ATEN PE5220s User manual

NRGence™ eco PDU PE Series

PE5220s / PE5312sGL / PE5312sGR / PE5340s

Power Distribution Unit

User Manual

www.aten.com

eco PDU PE Series User Manual

ii

FCC, CE Information

FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE

STATEMENT: This equipment has been tested and found to comply with the

limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if

not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of this equipment in

a residential area is likely to cause harmful interference in which case the user

will be required to correct the interference at his own expense.

FCC Caution: Any changes or modifications not expressly approved by the

party responsible for compliance could void the user's authority to operate this

equipment.

CE Warning: This is a class A product. In a domestic environment this product

may cause radio interference in which case the user may be required to take

adequate measures.

RoHS

This product is RoHS compliant.

SJ/T 11364-2006

The following contains information that relates to China.

eco PDU PE Series User Manual

iii

User Information

Online Registration

Be sure to register your product at our online support center:

Telephone Support

For telephone support, call this number:

User Notice

All information, documentation, and specifications contained in this manual are subject to change

without prior notification by the manufacturer. The manufacturer makes no representations or

warranties, either expressed or implied, with respect to the contents hereof and specifically

disclaims any warranties as to merchantability or fitness for any particular purpose. Any of the

manufacturer's software described in this manual is sold or licensed as is. Should the programs

prove defective following their purchase, the buyer (and not the manufacturer, its distributor, or its

dealer), assumes the entire cost of all necessary servicing, repair and any incidental or

consequential damages resulting from any defect in the software.

The manufacturer of this system is not responsible for any radio and/or TV interference caused by

unauthorized modifications to this device. It is the responsibility of the user to correct such

interference.

The manufacturer is not responsible for any damage incurred in the operation of this system if the

correct operational voltage setting was not selected prior to operation. PLEASE VERIFY THAT

THE VOLTAGE SETTING IS CORRECT BEFORE USE.

International http://eservice.aten.com

International 886-2-8692-6959

China 86-10-5255-0110

Japan 81-3-5615-5811

Korea 82-2-467-6789

North America 1-888-999-ATEN ext 4988

United Kingdom 44-8-4481-58923

eco PDU PE Series User Manual

iv

PE Device Safety Notice

Consignes de sècuritè relatives à l’unitè PE

 Installez sur le circuit du bâtiment des disjoncteurs permettant d’assurer la

protection maximale autorisée, en respectant le courant nominal spécifié sur la

plaque signalétique. Veuillez respecter l’ensemble des réglementations nationales

en vigueur et des codes de sécurité ainsi que les déviations recommandèes pour

les disjoncteurs.

 Ne connectez l’unité PE qu’à une prise de courant avec borne de terre ou à un

système mis à la terre!

 Assurez-vous que le courant d’entrée total des systèmes connectés ne dépasse pas

le courant nominal spécifié sur la plaque signalétique de l’unité PE.

 Il existe un risque d’explosion si la batterie est remplacée par une batterie de type

incorrect. Jetez les batteries usagées en respectant les instructions adequates.

 Set the maximum permissible breaker protection in the building circuitry to the

current rating specified on the rating plate. Observe all national regulations and

safety codes as well as deviations for breakers.

 Only connect the PE Device to a grounded power outlet or a grounded system!

 Make sure that the total current input of the connected systems does not exceed

the current rating specified on the rating plate of the PE Device.

 There is a risk of explosion if the battery is replaced with an incorrect type.

Dispose of used batteries according to the relevant instructions.

eco PDU PE Series User Manual

v

Package Contents

The eco PDU PE Series package consists of:

1 PE5220s, PE5312sGL, PE5312sGR, or PE5340s Power Distribution Unit

1 Power Cord (PE5220s only)

1 Rack Mount Kit

1 User Instructions*

1CD-ROM

Check to make sure that all of the components are present and in good order.

If anything is missing, or was damaged in shipping, contact your dealer.

Read this manual thoroughly and follow the installation and operation

procedures carefully to prevent any damage to the eco PDU or other devices on

the installation.

* Features may have been added to the eco PDU since this manual was

published. Please visit our website to download the most up-to-date version.

Manual Date: 2013-12-23

All other brand names and trademarks are the registered property of their respective owners.

eco PDU PE Series User Manual

vi

Contents

FCC, CE Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii

SJ/T 11364-2006 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii

User Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii

Online Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii

Telephone Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii

User Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii

PE Device Safety Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iv

Consignes de sècuritè relatives à l’unitè PE . . . . . . . . . . . . . . . . . . . . .iv

Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v

About This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .ix

Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .ix

Product Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . x

Chapter 1.

Introduction

Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Comparison Charts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

PE5220sA / PE5220sB / PE5220sA-AX-J / PE5220sB-AX-J / PE5220sG

Comparison Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

PE5312sGL / PE5312sGR Comparison Chart . . . . . . . . . . . . . . . . . . . 3

PE5340sB / PE5340sG / PE5340sJ Comparison Chart . . . . . . . . . . . 4

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Power Distribution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Remote Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

eco Sensors Energy Management Software* . . . . . . . . . . . . . . . . . . . 6

Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Optional Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Cable Holders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

PE5220sB-AX-J / PE5220sB / PE5220sG Front View . . . . . . . . . . . . . 9

PE5220sA-AX-J / PE5220sA Front View . . . . . . . . . . . . . . . . . . . . . . 11

PE5312sGL Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

PE5312sGR Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

PE5340s Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

PE5220s Readout Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

PE5312s / PE5340s Readout Section . . . . . . . . . . . . . . . . . . . . . . . . 20

Chapter 2.

Hardware Setup

Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

eco PDU PE Series User Manual

vii

Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

PDU Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Securing the Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Securing the Sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

Chapter 3.

Basic Operation and

First Time Setup

Operation Methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Browser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

eco Sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

SNMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

First Time Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Network Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Changing the Administrator Login . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Moving On. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Chapter 4.

Browser Operation

Logging In . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

The eco PDU Main Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Page Components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Outlet Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

Bank Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37

User . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Administrator Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

User Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

The System Log Event List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Device Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Date/Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Login Failures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49

Working Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Account Policy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50

Login String / IP Filter / Mac Filter . . . . . . . . . . . . . . . . . . . . . . . . . . .51

Authentication & Authorization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54

Private Certificate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

PDU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Firmware File. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57

Backup/Restore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

eco PDU PE Series User Manual

viii

Appendix

Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Consignes de sécurité . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Général . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

The eco PDU’s Main Power Cord . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Securing the Power Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Montage sur bâti . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

Le cordon d’alimentation principale de l’unité d’alimentation éco . . . . 67

Fixation des câbles d’alimentation . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

International . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

North America . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

IP Address Determination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

PE5220sA / PE5220sA-AX-J . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

PE5220sB / PE5220sB-AX-J . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

PE5220sG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

PE5312sGL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

PE5312sGR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

PE5340sB / PE5340sJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

PE5340sG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

Administrator Login Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

eco PDU PE Series User Manual

ix

About This Manual

This User Manual is provided to help you get the most from your eco PDU

system. It covers all aspects of installation, configuration and operation. An

overview of the information found in the manual is provided below.

Chapter 1, Introduction, introduces you to the eco PDU system. Its purpose,

features and benefits are presented, and its front and back panel components

are described.

Chapter 2, Hardware Setup, provides step-by-step instructions for setting

up your installation.

Chapter 3, Basic Operation and First Time Setup, explains the

procedures that the Administrator employs to set up the eco PDU network

environment, and change the default username and password.

Chapter 4, Browser Operation, describes how to log in to the eco PDU with

an internet browser, and explains the layout and components of the eco PDU’s

user interface.

An Appendix, provides specifications and other technical information

regarding the eco PDU.

Conventions

This manual uses the following conventions:

Monospaced Indicates text that you should key in.

[ ] Indicates keys you should press. For example, [Enter] means

to press the Enter key. If keys need to be chorded, they

appear together in the same bracket with a plus sign

between them: [Ctrl+Alt].

1. Numbered lists represent procedures with sequential steps.

♦ Bullet lists provide information, but do not involve sequential

steps.

→ Indicates selecting the option (on a menu or dialog box, for

example), that comes next. For example, Start

→ Run

means to open the Start menu, and then select Run.

Indicates critical information.

eco PDU PE Series User Manual

x

Product Information

For information about all NRGence™ products and how they can help you

save money in the data center, visit NRGence™ on the Web or contact an

ATEN Authorized Reseller. Visit ATEN on the Web for a list of locations and

telephone numbers

 International – http://www.aten.com

 North America – http://www.aten-usa.com

1

Chapter 1

Introduction

Overview

As part of its NRGence™ line, ATEN has developed a new generation of green

energy power distribution units (PDUs) to effectively increase the efficiency of

data center power usage. The NRGence™ PE5220s, PE5312sGL,

PE5312sGR, and PE5340s are intelligent PDUs that contain 12/20/40 AC

outlets and are available in IEC or NEMA input configurations. The basic

characteristics of each model are shown in the tables on page 4.

The PE5220s, PE5312sGL, PE5312sGR, and PE5340s provide secure,

centralized, intelligent, power management of data center IT equipment

(servers, storage systems, KVM switches, network devices, serial data devices,

etc.), as well as the ability to monitor the data center's environmental health via

sensors*.

NRGence™ eco PDUs offer remote power control combined with real-time

power measurement - allowing you to control and monitor the power status of

devices attached to the PDUs, either at the PDU device or bank level, from

practically any location via a TCP/IP connection.

The eco PDU also offers comprehensive power analysis reports which can

separate departments and locations, providing precise measurements of

current, voltage, power and watt-hour in a real-time display.

Installation and operation is fast and easy: plugging cables into their

appropriate ports and user-friendly browser-based management is all that is

entailed. Since the eco PDU firmware is upgradeable over the net, you can stay

current with the latest improvements by simply downloading updates from our

website as they become available.

NRGence™ eco PDUs support any 3rd party V1, V2, V3 SNMP Manager

Software and NRGence™ eco Sensors software (eco PDU Manager Software).

eco Sensors provide you with an easy method for managing multiple devices,

offering an intuitive and user-friendly Graphical User Interface that allows you

to configure a PDU device and monitor the power status of the equipment

connected to it.

(Continues on next page.)

eco PDU PE Series User Manual

2

(Continued from previous page.)

With its advanced security features and ease of operation, the PE5220s

PE5312sGL, PE5312sGR, and PE5340s eco PDUs are the most convenient,

most reliable, and most cost effective way to remotely manage power access

for multiple computer installations and allocate power resources in the most

efficient way possible.

Note: 1. Sensors are optional accessories. A sensor-enabled installation is

required to generate more complete energy-efficient data readings

and charts. Higher sensor installation density is helpful to generate

more accurate data. See Optional Accessories, page 8, for further

information.

2. eco PDUs are primarily designed for access via Intranet; extra

network security protection is suggested for Internet access usage.

Chapter 1. Introduction

3

Comparison Charts

PE5220sA / PE5220sB / PE5220sA-AX-J / PE5220sB-AX-J /

PE5220sG Comparison Chart

PE5312sGL / PE5312sGR Comparison Chart

Model Inlet / Cord Outlets

Meter-

ing Level

Amps

Per Duplex

Receptacle

Outlet

Bank Total

PE5220sA NEMA 5-20P 20 NEMA 5-15R Bank

12A (UL),

15A (Max).

{Per

outlet}

16A

(UL),

20A

(Max)

16A

(UL),

20A

(Max)

PE5220sB NEMA 6-20P IEC C13

12A (UL),

15A (Max)

PE5220sA-

AX-J

NEMA L5-

20P

NEMA 5-15R

12A (UL),

15A (Max).

{Per

outlet}

16A

(UL),

20A

(Max)

16A

(UL),

20A

(Max)

PE5220sB-

AX-J

NEMA L6-

20P

IEC C13

12A (UL),

15A (Max)

16A

(UL),

20A

(Max)

16A

(UL),

20A

(Max)

PE5220sG IEC 60320

C20

IEC C13

10A 15A

(CB),

16A

(Max)

15A

(CB),

16A

(Max)

Model Inlet / Cord Outlets

Metering

Level

Amps

Per Outlet Bank Total

PE5312sGL IEC 60309

32A

12 Bank1: Outlet

1–6 ; 6 x UK

BS1363

Bank2: Outlet

7 –12 ; 6 x UK

BS1363

Bank

BS1363:

13A (Max)

16A

(Max),

TUV De-

rated 15A

(Max)

32A

(Max),

TUV

De-

rated

30A

(Max)

PE5312sGR IEC 60309

32A

Bank1: Outlet

1–6 ; 6 x UK

BS1363

Bank2: Outlet

7 –12 ; 6 x UK

BS1363

BS1363:

13A (Max)

16A

(Max),

TUV De-

rated 15A

(Max)

32A

(Max),

TUV

De-

rated

30A

(Max)

eco PDU PE Series User Manual

4

PE5340sB / PE5340sG / PE5340sJ Comparison Chart

Note: The PE5340sJ is identical to the B model but has power cords designed

for the Japanese market. For the complete specifications of individual

models, please reference Specifications, page 72.

Model Inlet / Cord Outlets

Metering

Level

Amps

Per Duplex

Receptacle

Outlet

Bank Total

PE5340sB NEMA L6-30P 40 Bank 1:

Outlet 1–20:

20 x C13

Bank 2:

Outlet 21–40:

20 x C13

Bank

12A (UL),

15A (Max)

12A

(UL),

15A

(Max)

24A

(UL),

30A

(Max)

PE5340sJ

PE5340sG IEC 60309

32A

10A 15A

(TUV)

16A

(Max)

30A

(TUV)

32A

(Max)

Chapter 1. Introduction

5

Features

Power Distribution

 Space saving 0U rack mount design with rear mounting

 IEC or NEMA outlet models

 3 digit 7-segment front panel LED shows PDU/Phase / Bank / IP

(PE5312sGL/PE5312sGR/PE5340s), or PDU Amp / IP (PE5220s)

 Remote users can monitor PDU / Bank status via web GUI from most

internet browsers

 Safe shutdown support

 Separate power for the unit's own power and its power outlets. The user

interface is still accessible even when an overload condition trips the

devices' circuit breaker

Remote Access

 Remote power control via TCP/IP and a built in 10/100 Ethernet port

 Network Protocols: TCP/IP, UDP, HTTP, HTTPS, SSL, SMTP, DHCP,

NTP, DNS, auto sense, Ping

 eco PDU Power Management software – eco Sensors

 Supports SNMP Manager V1, V2 & V3

Operation

 Supports multiple power control methods – Wake on LAN, System after

AC Back, Kill the Power

 Power-on sequencing – users can set the power on sequence and delay

time for each port to allow equipment to be turned on in the proper order

 Easy setup and operation via a browser-based user interface

 Multibrowser support (IE, Mozilla, Firefox, Chrome, Safari, Opera,

Netscape)

 RTC support to keep the timer running during times of no power.

 Supports up to 8 user accounts and 1 administrator account; supports 2

concurrent logins

eco PDU PE Series User Manual

6

Management

 Power status measurement at the PDU/Bank level

 LED indicators for current and IP address at the PDU device and at the

Bank (PE5340s only) level

 Real-time aggregate current, voltage, power, and power dissipation

displayed in a browser-based UI for monitoring at the PDU and bank level.

 Environment monitoring – supports external temperature / humidity /

differential pressure sensors for rack environment monitoring

 Current and voltage threshold setting

 Naming support for outlets

 User outlet access assignment on an outlet-by-outlet basis.

 Event logging and syslog support

 Upgradeable firmware

 Multilanguage support: English, Traditional Chinese, Simplified Chinese,

Japanese, German, Italian, Spanish, French, Russian, Korean, Portuguese.

Security

 Two-level password security

 Strong security features include strong password protection and advanced

encryption technologies – 128 bit SSL

 Remote authentication support: RADIUS

eco Sensors Energy Management Software*

 Automatic discovery of all PE devices within the same intranet

 Remote real-time power measurement and monitoring

 Real-time environment sensor monitoring

 Plotting/monitoring of all PE devices

 Exceed threshold alert through SMTP and System log

 Power Analysis report

Note: eco Senors is designed to work with NRGence™ PDUs, and is bundled

with all PE series packages.

Chapter 1. Introduction

7

Requirements

 Browsers accessing the eco PDU unit must support SSL 128 bit

encryption.

 For cold booting of attached computers, the computer's BIOS must

support Wake on LAN or System after AC Back.

 For Safe Shutdown:

 The computer must be running Windows (Windows 2000 or higher) or

Linux.

 The Safe Shutdown program (available by download from our website

or on the software CD included), must be installed and running on the

computer.

eco PDU PE Series User Manual

8

Optional Accessories

Sensors

Sensors are optional accessories. You can use the eco PDU unit without

sensors. However, if you want to have complete energy management of an

instrumented data center with the use of the eco PDU, you would need to use

eco Sensors software and install 4 sensors for each of the racks to generate a

complete energy-efficient data reading and chart. Higher sensor installation

density is helpful to generate more accurate data. 16/20/24-port models have 2

sensor ports. In this case, Sensor 1 needs to be installed at the intake of the rack

and sensor 2 needs to be placed at the exhaust of IT equipment of the rack. A

sensor-enabled installation is required to generate a more complete energy-

efficient data reading and chart. Higher sensor installation density is helpful to

generate more accurate data. Available sensors are show in the table, below:

Sensor Management

Sensors can be managed via the eco PDU’s built-in graphical user interface

(GUI) or with the NRGence™ eco Sensors software that can be downloaded

from the ATEN website. The download link can be found on the software CD

provided with the eco PDU package.

Cable Holders

Cable holders are optional accessories. For added safety, use ATEN Lok-U-

Plug cable holders to secure the cables from your attached devices in place on

the eco PDU unit. Use only the ATEN Lok-U-Plug cable holders that have

been specifically designed to work with the eco PDU. Using any other kind of

cable securing device could be highly dangerous.

Sensor Part Number

Temperature EA1140

Temperature / Humidity EA1240

Differential Pressure / Temperature EA1340

Part Number Description

2X-EA07 Lok-U-Plug Cable Holder (10 pcs)

2X-EA08 Lok-U-Plug Installation Tool (4 pcs)

Chapter 1. Introduction

9

Components

PE5220sB-AX-J / PE5220sB / PE5220sG Front View

1

3

4

5

6

2

eco PDU PE Series User Manual

10

Note: Holes for ATEN Lok-U-Plug cable holders are located around the

outlets. See Securing the Cables, page 25, for further information.

No. Item Description

1 Power Inlet The power cord that connects the unit to an AC

power source plugs into this NEMA L6-20R socket

(PE5220sB-AX-J); NEMA 6-20R socket

(PE5220sB); or IEC 60320 C19 socket

(PE5220sG).

2 Circuit Breaker

Pushbutton

As a safety measure, if there is an over-current

situation regarding the device’s power, the circuit

breakers will trip. Press the button to recover

normal operation.

3 Sensor Ports External sensors plug into these two RJ-11 ports.

4 LAN Port and LEDs The cable that connects the eco PDU to the LAN

plugs in here. The Link and LAN LEDs are built

into the LAN port:

Link: Lights GREEN to indicate that a connection

via the eco PDU's RJ-45 Ethernet port has been

established. Flashes to indicate data is being

transmitted.

LAN: Lights ORANGE to indicate 10 Mbps data

transmission speed. The LED lights GREEN to

indicate 100 Mbps data transmission speed.

5 Readout Section, LEDs

and Reset Switch

Details of this section are provided on page 19.

6 Power Outlets 20 x IEC 60320 C13

Page is loading ...

ATEN PE5220s User manual

This manual is also suitable for

ATEN PE5220s User manual

Related papers

Other documents