Zanussi ZRB229MWO User manual

Category
Fridges
Type
User manual

This manual is also suitable for

Replacing the light bulb
Disconnect the appliance from the mains supply.
Remove the screw to release the lamp cover , the
lamp bulb is located in the lamp holder ,
unscrew the lamp in an anti-clockwise direction
until the lamp comes out of the lamp holder.
Screw a new lamp bulb (15 Watt & E14 Base)
into the lamp holder in a
clockwise direction until tight.
Replace the lamp cover and
screw back into place.
Reconnect the appliance to
The mains supply.
Replacing the light bulb
Defrosting
The freezer compartment , however , will become
progressively covered with frost. This should be
removed with the special plastic scraper provided ,
whenever the thickness of the frost exceeds 4mm.
During this operation it is not necessary to switch
off the power supply or to remove the foodstuffs.
However , when the ice becomes very thick
Defrosting
on the inner liner , complete defrosting should be
carried out as follows:
1. Pull out the plug from the wall socket ;
2. Remove any stored food , wrap it in several layers
and put it in a cool place;
3. Open the door and clean the appliance according
to 'Periodic cleaning';
Maintain and clean the freezer as following:
Sweep off the melting water with a dry cloth on each
layer of evaporator , The melting water swept down
gathers in the outlet channel which is situated in the
bottom of the appliance and can be removed
according to diagram below:
Put an adequately high bowl or dish under the
outlet.
4. When defrosting is completed , dry the interior
thoroughly; keep the scraper for future use;
5. Replace the plug in the power socket;
6. After two or three hours , reload the previously
removed food into the compartment.
Important !
Never use sharp metal tools to scrape off frost
from the evaporator as you could damage it.
Do not use a mechanical device or any artificial
means to speed up the thawing process other
than those recommended by the manufacturer.
A rise in the temperature of the frozen food during
defrosting , may shorten their safe storage life.
Important !
1
2
1.Door Stop
2.Door Stop Screw
3. Unscrew the bolts which are used to fix the
bottom hinge with the narrow head of a spanner ,
and unscrew the bottom hinge with screwdriver ,
then remove the door carefully; After that use the
middle hole of the spanner to unscrew the hinge
pin and stopper , unscrew the nut which is used
to fix the hinge pin with the wide head of a
spanner and place them in the symmetrical holes.
Fix the stopper in the middle of the
condenser , rotate the stopper 90 degrees and fixed
the position.
6. Rotate the pin by using the wide-head of the
spanner and remove the left hole cover with a
screwdriver , exchange the assembly location and fix it
as the previous method.
7. Change the handle. (which is the same method for
both fridge door and freezer door)
Remove two side of plastic hole cover and
handle with a screwdriver , fix them on the opposite
side. Put the plastic hole covers over were the handle
was originally situated.
8. Install the door carefully , adjust assembly position ,
move the hinge to left symmetrical position , then fix it
with the bolt. then use bolt to fix , install adjustable
foot to an appropriate location.
1. Tilt the refrigerator back to set at an angle.
2. Rotate the left and right adjustable front feet at
the bottom by hand , turning them anti-clockwise.
4. Remove the stopper which is under the bottom
door trim with a screwdriver , then install it to the left
symmetrical.
5. Rotate the bolt which is used to fix the middle
hinge with screwdriver , remove the middle hinge , then
carefully remove fridge door.
ยท
1 / 1

Zanussi ZRB229MWO User manual

Category
Fridges
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Ask the document