Panasonic KXLD720 Important information

Brand: Panasonic

Model: KXLD720

Type: Important information

TechInfo Sheet fax: 01344 853394

Data Products email: [email protected]

Panasonic CS U.K. Document No: 1

Model: KXL-D720

Product Group: Model: KXL-D720

Date: 30 September 1999 Revision No: 1 Document No:

Subject: Windows 98 Installation

Confirmation of PCMCIA Controller

Operation

To ensure that the PCMCIA Controller in Windows 98 is running in 32-bit mode, please follow these instructions:-

DO NOT have the Interface Card inserted in the computer's card slot at this stage.

(1) Turn on your computer.

Windows 98 automatically starts.

(2) Click Start, point to "Settings" and then click "Control Panel".

(3) Double-click the PC Card (PCMCIA) icon.

Either (A) the "PC Card (PCMCIA) Wizard" or (B) the "PC Card (PCMCIA) Properties"

window will appear.

(A) If the "PC Card (PCMCIA) Wizard" window appears

===================================================

The PCMCIA controller is not running in 32-bit mode, therefore you will need to install the 32-bit driver.

Follow the steps below to install the 32-bit mode Windows driver.

(1) Select "No" and then click Next >.

(2) Select "No" and then click Next >.

(3) Click Finish.

The "System Settings Change" window appears.

(4) Click Yes to exit Windows 98.

The computer will be turned off.

(5) Turn on your computer, restart Windows 98.

B) If the "PC Card (PCMCIA) Properties" window appears

===================================================

The 32-bit mode Windows driver is already installed.

TechInfo Sheet fax: 01344 853394

Data Products email: [email protected]

Panasonic CS U.K. Document No: 1

Model: KXL-D720

(1) Click Cancel.

After you have confirmed that the PCMCIA controller is running in 32-bit mode, you must install the device drivers

for the CD-ROM Player in Windows 98.

There are two methods for installing the device driver as follows:-

We recommend that you follow "1. How to install the device driver before inserting the supplied Interface

Card ", especially when you wish to install the CD-ROM Player on following computers:-

(A) The computer has only one PC card slot that is connected to floppy disk drive.

(e.g. Toshiba Libretto series, Compaq CONTURA AERO series)

(B) A computer that has SystemSoft CardWorks card manager software installed.

(e.g. Toshiba DynaBook TECRA/Satellite/PORTEGE, Panasonic CF-41)

1. How to install the device driver before inserting the supplied Interface Card

===============================================================

Please make sure that the Interface Card is not inserted into the computer's card slot.

(1) Turn on your computer.

Windows 98 automatically starts.

(2) Double-click the Add New Hardware icon in the Control Panel.

The "Add New Hardware Wizard" window appears.

(3) Click Next >.

(4) Click Next >.

If the "Is the device that you want to install listed below?" message appears, select "No, the

device isn't in the list.", then click Next >.

(5) Select "No", then click Next >.

The hardware option pull-down menu appears.

(6) Select "SCSI controllers", then click Next >.

(7) Click Have Disk….

The "Install From Disk" window appears.

(8) Insert the supplied Setup disk into the computer's floppy disk drive, then click OK.

(9)

Make sure that the "Panasonic KXLC00#" is displayed in the Models dialog box, then click Next

# = Interface Card ID number. (1, 2, 3, 4, 5)

(10)Click Next >.

(11)Click Finish, and remove the Setup disk from the computer.

This completes the driver installation.

Please connect the CD-ROM Player and your computer, refer to the Operating Instructions.

TechInfo Sheet fax: 01344 853394

Data Products email: [email protected]

Panasonic CS U.K. Document No: 1

Model: KXL-D720

2. How to install the device driver after inserting the supplied Interface Card

==========================================================

Make sure that the Interface Cable is connected to the Interface Card and to the CD-ROM Player.

(1) Turn on your computer.

Windows 98 automatically starts.

(2) Turn on the CD-ROM Player. (Except KXL-8XXA series)

(3) Insert the Interface Card into the computer's card slot firmly.

The "Add New Hardware Wizard" window appears.

(4) Click Next >.

(5) Select "Search for the best driver for your device", then click Next >.

(6)

Insert the supplied Setup disk into the computer's floppy disk drive, and select "Floppy disk

drives", then click Next >.

(7) Click Next >.

(8) Click Finish, and remove the Setup disk from the computer.

This completes the driver installation.

Panasonic KXLD720 Important information

Panasonic KXLD720 Important information

Panasonic KXLD720 Important information

Related papers

Other documents