Toro 21in Heavy-Duty Rear Bagger Lawn Mower User manual

Brand: Toro

Model: 21in Heavy-Duty Rear Bagger Lawn Mower

Category: Lawnmowers

Type: User manual

Form No. 3357-388 Rev B

21in Heavy-Duty Rear Bagger

Lawn Mower

Model No. 22189 —Serial No. 270000001 and Up

Warning

CALIFORNIA

Pr oposition 65 W ar ning

T he engine exhaust fr om this pr oduct

contains chemicals kno wn to the State of

Calif or nia to cause cancer , bir th defects, or

other r epr oducti v e har m.

Important: T his engine is not equipped

with a spar k ar r ester muf ﬂer . It is a

violation of Calif or nia Public R esource Code

Section 4442 to use or operate the engine

on an y f or est-co v er ed, br ush-co v er ed, or

g rass-co v er ed land. Other states or federal

ar eas may ha v e similar la ws.

T his spark ignition system complies with Canadian

ICES-002

T he enclosed Engine Owner’ s Man ual is

supplied f or inf or mation r egarding the US

En vir onmental Pr otection Agency (EP A) and

the Calif or nia Emission Contr ol R egulation of

emission systems, maintenance, and w ar ranty .

R eplacements may be order ed thr ough the

engine man uf actur er .

Introduction

R ead this infor mation carefully to lear n ho w to

operate and maintain y our product properly and

to a v oid injur y and product damag e . Y ou are

responsible for operating the product properly

and safely .

Y ou ma y contact T oro directly at www .T oro .com

for product and accessor y infor mation, help

ﬁnding a dealer , or to register y our product.

W henev er y ou need ser vice , g en uine T oro par ts ,

or additional infor mation, contact an A uthorized

Ser vice Dealer or T oro Customer Ser vice and ha v e

the model and serial n umbers of y our product

ready . Figure 1 identiﬁes the location of the model

and serial n umbers on the product. W rite the

n umbers in the space pro vided.

Figure 1

1. Model and serial number plate

Model No.

Serial No.

T his man ual identiﬁes potential hazards and has

safety messag es identiﬁed b y the safety aler t

symbol ( Figure 2 ), whic h signals a hazard that ma y

cause serious injur y or death if y ou do not follo w

the recommended precautions .

Figure 2

1. Safety alert symbol

T his man ual uses 2 w ords to highlight infor mation.

Impor tant calls attention to special mec hanical

infor mation and Note emphasizes g eneral

infor mation w or th y of special attention.

8111 Lyndale Avenue South

Bloomington, MN 55420

Printed in the USA.

Contents

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

General La wn Mo w er Safety . . . . . . . . . . . . . . . . 4

Safety and Instr uctional Decals . . . . . . . . . . . . 6

Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

1 Installing the Handle . . . . . . . . . . . . . . . . . . . . . . . . . 7

2 Installing the Fuel T ank and the

Fuel Line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

3 Filling the Crankcase with Oil . . . . . . . . . . . . 8

Product Ov er view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Chec king the Engine Oil Lev el . . . . . . . . . . . 10

Filling the Fuel T ank with

Gasoline . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Star ting the Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Stopping the Engine . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Operating the Blade . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Operating the T raction Dri v e . . . . . . . . . . . . . 13

Chec king the Blade Brak e

Clutc h . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Adjusting the Cutting Height . . . . . . . . . . . . . 14

Using the Grass Bag . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Operating Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

R ecommended Maintenance

Sc hedule(s) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Lubricating the Pi v ot Ar ms . . . . . . . . . . . . . . . . 18

Lubricating the Gear Case . . . . . . . . . . . . . . . . . . 18

Engine Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Ser vicing the Air Filter . . . . . . . . . . . . . . . . . . . . . . . 18

Changing the Engine Oil . . . . . . . . . . . . . . . . . . . . 19

Changing the Oil Filter . . . . . . . . . . . . . . . . . . . . . . 19

Ser vicing the Spark Plug . . . . . . . . . . . . . . . . . . . . 20

Fuel System Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Emptying the Fuel T ank and

Cleaning the Fuel

Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Dri v e System Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . 21

Adjusting the Self-propel

Dri v e . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Ser vicing the W heels . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Controls System Maintenance . . . . . . . . . . . . . . . . . . . . 22

Adjusting the Blade Brak e

Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Blade Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Maintaining the Cutting Blade . . . . . . . . . . . . 23

Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Cleaning under the Mo w er

Housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Cleaning the Blade Brak e Clutc h

Shield . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Storag e . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Pre paring the Fuel System . . . . . . . . . . . . . . . . . . 26

Pre paring the Engine . . . . . . . . . . . . . . . . . . . . . . . . . 26

General Infor mation . . . . . . . . . . . . . . . . . . . . . . . . . 26

R emo ving the La wn Mo w er from

Storag e . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

T roubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Safety

T his la wn mo w er meets or ex ceeds the

CPSC blade safety r equir ements f or

w alk-behind r otar y la wn mo w er s and the

B71.4 speciﬁcations of the American National

Standards Institute in ef fect at the time of

pr oduction.

Impr oper l y using or maintaining this la wn

mo w er can r esult in injur y . T o r educe the

potential f or injur y , compl y with these safety

instr uctions.

T oro designed and tested this la wn mo w er for to

offer reasonably safe ser vice; ho w ev er , f ailur e to

compl y with the f ollo wing instr uctions may

r esult in per sonal injur y .

Engine exhaust contains carbon mono xide,

an odor less, deadl y poison that can kill y ou.

Do not r un the engine indoor s or in an

enclosed ar ea.

T o ensur e maximum safety , best perf or mance,

and to gain kno wledge of the pr oduct, it is

essential that y ou and an y other operator of

the la wn mo w er r ead and under stand the

contents of this man ual bef or e the engine is

ev er star ted. P ay par ticular attention to the

safety aler t symbol ( Figur e 2 ) which means

Caution, W ar ning , or Danger—“per sonal

safety instr uction.” R ead and under stand the

instr uction because it has to do with safety .

F ailur e to compl y with the instr uction may

r esult in per sonal injur y .

General Lawn Mower Safety

T his la wn mo w er is capable of amputating hands

and feet and of thro wing objects . F ailure to

obser v e the follo wing safety instr uctions could

result in serious injur y or death.

T he follo wing instr uctions are from the

ANSI/OPEI B71.4-2004 standard.

Training

• R ead the Operator’ s Man ual and other training

material. If the operator(s) or mec hanic(s) can

not read English it is the o wner’ s responsibility

to explain this material to them.

• Become familiar with the safe operation of the

equipment, operator controls , and safety signs .

• All operators and mec hanics should be trained.

T he o wner is responsible for training the users .

• Nev er let c hildren or untrained people operate

or ser vice the equipment. Local regulations

ma y restrict the ag e of the operator .

• T he o wner/user can prev ent and is responsible

for accidents or injuries occur ring to

themselv es , other people , or proper ty .

Preparation

• Only use accessories and attac hments appro v ed

b y the man ufacturer .

• W ear appropriate clothing including hard hat,

safety glasses , and ear protection. Long hair ,

loose clothing or jew elr y ma y g et tangled in

mo ving par ts .

• Inspect the area where the equipment is to be

used and remo v e all objects suc h as roc ks , to ys

and wire whic h can be thro wn b y the mac hine .

• Use extra care when handling g asoline and

other fuels . T hey are ﬂammable and v apors

are explosi v e .

– Use only an appro v ed container .

– Nev er remo v e g as cap or add fuel with

engine r unning . Allo w engine to cool

before refueling . Do not smok e .

– Nev er refuel or drain the mac hine indoors .

• Chec k that operator’ s presence controls ,

safety switc hes and shields are attac hed and

functioning properly . Do not operate unless

they are functioning properly .

Operation

• Nev er r un an engine in an enclosed area.

• Only operate in g ood light, k ee ping a w a y from

holes and hidden hazards .

• Only star t engine from the operator’ s position.

• Be sure of y our footing, especially when

bac king up . W alk, don ’ t r un. Nev er operate

on w et g rass . R educed footing could cause

slipping .

• Slo w do wn and use extra care on hillsides . Be

sure to tra v el side to side on hillsides . T urf

conditions can affect the mac hine’ s stability .

Use caution while operating near drop-offs .

• Do not operate the la wn mo w er without either

the g rass catc her or the guard in place .

• Do not c hang e the engine g o v er nor setting or

o v erspeed the engine .

• Stop on lev el g round and shut off engine

before lea ving the operator’ s position for

any reason including emptying the catc her or

unclog ging the c hute .

• Stop equipment and inspect blade after striking

objects or if an abnor mal vibration occurs .

Mak e necessar y re pairs before resuming

operations .

• K ee p hands and feet a w a y from the cutting

units .

• Look behind and do wn before bac king up to

be sure of a clear path.

• K ee p pets and b ystanders a w a y .

• Slo w do wn and use caution when crossing

roads and sidew alks . Stop blade if y ou are not

mo wing .

• Be a w are of the mo w er disc harg e direction and

do not point it at any one .

• Do not operate the mo w er under the inﬂuence

of alcohol or dr ugs .

• Use care when loading or unloading the

mac hine into a trailer or tr uc k.

• Use care when approac hing blind cor ners ,

shr ubs , trees , or other objects that ma y obscure

vision.

Maintenance and Storage

• Stop engine and disconnect spark plug wire .

W ait for all mo v ement to stop before adjusting,

cleaning or re pairing .

• Clean g rass and debris from cutting unit, dri v e ,

m ufﬂer , and engine to help prev ent ﬁres . Clean

up oil or fuel spillag e .

• Let engine cool before storing and do not store

near ﬂame .

• Shut off fuel while storing or transpor ting . Do

not store fuel near ﬂames or drain indoors .

• Nev er allo w untrained personnel to ser vice

mac hine .

• R emo v e spark plug wire before making any

re pairs .

• Use care when c hec king blade . W rap the blade

or w ear glo v es , and use caution when ser vicing

them. Only re place blade . Nev er straighten

or w eld it.

• K ee p hands and feet a w a y from mo ving par ts .

If possible , do not mak e adjustments with the

engine r unning .

• K ee p all par ts in g ood w orking condition and

all hardw are tightened. R e place all w or n or

damag ed decals .

Safety and Instructional Decals

Safety decals and instr uctions are easily visible to the operator and are located near any

area of potential dang er . R e place any decal that is damag ed or lost.

Manufacturer’s Mark

1. Indicates the blade is identied as a part from the original

machine manufacturer.

43-8480

68-7410

98-4387

1. Warning—wear hearing protection.

110-2114

110-4977

1. Thrown object hazard—do not operate the mower without a

bag in place.

110-4989

Setup

Loose Parts

Use the chart below to verify that all parts have been shipped.

Step

Description

Qty.

Use

Handle

Bolt (5/16 x 7/8 inch)

Bolt (5/16 x 1-1/2 inches)

Washer

Locknut (5/16 inch)

Cable tie

Install the handle.

Self-tapping screw

Fuel tank

Install the fuel tank and fuel line.

No parts required

–

Fill the crankcase with oil.

Note: Deter mine the left and right sides of the

mac hine from the nor mal operating position.

Step

Installing the Handle

Parts needed for this step:

Handle

Bolt (5/16 x 7/8 inch)

Bolt (5/16 x 1-1/2 inches)

Washer

Locknut (5/16 inch)

Cable tie

Procedure

1. Mount the handle to the mo w er housing with

2 bolts (5/16 x 7/8 inc h), 2 bolts(5/16 x 1-1/2

inc hes), 4 w ashers , and 4 loc kn uts ( Figure 3 ).

Figure 3

1. Housing

3. Bolt (5/16 x 1-1/2 inches),

washer, and locknut

2. Handle

4. Bolt (5/16 x 7/8 inch),

washer, and locknut

Note: Install the w ashers with the cup side

facing the handle .

Note: Y ou can adjust the handle height for

more comfor table operation. Securing the

lo w er handle end in the upper hole lo w ers the

handle; securing the lo w er handle end in the

lo w er hole raises the handle .

2. Use the cable ties pro vided to secure the

control cables to the handle .

Step

Installing the Fuel Tank and

the Fuel Line

Parts needed for this step:

Self-tapping screw

Fuel tank

Procedure

1. Slide the end of the fuel line onto the elbo w

ﬁtting ( Figure 4 ).

Figure 4

1. Fuel tank 3. Fuel line

2. Elbow tting 4. Fuel line clamp

2. Secure the fuel line in place with the fuel line

clamp ( Figure 4 ).

3. Slide the plastic clips on the front of the fuel

tank onto the fuel tank mount ( Figure 5 ).

Figure 5

1. Plastic clip (2)

4. Secure the bottom of the fuel tank to the

fuel tank brac k et b y installing the self-tapping

screws from the bottom. Do not o v er tighten

the scr ews.

Step

Filling the Crankcase with

Oil

No Parts Required

Procedure

T he engine crankcase is shipped without oil. Y ou

m ust ﬁll it with appro ximately 30 oz. (0.88 L) of

oil before star ting the engine . R efer to Chec king

the Engine Oil Lev el in Operation , pag e 10 for oil

speciﬁcations and instr uctions .

Product Overview

Figure 6

1. Handle

8. Oil ll/dipstick (not shown)

2. Blade control bar 9. Cutting height lever

3. Control bar lock 10. Spark plug

4. Ground speed control lever 11. Air lter

5. Traction control bar 12. Oil lter

6. Fuel tank 13. Grass bag

7. Starter handle 14. Throttle control lever

Controls

T he blade control bar , control bar loc k, g round

speed control lev er , throttle control lev er , and

traction control bar are on the upper handle as

sho wn in ( Figure 7 ).

Figure 7

1. Blade control bar 4. Throttle control lever

2. Control bar lock 5. Traction control bar

3. Ground speed control lever

T he throttle settings are sho wn in ( Figure 8 ).

Figure 8

1. Choke 3. Slow

2. Fast 4. Stop

Operation

Note: Deter mine the left and right sides of the

mac hine from the nor mal operating position.

Eac h time before y ou mo w , mak e sure that the

self-propel dri v e and the blade control bar operate

properly . W hen y ou release the blade control bar ,

the blade and self-propel dri v e should stop . If they

do not, contact an A uthorized Ser vice Dealer .

T his machine pr oduces sound lev els in

ex cess of 85dB A at the operator’ s ear and

can cause hearing loss thr ough extended

periods of exposur e.

W ear hearing pr otection when operating

this machine.

Figure 9

1. Warning—wear hearing protection.

Checking the Engine Oil

Level

Initially , ﬁll the crankcase with 30 ounces (0.88

liters) of oil. Use only high-quality SAE 30 or SAE

10W30 w eight deterg ent oil that has the American

P etroleum Institute (API) ser vice classiﬁcation SF ,

SG , SH, or SJ .

Oil Capacity

With oil lter

30 ounces (0.88 L)

Without oil lter

24 ounces (0.70 L)

Before eac h use , ensure that the oil lev el is betw een

the Add and Full marks on the dipstic k ( Figure 10 ).

Figure 10

1. Dipstick 3. Add

2. Full

Note: W hen the crankcase is empty , pour

about 3/4 of the crankcase capacity of oil in

the crankcase , then follo w the procedure in this

section.

1. Mo v e the la wn mo w er to a lev el surface .

2. Clean around the dipstic k ( Figure 10 ).

3. R emo v e the dipstic k b y rotating the cap

countercloc kwise and pulling it out.

4. Wipe the dipstic k clean with a clean cloth.

5. Inser t the dipstic k into the ﬁller nec k, but do

not scr ew it in .

6. R emo v e the dipstic k and read the oil lev el on

the dipstic k ( Figure 10 ).

7. If the oil lev el reading is belo w the Add mark

on the dipstic k, slo wly pour only enough oil

into the ﬁller hole to raise the oil lev el to the

Full mark on the dipstic k.

Important: Do not o v erﬁll the crankcase

with oil and r un the engine; engine dama ge

will r esult. Drain the ex cess oil until the oil

lev el on the dipstick r eads Full.

8. Inser t the dipstic k into the ﬁller nec k and

rotate the cap cloc kwise until it is tight.

Filling the Fuel Tank with

Gasoline

F or best results , use clean, fresh, lead-free g asoline

with an octane rating of 87 or higher . T o ensure

freshness , purc hase only the quantity of g asoline

that y ou expect to use in 30 da ys . Using unleaded

g asoline results in few er combustion de posits and

long er engine life . Y ou ma y use leaded g asoline if

unleaded g asoline is not a v ailable .

Important: Do not add oil to the gasoline.

Important: Do not use methanol, gasoline

containing methanol, gasohol containing

mor e than 10% ethanol, pr emium gasoline, or

white gas. Using these fuels can dama ge the

engine’ s fuel system.

Important: Do not use gasoline that has

been stor ed since the last mo wing season or

longer .

In cer tain conditions, gasoline is extr emel y

ﬂamma ble and highl y explosi v e. A ﬁr e or

explosion fr om gasoline can bur n y ou and

other s and can dama ge pr oper ty .

• Fill the fuel tank outdoor s, in an open

ar ea, and when the engine is cold. W ipe

up an y gasoline that spills.

• Do not ﬁll the fuel tank completel y full.

Add gasoline to the fuel tank until the

lev el is 1/4 to 1/2 in. (6 to 13 mm) belo w

the bottom of the ﬁller neck. T his empty

space in the tank allo ws the gasoline to

expand.

• Nev er smok e when handling gasoline,

and stay a w ay fr om an open ﬂame or

wher e a spar k may ignite the gasoline

fumes.

• Stor e gasoline in an appr o v ed fuel

container and k eep it out of the r each of

childr en.

• Nev er buy mor e than a 30-day suppl y of

gasoline.

W hen fueling , under cer tain circumstances,

a static charge can dev elop , igniting the

gasoline. A ﬁr e or explosion fr om gasoline

can bur n y ou and other s and dama ge

pr oper ty .

• Al w ays place gasoline container s on

the g r ound and a w ay fr om y our v ehicle

bef or e ﬁlling .

• Do not ﬁll gasoline container s inside

a v ehicle or on a tr uck or trailer bed

because interior car pets or plastic tr uck

bed liner s may insulate the container and

slo w the loss of an y static charge.

• W hen practical, r emo v e

gasoline-po w er ed equipment fr om

the tr uck or trailer and r efuel the

equipment with its wheels on the r ound.

• If this is not possible, then r efuel such

equipment on a tr uck or trailer fr om a

por ta ble container , not fr om a gasoline

dispenser nozzle.

• If y ou must use a gasoline dispenser

nozzle, k eep the nozzle in contact with

the rim of the fuel tank or container

opening at all times until fueling is

complete.

Use a fuel stabilizer/conditioner regularly during

operation and storag e . A stabilizer/conditioner

cleans the engine during operation and prev ents

gum-lik e v ar nish de posits from for ming in the

engine during periods of storag e .

Important: Do not use fuel additi v es other

than a fuel sta biliz er/conditioner . Do not use

fuel sta biliz er s with an alcohol base such as

ethanol, methanol, or isopr opanol.

1. Clean around the fuel tank cap ( Figure 11 ).

Figure 11

1. Oil ll/dipstick 3. Air cleaner

2. Fuel tank cap

2. R emo v e the cap from the tank.

3. Fill the fuel tank with unleaded g asoline to

within 1/4 to 1/2 inc h (6 to 13 mm) from the

top of the tank. Do not ﬁll into the ﬁller

neck.

Important: Do not ﬁll the tank mor e

than 1/4 inch (6 mm) fr om the top of the

tank because the gasoline must ha v e r oom

to expand.

4. Install the fuel tank cap and wipe up any spilled

g asoline .

Starting the Engine

1. Connect the wire to the spark plug ( Figure 11 ).

2. Open the fuel v alv e ( Figure 22 )

3. Mo v e the throttle control lev er to the Chok e

position ( Figure 8 ).

4. Mo v e the g round speed control lev er to the

Neutral (N) position.

5. Pull the star ter handle lightly until y ou feel

resistance , then pull it shar ply .

6. R egulate the throttle and the g round speed

control as desired when the engine star ts .

Note: If the engine fails to star t after 3 pulls ,

re peat ste ps 3 through 6 .

Stopping the Engine

1. Mo v e the throttle control to the Stop position.

2. Disconnect the wire from the spark plug if

y ou do not use the la wn mo w er or lea v e it

unattended.

Operating the Blade

Engaging the Blade

W hen y ou star t y our engine , the blade does not

tur n. Y ou m ust eng ag e the blade to mo w .

1. Push the control bar loc k forw ard ( Figure 12 ).

Figure 12

2. Pull the blade control bar to the handle and

hold it ( Figure 13 ).

Figure 13

Disengaging the Blade

R elease the blade control bar .

Important: W hen y ou r elease the blade

contr ol bar , the blade should stop within 3

seconds. If it does not stop pr oper l y , stop

using y our mo w er immediatel y and contact an

Authoriz ed Ser vice Dealer .

Operating the Traction

Drive

Engaging the Traction Drive

1. R elease the traction control bar ( Figure 14 ).

Figure 14

2. Mo v e the g round speed control lev er to the

desired g ear position.

3. Squeeze the traction control bar ag ainst the

handle ( Figure 15 ).

Figure 15

Disengaging the Traction Drive

R elease the traction control bar .

Checking the Blade Brake

Clutch

Chec k the blade control bar before eac h use

to ensure that the blade brak e clutc h system is

operating properly .

1. Install the empty g rass bag on the disc harg e

tunnel.

2. Star t the engine .

3. Pull the blade control bar to the nor mal blade

eng ag ed position. T he bag should begin to

inﬂate , indicating that the blade is eng ag ed and

rotating .

4. R elease the blade control bar . If the bag does

not immediately deﬂate , it indicates that the

blade is still rotating . T he blade brak e clutc h

ma y be deteriorating, and, if ignored, could

result in an unsafe operating condition. Ha v e

the la wn mo w er inspected and ser viced b y an

A uthorized Ser vice Dealer .

If the blade brak e clutch system is

inoperati v e, the blade will contin ue to r otate

when y ou r elease the blade contr ol bail.

Contact with blade could occur , causing

serious injur y .

• Check the blade brak e clutch operation

bef or e each use.

• Nev er use a mo w er equipped with a

blade brak e clutch that has an inoperati v e

safety system.

• T ak e y our mo w er to an Authoriz ed

Ser vice Dealer f or r epair if the safety

system f ails to operate pr oper l y .

Adjusting the Cutting

Height

Eac h wheel is adjusted indi vidually with a wheel

height adjustment lev er . Cutting heights are

1-1/4 inc hes (32 mm), 1-3/4 inc hes (44 mm),

2-1/4 inc hes (57 mm), 2-3/4 inc hes (70 mm),

3-1/4 inc hes (83 mm), and 3-3/4 inc hes (95 mm).

Adjusting the cutting height lev er s could

bring y our hands into contact with a mo ving

blade and r esult in serious injur y .

• Stop the engine and w ait f or all

mo v ement to stop bef or e adjusting the

cutting height.

• Do not put y our ﬁnger s under the

housing when adjusting the cutting

height.

1. Pull the wheel height adjustment lev er to w ard

the wheel ( Figure 16 ) and mo v e it to the

desired setting .

Figure 16

1. Wheel height adjustment lever

2. R elease the wheel height adjustment lev er and

seat it securely in the notc h.

3. Adjust all the wheels to the same cutting height

setting .

Using the Grass Bag

Installing the Grass Bag

1. W ait for all mo ving par ts to stop .

2. Raise and hold up the rear door ( Figure 17 ).

Figure 17

1. Rear door

3. Install the bag on the bag mounting posts

( Figure 18 ).

Figure 18

1. Bag mounting posts

4. Lo w er the rear door .

Removing the Grass Bag

T o remo v e the bag, rev erse the ste ps abo v e .

T he mo w er can thr o w g rass clippings and

other objects thr ough an open discharge

tunnel. Objects thr o wn with enough f orce

could cause serious per sonal injur y or death

to the operator or bystander .

Do not operate the mo w er without a g rass

ba g installed.

Mowing with the Grass Bag

A w or n g rass ba g could allo w small stones

and other similar de bris to be thr o wn in the

operator’ s or bystander’ s dir ection and r esult

in serious per sonal injur y or death to the

operator or bystander s.

Check the g rass ba g fr equentl y . If it is

dama ged, install a new T or o r eplacement

ba g .

Operating Tips

General Tips

• Maintain a shar p blade throughout the cutting

season. P eriodically ﬁle do wn nic ks on the

blade .

• R e place the blade when necessar y with an

original T oro re placement blade .

• Mo w only dr y g rass or lea v es . W et g rass and

lea v es tend to clump on the yard and can cause

the mo w er to plug or the engine to stall.

W et g rass or lea v es can cause serious

injur y if y ou slip and contact the blade.

Mo w onl y in dr y conditions.

• Clean under the mo w er housing after eac h

mo wing . See Cleaning under the Mo w er

Housing .

• K ee p the engine in g ood r unning condition.

• Set the engine speed to the fastest position for

the best cutting results .

Operating a mo w er with its engine

r unning at a speed g r eater than the

f actor y setting can cause the mo w er to

thr o w a par t of the blade or engine into

the operator’ s or bystander’ s ar ea and

r esult in serious per sonal injur y or death.

– Do not change the engine speed

setting .

– If y ou suspect the engine speed

is f aster than nor mal, contact an

Authoriz ed Ser vice Dealer .

• Clean the air ﬁlter frequently . Mulc hing stirs

up more clippings and dust whic h clogs the air

ﬁlter and reduces engine perfor mance .

Cutting Grass

• Grass g ro ws at different rates at different

times of the year . In the summer heat, it is

best to cut g rass at the 2-1/4 inc h (57 mm),

2-3/4 inc h (70 mm), or 3-1/4 inc h (83 mm)

cutting height settings . Cut only about a third

of the g rass blade at a time . Do not cut belo w

the 2-1/4 inc h (57 mm) setting unless the g rass

is sparse or it is late fall when g rass g ro wth

begins to slo w do wn.

• W hen cutting g rass o v er 6 inc hes (15 cm) tall,

ﬁrst mo w at the highest cutting height setting

and w alk slo w er; then mo w ag ain at a lo w er

setting for the best la wn appearance . If the

g rass is too long and the lea v es clump on top

of the la wn, the mo w er ma y plug and cause the

engine to stall.

• Alter nate the mo wing direction. T his helps

disperse the clippings o v er the la wn for ev en

fer tilization.

If the ﬁnished la wn appearance is unsatisfactor y ,

tr y one or more of the follo wing:

• Shar pen the blade .

• W alk at a slo w er pace while mo wing .

• Raise the cutting height on y our mo w er .

• Cut the g rass more frequently .

• Ov erlap cutting sw aths instead of cutting a full

sw ath with eac h pass .

• Set the cutting height on the front wheels one

notc h lo w er than the rear wheels . F or example ,

set the front wheels at 2-1/4 inc hes (57 mm)

and the rear wheels at 2-3/4 inc hes (70 mm).

Cutting Leaves

• After cutting the la wn, ensure that half of the

la wn sho ws through the cut leaf co v er . Y ou

ma y need to mak e more than one pass o v er

the lea v es .

• F or light leaf co v erag e , set all the wheels at the

same cutting height setting .

• If there are more than 5 inc hes (12.7 cm) of

lea v es on the la wn, set the front cutting height

1 or 2 notc hes higher than the rear cutting

height. T his mak es it easier to feed the lea v es

under the mo w er housing .

• Slo w do wn y our mo wing speed if the mo w er

does not cut the lea v es ﬁnely enough.

• If y ou mo w o v er oak lea v es , y ou can add lime

to the g rass in the spring to reduce the acidity

of the oak lea v es .

Maintenance

Note: Deter mine the left and right sides of the mac hine from the nor mal operating position.

Recommended Maintenance Schedule(s)

Maintenance Service

Interval

Maintenance Procedure

After the rst 8 operating

hours

• Change the engine oil.

Before each use or daily

• Check the engine oil level.

• Inspect the mower blades for wear or damage.

• Clean under the mower housing.

Every 25 hours

• Clean the foam pre-cleaner (more frequently in dusty conditions).

Every 50 hours

• Lubricate the pivot arms.

• Change the engine oil (more often in dusty conditions).

• Check the fuel hose and replace it if necessary.

• Clean the blade brake clutch shield.

Every 100 hours

• Lubricate the gear case.

• Clean the air cooling ns.

• Change the oil lter.

• Check the spark plug.

• Clean the fuel lter.

Every 300 hours

• Replace the paper air lter (more frequently in dusty conditions).

Yearly or before storage

• Empty the fuel tank.

Important: R efer to y our Engine Operator’ s Man ual f or additional maintenance pr ocedur es.

If y ou lea v e the wir e on the spar k plug , someone could accidentl y star t the engine and

seriousl y injur e y ou or other bystander s.

Disconnect the wir e fr om the spar k plug bef or e y ou do an y maintenance. Set the wir e aside so

that it does not accidentl y contact the spar k plug .

Lubrication

Lubricating the Pivot Arms

After ev er y 50 operating hours or when the season

ends , lubricate the pi v ot ar ms .

1. Mo v e the rear wheel cutting height lev ers to

the center setting .

2. Wipe the g rease ﬁttings with a clean rag

( Figure 19 ).

Figure 19

3. Install a g rease gun onto the ﬁtting and g ently

apply 2 or 3 pumps of #2 m ulti-pur pose

lithium-base g rease .

Important: Ex cessi v e g r ease pr essur e

may dama ge the seals.

Lubricating the Gear Case

After ev er y 100 operating hours , g rease the g ear

case .

1. R emo v e the g rass bag .

2. Install a g rease gun onto the ﬁtting through the

belt co v er opening ( Figure 20 ).

Figure 20

3. Gently apply one to 2 pumps of #2

m ulti-pur pose lithium-base g rease .

4. Install the g rass bag .

Engine Maintenance

Servicing the Air Filter

Clean the foam pre-cleaner ev er y 25 operating

hours . R e place the paper air ﬁlter once ev er y

season or ev er y 300 operating hours; re place it

more frequently in dusty conditions .

Important: Do not operate the engine

without the air ﬁlter assembl y; extr eme engine

dama ge will occur .

1. Stop the engine and w ait for all mo ving par ts

to stop .

2. Disconnect the wire from the spark plug

( Figure 11 ).

3. R emo v e the co v er and clean it thoroughly

( Figure 21 ).

Figure 21

1. Cover

3. Air lter base

2. Paper air lter

4. R emo v e and inspect the paper air ﬁlter

( Figure 21 ), and discard it if it is ex cessi v ely

dir ty .

Important: Do not tr y to clean a paper

ﬁlter .

5. R emo v e the foam pre-cleaner and w ash it with

a mild deterg ent and w ater , then blot it dr y

( Figure 21 ).

6. Install the foam pre-cleaner onto the paper air

ﬁlter .

7. Install the air ﬁlter assembly .

Note: Install a new paper air ﬁlter if y ou

discarded the old one .

8. Install the co v er .

Changing the Engine Oil

Chang e the oil after the ﬁrst 8 operating hours and

than after ev er y 50 operating hours or ev er y season

(more frequently in dusty or dir ty conditions).

1. R un the engine to w ar m the engine oil.

Note: W ar m oil ﬂo ws better and car ries more

contaminants .

Oil may be hot after engine has been r un,

and contact with hot oil can cause sev er e

per sonal injur y .

A v oid contacting the hot engine oil when

y ou drain it.

2. Stop the engine and w ait for all mo ving par ts

to stop .

3. Disconnect the wire from the spark plug

( Figure 11 ).

4. Place a suitable drain pan under the right side

of the mo w er .

5. R emo v e the dipstic k b y rotating the cap

countercloc kwise and pulling it out.

6. Tip the mo w er onto its right side to drain the

oil into the drain pan.

Note: Y ou can also remo v e the oil from the

crankcase using an oil extractor .

7. R etur n the mo w er to its operating position.

8. Inser t the dipstic k into the ﬁller nec k and

rotate the cap cloc kwise until it is tight.

9. R ecycle the used oil according to local codes .

10. Fill the crankcase to the Full line on the

dipstic k with fresh oil. R efer to the Filling the

Crankcase with Oil.

11. Wipe up any spilled oil.

Changing the Oil Filter

R e place the oil ﬁlter ( Figure 22 ) after ev er y 100

operating hours or yearly , whic hev er comes ﬁrst.

Figure 22

1. Fuel valve 2. Oil lter

1. R un the engine to w ar m the oil.

Oil may be hot after the engine has been

r un, and contact with hot oil can cause

sev er e per sonal injur y .

A v oid contacting the hot engine oil when

y ou drain it.

2. Stop the engine and w ait for all mo ving par ts

to stop .

3. Disconnect the wire from the spark plug

( Figure 11 ).

4. Drain the engine oil; refer to Changing the

Engine Oil.

5. Place a rag under the oil ﬁlter to catc h any oil

that ma y leak out as y ou remo v e the ﬁlter .

6. R emo v e the oil ﬁlter .

7. Use y our ﬁng er to coat the g ask et on the new

ﬁlter with oil ( Figure 23 ).

Figure 23

1. Gasket

8. Install the new ﬁlter and hand tighten it 2/3

tur n only .

9. Fill the crankcase to the Full line on the

dipstic k with fresh oil. R efer to Filling the

Crankcase with Oil.

10. Connect the wire to the spark plug .

11. R un the engine for about 3 min utes .

12. Stop the engine , w ait for all mo ving par ts to

stop , and c hec k for oil leakag e around the ﬁlter .

13. Add oil to compensate for the oil in the oil

ﬁlter . R efer to Chec king the Engine Oil Lev el.

14. R ecycle the used oil ﬁlter according to local

codes .

Servicing the Spark Plug

Chec k the spark plug after ev er y 100 operating

hours . Use an NGK BPR5ES spark plug or

equi v alent.

1. Stop the engine and w ait for all mo ving par ts

to stop .

2. Disconnect the wire from the spark plug

( Figure 11 ).

3. Clean around the spark plug .

4. R emo v e the spark plug from the cylinder head.

Important: R eplace a crack ed, f ouled,

or dir ty spar k plug . Do not clean the

electr odes because g rit entering the

cylinder can dama ge the engine.

5. Set the g ap on the plug to 0.030 in. (0.76 mm)

( Figure 24 ).

Page is loading ...

Toro 21in Heavy-Duty Rear Bagger Lawn Mower User manual

Brand: Toro

Model: 21in Heavy-Duty Rear Bagger Lawn Mower

Category: Lawnmowers

Type: User manual

Download PDF

report

Toro 21in Heavy-Duty Rear Bagger Lawn Mower User manual

Toro 21in Heavy-Duty Rear Bagger Lawn Mower User manual

Related papers

Other documents