Leviton R08BD-208 Owner's manual

Programming Guide

EZ-MAX PLUS™ RELAY PRODUCTS

Covering EZ-Maz Plus Relay Panels

Software Revision 1.0 and above.

WEB VERSION

i

Table of Contents

Overview

Introduction.......................................................................................................... 1

Product Specifications and Capabilities.................................................................... 1

EZ-Max Plus—Stand Alone Panels...................................................................... 1

Product Specifications and Capabilities Chart...................................................... 2

EZ-MAX Plus User Interface

Front Panel Display................................................................................................ 3

Programming/Function Buttons ......................................................................... 4

Menu Structure ..................................................................................................... 4

Deciphering the LCD Display Elements............................................................... 4

Navigation Buttons........................................................................................... 6

Auto-Repeat................................................................................................ 6

LED’s.................................................................................................................... 6

System Status LED’s......................................................................................... 6

Relay Status LED’s............................................................................................ 8

Internal Relay Cabinet Controls .............................................................................. 8

Master Override .................................................................................................... 9

Individual Relay Overrides.....................................................................................10

Temporarily Overriding a Relay ........................................................................11

Locking out a Relay using its Override Button....................................................11

Unlocking a Relay Using its Override Button:.....................................................12

Setting the Time, Date, and Astronomical Time Clock

Menu Overview....................................................................................................13

Setting the Time ..................................................................................................13

Setting the Date...................................................................................................15

Setting the Astronomical Time Clock......................................................................15

Setting the Astro Clock by City .........................................................................16

Setting the Astro Clock by Longitude and Latitude .............................................16

Configuring System Settings

Menu Overview....................................................................................................19

Relays .................................................................................................................19

Supported Relay Types....................................................................................20

Basic Relay Configuration.................................................................................20

Relay Response to a Blink Warn Message..........................................................20

Relay Response to an Emergency Signal ...........................................................20

Set All Relays..................................................................................................21

Configuring Individual Relays ...........................................................................22

WEB VERSION

ii

Global Timers.......................................................................................................23

Blink Warn Parameters ....................................................................................23

Example Blink Warn Scenario...........................................................................23

Momentary Timed interval ...............................................................................23

Configuring Global Timers Settings...................................................................24

Security...............................................................................................................25

Disabling the Passcode ....................................................................................25

Changing your Passcode..................................................................................25

Factory Default Settings........................................................................................26

Saving and Restoring Configuration..................................................................26

The Scheduler

Basic Concepts.....................................................................................................27

Days of the Week............................................................................................27

Event Times....................................................................................................28

Holiday Mode..................................................................................................28

Common North American Holidays...............................................................28

Creating a New Event...........................................................................................29

Changing an Event Time.......................................................................................31

Deleting an Event.................................................................................................31

Editing an Event...................................................................................................32

Configuring Low Voltage Inputs

Low Voltage Inputs ..............................................................................................35

Low Voltage Switches...........................................................................................35

Low Voltage Switch Inputs...............................................................................35

Configuring a Low Voltage Switch.....................................................................36

Occupancy Sensors ..............................................................................................37

Configuring Occupancy Sensors........................................................................37

Photocells............................................................................................................39

Daylight Harvesting.........................................................................................39

Configuring Photocells.....................................................................................40

Digital Switches

Configuring A Digital Switch..................................................................................43

Manual and Auto-Assign ..................................................................................43

Determining the State of a Digital Switch..........................................................44

Unconfiguring a Digital Switch Button....................................................................45

Table of Binary Addresses.....................................................................................46

WEB VERSION

iii

Updating Firmware

Installing Updates ................................................................................................49

Terminal Settings ............................................................................................49

Configuring the Terminal Program....................................................................50

Upgrading your EZ-Max Plus Cabinet Firmware..................................................51

Viewing All Tera Term Commands ....................................................................56

Verifying your Upgrade.........................................................................................56

Appendix A: Longitude/Latitude and City Code Reference

Quick-Codes for 101 Major Cities......................................................................... A-1

Longitude and Latitude of Major Cities................................................................. A-2

Appendix B: Menus

Set Time/Date, Astro Clock ................................................................................. B-1

Scheduler .......................................................................................................... B-2

System Settings ................................................................................................. B-3

Configuring Inputs.............................................................................................. B-4

WEB VERSION

iv

WEB VERSION

EZ-Max Plus Programming Guide Page 1

Overview

Introduction

The EZ-MAX Plus product line offers a scalable time-clock solution of relay and relay

controls that can fit any application.

This manual is designed to assist you in the programming of your relay cabinet. It

assumes you have already installed the relay cabinet. See the EZ-MAX Plus

Installation Guide for detailed installation instructions.

The following resources are also available to you:

• Quick Start Programming Guide (included with every panel).

• Programming Guide (included with every panel).

• Additional resources located at our website at http://www.leviton.com/lms.

The Quick Picks drop down menu near the bottom of the page contains links to

documentation and software updates.

A hard copy of the Programmer’s Guide is included with your system purchase. Please

contact Leviton Technical Support at (800)959-6004 to request additional copies.

Product Specifications and Capabilities

The specifications and capabilities for each product are shown in the “EZ-MAX Plus

Product Capabilities Chart” on page 2.

EZ-Max Plus—Stand Alone Panels

EZ-Max Plus relay panels offer the most commonly used feature set of the Z-MAX Plus

product line family, including networking functionality and modular relays. Relay panel

sizes range from 8 to 24 relays per panel.

Leviton recommends that you check our website

regularly for important product updates.

http://www.leviton.com/lms

WEB VERSION

2YHUYLHZ 3URGXFW6SHFLILFDWLRQVDQG&DSDELOLWLHV

3URGXFW6SHFLILFDWLRQVDQG&DSDELOLWLHV&KDUW

7KHWDEOHEHORZJLYHVDJHQHUDORYHUYLHZRIWKHVSHFLILFDWLRQVRIDOO(=0D[3OXVUHOD\

SURGXFWV7KHWDEOHXVHVWKHIROORZLQJDEEUHYLDWLRQV

< <HV

1 1R

2 2SWLRQDO

 $VLQJOH DVWHULVNLQDQ\FROXPQLQGLFDWHVWKDWWKHUHLV VXSSRUW IRUWKLVIHDWXUH

KRZHYHU WKHUH DUH FRQGLWLRQV WKDW \RX VKRXOG EH DZDUH RI &RQVXOW WKH VSHFLILF

VHFWLRQV RI WKH PDQXDO GHDOLQJ ZLWK WKLV IHDWXUH IRU DGGLWLRQDO LQIRUPDWLRQ DQG

UHTXLUHPHQWV

3DJH

)LJXUH (=0$;3OXV3URGXFW&DSDELOLWLHV&KDUW

(=0D[3OXV

3URGXFW7\SH

0LQ0D[5HOD\V

5HOD\7\SHV

:HLJKWOEV.J

6L]H

:+'

:FP+FP'FP

)OXVK0RXQW2SWLRQ

'LVFUHHW,QSXWV

6Z,QSXW%RDUG$YDL

/XPD1HW1HWZRUN

'0;1HWZRUN

0DVWHU6ODYH1HW

(PHUJHQF\,QSXW

(PHUJHQF\2XWSXW

7RXFK7RQH3KRQH

'DWD0RGHP

(WKHUQHW1HWZRUN

)URQW3DQHO3URJUDP

(YHQW6FKHGXOHU

0DVWHU3DQHO

UHOD\V

  



[[

[[

<1<11<<221<<

0DVWHU3DQHO

UHOD\V

  



[[

[[

<<<11<<221<<

0DVWHU3DQHO

UHOD\V

  



[[

[[

<<<11<<221<<

1RWH9ROWDJHYY#$Y#$

5HOD\7\SHV$/DWFKLQJ3ROH3ROHRSWLRQDO

WEB VERSION

EZ-Max Plus Programming Guide Page 3

EZ-MAX Plus User Interface

Your relay panel has many unique operational features which can be accessed directly

from the front panel, including relay control, relay overrides, and basic status

information. You will also find several “status” indicators (LED’s) inside the relay panel

as well as on the outside of the panel. These LED’s indicate how your panel is

operating and whether or not it is operating properly.

Front Panel Display

This section covers the basic functions of the front panel display. The following

sections cover specifics on how to use the front panel to program and configure your

relay cabinet.

Figure 2: EZ-MAX Plus LCD Display

WEB VERSION

EZ-MAX Plus User Interface Menu Structure

Page 4

Programming/Function Buttons

The main buttons you will use to program the functionality of your cabinet are listed

below.

• MENU—displays the main menu.

• SELECT/SAVE—moves you through the menu tree, and saves any changes.

• CANCEL—returns to the previous menu.

• CLEAR—clears the text or value that was just entered.

• RELAY ON/OFF—button that allows a user to turn a relay ON or OFF, or execute

a permanent relay override.

• ALL ON/ALL OFF—forces all relays to ON or OFF state. When in the ON state

inputs are temporarily disabled.

Many parameters can be modified using the LCD screen and a

password (setup code), however these modifications should be made

by a qualified factory technician.

Menu Structure

The top level menu structure for the programming functions is outlined below. Each of

the menu items shown below is covered in detail in separate sections of the

documentation. See Appendix B for a complete view of all top level menu items and

their submenus.

Deciphering the LCD Display Elements

The LCD display shows information on the current state of your relay panel, and

provides an easy and intuitive means of programming the panel.

When the system is operating normally the top line of the LCD display shows the

current day, time and the status of the event scheduler. The second line shows the

status of your relay cabinet.

If you exit from any menu via the MENU or CANCEL button,

and have not pressed Select/Save, all changes will be

lost.

MAIN MENU SELECT

SYSTEM SETTINGS

MAIN MENU SELECT

SCHEDULER

TUE 11:48A LE---

STATUS: NORMAL

MAIN MENU SELECT

SET TIME/DATE

MAIN MENU SELECT

CONFIG INPUTS

WEB VERSION

EZ-Max Plus Programming Guide Page 5

The example below shows the following:

• Daylight Savings Time is active.

• The display is locked.

• The Event Scheduler is active (“E”), but there are no events scheduled (the

dashes after the “E”). If there was an event currently running the display would

also show the event number (i.e.: LE003).

The table below explains what each of the elements in the display means. Notice that

uppercase and lowercase alpha characters have different meanings.

Display Description

Day and Time—12 or 24-Hour Mode

“a” or “p”

Lower case “a” or “p” indicates that daylight savings is inactive.

“A” or “P”

Uppercase “A” or “P” indicates that daylight savings is active.

Daylight Savings for 24-Hour Clock

“s”

Lower case “s” indicates that daylight savings is inactive.

“d”

Lower case “d” indicates that daylight savings is active.

Panel Lock Status

“L”

“L” indicates that the panel is in a locked state.

“u”

“u” indicates that the panel is in a temporary un-locked state and will

automatically lock after three minutes of inactivity.

“U”

“U” indicates that the panel is in an un-locked state and will not

automatically enabled the lock.

Event Scheduler

“E OFF” Event Scheduler is off.

“E---”

Event Scheduler is active but

no events have executed since the last system

reset/power cycle

.

“E1”

Any number displayed indicates the number of the last event executed.

TUE 11:48A LE---

STATUS: NORMAL

Day and Time

Daylight Savings Time is Active

Display is Locked

No Events Scheduled

WEB VERSION

EZ-MAX Plus User Interface LED’s

Page 6

Navigation Buttons

Use the arrow buttons to navigate the menu structure. Press the LEFT and

RIGHT buttons to navigate between “fields” on the screen. Press the UP

and DOWN buttons to change values in the fields.

You can use either the arrow keys or the keypad to change or enter data in many

cases.

Figure 3: Arrow Key & Alpha-Numeric Key Functions

Auto-Repeat

In some screens where you are adjusting values, you may find it helpful to press and

hold an arrow key. After a brief moment, the key will repeatedly issue it’s command

giving you a quick way to scroll through a broad range of values.

LED’s

Your EZ-MAX Plus relay cabinet has a variety of feedback mechanisms that are

designed to alert you as to how your panel is operating and the current status of each

relay.

The LED’s inside the panel can be broken up into two categories, “System Status” and

“Relay Status” LED’s.

System Status LED’s

System Status LED’s are designed to tell you at a quick glance the operational

characteristics of your system. For example, whether or not your system is receiving

data on one of the communication lines! This will assist you and our technical support

team should any diagnostics be necessary.

5

JKL

1

-

2

ABC

3

DEF

4

GHI

0

SPACE

6

MNO

7

PQRS

8

TUV

9

WXYZ

OR

{

FOR FIELD VALUE CHANGES

FOR FIELD

NAVIGATION

AND

After approximately three minutes of inactivity on any menu

screen, the LCD will revert back to the status screen.

WEB VERSION

EZ-Max Plus Programming Guide Page 7

Generally, the following conventions apply:

• Green – All Systems Go! No alerts detected.

• Flashing Green – All Systems Go! Receiving or transmitting data.

• Solid Red – Alert Condition. Specific alert depends on LED.

• Slow Flashing Red – Systems operating Normally, usually a heartbeat.

• Quick Flashing Red – Alert Condition or Override Condition, specific alert depends

on LED.

The specific functions and states of each System Status LED are listed in the table

below.

Figure 4: System Status LED Functions and States

LED Label LED State Indication

EMERGENCY Solid Red Indicates system is in emergency state

Off System is in Normal State

HEARTBEAT-C Slow Blinking Amber

(~1 bps)

Control Module Microprocessor is operating

properly

Fast Blinking Amber

(~2 bps)

Control module microprocessor is in boot mode

Off Control Module Microprocessor off line - usually

indicates system failure

Digital Station (Luma-Net

protocol)

Solid Green Configured (Negotiating a connection)

Off Disabled

Fast Flash Negotiating connections/initialization

Slow Flash Connected, TX/RX data

MODEM Solid Green Indicates modem is installed, enabled, and link is

established

5V POWER Solid Amber +5V power supply working normally

HEARTBEAT-R Slow Blinking Amber Relay Communications Microprocessor operating

properly

Fast Blinking Amber Relay Communications Microprocessor detects a

hardware alert

Off Relay Communications Microprocessor Off Line

WEB VERSION

EZ-MAX Plus User Interface Internal Relay Cabinet Controls

Page 8

Relay Status LED’s

Adjacent to each relay button you will find an LED that indicates the current status of

that particular relay card.

The possible states for the Relay Status LED’s are as follows:

Figure 5: Relay Status LED’s

Internal Relay Cabinet Controls

In addition to front panel controls, your EZ-MAX Plus cabinets have two different types

of internal override switches for the relays:

• Master Override Switch

• Relay Override Button

LED Label LED State Indication

RELAY X Solid Green Relay On

Off Relay Off

Blinking Green Relay Override On, could be either local

relay override, or if all relay LED’s are

blinking slowly more likely the master

override is On

All RELAYS All Relay LED’s

Short Off Long On

Master Override/Bypass On

All Relay LED’s, Long Off, Short On Master Override/Bypass Off

The inside of a relay cabinet, when energized, can be

DANGEROUS as HIGH VOLTAGES are present. Fatal accidents

are possible. Only trained authorized personnel should have

and gain access to the internal workings of your relay panel,

access is not required for any normal configuration or

operational purpose.

WEB VERSION

EZ-Max Plus Programming Guide Page 9

Master Override

See the figure below for the location of the master override. The master override has

three modes of operation:

• Normal—allows the Control Module and inputs to control the state of the relays.

• All ON—forces all of the relays to the ON state and the Control Module and inputs

can not turn the relays Off.

• All OFF—forces all of the relays to the OFF state and the Control Module and

inputs can not turn the relays On.

Figure 6: Location of Master Override Switch

WEB VERSION

EZ-MAX Plus User Interface Individual Relay Overrides

Page 10

Individual Relay Overrides

Each relay has an individual override button. See the Figures below for the location of

these buttons in each cabinet.

Figure 7: Location of Individual Relay Override Buttons in the 8 Cabinet

Switch

Inputs

EMERGENCY - TB17*

ETHERNET

OUT

JP9

RELAY 8

RELAY 7

RELAY 6

AC1

18 VAC IN

AC2

(OPTIONAL)

SERVICE ONLY

INTER-

FACE

J1

LCD

IN

S8

MODULE

MODEM

MODULE

OR

TB1

+24V

ON

RELAY 5

RELAY 4

RELAY 3

RELAY 2

RESET

JUMPER OFF IS DEFAULT

JUMPER ON PULLS INPUT HIGH

JP41

ETHERNET/MODEM

ALL RIGHTS RESREVED WORLDWIDE

OX-70129-00-00-02 BASIC

OX-70129-00-00-01 NETWORK

OUT

SELECTOR S1 THRU S8

ANALOG/SWITCH I/O*

COM

+24V

COM

OUT

IN

1

TB8

S7

TB7

S6

+24V

COM

+24V

COM

OUT

IN

S5

TB6

}

TB5

S1

LEVITON ASSEMBLY

C 2004 LEVITON MFG. CO.

RELAY

NO1

EMERGENCY

NORMAL

COM

TB3

OUT

COM

+24V

OUT

+24V

IN

S4

TB4

S3

OUT

COM

+24V

OUT

IN

S2

TB2

COM1

S14

S1

OFF

HEARTBEAT-R

5V POWER

ETH/MODEM

LUMANET

HEARTBEAT-C

EMERGENCY

D3 CAN1

D12

D27

D1

D8 CAN2

D4

D2

D6

D7

DMX

TB15

CAN 1

TERM

JP21

TERM

DMX

NC1

JP15

TERM

CAN 2

TB16

JP35

1 1

RELAY 1

LUMA-NET

SELECT

VOLTAGE

LUMA-NET

+12V

COM

TB17

COM.

EMERG.

J3

JP13

SWITCH

BYPASS

TERM

R+

R-

TB9

TRM

+V

COM

USB

TB9**

TB11

31

TB10

+24V

D-

COM

LCK

D+

TB13

11

MASTER/

SLAVE

DMX 512

TB10*

Switch Inputs and DMX Connector-

Wire Range #14 - #24 AWG

Torque2 LB-IN

Luma-Net Connector

Wire Range #12 - #24 AWG

Torque 5 LB-IN

Individual Relay

Override Switches

Master Override Switch

Individual Relay

Override Buttons

WEB VERSION

EZ-Max Plus Programming Guide Page 11

Figure 8: Location of Individual Relay Override Buttons in 16 and 24

cabinets

These buttons have one primary use with two modes of operation:

• Local override of individual relay without having to go through the Control Module.

• Temporary - Any control input with a higher priority can change its state.

• Locked Out - Event scheduler and control inputs, regardless of Priority will not

be able to alter its state.

Temporarily Overriding a Relay

Step 1: Open the cabinet door using the supplied key

Step 2: Press the button next to the relay you wish to change

The relay will audibly click when it changes states (ON to OFF and vice

versa)

There is a green LED above each relay override button. If the LED is

on, the relay is ON. If the LED is OFF, the relay is OFF.

Step 3: Press the button again to turn the relay on and off.

Pressing the individual relay override button will always clear higher

priority overrides for the relay. This allows manual control of the relay

even when Emergency or Master Override is active.

Locking out a Relay using its Override Button

Step 1: Open the cabinet door using the supplied key

Step 2: Get the relay to the state that you want to Lock it in. For example, if you

wish to lock the relay in the On state and it is Off, press the button one

time to toggle the relay to the On state.

Individual Relay

Override Switch

Individual Relay

Override Buttons

WEB VERSION

EZ-MAX Plus User Interface Individual Relay Overrides

Page 12

Step 3: Press and hold the button for approximately 5 seconds until the LED

beneath the button begins to blink.

The relay will audibly click when it changes states (ON to OFF and vice

versa)

There is a green LED above each relay override button. If the LED is

mostly on when it blinks, the relay is locked ON. If the LED is mostly

OFF when it blinks, the relay is locked OFF.

Unlocking a Relay Using its Override Button:

Step 1: Open the cabinet door using the supplied key

Step 2: Press and release the button of the relay that is locked out

The relay will change its state from On to Off or vice versa

WEB VERSION

EZ-Max Plus Programming Guide Page 13

Setting the Time, Date, and Astronomical Time Clock

Menu Overview

The top-level menu structure for date and time settings is below:

In addition to the three menu choices above, there is also a choice to VIEW ASTRO

CLOCK. This display screen cannot be edited.

Setting the Time

You can change the following fields in the Time display:

• 12 or 24-hour clock

• Hours

• Minutes

• AM or PM

• Daylight Savings Time Mode:

• OFF: Daylight savings time is disabled.

• US: Daylight savings time is set to “United States” daylight savings mode,

with one-hour adjustments in the fall and spring.

• EU: Daylight savings time is set to “European” daylight savings mode with

1 hour adjustments in the fall and spring, yet different dates then the US.

• US7: Daylights savings time is set to “United State” daylight savings mode

which became active in 2007 per the new Energy Conservation act.

MAIN MENU SELECT

SET TIME

MAIN MENU SELECT

SET DATE

MAIN MENU SELECT

SET TIME/DATE

MAIN MENU SELECT

SET ASTRO CLOCK

If Daylight Savings Time is active, the field will display in

upper case characters.

If Daylight Savings Time is inactive, the field will display in

lower case characters.

WEB VERSION

Setting the Time, Date, and Astronomical Time Clock Setting the Time

Page 14

Step 1: Press the MENU button.

Step 2: Press until the display reads as shown below, then press

SELECT/SAVE.

Step 3: Press SELECT/SAVE.

The display will show the current setting for the time.

Step 4: Use to navigate through the fields. Use to change the

settings for each field. For example, use to change the clock from a

12-hour clock to a 24-hour clock:

Step 5: Press SELECT/SAVE when you have finished editing the fields.

MAIN MENU SELECT

SET TIME/DATE

MAIN MENU SELECT

SET TIME

SET TIME 12 HOUR

4:46PM D: OFF

SET TIME 24 HOUR

16:46S D: US

The AM/PM field is only active for editing when

12-hour mode is active,.

If 24-hour mode is active, the AM/PM field is

replaced with an “s” or a “d” and is not editable.

Instead, the value is determined by the Daylight

Savings Time setting. The “s” indicates standard

time (Daylight Savings Time inactive); the “d”

indicates that Daylight Savings Time is active.

WEB VERSION

Page is loading ...

Leviton R08BD-208 Owner's manual

This manual is also suitable for

Leviton R08BD-208 Owner's manual

Related papers

Other documents