Dometic Refrigerator NEA1402_NDA1402 Installation guide

Dometic
Brand
Dometic
Model
Refrigerator NEA1402_NDA1402
Category
Fridges
Type
Installation guide
NEA1402
NDA1402
autodefrost
INSTALLATION
MANUAL
MO 0938
825125902
©2006-2009, LLC
LaGrange, IN 46761
USA Corporate Ofce CANADA
Service Ofce 2320 Industrial Parkway Elkhart, IN 46516 Dometic, LLC
Dometic, LLC 46 Zatonski, Unit 3
2320 Industrial Pkwy. Brantford, ON, N3T 5L8
Elkhart, IN 46516 For Service Center Assistance CANADA
Phone: 574-294-2511 Call: 800-544-4881 Phone: 519-720-9578
FOR YOUR SAFETY
If you smell gas:
1. Open windows.
2. Don’t touch electrical switches.
3. Extinguish any open ame.
4. Immediately call your gas supplier.
POUR VOTRE SÉCURITÉ
Si vous sentez une odeur de gaz:
1. Ouvrez les fenêtres.
2. Ne touchez à aucun interrupteur.
3. Éteignez toute amme nue.
4. Avertissez immédiatement votre
fournisseur de gaz.
FOR YOUR SAFETY
Do not store or use gasoline or other
ammable vapors and liquids in the
vicinity of this or any other appliance.
POUR VOTRE SÉCURITÉ
Ne pas entreposer ni utiliser de l’essence
ni d’autres vapeurs ou liquides inamma-
bles à proximité de cet appareil ou de tout
autre appareil.
Improper installation, adjustment,
alteration, service or maintenance can
cause injury or property damage. Refer to
this manual. For assistance or additional
information consult a qualied installer,
service agency or the gas supplier.
Une installation, un réglage, une modi-
cation, une réparation ou un entretien non
conforme aux normes peut entraîner des
blessures ou des dommages matériels.
Lisez attentivement le mode d’emploi
fourni avec l’appareil. Pour obtenir de
l’aide ou des renseignements supplémen-
taires, consultez un installateur ou un
service d’entretien qualié ou le fournis-
seur de gaz.
warning avertissement
6
!6
!
If the refrigerator stops cooling - or - if
ammonia emanates from it, immediately
turn the refrigerator off and contact a
Service Center.
Si le réfrigérateur cesse de refroidir - ou - si
de l’ammoniac s’en dégage, arrêtez immé-
diatement le réfrigérateur et contactez un
centre de réparation.
warning avertissement
6
!6
!
- 2 -
contents
This product is manufactured under
license of U.S. Patent Number 6.019,447.
Patents pending
U.S. 10/619,675
U.S. 10/620,177
U.S. 10/758,174
U.S. 10/758,175
U.S. 10/760,564
U.S. 10/760,565
symbols
The following symbols are used throughout the manual:
Indicates a potentially hazardous situation, which, if not avoided, could result
in death or serious injury.
Indicates a potentially hazardous situation, which, if not avoided, may result in
minor or moderate injury.
Used without the safety alert symbol indicates, a potentially hazardous situation which, if not avoided
may result in property damage.
Information
Step-by-step instructions
CAUTION
!
WARNING
!
CAUTION
introduction. 3
certification.and.code.requirements .                                     3
ventilation.requirements. 3
installation.procedure. 5
appendix.a.-.rearview.equipment.......................................... 10
appendix.B.-.wiring.diagrams. 13
- 3 -
ventilation requirements
introduction
certification and code requirements
This manual describes how to install NEA1402 (all-electric operation) and NDA1402 (2-way operation). These models can be
equipped with an ice maker, an ice dispenser or ice & water dispensers.
The information in this manual is intended for qualied technicians with knowledge and experience of absorption refrigerators
and LP gas systems. For operating instructions, please refer to the User manual for the appliance in question.
Read this manual before installing the refrigerator. Comply with installation specications and dimensions. Follow the instructions
to ensure that the refrigerator is installed safely and that it runs efciently. Be aware of possible safety hazards when seeing alert
symbols on the refrigerator as well as in this manual.
general information
Provide necessary air circulation over the cooling unit. Open-
ings for air supply or for venting of combustion products shall
have a minimum dimension of not less than 1/4 inch.
Certied installations require one roof vent and one lower side
vent. Proper installation requires one lower fresh air intake
and one upper exhaust vent. The ventilation kits shown in this
manual have been certied for use with NEA1402 and
NDA1402. The ventilation kits must be installed and used
without modication.

  
5A Roof Base
Roof Cover
Lower Side Vent
Power Vent Asm.
3103633.XXX*
3103634.XXX*
3109349.XXX*
3108705.744**
* Fill in “XXX” with color code numbers. For color codes, contact
your supplier.
** Alternate instructions forwarded with the Ventilator Kit.
The appliance is certied under the latest edition of ANSI Z21.19•CSA 1.4 Refrigerators using gas fuel. The installation must
conform with local codes, or in absence of local codes, the following standards as applicable.
In the U.S. the installation must conform with:
National Fuel Gas Code, ANSI Z223.1/NFPA 54 (latest edi-•
tion).
Recreational Vehicles Code, ANSI A119.2 (latest edition)•
Manufactured Home Construction and Safety Standard, Title •
24 CFR, Part 3280.
If an external electrical source is utilized, the refrigerator, when
installed, must be electrically grounded in accordance with lo-
cal codes or, in the absence of local codes, the National Electri-
cal Code, ANSI/NFPA 70 - (latest edition).
In CANADA, the installation must conform with:
Natural Gas and Propane Installation Code, CSA B149.1•
CSA Z240 RV Series, Recreational Vehicles.•
Current CSA Z240.4, Gas-equipped Recreational Vehicles •
and Mobile Housing.
If an external electrical source is utilized, the refrigerator,
when installed, must be electrically grounded in accordance
with local codes or, in the absence of local codes, the Canadian
Electrical Code, CSA C22.1, Parts I and II - (latest edition).

LOWER VENT CUTOUT
13-5/8”
28-5/8”
CAUTION
It is of especially importance that the airow around
the burner housing, the boiler insulation and the
ow of combustion gases must not be obstructed.
Items placed in the vicinity of the refrigerator
compartment accordingly must be secured away
from the refrigerator tubing and ue.
The lower vent of the recommended kits is provided with
proper size openings. The ow of combustion and ventilating
air must not be obstructed.
The lower side vent is tted with a panel, which provides an
adequate access opening for ready serviceability of the burner
and control manifold of the refrigerator. This should be cen-
tered on the back of the refrigerator.
- 4 -
clearances
Minimum clearances (in inches) to combustible materials:
Top (G) 0
Side (K) 0
Bottom (L) 0
G
KK
L
ventilation requirements
nda1402
When installing the refrigerator, make sure to separate the
combustion system from the living space of the mobile home
or recreational vehicle. An opening toward the outside at oor
level in the refrigerator compartment must be provided for
ventilation of heavier-than-air fuel gases.
ventilation heights
It is essential that all maximum or minimum dimensions are
strictly maintained as the performance of the refrigerator is
dependent on adequate ow of air over the rear of the refrigera-
tor. For an installation with roof vent and lower side vent, the
minimum ventilation height should be 69-1/8 inches
(1756 mm).
Ventilation
height
Condenser
The upper vent should
be centered over the
condenser coil at the
back of the refrigerator.
OVERALL DIMENSIONS
Height (A) mm 1632
inches 64-17/64
Width (B) mm 855
inches 33-11/16
Depth (C) mm 752
inches 29-5/8
RECESS DIMENSIONS
Height (H) mm 1605
inches 63-3/16
Width (W) mm 832
inches 32-3/4
Depth (D) mm 662*
inches 26-1/16*
* Add 1" (25 mm) depth for units with one or two optional
ventilator fans.
D
W
C
B
view.from.aBove
D
H A
side.view
overall and recess dimensions
- 5 -
installation procedure
installing the refrigerator
Please use care when installing the refrigerator! This •
refrigerator is equipped with the latest vacuum insulated
panel technology. These insulating panels are located on the
top, back, bottom, sides and doors of the refrigerator. If the
surface is punctured, loss of insulation will occur, resulting
in poor refrigerator performance.
The refrigerator must be installed in a substantial enclosure •
and must be level.
Do not install the appliance directly on carpeting. Carpet-•
ing must be removed or protected by a metal or wood panel
beneath the appliance, which extends at least full width and
depth of the appliance.
Clearances: In a proper installation there should be zero •
inches (0”) clearance surrounding the sides, top, bottom
and rear of the refrigerator to achieve proper air ow. All
potential dead air pockets should be blocked or bafed to
ensure that heat won’t be trapped in these spaces and reduce
efciency.
All areas within the recess in which the refrigerator is •
installed must be sealed. Make sure that there is a complete
seal between the front frame of the refrigerator and the top,
sides and bottom of the enclosure.
A length of sealing strip is applied to the rear surface of the
front frame for this purpose. The sealing should provide a
complete isolation of the appliance’s combustion system
from the vehicle interior. Be careful not to damage the
sealing strip when the refrigerator is put in place!
securing the refrigerator
It is important to follow the sequence in securing refrigerator
in enclosure since failure in doing so can cause leakage be-
tween the frame and cabinet. Any space between the counter,
storage area or ceiling and top of the refrigerator greater den
1-1/2 inches should be blocked. The heat produced at the rear
of the refrigerator will become trapped in this space, making
the top of the refrigerator hot and reduce the efciency of the
refrigerator.
After the refrigerator is put in place (ensuring a combustion
seal at the front frame), the refrigerator is to be secured in the
enclosure with six screws (not included).
The six screws have to be installed in the following order:
Two screws installed through the front base. 1.
(Installation of the lower front strip.)
The refrigerator is provided with a lower front strip
(shipped as a loose part). Attach the front strip after
the refrigerator is set into the cutout opening.
Install the lower front strip by sliding it under the a)
bottom hinge plates.
Secure the refrigerator and the lower front strip b)
with two screws - one screw through each hinge.
Two screws installed in he top frame. 2.
Open the doors and
fasten the refrigerator
with two screws through
the holes underneath the
top decoration panel.
Two screws installed in the rear base.3.
A wood strip must be in place across the upper opening •
of the enclosure. The top frame of the refrigerator will be
anchored to the wood strip with screws.
- 6 -
installation procedure
gas connection (nda1402)
Hook up to the gas supply line is accomplished at the manual
gas valve, which is furnished with a 3/8” SAE (UNF 5/8” -18)
male are connection. All completed connections should be
checked for leaks with a non corrosive commercial bubble
solution.
The gas supply system must incorporate a pressure regulator
to maintain a supply pressure of not more than 11 inches water
column. When testing the gas supply system at test pressures:
> 1/2 psi• - the refrigerator and its individual shutoff valve
must be disconnected from the gas supply piping system.
≤ • 1/2 psi - the appliance must be isolated from the gas
supply piping system by closing its individual manual shut-
off valve.
For detailed instructions on the installation and connection to
the gas supply, contact your dealer or distributor.
installing the drain water hose
To install the drain water hose, follow these steps:
Drill a hole through ooring. It is essential that it is 1.
drilled in the cut out opening of the base plate at the
rear of the refrigerator.
Make sure that the hose does not kink when run 2.
through the oor.
Seal around the hose that goes through the drilled 3.
hole. If a longer hose than supplied is required, the
installer needs to supply one in order for the water to
drain outside of the vehicle.
testing lp gas safety shut off
The gas safety shut off must be tested after the refrigerator is
connected to LP gas supply. To test the gas safety shut off, fol-
low these steps:
Turn on the refrigerator and switch to GAS mode.1.
Check that the GAS indicator dot is illuminated and 2.
the gas ame is lit.
Close the manual gas shut off valve at the back of 3.
the refrigerator.
Hole for drain
water hose
WARNING
EXPLOSION HAZARD. Never use an open ame
to check for gas leaks. Failure to heed this warn-
ing could cause an explosion resulting in death or
severe personal injury.
6
!
electrical connection
120 v ac connection
The refrigerator is equipped with a three-prong (grounding)
plug for your protection against shock hazards and should be
plugged directly into a properly grounded three prong recep-
tacle. DO NOT cut or remove the grounding prong from this
plug!
The free length of the cord is 2 feet and it is recommended that
the receptacle is located to the right side of the refrigerator
(viewed from the rear).
The receptacle should be 3” (from
the bottom of the plastic receptacle)
above the refrigerator mounting oor.
This allows easy access through the
vent door. The cord should be routed
to avoid direct contact with com-
ponents that could damage the cord
insulation.
120 Volt AC
receptacle
3 ’’
12 v dc connection
The refrigerator requires a continuous 12 V DC supply to main-
tain the automatic energy selector system and the auto defrost
control system to function.
The connection is made to the positive (+) and negative (-)
terminals of the terminal block on the back of the refrigerator.
Correct polarity must be observed when connecting to the DC
supply. Do not use the chassis or vehicle frame as one of the
conductors. Connect two wires at the refrigerator and route to
the DC supply.
Maximum fuse size for the DC supply is 10 A.
Wait for approx. 6-7 minutes. The message 4.
“ch LP” is displayed (ashing).
Remove the protection cover. 5.
Open the manual gas shut off valve. (Do not change 6.
any button positions on the control panel.)
Apply a non corrosive commercial bubble solution 7.
to the burner jet orice. No bubbles should appear at
the opening of the burner jet orice. The presence of
bubbles indicates a defective gas safety shut off, and
service is required.
If no bubbles were present at the burner jet orice, 8.
rinse it with fresh water. Be careful not to damage
the burner jet orice.
Put back the cover.9.
Switch the refrigerator OFF and back ON again. 10.
Normal operation of the burner should return.
Allow the burner to operate for a minimum of 5 11.
minutes
- 7 -
fitting.the.door.panels
models equipped with ice maker
Freezer door Refrigerator door
11.181
(284)
15.237
(387)
)5.196( 422.72
))5.497( 972.13(
˚54
)5.7( 592.
)0251( 248.95
493.
791. +
890. – 01(
5+
)5.2–
.197(2x) (5)(2x)
MAX 1.00
(MAX 25) MAX 1.00
(MAX 25)
)5.7( 592.
˚54
.197 (2x) (5)(2x)
493.
791. +
890. – 01(
5+
)5.2–
16.811
(427)
12.756
(324)
)5.217( 150.82
))5.518( 601.23(
)0251( 248.95
Freezer door Refrigerator door
11.181
(284)
15.237
(387)
)5.196( 422.72
))5.497( 972.13(
˚54
)5.7( 592.
)0251( 248.95
493.
791. +
890. – 01(
5+
)5.2–
.197(2x) (5)(2x)
MAX 1.00
(MAX 25) MAX 1.00
(MAX 25)
)5.7( 592.
˚54
.197 (2x) (5)(2x)
493.
791. +
890. – 01(
5+
)5.2–
16.811
(427)
12.756
(324)
)5.217( 150.82
))5.518( 601.23(
)0251( 248.95
door.panel.dimensions
installation procedure
mounting the door panels
Freezer door
Fridge door
It is important that the wires to the 12 V DC terminal is
of proper wire size. The following table displays the recom-
mended size and length of the conductor wires.

Length Min. size
< 33 ft
< 10 m
12 AWG
33 - 66 ft
10 - 20 m
10 AWG
> 66 ft
> 20 m
8 AWG
Example: If the distance between the refrigerator and the
12V DC supply is 20 ft., the total wire length is 40 ft. and
a wire size of 10 AWG should be used.
- 8 -
installation procedure
Freezer door Refrigerator door
11.181
(284)
15.237
(387)
)5.196( 422.72
˚54
)5.7( 592. 493.
791. +
890. – 01(
5+
)5.2–
.197(2x) (5)(2x)
MAX 1.00
(MAX 25)
MAX 1.00
(MAX 25)
)5.7( 592.
˚54
.197 (2x) (5)(2x)
493.
791. +
890. – 01(
5+
)5.2–
16.811
(427)
12.756
(324)
)5.217( 150.82
))5.518( 601.23(
)0251( 248.95
)5.7( 592.
)083( 069.41
.197(2x) (5)(2x)
MAX 1.00
(MAX 25)
493.
791. +
890. – 01(
5+
)5.2–
.913 (23.2) 9.370 (238)
)067( 129.92
Freezer door Refrigerator door
11.181
(284)
15.237
(387)
)5.196( 422.72
˚54
)5.7( 592. 493.
791. +
890. – 01(
5+
)5.2–
.197(2x) (5)(2x)
MAX 1.00
(MAX 25)
MAX 1.00
(MAX 25)
)5.7( 592.
˚54
.197 (2x) (5)(2x)
493.
791. +
890. – 01(
5+
)5.2–
16.811
(427)
12.756
(324)
)5.217( 150.82
))5.518( 601.23(
)0251( 248.95
)5.7( 592.
)083( 069.41
.197(2x) (5)(2x)
MAX 1.00
(MAX 25)
493.
791. +
890. – 01(
5+
)5.2–
.913 (23.2) 9.370 (238)
)067( 129.92
Freezer door Refrigerator door
11.181
(284)
15.237
(387)
)5.196( 422.72
˚54
)5.7( 592. 493.
791. +
890. – 01(
5+
)5.2–
.197(2x) (5)(2x)
MAX 1.00
(MAX 25)
MAX 1.00
(MAX 25)
)5.7( 592.
˚54
.197 (2x) (5)(2x)
493.
791. +
890. – 01(
5+
)5.2–
16.811
(427)
12.756
(324)
)5.217( 150.82
))5.518( 601.23(
)0251( 248.95
)5.7( 592.
)083( 069.41
.197(2x) (5)(2x)
MAX 1.00
(MAX 25)
493.
791. +
890. – 01(
5+
)5.2–
.913 (23.2) 9.370 (238)
)067( 129.92
models equipped with ice dispenser / ice & water dispensers
door.panel.dimensions
Freezer door Fridge door
- 9 -
installation procedure
Freezer door
Refrigerator door
Freezer door
Refrigerator door
Model shown: NEA1402/NDA1402 with ice and water dispensers.
fitting.the.door.panels
Freezer door
Fridge door
- 10 -
appendix a - rearview equipment

12V DC
12V DC
Heaters
12V DC
Burner control
Protection cover
Flue baffle
Thermofuse
Burner jet
Inlet fitting
Thermostat
Manual gas shut off valve
Flexible cord Ice maker 12 Volt DC Terminal block
Heating cable
Drain water hose
Water solenoid valve
Water hose (Ice maker)
Flexible cord
Refrigerator
Power module
and fuses
nda1402
nea1402
Thermostat
12V DC
12V DC
Heaters
Protection cover
Thermofuse
Water hose icemaker
Heating cable
12 Volt DC Terminal block
Water solenoid valve
Drain water hose
Power module
and fuses
Flexible cord
Refrigerator
Flexible cord Ice maker
- 11 -
appendix a - rearview equipment

Heaters
12V DC
Burner control
Protection cover
Flue baffle
Thermofuse
Burner jet
Manual gas shut off valve
Inlet fitting
Thermostat
Flexible cord
Ice maker, Ice dispenser
12V DC
12V DC
Water solenoid valve
Water hose (Ice maker)
Heating cable
Drain water hose
12 Volt DC Terminal block
Flexible cord
Refrigerator
Ice dispenser
power switch
Power module
and fuses
12V DC
12V DC
Heaters
Protection cover
Thermofuse
Thermostat
Drain water hose
12 Volt DC Terminal block
Water hose icemaker
Heating cable
Water solenoid valve
Flexible cord
Ice maker, Ice dispenser
Flexible cord
Refrigerator
Ice dispenser
power switch
Power module
and fuses
nda1402
nea1402
- 12 -
appendix a - rearview equipment

12V DC
Heaters
Protection cover
Thermofuse
Thermostat
Drain water hose
12 Volt DC Terminal block
Hose, icemaker
Hose, water dispenser
Heating cable
Water solenoid valve
Flexible cord
Ice maker, Ice dispenser
Flexible cord refrigerator
Dispenser power switch
Power module and fuses
90° connection, water dispenser
Heaters
12V DC
Burner control
Protection cover
Flue baffle
Thermofuse
Burner jet
Manual gas shut off valve
Inlet fitting
Thermostat
Flexible cord
Ice maker, Ice dispenser
12V DC
12V DC
12 Volt DC Terminal block
Drain water hose
Hose, icemaker
Hose, water dispenser
Heating cable
Water solenoid valve
Flexible cord refrigerator
Dispenser power switch
Power module and fuses
90° connection, water dispenser
nda1402
nea1402
- 13 -
appendix b - wiring diagrams
6
7
8
9
1 0
5
4
3
2
1
BLACK
YELLOW
RED
BLACK
RED
BLACK
RED
BLACK
WHITE
RED
BROWN
GREEN
BLACK
RED
2
4
6
5
3
1
1234 4
3
2
1
BLUE
YELLOW
GREY
2
4
3
1
6
5
4
1
2
3
RED
WHITE
RED
BLACK
YELLOW
BLACK
J
K
L
M
F
D
E
H
G
1
3
4
2
GREY
WHITE
YELLOW
BLUE
R
DISPLAY
1 2
WHITE
YELLOW
J 1
J 2
J 3
J 4
J 5
J 6
J 7
J 8
J 9
J 1 0
J 1 1
TEST
PORT
3 A
7 . 5 A
5 A
7 . 5 A
3 A
Z
+−
12V DC
BLACK
RED
WHITE
WHITE
BLACK
RED
BLACK
BLACK
LN
Y
A
B
C
D
E
F
G
SWITCH FREEZER
12V DC BURNER CONTROL
LAMP FRIDGE
L
K
FAN FRIDGE
SWITCH FRIDGE
M
P
O
SOLENOID VALVE
Q
FAN FREEZER
ELECTRODE
THERMISTOR FREEZER FLANGE
CIRCUIT BOARD POWER
R
THERMISTOR FRIDGE FLANGE
THERMOSTAT
H
CIRCUIT BOARD DISPLAY
LAMP FREEZER
THERMISTOR FREEZER AIR
JTHERMISTOR FRIDGE AIR
HEATING ELEMENT DRAIN TRAY
THEATING ELEMENT FRIDGE
S
U
THERMOFUSEV
TERMINAL BLOCK
HEATING CABLE FRONT FRAME
XHEATING ELEMENT FREEZER
W
Y
HEATER 120V ACZ
PROTECTIVE EARTH
S T
N
N
X
W
U
BLACK
RED
V
B
GREY
BLACK
WHITE
OP
C
A
P 3 P2 BLUE
P5 BLUE
BLACK
ORANGE
385 13 24
FAN
°
C
Q
FAN
RED
RED
RED
RED
BLACK
BLACK
NCHASSIS GROUND
3 A
2
fuses
Fuses (from left to right) protect
the following components.
 
3A A, B, C, E, G, H, P, R
7.5A S, T
3A W*
7.5A X
5A Z
* Optional ice maker heat-kit


  
NEA1402 NDA1402 NEA1402 NDA1402 NEA1402 NDA1402
385 13 24 (2) X X X
385 06 99 (2) X X
385 13 25 (2) X X X
385 08 97 (3) X X
385 11 12 X X
The following table displays the different types of models and their corresponding wiring diagrams.
3A inline fuse
for the power
vent fans
- 14 -
appendix b - wiring diagrams
6
7
8
9
1 0
5
4
3
2
1
BLACK
YELLOW
RED
BLACK
RED
BLACK
RED
BLACK
WHITE
RED
BROWN
GREEN
BLACK
RED
2
4
6
5
3
1
1234 4
3
2
1
2
4
3
1
6
5
4
1
2
3
RED
WHITE
RED
BLACK
YELLOW
BLACK
H
J
K
L
E
C
D
G
F
N
DISPLAY
J 1
J 2
J 3
J 4
J 5
J 6
J 7
J 8
J 9
J 1 0
J 1 1
TEST
PORT
3 A
7 . 5 A
5 A
7 . 5 A
3 A
Z
+−
12V DC
BLACK
RED
WHITE
WHITE
BLACK
RED
BLACK
BLACK
LN
X
A
B
C
D
E
F
G
SWITCH FREEZER
LAMP FRIDGE
L
K
FAN FRIDGE
SWITCH FRIDGE
N
M
FAN FREEZER
O
HEATING ELEMENT FRIDGE
CHASSIS GROUND
THERMISTOR FREEZER FLANGE
CIRCUIT BOARD POWER
P
THERMISTOR FRIDGE FLANGE
HEATING ELEMENT DRAIN TRAY
H
CIRCUIT BOARD DISPLAY
LAMP FREEZER
THERMISTOR FREEZER AIR
J
THERMISTOR FRIDGE AIR
TERMINAL BLOCK
STHERMOFUSE
R
T
HEATING ELEMENT FREEZERU
HEATING CABLE FRONT FRAME
THERMOSTAT
XPROTECTIVE EARTH
V
O P
M
U
T
R
BLACK
RED
S
B
BLACK
WHITE
A
P 3 P2 BLUE
P5 BLUE
BLACK
ORANGE
385 13 25
FAN
°
C
V
FAN
RED
RED
RED
RED
BLACK
BLACK
ZHEATER 120V AC
3 A
2
fuses
Fuses (from left to right) protect
the following components.
 
3A A, B, D, F, G, N
7.5A O, P
3A T*
7.5A U
5A Z
* Optional ice maker heat-kit
3A inline fuse for the power vent fans
- 15 -
appendix b - wiring diagrams
TO THE INSTALLER
PLEASE AFFIX THESE INSTRUCTIONS
TO THE REFRIGERATOR
—
TO THE CONSUMER
PLEASE RETAIN THESE INSTRUCTIONS
FOR FUTURE REFERENCE
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

Dometic Refrigerator NEA1402_NDA1402 Installation guide

Dometic
Brand
Dometic
Model
Refrigerator NEA1402_NDA1402
Category
Fridges
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents