Vetus Boat windows Installation guide

070301.01

NEDERLANDS 4

ENGLISH 6

DEUTSCH 8

FRANÇAIS 10

ESPAÑOL 12

ITALIANO 14

Bedieningshandleiding en

installatie instructies

Scheepsramen

Operation manual and

installation instructions

Boat Windows

Bedienungshandbuch und

Einbauanleitung

Bootsfenster

Manuel d’utilisation et

instructions d’installation

Fenêtres de bateau

Manual de manejo y

instrucciones de instalación

Ventanas de barco

Manuale per l’uso e

istruzioni per l’installazione

Finestrini

Boat windows

Page is loading ...

070301.013

vetus® Boat windows

Inhoud Content

1 Inleiding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

2 Pre-installatie glasinspectie

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

2.1 Acceptatiecriteria glaspanelen tot 0,6 m

2

. . . . . . . . . . . . . . . . . 4

2.2 Acceptatiecriteria glaspanelen groter dan 0,6

m

2

. . . . . . . . . . 4

3 Bediening. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

4 Montage

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

5 Onderhoud

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

6 Technische gegevens

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1 Einleitung

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2 Inspektion vor der Installation

. . . . . . . . . . . . . . . . . . . . . . . . . 8

2.1 Annahmekriterien für Glasscheiben bis zu 0,6 m

2

. . . . . . . . . 8

2.2 Annahmekriterien für Glasscheiben größer als 0,6 m

2

. . . . . 8

3 Bedienung

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

4 Montage

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

5 Wartung

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

6 Technische Daten

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

1 Introducción

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

2 Inspección antes de la instalación

. . . . . . . . . . . . . . . . . . . . . . 12

2.1 Criterio de aceptación de los paneles de vidrio de hasta

0,6 m

2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

2.2 Criterio de aceptación de los paneles de vidrio mayores

de 0,6

m

2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

3 Operación . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

4 Montaje

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

5 Mantenimiento

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

6 Datos técnicos

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

1 Introduction

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

2 Inspection avant installation

. . . . . . . . . . . . . . . . . . . . . . . . . . 10

2.1 Critères d’acceptation des vitrages jusqu’à 0,6 m

2

. . . . . . . . 10

2.2 Critères d’acceptation des vitrages de plus de 0,6 m

2

. . . . . 10

3 Commande

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

4 Montage

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

5 Entretien

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

6 Fiche technique

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

1 Introduzione

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

2 Ispezione prima dell’installazione

. . . . . . . . . . . . . . . . . . . . . . 14

2.1 Criteri di accettazione per lastre di vetro no a 0,6 m

2

. . . . 14

2.2 Criteri di accettazione lastre di vetro più larghe di 0,6 m

2

14

3 Funzionamento

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

4 Montaggio

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

5 Manutenzione

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

6 Dati tecnici

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

1 Introduction

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2 Pre-installation inspection

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2.1 Acceptance criteria glass panes up to 0,6 m

2

(6 sq. ft.) . . . . . 6

2.2 Acceptance criteria glass panes lager than 0,6 m

2

(6 sq. ft.) 6

3 Operating

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

4 Fitting

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

5 Maintenance

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

6 Technical Data

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Inhalt Sommaire

Índice Indice

Page is loading ...

6070301.01

vetus® Boat windows

1 Introduction

This Manual applies to Vetus/Marex ship windows with aluminium

proles; the screw on range, comfort range and exclusive range.

2 Pre-installation inspection

important

Check the glass immediately after unpacking

• Determine center area (A) and calculate the edge area:

- The distance B1 shown in the drawing is calculated as follows:

B1 = H x 5%

- The distance B2 shown in the drawing is calculated as follows:

B2 = W x 5%

• Clean the glass.

• Check the glass in daylight, never in direct sunlight.

• Inspect the glass at a 90 degree angle.

Defects examples: debris, spots, bubbles, scratch, local distortion.

2.1 Acceptance criteria glass panes up to 0,6 m

2

(6 sq. ft.)

Central area

- One defect smaller than 1.6 mm (

1

/

16

”) and viewable from 1.5 me-

ters (4.9 ft).

- No scratches.

Border area

Not more than one defect, in total, as described below:

- Defect smaller than 1.6 mm (

1

/

16

”) and viewable from 3 meters

(9.8 ft).

- Sratch shorter than 12 mm (

1

/

2

”) and viewable from 3 meters

(9.8 ft.)

2.2 Acceptance criteria glass panes lager than 0,6 m

2

(6 sq. ft.)

Central area

- Two defects smaller than 1.6 mm (

1

/

16

”) and viewable from 1.5

meters (4.9 ft).

- No scratches.

Border area

Not more than two defects, in total, as described below:

- Defect smaller than 1.6 mm (

1

/

16

”) and viewable from 3 meters

(9.8 ft).

- Scratch shorter than 12 mm (

1

/

2

”) and viewable from 3 meters

(9.8 ft).

3 Operating

Whole and Half-Opening Windows:

Opening:

• Release the extension arm handles by about 2 turns (to the left),

turn both extension arms inwards while pushing the window out

at the same time.

• Lock the window in the open position by tightening up both han-

dles again.

Closing:

• Release the extension arm handles by about 2 turns, rst pull both

extension arms inward and then turn them towards the window

frame to close the window.

• Lock the window in the closed position by tightening up both

handles again.

4 Fitting

Fixed Window with round corners:

It is possible to t the window in a slightly curved wall. A curve of

maximum 3 cm. per metre is possible. With a high window more than

30 cm. high, the curve should be less, or completely at.

Fixed Window with double glass and condensation gutter:

Fit the aluminium window frame in a completely at surface only!

Hinged Window:

Fit the aluminium window frame in a completely at surface only!

If tted in a curved surface, the hinges will be overloaded!

H

W

A

B1

B2

1

070301.017

vetus® Boat windows

Slide and Drop Windows:

Fit the aluminium window frame in a completely at surface only!

The window will jam or slide badly in a curved surface!

Cutting the Hole

Draw the hole to be cut out using the the window.

Remove burrs and smooth the edges.

Warning

Dust created when working with glass-bre reinforced polyes-

ter is hazardous to lungs and eyes. So always wear a dust mask

and protective goggles. Ventilate the working area properly.

Comfort and exclusive range:

The windows of the comfort and exclusive range are xed through a

clamp construction. Holes for xing screws do not have to be drilled

in the wall in which the window is tted. The length of the screws

supplied is based on the specied wall thickness.

The window frame already has a rubber. Do not apply any sealant!

• Fit the window in the hole (from the outside!); the backplate must

rst be carefully removed.

• Fit the backplate (on the inside!). If required, use a rubber or plas-

tic-faced hammer to tap the backplate into the frame. During t-

ting, press the backplate against the frame regularly.

• When pressing on the outside, apply pressure to the frame and

NOT the glass! Sliding windows must be tted in the closed posi-

tion.

Screw-on range:

The windows of the screw-on range are fastend from the outside.

The screws are not included. These windows are supplied with a

foam rubber (inseal) for a watertight installation. Do not apply any

sealant!

• Do not apply the foam rubber yet!

• Place the window (from the outside!) in the opening; mark where

the holes for the xing screws, remove the window and pre-drill

the holes.

• Attach the foam rubber to the window, place the window in the

opening and secure with the screws.

• When pressing on the outside, apply pressure to the frame and

NOT the glass! Sliding windows must be tted in the closed posi-

tion.

For a window with round corners: Fit the backplate, starting with the

seam. Do not tighten up the screws until at least 3 corners of the

backplate are clamped in the window prole. This will avoid tting

problems with the third or fourth corner.

5 Maintenance

• Clean the anodized or powder coated aluminium proles regu-

larly: 2 to 4 times a year, depending on how dirty they are.

• Only use neutral cleaning agents. DO NOT use alkaline, acidic or

abrasive agents for cleaning the wndow frames or to remove ad-

hesive residues from the glass.

11

(

7

/

16

”)

35 (1

3

/

8

”)

3-12 / 12-20

(

1

/

8

”-

1

/

2

” /

1

/

2

”-

13

/

16

” )

1

2

11

(

7

/

16

”)

35 (1

3

/

8

”)

3-12 / 12-20

(

1

/

8

”-

1

/

2

” /

1

/

2

”-

13

/

16

” )

1

2

• After cleaning, apply a thin coat of transparent wax for protection.

• Protect the hinged window sealing rubbers with talcum powder.

important

Sliding Windows: Keep the running channel (1) free of sand,

dirt and algae; spray 1 to 2 times a year with silicon spray.

Check regularly to see whether the drain holes (2) are open.

6 Technical Data

Aluminium prole material : AlMgSi0.5

Glass thickness

- Screw on range : 6 or 8 mm

- Comfort range : 6, 8 or 10 mm

- Exclusive range : Insulating glass 6-8-6 mm

ENGLISH

Page is loading ...

vetus b.v.

FOKKERSTRAAT 571 - 3125 BD SCHIEDAM - HOLLAND

TEL.: +31 0(0)88 4884700 - [email protected] - www.vetus.com

Printed in the Netherlands

070301.01 2020-11

Vetus Boat windows Installation guide

Vetus Boat windows Installation guide

in other languages

Related papers

Other documents