Automotive Products Division
1040 Avenida Acaso • Camarillo, CA 93012, U.S.A.
USA Sales (800) 336-6500
Canada Sales (888) 922-3006 • USA Fax (805) 388-7950
For information about other American International automotive
accessories visit our website at:
http://www.americaninternational.net
CUSTOMER HELP LINE
USA 800-323-4329 • Canada 800-245-8777
©2009 AMERICAN INTERNATIONAL INDUSTRIES, INC.
Ver. 4/09
TOY-K962 Mounting Kit
Toyota
2003-09 4 RUNNER LIMITED EDITION
2003-09 4 RUNNER SPORT EDITION with RDS RADIO
VEHICLE APPLICATIONS
iTOYK962
Optional: ISO trim ring
may be used in place of
after-market radio’s trim ring.
1. Attach ISO mount brackets to rear of kit as shown below and attach to rear of pocket
using small screws provided with kit.
2. Attach (1) ISO Spacer to the inside of both Left & Right mounting brackets as shown
in Fig. A below.
3. Insert ISO mountable radio between ISO mount brackets and loosely attach to sides
of radio using screws provided with radio when possible or screws supplied with kit.
4. Attach ISO trim ring to face of kit.
5. Slide radio forward or backward for desired look and tighten screws.
1. Attach mounting brackets to rear of kit as shown below and secure to rear of pocket
using small screws provided with kit.
2. Insert DIN sleeve from your new radio into the opening of the installation kit.
3. Depress the tabs from inside the sleeves opening upward, outward, and
downward to secure sleeve to the installation kit.
ISO Trim Ring
(Use Optional)
DIN MOUNT INSTRUCTIONS
ISO MOUNT INSTRUCTIONS
1 2
Insert spacers
into brackets on
both sides only
when ISO
mounting radio.
See Fig. A
1. Open the center pocket below the climate controls and remove the (1) 10 mm bolt.
2. Open the Center console rear pocket lid.
3. Carefully Unclip the forward part of the center console section with ashtray trim,
disconnect the harness and remove console section.
4. Carefully unclip and remove the trim ring from around the key cylinder.
5. Carefully lift the center console side covering and remove.
6. Remove the (2) lower 10 mm bolts from the bottom of driver side under dash panel.
7. Carefully pull drivers side under dash panel outward and lay out of the way.
8. Remove the (1) 10mm bolt at the lower edge of the radio trim bezel on the driver side.
9. Unclip the trim from the front of the center console pocket.
10. Carefully pry outward the climate control pod, disconnect the wire harness and
remove pod.
11. Remove the (2) 10mm bolts from behind the climate control location.
12. Carefully unclip the entire radio/climate control trim bezel, disconnect all harnesses
from bezel and remove.
13. Remove the (2) 10mm bolts securing the factory radio to the sub-dash.
14. Carefully pull radio forward, disconnect all harnesses and antenna leads and
remove radio.
DASH DISASSEMBLY INSTRUCTIONS
2003-08 TOYOTA 4 RUNNER
ISO Trim Ring
(Use Optional)
For ISO mount only: Attach (1) ISO
Spacer to the inside of upper section
on both Left & Right mounting
brackets as shown in Fig. A
Fig. A
Optional: ISO trim ring
may be used in place of
after-market radio’s trim ring.
-
1
-
2
PAC TOYK962 User manual
- Type
- User manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Metra 99-8300 Installation guide
-
American International TOYK994 User manual
-
American International GMK422 User manual
-
-
-
-
-
-
Metra Electronics 99-8218 User manual
-
Metra Electronics 952001 User manual
