Legrand sfc_install_AtlasBracket (PDF) Installation guide

Legrand
Brand
Legrand
Model
sfc_install_AtlasBracket (PDF)
Type
Installation guide
Solarfective
®
Atlas Clamp System
Installation Instructions • Instructions d’Installation • Instrucciones de Instalación
No: 9000248 – 07/17 rev. 1
Country of Origin: Made in Canada • Pays d’origine: Fabriqué en Canada • País de origen: Hecho en Canadá
1. Place piece of masking tape with its top edge at the level of
the suspended ceiling, marking the bottom position of the
bracket. Use a level to ensure that the sides of the brackets
are level to each other.
2. Place piece of masking tape with its bottom edge 8-3/16”
above top of first piece of tape.
3. Peel off backer from double faced tape on pads. Attach pads
on each side of mullion, with top edges even with the bottom
edge of the upper tape mark. The pad tape should be at
the top.
4. Remove the upper masking tape.
OVERVIEW
The Atlas Clamp System is designed for installation of shades directly to vertical window mullions. The maximum weight shade for this
system is 25 pounds, and correct installation of this system is required for safety and product installation quality.
Required tools:
• Pencil
• Masking tape
• Torque wrench
• 12 point 9/32nd inch socket
• 7/16th inch socket
• Tape measure
NOTE: Prior to beginning, ensure that the torque wrench is set for 60 inch pounds of torque. This torque level is required to ensure that
the mullions are not damaged, as well as ensure that the shades stay in the proper position.
INSTALLATION
The Atlas Clamp System consists of a mullion clamp, attached to a hood that holds the end of the shade. Also included are two pads
placed between the bracket and the mullion, to protect the mullion.
CAUTION: Work gloves and protective eyewear should be worn during installation.
Level of suspended ceiling
8 3/16”
Bottom of tape
Top of pad
800.879.8585
www.legrand.us/wattstopper
No. 9000248 – 07/17 rev. 1
© Copyright 2017 Legrand All Rights Reserved.
© Copyright 2017 Tous droits réservés Legrand.
© Copyright 2017 Legrand Todos los derechos reservados.
Wattstopper warranties its products to be free
of defects in materials and workmanship for a
period of five (5) years. There are no obligations
or liabilities on the part of Wattstopper for
consequential damages arising out of, or in
connection with, the use or performance of this
product or other indirect damages with respect
to loss of property, revenue or profit, or cost of
removal, installation or reinstallation.
Wattstopper garantit que ses produits sont
exempts de défauts de matériaux et de fabrication
pour une période de cinq (5) ans. Wattstopper
ne peut être tenu responsable de tout dommage
consécutif causé par ou lié à l’utilisation ou
à la performance de ce produit ou tout autre
dommage indirect lié à la perte de propriété, de
revenus, ou de profits, ou aux coûts d’enlèvement,
d’installation ou de réinstallation.
Wattstopper garantiza que sus productos
están libres de defectos en materiales y mano
de obra por un período de cinco (5) años. No
existen obligaciones ni responsabilidades por
parte de Wattstopper por daños consecuentes
que se deriven o estén relacionados con el
uso o el rendimiento de este producto u otros
daños indirectos con respecto a la pérdida
de propiedad, renta o ganancias, o al costo
de extracción, instalación o reinstalación.
WARRANTY INFORMATION INFORMATIONS RELATIVES À LA GARANTIE INFORMACIÓN DE LA GARANTÍA
5. With the four square head screws and jam nuts loosened,
place the clamp on the mullion and center it between the
bottom and top of the pad. Then adjust it so that the bottom
of the hood is exactly at the top of the bottom piece of
masking tape. Hand tighten the four screws until they each
make contact with the pad. Turn each screw another ¼ turn.
This should keep the clamp from slipping before using the
torque wrench.
6. Using a torque wrench and a 12 point 9/32nd inch socket,
tighten each square head screw to 60 in-lb. Do one side first
and then the other. Double check to ensure proper torque on
each screw.
7. Using a torque wrench and a 7/16th inch socket, tighten
each jam nut to 60 in-lb.
8. Remove the bottom piece of masking tape.
9. Once the mullion clamps are installed, verify that the
brackets are level and level to each side. Use the level to
help in this process.
10. Once the Atlas brackets are installed for each side of the
shade, you may prepare to install your shade in the hood,
following the instructions for the shade as provided.
Bottom of hood
Top of tape
THE ATLAS BRACKET IS INTENDED ONLY
FOR MOUNTING PROPERLY SIZED SHADES.
CEILING CONTRACTORS AND OTHER
TRADES SHOULD NOT USE THE BRACKET OR
THE SHADE IT SUPPORTS AS A SUPPORT FOR
THEIR PRODUCTS. SUCH IMPROPER USE WILL
CAUSE SYSTEM FAILURES AND DAMAGE.
  • Page 1 1
  • Page 2 2

Legrand sfc_install_AtlasBracket (PDF) Installation guide

Legrand
Brand
Legrand
Model
sfc_install_AtlasBracket (PDF)
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents