japan
Tel:(03)3835-0684 Fax:(03)3835-1890
• Characteristics, specifications and dimensions are subject to change without notice.
• Please contact your nearest ORIENTAL MOTOR office for further information.
Printed on Recycled Paper
Specifications
Please make sure to use
washers and fix with
mounting screws.
(Mounting screws are not
provided with the
mounting bracket.)
Mounting bracket
Mounting screw
Geared stepping
motor
∗
∗
Installation
Install the geared stepping motor using the mounting screws (Mounting screws are not
provided).
HM-9141-3
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Oriental motor GFV6G100 Operating instructions
-
-
-
Oriental motor 4IK25GN-AW2TU / 4GN7.5RAA Operating instructions
-
-
-
Oriental motor T-MB520-B-A Operating instructions
-
-
Oriental motor 5IK40GN-AW2U / 5GN15RH Operating instructions
-
