Aero-Flex GGL01-8 Operating instructions

Brand
Aero-Flex
Model
GGL01-8
Type
Operating instructions

This manual is also suitable for

1
15 m
50’
WARNINGS
To use Glider assembly, remove the Universal cap (press finger tabs
to open or use a screwdriver and disengage). Install four line blades
(alternate colors). Make sure lines are properly installed over posts and
onto slots. Connect the Glider cap. Be sure Glider cap and tabs are
fully snapped in place.
fits both
3.5” 5”
Glider assembly cap must be removed. Use hex allen wrench to un-
screw the glider clockwise. Remove button from 5” convertible cap.
With bearing and bolt, install Glider to 5” cap with hex allen wrench.
Hand tighten to 40”# counter-clockwise. Install lines; install assembly
to 5” head receiver. Make sure tabs are securely in place.
The Glider is for ground-supported trimming, which is not a
recommended technique for trimming heavy vegetation.
Do not use the glider for slashing heavy weeds or vines. Remove the
glider and reinstall the stock cap before trimming very tall grass.
Level Cut: rest on the
ground
Low Cut: tilt on the
ground
High Cut: lift o the ground
(manual control)
Corte Nivel: reposo en el
suelo
Corte Bajo: incline sobre
el terreno
Corte Alto: levantarse del
suelo (control manual)
When trimming tall vegetation, start from the top and work your way
down to avoid long strands wrapping in the mechanism.
To minimize the risk of injury from thrown objects, ensure safe shield alignment, and run the
trimmer at lower speeds. Be sure to wear proper eye and body protection.
Protect
bystanders
Flying debris
& blade
contact
Vibration
Do not use
without a
shield
Read/follow
instructions
1
1
2
2
3
3
4
4
1
1
1
2
2
2
5
76 8 9
INSTALLATION, METHODS, & USE
INSTALL THE GLIDER TO YOUR 3.5” AERO-FLEX® UNIVERSAL TRIMMING SYSTEM
INSTALL THE GLIDER TO YOUR 5” AERO-FLEX® CONVERTIBLE TRIMMING SYSTEM
WHEN TO REMOVE THE GLIDER
3.5”
5”
MINIMIZE WRAPPING
Aero-Flex® Glider
UPDATES: www.aero-flex.com
GLIDER TECHNIQUES
VARY CUTTING HEIGHT
AF 7.10.17
2
REMOVE DEBRIS BEFORE FURTHER USE
CCW
CW
THIS LIMITED WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES. ANY IMPLIED WAR-
RANTY OF FITNESS OR PARTICULAR PURPOSE, MERCHANTABILITY SHALL BE LIMITED IN DURA-
TION TO THE DURATION OF THIS LIMITED WARRANTY. AERO-FLEX TECHNOLOGIES, INC. SHALL
NOT BE LIABLE FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES.
Aero-Flex® Technologies, Inc. warrants this product against defects in material and workmanship for a
period of 30 days from date of original retail purchase. Warranty does not apply to any misuse of the
product. This limited warranty is non transferable and does not cover damage resulting from any mis-
use from contact with sidewalks, rocks or other structures nor any damage caused by improper instal-
lation or improper maintenance. Your specific legal rights may vary from state to state. For Safety or
Technical Questions and Updates, see the Safety & Instructions tab on our website www.aero-flex.com
Contact us at directly info@aero-flex.com or call us toll-free 888.880.AERO (2376)
U.S. Patents: #D710,663S; 5,761,816; 5,996,233; 6,161,292; 6,176,015B1 (others pending)
Though Aero-Flex® Line Blades are more durable than monofilament line,
they are not designed to withstand overgrown weeds, brush, or other hard
obstructions that would normally require a metal blade.
If wrapping does occur, stop engine and remove by hand or with a tool. Grab debris while
twisting the head in its reverse operating direction to unravel. *If Glider releases during use,
snap it back into place on the head. Do not install if tabs are damaged.
If the Glider unthreads from the cap, add 1 drop of Loctite 222 to bolt, make
sure bearing is attached, and tighten to 40”# (reverse thread) onto cap.
See aero-flex.com for video instructions
If Glider releases at the tabs and the entire cap releases, ensure proper
line installation and fully snap the cap back into place.
When trimming along solid ob-
structions, work in the direction
of the thrust.
Run at part throttle. Do not force
the line blades into abrasive ob-
jects. Cut with the outer tips of
the line blades.
1
2
3
4
LIMITED WARRANTY
RELEASED GLIDER
PREVENT LINE BLADE FAILURE
WARNINGS
Aero-Flex® Glider
UPDATES: www.aero-flex.com
INCREASE LINE BLADE LIFE
AF 7.10.17
  • Page 1 1
  • Page 2 2

Aero-Flex GGL01-8 Operating instructions

Brand
Aero-Flex
Model
GGL01-8
Type
Operating instructions
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents