Dometic NDA1402 Installation guide

Type
Installation guide

This manual is also suitable for

FOR YOUR SAFETY POUR VOTRE SECURITE
If you smell gas: Si vous sentez une odeur de gaz:
1. Open windows. 1.Ouvrez les fenetres.
2. Don't touch electrical switches. 2.Netouchez
a
aucun interrupteur.
3. Extinguish any open flame. 3.Eteignez toute flamme nue.
4. Immediately call your gas supplier. 4.Avertissez lmmediaternent votre
fournisseur de gaz.
FOR YOUR SAFETY POUR VOTRE SECURITE
Do not store or use gasoline or other Ne pas entreposer ni utiliser de I'essence
flammable vapors and liquids in the ni d'autres vapeurs ou liquides inflamma-
vicinity of this or any other appliance. bles
a
proxlmite de cet appareil ou de tout
autre appareil.
mn
Dometic
NEA1402
NDA1402
autodefrost
A
WARNING
Improper installation, adjustment,
alteration, service or maintenance can
cause injury or property damage. Refer to
this manual. For assistance or additional
information consult a qualified installer,
service agency or the gas supplier.
A
WARNING
If the refrigerator stops cooling - or - if
ammonia emanates from it, immediately
turn the refrigerator off and contact a
Service Center.
INSTALLATION
MANUAL
A
AVERTISSEMENT
Une installation, un reglage, une modifi-
cation, une reparation ou un entretien non
conforme aux normes peut entrainer des
blessures ou des dommages materiels.
Lisez attentivement Ie mode d'emploi
fourni avec I'appareil. Pour obtenir de
I'aide ou des renseignements supplernen-
taires, consultez un installateur ou un
service d'entretien quallfie ou Iefournis-
seur de gaz.
A
AVERTISSEMENT
I
Si Ie retrigerateur cesse de refroidir - ou - si
de I'ammoniac s'en degage, arretez irnrne-
diatement Ie retrigerateur et contactez un
centre de reparation.
mD
D0111etic
Corporate Office
2320 Industrial Parkway Elkhart, IN 46516
For Service Center Assistance
Call: 800-544-4881
USA
Service Office
Dometic, LLC
2320 Industrial Pkwy.
Elkhart, IN 46516
Phone: 574-294-2511
CANADA
Dometic, LLC
46 Zatonski, Unit 3
Brantford, ON, N3T 5L8
CANADA
Phone: 519-720-9578
825125902
©2006-2009. LLC
LaGrange, IN 46761
M00938
INTRODUCTION
3
CERTIFICATION AND CODE REQUIREMENTS
3
VENTILATION REQUIREMENTS
3
INSTALLATION PROCEDURE 5
APPENDIX A - REARVIEW EQUIPMENT. 10
APPENDIX B - WIRING DIAGRAMS 13
SYMBOLS
The following symbols are used throughout the manual:
AWARNING Indicates a potentially hazardous situation, which, if not avoided, could result
in death or serious injury.
A
CAUTION
Indicates a potentially hazardous situation, which, if not avoided, may result in
minor or moderate injury.
CAUTION Used without the safety alert symbol indicates, a potentially hazardous situation which, if not avoided
may result in property damage.
Information
Step-by-step instructions
This product is manufactured under
license of U.S. Patent Number 6.019,447.
Patents pending
U.S.
101619,675
U.S.
101620,177
U.S. 101758,174
U.S. 101758,175
U.S. 101760,564
U.S. 101760.565
- 2 -
This manual describes how to install NEAl 402 (all-electric operation) and NDA1402 (2-way operation). These models can be
equipped with an ice maker, an ice dispenser or ice
&
water dispensers.
The information in this manual is intended for qualified technicians with knowledge and experience of absorption refrigerators
and LP gas systems. For operating instructions, please refer to the User manual for the appliance in question.
Read this manual before installing the refrigerator. Comply with installation specifications and dimensions. Follow the instructions
to ensure that the refrigerator is installed safely and that it runs efficiently. Be aware of possible safety hazards when seeing alert
symbols on the refrigerator as well as in this manual.
The appliance is certified under the latest edition of ANSI Z21.19·CSA
104
Refrigerators using gas fuel. The installation must
conform with local codes, or in absence of local codes, the following standards as applicable.
In the U.S. the installation must conform with:
• National Fuel Gas Code, ANSI Z223 .IINFPA 54 (latest edi-
tion).
Recreational Vehicles Code, ANSI A 119.2 (latest edition)
• Manufactured Home Construction and Safety Standard, Title
24 CFR, Part 3280.
If an external electrical source is utilized, the refrigerator, when
installed, must be electrically grounded in accordance with lo-
cal codes or, in the absence of local codes, the National Electri-
cal Code, ANSIINFPA 70 - (latest edition).
In CANADA, the installation must conform with:
Natural Gas and Propane Installation Code, CSA B 149.1
• CSA Z240 RV Series, Recreational Vehicles.
• Current CSA
Z24004,
Gas-equipped Recreational Vehicles
and Mobile Housing.
If an external electrical source is utilized, the refrigerator,
when installed, must be electrically grounded in accordance
with local codes or, in the absence of local codes, the Canadian
Electrical Code, CSA C22.1, Parts I and II - (latest edition).
@.
C US
GENERAL INFORMATION
Provide necessary air circulation over the cooling unit. Open-
ings for air supply or for venting of combustion products shall
have a minimum dimension of not less than 1/4 inch.
Certified installations require one roof vent and one lower side
vent. Proper installation requires one lower fresh air intake
and one upper exhaust vent. The ventilation kits shown in this
manual have been certified for use with NEA1402 and
NDA1402. The ventilation kits must be installed and used
without modification.
Certified vent system kits
Kit no. Components Part no.
5A Roof Base 3103633.xXX*
Roof Cover 3103634.XXX*
Lower Side Vent 3109349.XXX*
Power Vent Asm. 3108705.744**
*
Fill in '~\XX" with color code numbers. For color codes, contact
your supplier.
**
Alternate instructions forwarded with the Ventilator Kit.
The lower vent of the recommended kits is provided with
proper size openings. The flow of combustion and ventilating
air must not be obstructed.
CAUTION
It is of especially importance tbat tbe airflow around
tbe burner housing, tbe boiler insulation and tbe
flow of combustion gases must not be obstructed.
Items placed in
the
vicinity of
the
refrigerator
compartment accordingly must be secured away
from the refrigerator tubing and flue.
The lower side vent is fitted with a panel, which provides an
adequate access opening for ready serviceability ofthe burner
and control manifold of the refrigerator. This should be cen-
tered on the back of the refrigerator.
'~I_-------:::=-==--_-----.JI""'"
vent cutout
28-518·
- 3 -
NDA1402
When installing the refrigerator, make sure to separate the
combustion system from the living space of the mobile home
or recreational vehicle. An opening toward the outside at floor
level in the refrigerator compartment must be provided for
ventilation of heavier- than-air fuel gases.
VENTILATION HEIGHTS
It is essential that all maximum or minimum dimensions are
strictly maintained as the performance of the refrigerator is
dependent on adequate flow of air over the rear of the refrigera-
tor. For an installation with roof vent and lower side vent, the
minimum ventilation height should be 69-1/8 inches
(1756
mm).
The upper vent should
be centered over the
condenser coil at the
back of the refrigerator.
I
I
I
I
I
I
I
I
I
I _-
",,-
.!:.-::::.-
'r-- -
I- -::::::Vf*-----i--if-
...
H
I I
I I
I I
I
Ventilation
height
CLEARANCES
Minimum clearances (in inches) to combustible materials:
Top (G)
Side (K)
Bottom (L)
o
o
o
G
OVERALL AND RECESS DIMENSIONS
..
OVERALL DIMENSIONS
Height (A) mm
1632
inches
64-17/64
Width (B) mOl
855
inches
33-11116
Depth (C) mm
752
inches
29-5/8
RECESS DIMENSIONS
Height (H) mm
1605
inches
63-3/16
Width (W) mm
832
inches
32-3/4
Depth
(D)
mm
662*
inches
26-1116*
*
Add
1" (25
mm) depth for units with one or two optional
ventilator fans.
SIDEVIEW
1
A
VIEW FROM ABOVE
c
B
- 4-
INSTALLING THE REFRIGERATOR
• Please use care when installing the refrigerator! This
refrigerator is equipped with the latest vacuum insulated
panel technology. These insulating panels are located on the
top, back, bottom, sides and doors ofthe refrigerator. If the
surface is punctured, loss of insulation will occur, resulting
in poor refrigerator performance.
• The refrigerator must be installed in a substantial enclosure
and must be level.
• Do not install the appliance directly on carpeting. Carpet-
ing must be removed or protected by a metal or wood panel
beneath the appliance, which extends at least full width and
depth of the appliance.
• Clearances: In a proper installation there should be zero
inches (0") clearance surrounding the sides, top, bottom
and rear of the refrigerator to achieve proper air flow. All
potential dead air pockets should be blocked or baffled to
ensure that heat won't be trapped in these spaces and reduce
efficiency.
All areas within the recess in which the refrigerator is
installed must be sealed. Make sure that there is a complete
seal between the front frame of the refrigerator and the top,
sides and bottom ofthe enclosure.
A length of sealing strip is applied to the rear surface of the
front frame for this purpose. The sealing should provide a
complete isolation of the appliance's combustion system
from the vehicle interior. Be careful not to damage tbe
sealing strip when the refrigerator is put in place!
• A wood strip must be in place across the upper opening
of the enclosure. The top frame ofthe refrigerator will be
anchored to the wood strip with screws.
Wood strip
SECURING THE REFRIGERATOR
It is important to follow the sequence in securing refrigerator
in enclosure since failure in doing so can cause leakage be-
tween the frame and cabinet. Any space between the counter,
storage area or ceiling and top of the refrigerator greater den
1-1/2 inches should be blocked. The heat produced at the rear
of the refrigerator will become trapped in this space, making
the top of the refrigerator hot and reduce the efficiency of the
refrigerator.
After the refrigerator is put in place (ensuring a combustion
seal at the front frame), the refrigerator is to be secured in the
enclosure with six screws (not included).
The six screws have to be installed in the following order:
~ 1.
Two screws installed througb the front base.
(Installation of the lower front strip.)
The refrigerator is provided with a lower front strip
(shipped as a loose part). Attach the front strip after
the refrigerator is set into the cutout opening.
a) Install the lower front strip by sliding it under the
bottom hinge plates.
b) Secure the refrigerator and the lower front strip
with two screws - one screw through each hinge.
2. Two screws installed in be top frame.
Open the doors and
fasten the refrigerator
with two screws through
the holes underneath the
top decoration panel.
3. Two screws installed in tbe rear base.
- 5 -
r--------------------------~------~--------------------------~~~~~
INSTALLING THE DRAIN WATER HOSE
To install the drain water hose, follow these steps:
~ 1. Drill a hole through flooring. It is essential that it is
drilled in the cut out opening of the base plate at the
rear of the refrigerator.
2. Make sure that the hose does not kink when run
through the floor.
3. Seal around the hose that goes through the drilled
hole. If a longer hose than supplied is required, the
installer needs to supply one in order for the water to
drain outside of the vehicle.
Hole for drain
waterhose
GAS CONNECTION (NDA1402)
Hook up to the gas supply line is accomplished at the manual
gas valve, which is furnished with a 3/8" SAE (UNF 5/8" -18)
male flare connection. All completed connections should be
checked for leaks with a non corrosive commercial bubble
solution.
A
WARNING
EXPLOSION HAZARD. Never use an open flame
to check for gas leaks. Failure to heed this warn-
ing could cause an explosion resulting in death or
severe personal injury.
The gas supply system must incorporate a pressure regulator
to maintain a supply pressure of not more than It inches water
column. When testing the gas supply system at test pressures:
>
112psi - the refrigerator and its individual shutoff valve
must be disconnected from the gas supply piping system.
• ~ 112psi - the appliance must be isolated from the gas
supply piping system by closing its individual manual shut-
off valve.
For detailed instructions on the installation and connection to
the gas supply, contact your dealer or distributor.
TESTING LP GAS SAFETY SHUT OFF
The gas safety shut off must be tested after the refrigerator is
connected to LP gas supply. To test the gas safety shut off, fol-
low these steps:
~ 1. Turn on the refrigerator and switch to GAS mode.
2. Check that the GAS indicator dot is illuminated and
the gas flame is lit.
3. Close the manual gas shut off valve at the back of
the refrigerator.
4. Wait for approx. 6-7 minutes. The message
"ch LP" is displayed (flashing).
5. Remove the protection cover.
6. Open the manual gas shut off valve. (Do not change
any button positions on the control panel.)
7. Apply a non corrosive commercial bubble solution
to the burner jet orifice. No bubbles should appear at
the opening of the burner jet orifice. The presence of
bubbles indicates a defective gas safety shut off, and
service is required.
8. If no bubbles were present at the burner jet orifice,
rinse it with fresh water. Be careful not to damage
the burner jet orifice.
9. Put back the cover.
10. Switch the refrigerator OFF and back ON again.
Normal operation of the burner should return.
11. Allow the burner to operate for a minimum of 5
minutes
ELECTRICAL CONNECTION
120VAC CONNECTION
The refrigerator is equipped with a three-prong (grounding)
plug for your protection against shock hazards and should be
plugged directly into a properly grounded three prong recep-
tacle. DO OT cut or remove the grounding prong from this
plug!
The free length of the cord is 2 feet and it is recommended that
the receptacle is located to the right side of the refrigerator
(viewed from the rear).
The receptacle should be 3" (from
the bottom of the plastic receptacle)
above the refrigerator mounting floor.
This allows easy access through the
vent door. The cord should be routed
to avoid direct contact with com-
ponents that could damage the cord
insulation.
120VoitAC
receptacle
3"
12V DC CONNECTION
The refrigerator requires a continuous 12 V DC supply to main-
tain the automatic energy selector system and the auto defrost
control system to function.
The connection is made to the positive (+) and negative (-)
terminals ofthe terminal block on the back of the refrigerator.
Correct polarity must be observed when connecting to the DC
supply. Do not use the chassis or vehicle frame as one of the
conductors. Connect two wires at the refrigerator and route to
the DC supply.
Maximum fuse size for the DC supply is lOA.
-6-
It is important that the wires to the 12 V DC terminal is
of proper wire size. The following table displays the recom-
mended size and length of the conductor wires.
Wire length
&
size
Length Min. size
< 33
ft
12AWG
<10m
33 - 66 ft IOAWG
]0 - 20 m
> 66
ft
8AWG
>20m
Example: If the distance between the refrigerator and the
]2V DC supply is 20
ft.,
the total wire length is 40
ft.
and
a wire size of lOAWG should be used.
MOUNTING THE DOOR PANELS
MODELS EQUIPPED WITH ICE MAKER
DOOR PANEL DIMENSIONS
Freezer door
1AAJ(1.00
,o.wc2S)
11.181
....
,
Fridge door
.,'"
...
"""'"
~~
~
51
~
1a.111
"'"
.-
~
~
~
~
~
~
i
".'"
0»,
~
t
FITTING THE DOOR PANELS
-7-
=
III
-,
1
i
FITTINGTHE DOOR PANELS
Freezer door
l
000 6
FWU
~~
~
III
Fridge door
=
III
l
000 /)
---wo
l
l
000 0
WO
••••
- 9 -
l
Model shown: NEA 1402fNDA 1402 with ice and water dispensers.
Heat.ers Flexible cord
Refrigerator
MODELS EQUIPPED WITH ICE MAKER
NEA1402
Heaters
Power module
and fuses
Protection cover
Drain water hose
Thermostat Water solenoid valve
Flexible cord Ice maker 12 Volt DC Terminal block
NDA1402
12V DC
Burner control
Protection cover
Flue baffle Power module
and fuses
Thermofuse
Flexible cord Ice maker
- 10-
MODELS EQUIPPED WITH ICE DISPENSER
NEA1402
Heaters Flexible cord
Refrigerator
Ice dispenser
power switch
Protection cove r Power module
and fuses
Thermofuse
Drain water hose
Flexible cord
Ice maker, Ice dispenser
NDA1402
--nT--re.:
---;==-::-
=--:JL=:!~lrF=--===-::r-
:::c::--~--~-;a-~-
II I
r-1\.~j~~~======~~E~II~9f;;;;;;~;;~~~
II I
l(r~~l~~======~~E~III~1~;;;;~;;~~~
II I
'~'~I~~======~~E=~llr~I~;;;;~~~~::~
II I
I
\.r:lc=====zz:;;clFlIIf--=JCtr=;=:=~=:~
,-,H~e""at~e:.!rs'--
-H-+--.JLlII
I
IL
Flexible cord
12VDC
~~~~~~;:~~~~=r:sc:~
~~:~II~ ~~~~~~~ __
R~e~f~rig=e=r=at=o=r~
Burner control I I I ~ ~
------.ur ---- ---
=:':":"=':"'::;=:'="--U~4..1
I
E ~ ~
'T-
I
P
I Ice dispenser
I
!,u
::::::r-
r- ..
power switch
I
k-Ii
0
0
r ~of".L-1'?P((((~--'Jn--.=~o
1-=----1
Power module
Flue baffle ----- ~ :
~\J
~f;> ~
IIII@ [
~===:J=='--'-~tll1l-,-a_nd_fu_se_s_
----#-l-L~--ll
I:
I---"~
@:~ ,,~.~
'r=r:~\v00 ~
IJ
T-'-'.h=er"-'-m=of=us=e'------- ~
-II ~ ~~
i!:lI
A\ ~ •• , ~ []
I ...~ II
~ ~~b )()]~..
~~~~=-'=:i:~ldJ:.
Burner jet /
1/
=
i= \ ~
Drain water hose
Manual gas shut off valve . \ Heating cable
Inlet fitting ~
Thermostat
--
Protection cover
Water hose (Ice maker)
Flexible cord
Ice maker, Ice dispenser
Water solenoid valve
12 Volt DC Terminal block
- 11 -
MODELS EQUIPPED WITH ICE AND WATER DISPENSER
NEA1402
-
--TT--'C::'- ,----
--
--
--
--
--
--
--- - r
II
~.<..
II
.l
I I
Healers I I
l
I
I
l
Flexible cord refrigeralor
I
II-
r----
~-
.J
---
~
------':":'JA
»>
~
L
I I
E
~;:J
1"1
I
P
I
I I "Dispenser power switch
I I I
L-
Pro:ection cover I I I
®
J :~
8~
I.
--
~I I I ~
I I I
if;> '--
r-
0'--
~
Power module and fuses
I I I
S
C9.,e~
or--
----
~ 0
:;~'.~~Jn*Gb
91~
1'lennofuse
II-"-.)! /.
---
®~f.£-~~ ~c
*i
j,
L
=
==-' -
rr
90· connection, water dispenser
~
,@ ~., ~ ~
••
••
-;be'Tllos:a\
12 Yolt
DCTe~;",1
block /
~ Drain water hose
J
Hose, water dispenser
Hose, icemaker
Flexible cord Heating cable
Ice maker, Ice dispense
Water solenoid valve
NDA1402
-
-- lTT--'C ,----
--
--
--
--
--
--
--- - r
II I
r--r-
l.
II I
.l.
III
Heaters II I
,l.
J-Lll.
.
11--
Flexible cord refrigerator
12VDC lil~~
..--c::L
Burner control II I
----.LA
--
..-...
itiiJ
~~71
p
I
J
Dispenser power switch
Protection cover
I
L-- __ .,
11,/1 .~
0
~~
••
e
0
=
--
~II/,I (
0
Rue baffle Ip ~ III Power module and fuses
~ C]§®~
0r--
I I I
I--
I: 11_
~
ei
~
11~
?
'fJ
"''''c
----i-h-
]I
J!;Lll-.!:l • ~
.
Thermofuse
•••
--
@
r
I~
/
'
~
=
F===V - IT
90° connection, water dispenser
,@....
'<.!!JjI"".~ •
~
r.-
~
~
••
Burner jet /
I /
~ Drain wa:er hose
","",I
9"
shut off valve
i
Inlet fitting Hose, water dispenser
Thermostat Hose, icemaker
Flexible cord
Ice maker, Ice dispenser Heating cable
Water solenoid valve
12 Volt DC Terminal block
- 12 -
The following table displays the different types of models and their corresponding wiring diagrams.
WIRING
ICE MAKER
ICE DISPENSER ICE
&
WATER DISPENSERS
DIAGRAM
NEA1402 NDA1402 NEA1402 NDA1402 NEA1402 NDA1402
385 13 24 (2)
XXX
3850699 (2)
X X
385 ]325 (2)
XXX
3850897 (3)
X X
385
11
12
X X
2
385 13 24
0=-
CIRCUIT BOARD POWER
®-
CIRCUIT BOARD DISPLAY
cv=-
12V DC BURNER CONTROL
®-
SViITCH FREEZER
~ LAMP FREEZER
®-
SViITCH FRIDGE
~ LAMP FRIDGE
®-
FAN FRIDGE
~ THERMISTOR FRIDGE AIR
®-
THERMISTOR FRIDGE FLANGE
co=-
THERMISTOR FREEZER AIR
®-
THERMISTOR FREEZER FLANGE
~ CHASSIS GROUND
®
e
t
~~~~~I~~
1 RED
..
,,"
2 BLACK
7 liED
J
RED
8 &lACK
lELLOW
8 .•.
«rn
5 SLACK
10 liED
®
fAN
+ -
12V DC
(9
N L
3A inline fuse
for the power
vent fans
®=-
ELECTRODE
®-
SOLENOID VALVE
®-::-
THERMOSTAT
®-
FAN FREEZER
cv=-
HEATING ELEMENT DRAIN TRAY
0-
HEATING ELEMENT FRIDGE
cv=-
TERMINAL BLOCK
0-
THERMOFUSE
cv=-
HEATING CABLE FRONT FRAME
@-
HEATING ELEMENT FREEZER
cv=-
PROTECTIVE EARTH
@-
HEATER 120V AC
~ ®
o
.ED
~
:~~~~
CDYEllO"
~ liED
8L"CK 1
FUSES
Fuses (from left to right) protect
the following components.
Fuse Type of component
3A A, B, C, E, G, H, P, R
7.5A S, T
3A W*
7.5A
X
5A Z
*
Optional ice maker heat-kit
- l3 -
385 06 99 2
®-=-
CIRCUIT BOARD POWER
®
ICEMAKER
®--:-
WATER VALVE
QD
HEATING CABLE
~ THERMOSTAT
Q)
CHASSIS GROUND
~ PROTECTIVE EARTH
QD
SPLICING SLEEVE
120 V AC
IN OPERATION THE ICE·MAKER
WILL ADD 1.4 AMPS TO THE
TOTAL REFRIGERATOR DRAW
;:;
0_
;:;
"
,
~
~
'
"
~
0
F~RT
0 0
®
e
.
~ ~
a
.
.
""
.
0
~ lUCk
.
~y:~~~!
e
,
:e
""
,
n,t,Ck
,
JlJ,CJ(
;;;
<
oauSE
< .<
;;;
:!!••:; ~
",
~
~
"
,
-a ,
~
00
nIT
000 000
®-
FLEX CAB LE
CD-::-
TERMINAL BLOCK
®-
WATER VALVE
~ HEATING CABLE
CD-
THERUOSTAT
cv=-
CHASSIS GROUND
CD-
PROTECTIVE EARTH
- ::=:U:
BOARD POWER
::D-
::==
T BOARD DISPLAY
""'-- 0 :-C
FREEZER
~ _' =
fREEZER
,,--; :- H FRIOGE
~ _' , FRIDGE
:- =,
fRIDGE
:::r
--"qUISTOR FRIDGE AIR
~- --",UISTOR FRIDGE FLANGE
&
--=qUISTOR FREEZER AIR
~- --" UISTOR FREEZER FLANGE
o
<
< . <
~the power vent fans
'O'fiR
>onR
SWITCH
®
"'" ::E ::,,-- <31
f'EATING
?
Z- ~~~~~~:-:~
COJfTROl
:;:- ::E ::,,;:IS3I
GHT
CABLE
BOARE
- 14-
®-::--
CHASS I S GROUND
®-
FAN FREEZER
cv-=-
HEATING ELEMENT DRAIN TRAY
®-
HEATING ELEMENT FRIDGE
~ TERMINAL BLOCK
®-
THERMO FUSE
cv=-
HEATING CABLE FRONT FRAME
@-
HEATING ELE~IENT FREEZER
cv=-
THERMOSTAT
0-
PROTECTIVE EARTH
CD=-
HEATER 120V AC
CD
CD-:-
BLACK
CD-
BROWN
CD::-
RED
0-
YELLOW
~GREEN
®-
GREEN/YELLOW
c:v-=--
B L U E
CD-
GREY
@-=-WHITE
120 V
AC
IN OPERATION THE ICE MAKER
AND ICE DISPENSER WILL ADD
4,5
A TO THE TOTAL
REFRIGERATOR DRAWl
FUSES
Fuses (from left to right) protect
the following components.
Fuse Type of component
3A A, B, D, F, G, N
7.5A
O,P
3A T*
7.5A U
5A Z
*
Optional ice maker heat-kit
r
385 11 12
F=-,:=====---------j?'-3
Pl·"
r
-t--t============1
P1'1
P'-2
,
m
"""l
·
JUU
P2
,
.un
PO
HUE
/lUT
3
t
m
'~n
4
,
...
·
.u.tI:
TELL~'
·
•un
~ IIl~~~
.
,
nAtI(
0
,
"
'"
~,~~~!:
s
,
::5l:~~
.
,
·
:; :;
,
IlA"
·
O~"'UE
< -<
::;
,
::~''I:;~
~.~
~
=~=
~
·
~
",
00 000 000
IN OPERA nON THE ICE MAKER
AND ICE DISPENSER WILL ADD
4,5 A TO THE TOTAL
REFRIGERATOR ORAW!
120 V AC
CD:-
BLACK
CD-
BROWN
®::---
RED
0-
YELLO\!
®-:=-
GREEN
CD- GREEN/YELLOW
CD::-
BLUE
CD-GREY
®-=--
WHITE
0::-
CIRCUIT BOARO POWER
CD- ICE DISPENSER POWER SWITCH
~ FUSE SA
®-
ICE ~AKER
®
cv=-
AUGER
CD-
CRUSCH
®-::-
ICE DISPENSER HEATING CABLE
®-
ICE DISPENSER
c:D-=:---
ICE DISPENSER CONTROL BOARE
0-
ICE DISPENSER LIGHT
®-
FLEX CABLE
~ TERUINAL BLOCK
®-
WATER VALVE
~ HEATING CABLE
®-
THERMOSTAT
cu=--
CHASS IS GROUND
®-
PROTECTIVE EARTH
- 15 -
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15

Dometic NDA1402 Installation guide

Type
Installation guide
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI