Supermicro H8DMR-I2 User manual

H8DMR-82

H8DMR-i2

USER’S MANUAL

Revision 1.0d

SUPER

®

Manual Revision 1.0d

Release Date: March 13, 2009

The information in this User’s Manual has been carefully reviewed and is believed to be accurate.

The vendor assumes no responsibility for any inaccuracies that may be contained in this document,

makes no commitment to update or to keep current the information in this manual, or to notify any

person or organization of the updates. Please Note: For the most up-to-date version of this

manual, please see our web site at www.supermicro.com.

Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product

described in this manual at any time and without notice. This product, including software, if any,

and documentation may not, in whole or in part, be copied, photocopied, reproduced, translated or

reduced to any medium or machine without prior written consent.

IN NO EVENT WILL SUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL,

SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO

USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF

SUCH DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY

HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE PRODUCT, INCLUDING THE

COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH

HARDWARE, SOFTWARE, OR DATA.

Any disputes arising between manufacturer and customer shall be governed by the laws of Santa

Clara County in the State of California, USA. The State of California, County of Santa Clara shall

be the exclusive venue for the resolution of any such disputes. Super Micro's total liability for

all claims will not exceed the price paid for the hardware product.

FCC Statement: This equipment has been tested and found to comply with the limits for a Class

A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the manufacturer’s instruction manual, may cause harmful

interference with radio communications. Operation of this equipment in a residential area is likely

to cause harmful interference, in which case you will be required to correct the interference at your

own expense.

California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate

warning applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate

Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate”

WARNING: Handling of lead solder materials used in this

product may expose you to lead, a chemical known to

the State of California to cause birth defects and other

reproductive harm.

Unless you request and receive written permission from Super Micro Computer, Inc., you may not

copy any part of this document.

Information in this document is subject to change without notice. Other products and companies

referred to herein are trademarks or registered trademarks of their respective companies or mark

holders.

Printed in the United States of America

Preface

iii

Preface

About This Manual

This manual is written for system integrators, PC technicians and

knowledgeable PC users. It provides information for the installation and use of the

H8DMR-82/H8DMR-i2 serverboard. The H8DMR-82/H8DMR-i2 is based on the

nVidia® MCP55 Pro/NEC uPD720400 chipset and supports single or dual AMD

Opteron

TM

2000 Series Socket F type processors and up to 64 GB of DDR2-667

/533/400 registered ECC SDRAM.

Please refer to the serverboard speciﬁ cations pages on our web site for updates on

supported processors (http://www.supermicro.com/aplus/). This product is intended

to be professionally installed.

Manual Organization

Chapter 1 includes a checklist of what should be included in your serverboard

box, describes the features, speciﬁ cations and performance of the serverboard and

provides detailed information about the chipset.

Chapter 2 begins with instructions on handling static-sensitive devices. Read this

chapter when installing the processor(s) and memory modules and when installing

the serverboard in a chassis. Also refer to this chapter to connect the ﬂ oppy and

hard disk drives, the serial ports, the mouse and keyboard and the twisted wires

for the power and reset buttons and the system LEDs.

If you encounter any problems, see Chapter 3, which describes troubleshooting

procedures for the video, the memory and the setup conﬁ guration stored in CMOS.

For quick reference, a general FAQ (Frequently Asked Questions) section is pro-

vided. Instructions are also included for contacting technical support. In addition,

you can visit our web site for more detailed information.

Chapter 4 includes an introduction to BIOS and provides detailed information on

running the CMOS Setup utility.

Appendix A provides BIOS Error Beep Code Messages.

Appendix B lists BIOS POST Checkpoint Codes.

H8DMR-82/H8DMR-i2 User’s Manual

Table of Contents

Preface

About This Manual ...................................................................................................... iii

Manual Organization ................................................................................................... iii

Chapter 1: Introduction

1-1 Overview ......................................................................................................... 1-1

Checklist ................................................................................................... 1-1

H8DMR-82/H8DMR-i2 Image ................................................................... 1-3

H8DMR-82/H8DMR-i2 Serverboard Layout ............................................. 1-4

H8DMR-82/H8DMR-i2 Quick Reference .................................................. 1-5

Serverboard Features .............................................................................. 1-6

nVidia MCP55 Pro Chipset: System Block Diagram ............................... 1-8

1-2 Chipset Overview ........................................................................................... 1-9

1-3 PC Health Monitoring ................................................................................... 1-10

1-4 Power Conﬁ guration Settings ....................................................................... 1-11

1-5 Power Supply ............................................................................................... 1-12

1-6 Super I/O ........................................................................................................1-13

Chapter 2: Installation

2-1 Static-Sensitive Devices ................................................................................. 2-1

2-2 Processor and Heatsink Installation ............................................................... 2-2

2-3 Mounting the Serverboard into a Chassis ...................................................... 2-5

2-4 Installing Memory ........................................................................................... 2-5

2-5 I/O Port and Control Panel Connections ........................................................ 2-8

2-6 Connecting Cables ......................................................................................... 2-9

ATX Power Connector .............................................................................. 2-9

Processor Power Connector .................................................................... 2-9

Auxiliary Power Connector ....................................................................... 2-9

MNI Button ............................................................................................... 2-9

Power LED ............................................................................................. 2-10

HDD LED ............................................................................................... 2-10

NIC1 LED ............................................................................................... 2-10

NIC2 LED ............................................................................................... 2-10

Overheat/Fan Fail LED .......................................................................... 2-10

Power Fail LED ...................................................................................... 2-11

Reset Button .......................................................................................... 2-11

Power Button .......................................................................................... 2-11

iv

v

Table of Contents

USB Ports .............................................................................................. 2-11

USB Headers ......................................................................................... 2-12

Serial Ports ............................................................................................. 2-12

Fan Headers .......................................................................................... 2-12

JLAN1/2 (Ethernet Ports) ....................................................................... 2-12

Power LED/Speaker ............................................................................... 2-13

ATX PS/2 Keyboard/Mouse Ports .......................................................... 2-13

Chassis Intrusion .................................................................................... 2-13

Overheat LED ........................................................................................ 2-13

Wake-On-LAN ........................................................................................ 2-14

Wake-On-Ring ........................................................................................ 2-14

PWR I

2

C ................................................................................................. 2-14

IPMB ....................................................................................................... 2-14

3rd Power Supply Alarm Header ........................................................... 2-15

Compact Flash Card PWR Connector ................................................... 2-15

SGPIO .................................................................................................... 2-15

Power Fail Header ................................................................................. 2-16

2-7 Jumper Settings ............................................................................................ 2-16

Explanation of Jumpers ......................................................................... 2-16

CMOS Clear ........................................................................................... 2-17

3rd Power Supply Fail Detect Enable/Disable ....................................... 2-17

VGA Enable/Disable ............................................................................... 2-17

Watch Dog Enable/Disable .................................................................... 2-18

PCI-X Slot Freq. Select .......................................................................... 2-18

I

2

C to PCI Enable/Disable ...................................................................... 2-18

Compact Flash Master/Slave ................................................................. 2-19

SCSI Controller Enable/Disable ............................................................. 2-19

SCSI Termination Enable/Disable .......................................................... 2-19

2-8 Onboard Indicators ....................................................................................... 2-20

LAN1/LAN2 LEDs .................................................................................. 2-20

+5V Standby Power LED ....................................................................... 2-20

SCSI Activity LEDs ................................................................................. 2-20

2-9 Floppy, IDE, SATA and SCSI Drive Connections ......................................... 2-21

Floppy Connector ................................................................................... 2-21

IDE Connectors ...................................................................................... 2-22

SATA Ports ............................................................................................. 2-22

SCSI Connectors ................................................................................... 2-23

H8DMR-82/H8DMR-i2 User’s Manual

2-10 Enabling SATA RAID .................................................................................... 2-24

2-11 Installing Additional Drivers .......................................................................... 2-26

Chapter 3: Troubleshooting

3-1 Troubleshooting Procedures ........................................................................... 3-1

Before Power On ..................................................................................... 3-1

No Power ................................................................................................. 3-1

No Video .................................................................................................. 3-1

Memory Errors ......................................................................................... 3-2

Losing the System’s Setup Conﬁ guration ................................................ 3-2

3-2 Technical Support Procedures ........................................................................ 3-2

3-3 Frequently Asked Questions ........................................................................... 3-3

3-4 Returning Merchandise for Service ................................................................ 3-4

Chapter 4: BIOS

4-1 Introduction ..................................................................................................... 4-1

4-2 Main Menu ...................................................................................................... 4-2

4-3 Advanced Settings Menu ............................................................................... 4-2

4-4 Boot Menu .................................................................................................... 4-16

4-5 Security Menu ............................................................................................... 4-17

4-6 Exit Menu ...................................................................................................... 4-18

Appendices

Appendix A: BIOS Error Beep Codes ...................................................................... A-1

Appendix B: BIOS POST Checkpoint Codes ........................................................... B-1

vi

Chapter 1: Introduction

1-1

Chapter 1

Introduction

1-1 Overview

Checklist

Congratulations on purchasing your computer serverboard from an acknowledged

leader in the industry. Our boards are designed with the utmost attention to detail

to provide you with the highest standards in quality and performance.

Please check that the following items have all been included with your serverboard.

If anything listed here is damaged or missing, contact your retailer.

Included with retail box only

 One (1) H8DMR-82/H8DMR-i2 serverboard

 One (1) IDE cable (CBL-036L-02)

 One (1) ﬂ oppy cable (CBL-022L)

 Two (2) heatsink retention modules with four (4) screws (BKT-0012L)

 One (1) CD containing drivers and utilities

1-2

H8DMR-82/H8DMR-i2 User’s Manual

Contacting Supermicro

Headquarters

Address: Super Micro Computer, Inc.

980 Rock Ave.

San Jose, CA 95131 U.S.A.

Tel: +1 (408) 503-8000

Fax: +1 (408) 503-8008

Email: [email protected] (General Information)

[email protected] (Technical Support)

Web Site: www.supermicro.com

Europe

Address: Super Micro Computer B.V.

Het Sterrenbeeld 28, 5215 ML

's-Hertogenbosch, The Netherlands

Tel: +31 (0) 73-6400390

Fax: +31 (0) 73-6416525

Email: [email protected] (General Information)

[email protected] (Technical Support)

[email protected] (Customer Support)

Asia-Paciﬁ c

Address: Super Micro Computer, Inc.

4F, No. 232-1, Liancheng Rd.

Chung-Ho 235, Taipei County

Taiwan, R.O.C.

Tel: +886-(2) 8226-3990

Fax: +886-(2) 8226-3991

Web Site: www.supermicro.com.tw

Technical Support:

Email: [email protected]

Tel: 886-2-8228-1366, ext.132 or 139

Chapter 1: Introduction

1-3

Note:

The H8DMR-82 is pictured. The H8DMR-i2 shares the same layout but with no SCSI

components, connectors or jumpers.

Figure 1-1. H8DMR-82/H8DMR-i2 Image

1-4

H8DMR-82/H8DMR-i2 User’s Manual

Notes:

1. Jumpers not indicated are for test purposes only.

2. The H8DMR-i2 has the same layout as the H8DMR-82 but with no SCSI compo-

nents, connectors or jumpers.

Figure 1-2. H8DMR-82/H8DMR-i2 Serverboard Layout

(not drawn to scale)

NEC

uPD720400

ATI

ES1000

BIOS

KBMSE

USB0

/1

VGA

Battery

SIM1U

DIMM 1B

DIMM 1A

DIMM 2B

DIMM 2A

J32 JPW1

JPW2

JF1

CPU2

CPU1

DIMM 2A

DIMM 2B

DIMM 1A

DIMM 1B

SATA1

SATA0

SATA3

SATA2

SATA5

SATA4

JIDE1

JFDD1

U320 SCSI CH A

COM2

nVidia

MCP55

AIC-7902W

Slot 6: 133 MHz PCI-X

Slot 7: 100 MHz PCI-X (ZCR)

PCI-Exp x8

LAN1LAN2

U320 SCSI CH B

JBT1

COM1

Speaker

JB1

JA1

JPA3

JPG1

JI

2

C1/JI

2

C2

JPX1A/JPX1B

JOH1

JWOR

JWD

IPMB

JAR

J3P

JPWF

PWR I

2

C

FAN1

FAN3

FAN2

FAN4

FAN5

JPA2

JCF1

JWF1

JD1

USB2/3

JWOL

JL1

JPA1

SGPIO1

SGPIO2

SUPER H8DMR-82

DA1

DA2

DA4

Chapter 1: Introduction

1-5

H8DMR-82/H8DMR-i2 Quick Reference

Jumpers Description Default Setting

J3P 3rd Power Fail Detect En/Dis Closed (Enabled)

JBT1 CMOS Clear See Section 2-7

JCF1 Compact Flash Master/Slave Closed (Master)

JI

2

C1/2 I

2

C to PCI Enable/Disable Closed (Enabled)

JPA1* SCSI Enable/Disable Pins 1-2 (Enabled)

JPA2/JPA3* SCSI Channel A/B Term. Open (Enabled)

JPG1 VGA Enable/Disable Pins 1-2 (Enabled)

JPX1A PCI-X Slot #6 Freq. Select Open (Auto)

JPX1B PCI-X Slots #7 Freq. Select Open (Auto)

JWD Watch Dog Pins 1-2 (Reset)

Connectors Description

COM1, COM2 COM1/COM2 Serial Port/Header

FAN 1-5 System Fan Headers

IPMB System Management Bus Header

J32 4-pin Auxiliary Power Connector

JA1* U320 SCSI Channel A Connector

JAR 3rd Power Supply Alarm Reset Header

JB1* U320 SCSI Channel B Connector

JD1 Onboard Speaker/Keylock/Power LED

JF1 Front Panel Connector

JFDD1 Floppy Disk Drive Connector

JIDE1 IDE Drive Connector

JL1 Chassis Intrusion Header

JOH1 Overheat Warning Header

JPW1 20-Pin ATX Power Connector

JPW2 8-Pin Processor Power Connector

JPWF Power Fail Header

JWF1 Compact Flash Card Power Connector

JWOL Wake-On-LAN Header

JWOR Wake-On-Ring Header

LAN1/2 Gigabit Ethernet (RJ45) Ports

PWR I

2

C Power Supply I

2

C Header

SATA0 ~ SATA5 Serial ATA Ports

SGPIO1/SGPIO2 SGPIO Headers

SIM1U IPMI Card Slot

USB0/1 Universal Serial Bus (USB) Ports 0/1

USB2/3 Additional USB Headers

*H8DMR-82 only

1-6

H8DMR-82/H8DMR-i2 User’s Manual

Serverboard Features

CPU

• Single or dual AMD Opteron 2000 Series Socket F type 64-bit processors

Memory

• Eight dual/single channel DIMM slots supporting up to 64 GB of DDR2-667

/533/400 registered ECC SDRAM

Note: Memory capacities are halved for single CPU systems. Refer to Section 2-4 before installing.

Chipset

• nVidia MCP55 Pro

• NEC uPD720400

Expansion Slots

• One (1) Universal PCI-X 133 MHz slot

• One (1) Universal PCI-X 100 MHz slot (supports ZCR on H8DMR-82 only)

• Two (2) PCI-Express x8 slots

• One (1) SIM1U slot (for IPMI card)

BIOS

• 8 Mb AMIBIOS

®

LPC Flash ROM

• DMI 2.3, PCI 2.2, ACPI 2.0, Plug and Play (PnP)

PC Health Monitoring

• Onboard voltage monitors for two CPU cores, Hyper Transport (1.2V), memory

banks (1.8V), chipset (1.5V)

• Fan status monitor with ﬁ rmware/software on/off and speed control

• Watch Dog

• Environmental temperature monitoring via BIOS

• Power-up mode control for recovery from AC power loss

• System resource alert (via included utility program)

• Auto-switching voltage regulator for the CPU core

Chapter 1: Introduction

1-7

ACPI Features

• Slow blinking LED for suspend state indicator

• BIOS support for USB keyboard

• Main switch override mechanism

• Internal/external modem ring-on

Onboard I/O

• On-chip SATA controller supporting six (6) SATA ports (RAID 0, 1, 0+1 and 5)

• Adaptec AIC-7902W SCSI controller (RAID 0, 1 and 10, H8DMR-82 only)

• One (1) UltraDMA (ATA) 133/100 IDE port

• One (1) ﬂ oppy port interface (up to 2.88 MB)

• Two (2) Fast UART 16550 compatible serial ports

• On-chip (nVidia MCP55) Ethernet controller supports two Gigabit LAN ports

• ATI RN50 (ES1000) onboard graphics controller

• PS/2 mouse and PS/2 keyboard ports

• Four (4) USB (Universal Serial Bus) 2.0 ports/headers

Other

• Wake-on-Ring

• Wake-on-LAN

• Onboard +5V power LED (DA4)

• SCSI channel activity LEDs (DA1, DA2, H8DMR-82 only)

• Chassis intrusion detection

CD Utilities

• BIOS ﬂ ash upgrade utility

Dimensions

• Extended ATX form factor, 12" x 13.05" (305 x 332 mm)

1-8

H8DMR-82/H8DMR-i2 User’s Manual

Figure 1-3. nVidia MCP55 Pro/NEC uPD720400 Chipset:

System Block Diagram

Note: This is a general block diagram and may not exactly represent

the features on your serverboard. See the previous pages for the

actual speciﬁ cations of your serverboard.

MCP55 Pro

AMD Opteron

TM

Processor (CPU2)

16 x 16 HT link (1 GHz)

DIMM 1B

DIMM 1A

128-bit data + 16-bit ECC

DDR2-667/533/400 DDR2-667/533/400

PCI-E x8 Slot

PCI-X 133 MHz Slot

SATA Ports (6)

IDE (ATA133)

USB Ports (4)

S I/O BIOS

Floppy

Kybd/

Mouse

Serial Ports

(2)

AMD Opteron

TM

Processor (CPU1)

128-bit data + 16-bit ECC

AIC 7902W

PCI-X

CH A

PCI-X

CH B

SCSI Ports (2)

LPC

DIMM 2B

DIMM 2A

DIMM 2B

DIMM 1A

DIMM 1B

IPMI

NEC uPD720400

PCI-X 100 MHz Slot

PCI-E x8 Slot

ATI RN50

x8 PCI-E Bus

GLAN Ports (2)

Chapter 1: Introduction

1-9

1-2 Chipset Overview

The H8DMR-82/H8DMR-i2 serverboard is based on the nVidia MCP55 Pro/NEC

uPD720400 chipset. The nVidia MCP55 Pro functions as Media and Communica-

tions Processor (MCP) and the NEC chip as a PCI-X Tunnel. Controllers for the

system memory are integrated directly into the AMD Opteron processors.

MCP55 Pro Media and Communications Processor

The MCP55 Pro is a single-chip, high-performance HyperTransport peripheral con-

troller. It includes a 28-lane PCI Express interface, an AMD Opteron 16-bit Hyper

Transport interface link, a six-port Serial ATA interface, a dual-port Gb Ethernet

interface, an ATA133/100 bus master interface and a USB 2.0 interface. This hub

connects directly to CPU#1 and through that to CPU#2.

NEC uPD720400

This I/O bridge chip provides two PCI-X domains. Each bridge supports PCI

masters that include clock, request and grant signals. This hub connects to the

MCP55 Pro through a PCI-Express x8 Bus. It also interfaces directly with the

Adaptec SCSI controller.

HyperTransport Technology

HyperTransport technology is a high-speed, low latency point to point link that was

designed to increase the communication speed by a factor of up to 48x between

integrated circuits. This is done partly by reducing the number of buses in the

chipset to reduce bottlenecks and by enabling a more efﬁ cient use of memory in

multi-processor systems. The end result is a signiﬁ cant increase in bandwidth

within the chipset.

1-10

H8DMR-82/H8DMR-i2 User’s Manual

1-3 PC Health Monitoring

This section describes the PC health monitoring features of the H8DMR-82/H8DMR-

i2. The serverboard has an onboard System Hardware Monitor chip that supports

PC health monitoring.

Onboard Voltage Monitors for two CPU cores, Hyper Transport

(1.2V), memory banks (1.8V), chipset (1.5V)

The onboard voltage monitor will scan these voltages continuously. Once a voltage

becomes unstable, it will give a warning or send an error message to the screen.

Users can adjust the voltage thresholds to deﬁ ne the sensitivity of the voltage moni-

tor. Real time readings of these voltage levels are all displayed in BIOS.

Fan Status Monitor with Firmware/Software Speed Control

The PC health monitor can check the RPM status of the cooling fans. The onboard

fans are controlled by thermal management via BIOS.

CPU Overheat/Fan Fail LED and Control

This feature is available when the user enables the CPU overheat/Fan Fail warning

function in the BIOS. This allows the user to deﬁ ne an overheat temperature. When

this temperature is exceeded or when a fan failure occurs, then, the Overheat/Fan

Fail warning LED is triggered.

Auto-Switching Voltage Regulator for the CPU Core

The 3-phase-switching voltage regulator for the CPU core can support up to 80A and

auto-sense voltage IDs ranging from 0.8 V to 1.55V. This will allow the regulator

to run cooler and thus make the system more stable.

Chapter 1: Introduction

1-11

1-4 Power Conﬁ guration Settings

This section describes the features of your serverboard that deal with power and

power settings.

Slow Blinking LED for Suspend-State Indicator

When the CPU goes into a suspend state, the chassis power LED will start blinking

to indicate that the CPU is in suspend mode. When the user presses any key, the

CPU will wake-up and the LED will automatically stop blinking and remain on.

BIOS Support for USB Keyboard

If a USB keyboard is the only keyboard in the system, it will function like a normal

keyboard during system boot-up.

Main Switch Override Mechanism

When an ATX power supply is used, the power button can function as a system

suspend button. When the user depresses the power button, the system will enter

a SoftOff state. The monitor will be suspended and the hard drive will spin down.

Depressing the power button again will cause the whole system to wake-up. Dur-

ing the SoftOff state, the ATX power supply provides power to keep the required

circuitry in the system alive. In case the system malfunctions and you want to turn

off the power, just depress and hold the power button for 4 seconds. The power

will turn off and no power will be provided to the serverboard.

Wake-On-LAN (JWOL)

Wake-On-LAN is deﬁ ned as the ability of a management application to remotely

power up a computer that is powered off. Remote PC setup, up-dates and access

tracking can occur after hours and on weekends so that daily LAN trafﬁ c is kept

to a minimum and users are not interrupted. The serverboard has a 3-pin header

(JWOL) to connect to the 3-pin header on a Network Interface Card (NIC) that has

WOL capability. Wake-On-LAN must be enabled in BIOS. Note that Wake-On-LAN

can only be used with an ATX 2.01 (or above) compliant power supply.

Wake-On-Ring Header (JWOR)

Wake-up events can be triggered by a device such as the external modem ringing

when the system is in the SoftOff state. Note that external modem ring-on can only

be used with an ATX 2.01 (or above) compliant power supply.

1-12

H8DMR-82/H8DMR-i2 User’s Manual

1-5 Power Supply

As with all computer products, a stable power source is necessary for proper and

reliable operation. It is even more important for processors that have high CPU

clock rates.

The H8DMR-82/H8DMR-i2 accommodates 12V ATX power supplies. Although

most power supplies generally meet the speciﬁ cations required by the CPU, some

are inadequate. A 2 amp current supply on a 5V Standby rail is strongly recom-

mended.

It is strongly recommended that you use a high quality power supply that meets

12V ATX power supply Speciﬁ cation 1.1 or above. Additionally, in areas where

noisy power transmission is present, you may choose to install a line ﬁ lter to shield

the computer from noise. It is recommended that you also install a power surge

protector to help avoid problems caused by power surges.

Warning: To prevent the possibility of explosion, do not use the wrong type of

onboard CMOS battery or install it upside down.

Chapter 1: Introduction

1-13

1-6 Super I/O

The disk drive adapter functions of the Super I/O chip include a ﬂ oppy disk drive

controller that is compatible with industry standard 82077/765, a data separator,

write pre-compensation circuitry, decode logic, data rate selection, a clock genera-

tor, drive interface control logic and interrupt and DMA logic. The wide range of

functions integrated onto the Super I/O greatly reduces the number of components

required for interfacing with ﬂ oppy disk drives. The Super I/O supports two 360

K, 720 K, 1.2 M, 1.44 M or 2.88 M disk drives and data transfer rates of 250 Kb/s,

500 Kb/s or 1 Mb/s.

It also provides two high-speed, 16550 compatible serial communication ports

(UARTs), one of which supports serial infrared communication. Each UART in-

cludes a 16-byte send/receive FIFO, a programmable baud rate generator, complete

modem control capability and a processor interrupt system. Both UARTs provide

legacy speed with baud rate of up to 115.2 Kbps as well as an advanced speed

with baud rates of 250 K, 500 K, or 1 Mb/s, which support higher speed modems.

The Super I/O supports one PC-compatible printer port (SPP), Bi-directional Printer

Port (BPP) , Enhanced Parallel Port (EPP) or Extended Capabilities Port (ECP).

The Super I/O provides functions that comply with ACPI (Advanced Conﬁ guration

and Power Interface), which includes support of legacy and ACPI power manage-

ment through a SMI or SCI function pin. It also features auto power management

to reduce power consumption.

The IRQs, DMAs and I/O space resources of the Super I/O can be ﬂ exibly adjusted

to meet ISA PnP requirements, which support ACPI and APM (Advanced Power

Management).

1-14

H8DMR-82/H8DMR-i2 User’s Manual

Notes

Page is loading ...

Supermicro H8DMR-I2 User manual

This manual is also suitable for

Supermicro H8DMR-I2 User manual

Related papers

Other documents