Krone Messages - Parameters Operating instructions
- Type
- Operating instructions
Enclose this document with the operating instructions of the
machine.
Supplement to operating
instructions
Document number: 150001622_03_us
Version: 22/09/2023
Round baler
Software version: D2515020105300036
Error messages
Table of contents
2
Round baler
Supplement to operating instructions 150001622_03_en
1 Information on this document ..................................................................................................3
1.1 Validity .........................................................................................................................................3
1.2 Re-ordering ..................................................................................................................................3
1.3 Applicable documents..................................................................................................................3
2 Safety ..........................................................................................................................................4
2.1 Meaning of the supplement to the operating instructions ............................................................4
3 Error Messages ..........................................................................................................................5
3.1 Possible error types (FMI)............................................................................................................6
3.2 Error list........................................................................................................................................6
4 Index..........................................................................................................................................30
Information on this document 1
Validity 1.1
Round baler
Supplement to operating instructions 150001622_03_en 3
1 Information on this document
1.1 Validity
This document is valid for:
RP301-21 (VariPack V 190 XC Plus) RP301-11 (VariPack V 165 XC Plus)
RP301-20 (VariPack V 190 Plus) RP301-10 (VariPack V 165 Plus)
RP201-21 (VariPack V 190 XC) RP201-20 (VariPack V 190)
RP201-11 (VariPack V 165 XC) RP201-10 (VariPack V 165)
RP701-51 (Comprima V 210 XC) RP701-40 (Comprima V 180)
RP701-30 (Comprima V 150) RP601-41 (Fortima V 1800 MC)
RP601-40 (Fortima V 1800) RP601-30 (Fortima V 1500)
RP801-31 (Comprima V 150 XC Plus) RP701-41 (Comprima V 180 XC)
RP701-31 (Comprima V 150 XC) RP701-21 (Comprima F 155 XC)
RP701-20 (Comprima F 155) RP701-11 (Comprima F 125 XC)
RP601-31 (Fortima V 1500 MC) RP601-21 (Fortima F 1600 MC)
RP601-20 (Fortima F 1600) RP601-11 (Fortima F 1250 MC)
RP601-10 (Fortima F 1250) RP701-10 (Comprima F 125)
RP801-21 (Comprima F 155 XC Plus)
1.2 Re-ordering
If this document has become completely or partially unusable or if another language is required,
you can request a replacement document by quoting the document number indicated on the
cover sheet. Furthermore, the document can also be downloaded online via
KRONEMEDIAhttps://media.mykrone.green or via the TIChttps://mykrone.green/control/
subsystemauth?system=S017.
1.3 Applicable documents
To ensure that the machine is used safely and as intended, observe the following further
applicable documents.
• Operating instructions of the respective machine
2 Safety
2.1 Meaning of the supplement to the operating instructions
4
Round baler
Supplement to operating instructions 150001622_03_en
2 Safety
WARNING
Risk of injury due to non-observance of relevant safety instructions
If the relevant safety instructions are not observed, persons may be seriously injured or killed.
In order to avoid accidents, the relevant safety instructions in the operating instructions
must be read and observed.
WARNING
Risk of injury due to non-observance of safety routines
If the relevant safety routines are not observed, persons may be seriously injured or killed.
In order to avoid accidents, the safety routines in the operating instructions must be read
and observed.
INFO
Depending on the machine type, the basic safety instructions can be found in the chapter
“Safety”, “Basic Safety Instructions” or in the chapter “Safety” of the machine operating
instructions.
2.1 Meaning of the supplement to the operating instructions
The supplement to the operating instructions is an important document and a part of the
machine. It is aimed at the user and contains safety-relevant information.
If the supplement to the operating instructions is not observed, people may be seriously injured
or killed.
Read in full and observe the “Safety” chapter of the corresponding operating instructions
before using the machine for the first time,see Page3.
Before working, also read and observe the respective sections of the corresponding
operating instructions,see Page3.
Keep the supplement to the operating instructions ready to hand for the user of the machine.
Hand over the supplement to the operating instructions to subsequent users.
Error Messages 3
Round baler
Supplement to operating instructions 150001622_03_en 5
3 Error Messages
WARNING
Risk of injury to persons and damage to machines if error messages are ignored
If error messages are ignored and the fault is not rectified, there is a risk of injury to persons
and/or severe damage to the machine.
Eliminate the disturbance when an error message is displayed, see Page6.
If the fault cannot be rectified, contact KRONE service partner.
KMC - 521202- 5
B11 L
EQG000-034
The display shows an error message when a disturbance occurs on the machine. At the same
time, an audible signal sounds (continuous horn signal). For a list of the error messages, see
Page6.
Configuration of an error message
The error message is configured according to the following sample: e.g. error message
"520192-19
CAN1
"
520192 19
CAN1
SPN (Suspect Parameter
Number) = error number
FMI = type of error, see
Page6
Icon
Acknowledging error message
Note down the error message.
Briefly press on .
ÆThe acoustic signal stops and the error display is no longer indicated. The error message is
displayed again if the fault occurs again.
To acknowledge the error message until the operating terminal is next started, press and
hold down the key for 5seconds.
Rectify the error, see Page6.
3 Error Messages
3.1 Possible error types (FMI)
6
Round baler
Supplement to operating instructions 150001622_03_en
Acknowledged and still pending error messages can be displayed again via the "Error list" menu
or the status line.
3.1 Possible error types (FMI)
There are different types of errors which are shown under the term FMI (Failure Mode
Identification) with an appropriate code.
FMI Meaning
0 The upper limit value was greatly exceeded.
1 The lower limit value was far below the required one.
2 The data is not permitted.
3 There is an overvoltage or a short circuit to supply voltage.
4 There is an undervoltage or a short circuit to ground.
5 A cable is broken or amperage is too low.
6 There is a short circuit to ground or amperage is too low.
7 The mechanics do not respond or the expected result was not achieved.
8 The frequency is not permitted.
9 There is an abnormal update rate.
10 There is an abnormal rate of change.
11 The error cause is unknown.
12 There is an internal error.
13 The values of the calibration are outside the value range.
14 Particular instructions are required.
15 The upper limit value has been reached.
16 The upper limit value has been exceeded.
17 The lower limit value has been reached.
18 The lower limit value has not been reached.
19 There is a CAN communication failure.
20 The data deviates upwards.
21 The data deviates downwards.
31 The condition has been fulfilled.
3.2 Error list
Overview of the control units
Abbreviation Explanation
KMC KRONE Machine Controller
>>>
2D2515020105300036 [}7]
Error list
Software version: D2515020117900036_100,
D2515020105400036_100
Control unit: KMC
Page 1
Error number Error text Description Figure
KMC-520192-19 CAN 1 - CAN disturbance between
control units
There is a CAN disturbance between
control units on CAN 1.
KMC-520193-19 CAN 2 - CAN disturbance between
control units
There is a CAN disturbance between
control units on CAN 2.
KMC-520194-19 CAN 3 - CAN disturbance between
control units
There is a CAN disturbance between
control units on CAN 3.
KMC-520195-19 CAN 4 - CAN disturbance between
control units
There is a CAN disturbance between
control units on CAN 4.
KMC-520198-12 Control unit - Internal Error An internal error in the control unit
which was actuated by defective
software or hardware.
KMC-520232-12 Vehicle identification number -
Internal Error
Vehicle identification number has not
been initialised.
KMC-520234-31 System check with KMC failed With the KMC the cross-controller
adjustment of system-relevant
machine data has failed.
KMC-521100-3 Voltage group UB1 - Overvoltage The input voltage of the corresponding
voltage group is too high.
KMC-521100-4 Voltage group UB1 - Undervoltage The input voltage of the corresponding
voltage group is too low.
KMC-521100-5 Voltage group UB1 - Ground fault A ground fault has occurred on the
supply voltage.
KMC-521100-6 Voltage group UB1 - Overload The maximum load on the supply
voltage has been exceeded.
KMC-521101-3 Voltage group UB2 - Overvoltage The input voltage of the corresponding
voltage group is too high.
KMC-521101-4 Voltage group UB2 - Undervoltage The input voltage of the corresponding
voltage group is too low.
KMC-521101-5 Voltage group UB2 - Ground fault The maximum load on the supply
voltage has been exceeded.
KMC-521101-6 Voltage group UB2 - Overload The maximum load on the supply
voltage has been exceeded.
KMC-521102-3 Voltage group UB3 - Overvoltage The input voltage of the corresponding
voltage group is too high.
Page 2
Error number Error text Description Figure
KMC-521102-4 Voltage group UB3 - Undervoltage The input voltage of the corresponding
voltage group is too low.
KMC-521102-5 Voltage group UB3 - Ground fault A ground fault has occurred on the
supply voltage.
KMC-521102-6 Voltage group UB3 - Overload The maximum load on the supply
voltage has been exceeded.
KMC-521103-3 Voltage group UB4 - Overvoltage The input voltage of the corresponding
voltage group is too high.
KMC-521103-4 Voltage group UB4 - Undervoltage The input voltage of the corresponding
voltage group is too low.
KMC-521103-5 Voltage group UB4 - Ground fault A ground fault has occurred on the
supply voltage.
KMC-521103-6 Voltage group UB4 - Overload The maximum load on the supply
voltage has been exceeded.
KMC-521104-3 Voltage group UB5 - Overvoltage The input voltage of the corresponding
voltage group is too high.
KMC-521104-4 Voltage group UB5 - Undervoltage The input voltage of the corresponding
voltage group is too low.
KMC-521104-5 Voltage group UB5 - Ground fault A ground fault has occurred on the
supply voltage.
KMC-521104-6 Voltage group UB5 - Overload The maximum load on the supply
voltage has been exceeded.
KMC-521105-3 Voltage group UB6 - Overvoltage The input voltage of the corresponding
voltage group is too high.
KMC-521105-4 Voltage group UB6 - Undervoltage The input voltage of the corresponding
voltage group is too low.
KMC-521105-5 Voltage group UB6 - Ground fault A ground fault has occurred on the
supply voltage.
KMC-521105-6 Voltage group UB6 - Overload The maximum load on the supply
voltage has been exceeded.
KMC-521106-11 Supply voltage sensors - General
disturbance
The voltage has been switched off due
to an overload or a short circuit on the
supply voltage of the sensors.
Page 3
Error number Error text Description Figure
KMC-521107-3 Supply voltage - Overvoltage The power supply on the UE
connection is too high.
KMC-521107-4 Supply voltage - Undervoltage The power supply on the UE
connection is too low.
KMC-521108-11 Control unit - General disturbance The voltage group relay UB1 has not
passed the self-test.
KMC-521109-11 Control unit - General disturbance The voltage group relay UB2 has not
passed the self-test.
KMC-521110-11 Control unit - General disturbance The voltage group relay UB3 has not
passed the self-test.
KMC-521111-11 Control unit - General disturbance The voltage group relay UB4 has not
passed the self-test.
KMC-521112-11 Control unit - General disturbance The voltage group relay UB5 has not
passed the self-test.
KMC-521113-11 Control unit - General disturbance The voltage group relay UB6 has not
passed the self-test.
KMC-521114-11 Sensor supply voltage U1 - General
disturbance
The voltage group Uext1 for supplying
the sensors is defective, for example
due to overload or short circuit.
KMC-521115-11 Sensor supply voltage U2 - General
disturbance
The voltage group Uext2 for supplying
the sensors is defective, for example
due to overload or short circuit.
KMC-521116-11 Sensor supply voltage U3 - General
disturbance
The voltage group Uext3 for supplying
the sensors is defective, for example
due to overload or short circuit.
KMC-521117-11 Sensor supply voltage U4 - General
disturbance
The voltage group Uext4 for supplying
the sensors is defective, for example
due to overload or short circuit.
KMC-521118-11 Voltage group relay UB2 - General
disturbance
Platform fault for BiG X only: A
disturbance was detected at the
intake/header (broken cable/short
circuit to one of the valves Q55 - Q58
or a broken cable/short circuit from
relay Q72). The voltage group relay
UB2 was therefore switched off.
KMC-521320-2 Machine configuration - Logic error
electronics
Configuration of the machine is not
compatible with the hardware.
KMC-521350-11 Control unit - General disturbance
Page 4
Error number Error text Description Figure
KMC-521351-11 Control unit - General disturbance
KMC-522000-7 Quick-stop switch - Logic fault
mechanics
The quick-stop switch has been
activated.
KMC-522001-7 Quick-stop retaining bracket - Logic
fault mechanics
The quick-stop retaining bracket has
been activated.
KMC-522005-2 Universal shaft - Logic error
electronics
The universal shaft rotates and the
operating status is road mode.
KMC-522005-16 Universal shaft - Upper limit value
exceeded
The universal shaft is rotating faster
than permitted.
KMC-522010-7 Blade cassette movement prompt -
Logic fault mechanics
The blade cassette must be lifted.
KMC-522011-7 Blade cassette movement prompt -
Logic fault mechanics
The blade cassette must be lowered.
KMC-522012-7 Blade cassette not up - Logic fault
mechanics
The blade cassette is not up.
KMC-522014-7 Blade cassette movement prompt -
Logic fault mechanics
The blade cassette must be
pressurised.
KMC-522015-7 Blade cassette Timeout - Logic fault
mechanics
Movement of the blade cassette has a
timeout.
KMC-522017-7 Logic fault mechanics
KMC-522018-7 Logic fault mechanics
KMC-522019-7 Logic fault mechanics
KMC-522020-7 Tying net not pulled - Logic fault
mechanics
The wrapping and tying material was
not received by/pulled from the bale
when tying is activated.
KMC-522021-7 Tying net stopped - Logic fault
mechanics
The wrapping and tying material stops
after a certain time when tying is
activated.
KMC-522022-7 Tying net is being pulled - Logic fault
mechanics
The wrapping and tying material is
being pulled from the bale even though
tying has not started.
Page 5
Error number Error text Description Figure
KMC-522023-18 Feed roller below minimum speed -
Lower limit value below minimum
The feed roller is below the minimum
speed when the wrapping and tying
material is pulled.
KMC-522024-7 Tying net not cut off - Logic fault
mechanics
The wrapping and tying material has
not been cut off.
KMC-522025-7 Tying net not pulled - Logic fault
mechanics
The wrapping and tying material was
not received by/pulled from the bale
when tying is activated.
KMC-522026-7 Tying net stopped - Logic fault
mechanics
The wrapping and tying material stops
after a certain time when tying is
activated.
KMC-522027-7 Tying net is being pulled - Logic fault
mechanics
The wrapping and tying material is
being pulled from the bale even though
tying has not started.
KMC-522028-7 Tying net not cut off - Logic fault
mechanics
The wrapping and tying material has
not been cut off.
KMC-522029-7 Tying twine not pulled - Logic fault
mechanics
The wrapping and tying material was
not received by/pulled from the bale
when tying is activated.
KMC-522030-7 Tying twine stopped - Logic fault
mechanics
The wrapping and tying material stops
after a certain time when tying is
activated.
KMC-522031-7 Tying twine is being pulled - Logic
fault mechanics
The wrapping and tying material is
being pulled from the bale even though
tying has not started.
KMC-522032-18 Feed roller below minimum speed -
Lower limit value below minimum
The feed roller is below the minimum
speed when the wrapping and tying
material is pulled.
KMC-522033-7 Tying twine not cut off - Logic fault
mechanics
The wrapping and tying material has
not been cut off.
KMC-522034-7 Tying twine Timeout - Logic fault
mechanics
The twine arms could not be moved
within the stipulated time into the
required position.
KMC-522035-16 Maximum filling exceeded - Upper
limit value exceeded
The bale chamber has been filled
above the maximum.
KMC-522038-18 Slip of bale formation conveyor -
Lower limit value below minimum
The setpoint speed of the bale
formation conveyor of the bale
chamber was below the minimum.
KMC-522040-16 Left bale conical - Upper limit value
exceeded
The filling between the left and right
sides of the bale differs too much, too
large on the left.
KMC-522041-16 Right bale conical - Upper limit value
exceeded
The filling between the left and right
sides of the bale differs too much, too
large on the right.
Page 6
Error number Error text Description Figure
KMC-522044-7 Position of tailgate unclear - Logic
fault mechanics
The position of the tailgate could not
be determined.
KMC-522045-7 Open tailgate Timeout - Logic fault
mechanics
The tailgate could not be opened within
the stipulated time.
KMC-522046-7 Close tailgate Timeout - Logic fault
mechanics
The tailgate could not be closed within
the stipulated time.
KMC-522048-7 Tailgate open - Logic fault mechanics The tailgate is open during road
operating mode.
KMC-522049-7 Tailgate open - Logic fault mechanics An open tailgate was detected,
although no tying has occurred since it
was last closed.
KMC-522050-18 Rotational speed universal shaft -
Lower limit value below minimum
The PTO speed is too low.
KMC-522051-7 Position of tailgate - Logic fault
mechanics
The position of the tailgate is not
correct.
KMC-522052-7 Position of lifter - Logic fault
mechanics
The position of the lifter is not correct.
KMC-522053-7 Position of wrapping table - Logic
fault mechanics
The position of the wrapping table is
not correct.
KMC-522054-7 Position wrapping arm - Logic fault
mechanics
The position of the wrapping arm is not
correct.
KMC-522055-7 Position of holding arms - Logic fault
mechanics
The position of the holding arm is not
correct.
KMC-522056-7 Transfer Timeout - Logic fault
mechanics
The transfer has a timeout.
KMC-522057-7 Bale on lifter - Logic fault mechanics
KMC-522058-7 Bale on wrapping table - Logic fault
mechanics
There is a bale on the wrapping table.
KMC-522060-7 Tailgate automatic system Timeout -
Logic fault mechanics
The tailgate automatic system has a
Timeout
KMC-522061-7 Logic fault mechanics
Page 7
Error number Error text Description Figure
KMC-522066-7 Lifter Timeout - Logic fault mechanics The lifter of the bale transfer could not
be moved within the stipulated time
into the required position.
KMC-522070-7 Wrapping table Timeout - Logic fault
mechanics
The wrapping table could not be moved
within the stipulated time into the
required position.
KMC-522075-7 Film tear on one side - Logic fault
mechanics
The film is torn on one side.
KMC-522076-7 Film tear on both sides - Logic fault
mechanics
The film is torn on both sides.
KMC-522078-16 Moisture measurement - Upper limit
value exceeded
The upper moisture limit value was
below the minimum during the
moisture measurement.
KMC-522079-18 Moisture measurement - Lower limit
value below minimum
The lower moisture limit value was
below the minimum during the
moisture measurement.
KMC-522080-7 Tying film not pulled - Logic fault
mechanics
The wrapping and tying material was
not received by/pulled from the bale
when tying is activated.
KMC-522081-7 Tying film stopped - Logic fault
mechanics
The wrapping and tying material stops
after a certain time when tying is
activated.
KMC-522082-7 Tying film is being pulled - Logic fault
mechanics
The wrapping and tying material is
being pulled from the bale even though
tying has not started.
KMC-522083-7 Tying film not cut off - Logic fault
mechanics
The wrapping and tying material has
not been cut off.
KMC-522084-7 Tying twine not pulled - Logic fault
mechanics
The wrapping and tying material was
not received by/pulled from the bale
when tying is activated.
KMC-522085-7 Tying twine stopped - Logic fault
mechanics
The wrapping and tying material stops
after a certain time when tying is
activated.
KMC-522086-7 Tying twine is being pulled - Logic
fault mechanics
The wrapping and tying material is
being pulled from the bale even though
tying has not started.
KMC-522087-7 Tying twine not cut off - Logic fault
mechanics
The wrapping and tying material has
not been cut off.
KMC-522088-7 Tying net Timeout movement - Logic
fault mechanics
The rocker arm could not be moved to
the required position within the
specified time
KMC-522089-7 Tying film Timeout movement - Logic
fault mechanics
The rocker arm could not be moved to
the required position within the
specified time.
Page 8
Error number Error text Description Figure
KMC-522091-18 Baling pressure below minimum -
Lower limit value below minimum
The baling pressure is below the
minimum required value
KMC-522093-7 Position of tailgate Combi unclear -
Logic fault mechanics
The position of the tailgate could not
be determined.
KMC-522094-7 Open tailgate Combi Timeout - Logic
fault mechanics
The tailgate could not be opened within
the stipulated time.
KMC-522095-7 Close tailgate Combi Timeout - Logic
fault mechanics
The tailgate could not be closed within
the stipulated time.
KMC-522097-7 Tailgate Combi open - Logic fault
mechanics
The tailgate is open during road
operating mode.
KMC-522098-7 Tailgate Combi open - Logic fault
mechanics
An open tailgate was detected,
although no tying has occurred since it
was last closed.
KMC-522100-7 Bale on lifter - Logic fault mechanics
KMC-522101-3 Sensor B01 Speed of bale chamber -
Cable break
KMC-522101-4 Sensor B01 Speed of bale chamber -
Short circuit to ground or UB
KMC-522102-3 Sensor B02 Tying process active -
Cable break
KMC-522102-4 Sensor B02 Tying process active -
Short circuit to ground or UB
KMC-522103-3 Sensor B74 Acceleration wrapping
table - Cable break
KMC-522103-4 Sensor B74 Acceleration wrapping
table - Short circuit to ground or UB
KMC-522105-3 Sensor B05 Slip of bale formation
conveyor - Cable break
KMC-522105-4 Sensor B05 Slip of bale formation
conveyor - Short circuit to ground or
UB
KMC-522106-3 Sensor B06 Tying process active 1
twine tying - Cable break
Page 9
Error number Error text Description Figure
KMC-522106-4 Sensor B06 Tying process active 1
twine tying - Short circuit to ground
or UB
KMC-522107-3 Sensor B07 Tying process active 2
twine tying - Cable break
KMC-522107-4 Sensor B07 Tying process active 2
twine tying - Short circuit to ground
or UB
KMC-522108-3 Sensor B08 Blade cassette up -
Cable break
KMC-522108-4 Sensor B08 Blade cassette up -
Short circuit to ground or UB
KMC-522109-3 Sensor B09 Filling display on left -
Short circuit to UB
KMC-522109-4 Sensor B09 Filling display on left -
Cable break or short circuit to ground
KMC-522110-3 Sensor B10 Filling display on right -
Short circuit to UB
KMC-522110-4 Sensor B10 Filling display on right -
Cable break or short circuit to ground
KMC-522111-3 Sensor B11 Lock hook bale chamber
on left - Cable break
KMC-522111-4 Sensor B11 Lock hook bale chamber
on left - Short circuit to ground or UB
KMC-522112-3 Sensor B12 Lock hook bale chamber
on right - Cable break
KMC-522112-4 Sensor B12 Lock hook bale chamber
on right - Short circuit to ground or
UB
KMC-522113-3 Sensor B13 Position of twine guide
slide - Cable break
KMC-522113-4 Sensor B13 Position of twine guide
slide - Short circuit to ground or UB
KMC-522114-3 Sensor B14 Bale chamber open -
Cable break
Page 10
Error number Error text Description Figure
KMC-522114-4 Sensor B14 Bale chamber open -
Short circuit to ground or UB
KMC-522115-3 Sensor B15 ejecting the bale - Cable
break
KMC-522115-4 Sensor B15 ejecting the bale - Short
circuit to ground or UB
KMC-522120-3 Sensor B20 Zero position wrapping
arm - Cable break
KMC-522120-4 Sensor B20 Zero position wrapping
arm - Short circuit to ground or UB
KMC-522121-3 Sensor B21 Position wrapping arm -
Cable break
KMC-522121-4 Sensor B21 Position wrapping arm -
Short circuit to ground or UB
KMC-522122-3 Sensor B22 Left holding arm open -
Cable break
KMC-522122-4 Sensor B22 Left holding arm open -
Short circuit to ground or UB
KMC-522123-3 Sensor B23 Right holding arm open -
Cable break
KMC-522123-4 Sensor B23 Right holding arm open -
Short circuit to ground or UB
KMC-522124-3 Sensor B24 Film tear detection -
Cable break
KMC-522124-4 Sensor B24 Film tear detection -
Short circuit to ground or UB
KMC-522126-3 Sensor B26 Bale lifter down - Cable
break
KMC-522126-4 Sensor B26 Bale lifter down - Short
circuit to ground or UB
KMC-522127-3 Sensor B27 Position of wrapping
table - Short circuit to UB
Page 11
Error number Error text Description Figure
KMC-522127-4 Sensor B27 Position of wrapping
table - Cable break or short circuit to
ground
KMC-522135-3 Sensor B35 Left holding arm closed -
Cable break
KMC-522135-4 Sensor B35 Left holding arm closed -
Short circuit to ground or UB
KMC-522136-3 Sensor B36 Right holding arm closed
- Cable break
KMC-522136-4 Sensor B36 Right holding arm closed
- Short circuit to ground or UB
KMC-522140-3 Sensor B40 Blade group B swivelled
out - Cable break
KMC-522140-4 Sensor B40 Blade group B swivelled
out - Short circuit to ground or UB
KMC-522141-3 Sensor B41 Blade group B swivelled
in - Cable break
KMC-522141-4 Sensor B41 Blade group B swivelled
in - Short circuit to ground or UB
KMC-522142-3 Sensor B42 Blade group A swivelled
out - Cable break
KMC-522142-4 Sensor B42 Blade group A swivelled
out - Short circuit to ground or UB
KMC-522143-3 Sensor B43 Blade group A swivelled
in - Cable break
KMC-522143-4 Sensor B43 Blade group A swivelled
in - Short circuit to ground or UB
KMC-522146-3 Sensor B46 Blade control shaft 0 -
Cable break
KMC-522146-4 Sensor B46 Blade control shaft 0 -
Short circuit to ground or UB
KMC-522147-3 Sensor B47 Blade control shaft 1 -
Cable break
Page 12
Error number Error text Description Figure
KMC-522147-4 Sensor B47 Blade control shaft 1 -
Short circuit to ground or UB
KMC-522150-3 Sensor B50 Bale detection wrapping
table - Short circuit to UB
KMC-522150-4 Sensor B50 Bale detection wrapping
table - Cable break or short circuit to
ground
KMC-522151-3 Sensor B09 Filling display on left -
Short circuit to UB
KMC-522151-4 Sensor B09 Filling display on left -
Cable break or short circuit to ground
KMC-522152-3 Sensor B10 Filling display on right -
Short circuit to UB
KMC-522152-4 Sensor B10 Filling display on right -
Cable break or short circuit to ground
KMC-522161-3 Sensor B61 Tying 1 (passive) - Short
circuit to UB
KMC-522161-4 Sensor B61 Tying 1 (passive) - Cable
break or short circuit to ground
KMC-522162-3 Sensor B62 Tying 2 (active) - Cable
break
KMC-522162-4 Sensor B62 Tying 2 (active) - Short
circuit to ground or UB
KMC-522163-3 Sensor B63 Tying 3 (active) (twine) -
Short circuit to UB
KMC-522163-4 Sensor B63 Tying 3 (active) (twine) -
Cable break or short circuit to ground
KMC-522167-3 Sensor B67 Blade pre-selection
active - Cable break
KMC-522167-4 Sensor B67 Blade pre-selection
active - Short circuit to ground or UB
KMC-522168-3 Sensor B68 Blade pre-selection
inactive - Cable break
Page 13
Error number Error text Description Figure
KMC-522168-4 Sensor B68 Blade pre-selection
inactive - Short circuit to ground or
UB
KMC-522169-3 Sensor B69 blade active - Cable
break
KMC-522169-4 Sensor B69 blade active - Short
circuit to ground or UB
KMC-522177-3 Sensor B77 Bale lifter position -
Short circuit to UB
KMC-522177-4 Sensor B77 Bale lifter position -
Cable break or short circuit to ground
KMC-522182-3 Sensor B82 direction display - Short
circuit to UB
KMC-522182-4 Sensor B82 direction display - Cable
break or short circuit to ground
KMC-522183-3 Sensor B83 Overload protection belt
- Cable break
KMC-522183-4 Sensor B83 Overload protection belt
- Short circuit to ground or UB
KMC-522184-3 Sensor B84 baling pressure - Short
circuit to UB
KMC-522184-4 Sensor B84 baling pressure - Cable
break or short circuit to ground
KMC-522195-3 Position tensioning arm right Sensor
B95 Position tensioning arm right -
Short circuit to UB
KMC-522195-4 Position tensioning arm right Sensor
B95 Position tensioning arm right -
Cable break or short circuit to ground
KMC-522202-3 Sensor B02 Tying process active -
Cable break
KMC-522202-4 Sensor B02 Tying process active -
Short circuit to ground or UB
KMC-522206-3 Sensor B06 Tying process active 1
twine tying - Cable break
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
Krone Messages - Parameters Operating instructions
- Type
- Operating instructions
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Krone Messages - Parameters Operating instructions
-
Krone EzBA Meldungen – Parameter Operating instructions
-
Krone BA VariPack V 190 XC (RP201-21) Operating instructions
-
-
-
-
-
-
-
Krone BA BiG Pack 890 XC Operating instructions