urban ambiance UFS2011 Installation guide

Brand
urban ambiance
Model
UFS2011
Type
Installation guide
WarningsandCautions
1of2
Turn off electricity at circuitbreaker or mainfuseboxbeforeinstallation.Consult a licensedelectrician if in doubt.
Theseinstructionsareprovidedforyoursafety. It is veryimportantyoureadthemcompletelybeforeinstallingthefixture.Westrongly
recommendthatalicensed,professionalelectricianperformtheinstallation.
Disconnectfixturefrompowersourcebeforereplacingbulbs.Makesurebulbsaregivensufficienttime to coolbeforeremoval.
HardwareContents
AA
BB
Crossbar (x1)
Lock Washer
(x2)
Ceiling Canopy (x1)
EE
FF
QuickLink (x2)
Top Nut (x4)
E
PackageContents
A
B
Fixture Body
with Handle (x1)
18” rods (x2) D6” inchs for
flush mount
fixing (x2)
STEP1-AssembleFixture
Body and Fixture Handle
together
A.
B.
C.
D.
Open the bolt and top nut (A) from the fixture body.
Pull the handle up 90 degrees over the fixture body.
Pass the bolt from the fixture handle through the clips in the
fixture body.
Tighten the bolts on the fixture handle with the top nuts.
Figure 1
STEP 3 - Canopy Installation
A.
B.
Installation Instructions:
www.urbanambiance.com
Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire strippers, electrical tape, safety glasses
Bulb Recommended: Candelabra Base 60W Maximum
Estimated Assembly Time: 30-40 minutes
Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagram below to be sure all parts
are present. If any parts are missing or damaged, do not assemble, install or operate the fixture. Contact customer service for replacement
parts.
STEP 2 - Assemble Fixture Body and Rods
Pull the slack wire (black and
white) and ground wire through the
rods (B).
Thread the rods (B) over the fixture
handle.
Pull the slack wire (black and
white) and ground wire through the
rods (C).
Thread the rods (C) into rods (B).
Wrap exposed wires with sleeve
(HH)
Use the Quick link (D) to attach
over rod (C).
Attach the Quick Link (EE)
through the loop in the
rod (C).
Braid wire with sleeve
through the loop and Quick Link.
Remove the cross bar (AA) from the canopy (E) by loosening the
nuts (CC).
Fix the cross bar using the junction box mounting screws (FF)
provided.
C12” rods
with pre-attached
loop (x2)
CC
CC
includes top nuts (x2) and
bolts (x2)
Junction Box
Bolts (x2)
Canopy Bolt (x4)
DD
Crossbar Hardware
A
Bolts and
top nuts
Step
A & B
Step
C & D
Steps
E, F, G
B
E
C
EE
A
Figure 2
AA
DD
FF
Figure 3
Wire
Connector (x3)
GG
Wire
Connector (x3)
HH
Note: You can reduce the height of the fixture by not using
either or both of the rods (B and C) provided.
A.
B.
C.
D.
E.
F.
G.
2of2
STEP4-InstallFixtureAttachment to
Ceiling
Attach the canopy to the fixture handle
through the Quick Links (EE).
Pass the slack wire and ground wire
through the loop in the canopy
Lift the fixture body with canopy up
towards the cross bar which was
attached in Step 3.
Figure 5
Whitewire
fromsupplyRibbedsideofwirefromfixture
identifiedwiththeLabel“N”
Blackwirefrom
supply(orRed)
Smoothside of wirefromfixture
identifiedwiththelabel“L”
Groundwire
fromsupply
Groundwire
fromfixture
A.
B.
C.
Pass the bolt (DD) from the
cross bar through the hole
in the canopy and tighten
using the top nuts (CC).
B.
Use the included wire connectors to make all the wire
connections. Twist connectors until wires are tightly joined
together. Wrap each connection with approved electrical tape
and carefully stuff connected wires into outlet box. See Figure 6.
STEP5-Wire Connections
A.
D
Figure 4
Figure 6
CC
DD
EE
Figure 7
Optional: Flush Mount Installation
Pull the slack wire and ground wire and pass through rod (E).
Thread rods (E) over the handle of the fixture body (A).
Lift the fixture with canopy attached towards the cross bar
already attached in Step 2.
Pass the bolt (DD) from the cross bar (AA) through the hole in
the canopy and tighten using the top nuts (CC).
A.
B.
D.
E.
C. Unscrew the loops from the canopy (D) (Figure 8) and thread the
other end of rods (E) directly to the canopy (D) (Figure 9).
Figure 8
Figure 9
Figure 10
  • Page 1 1
  • Page 2 2

urban ambiance UFS2011 Installation guide

Brand
urban ambiance
Model
UFS2011
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents