Supermicro A2SAN-H-WOHS User manual

USER’S MANUAL

Revision 1.0c

A2SAN-H/-E/-L

A2SAN-H/-E/-L-WOHS

X11SAN

X11SAN-WOHS

The information in this user’s manual has been carefully reviewed and is believed to be accurate. The vendor assumes

no responsibility for any inaccuracies that may be contained in this document, and makes no commitment to update

or to keep current the information in this manual, or to notify any person or organization of the updates. Please Note:

For the most up-to-date version of this manual, please see our website at www.supermicro.com.

Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product described in this manual

at any time and without notice. This product, including software and documentation, is the property of Supermicro and/

or its licensors, and is supplied only under a license. Any use or reproduction of this product is not allowed, except

as expressly permitted by the terms of said license.

IN NO EVENT WILL Super Micro Computer, Inc. BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL,

SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO USE THIS PRODUCT

OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN PARTICULAR, SUPER

MICRO COMPUTER, INC. SHALL NOT HAVE LIABILITY FOR ANY HARDWARE, SOFTWARE, OR DATA STORED

OR USED WITH THE PRODUCT, INCLUDING THE COSTS OF REPAIRING, REPLACING, INTEGRATING,

INSTALLING OR RECOVERING SUCH HARDWARE, SOFTWARE, OR DATA.

Any disputes arising between manufacturer and customer shall be governed by the laws of Santa Clara County in the

State of California, USA. The State of California, County of Santa Clara shall be the exclusive venue for the resolution

of any such disputes. Supermicro's total liability for all claims will not exceed the price paid for the hardware product.

FCC Statement: This equipment has been tested and found to comply with the limits for a Class B digital device

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in accordance with the manufacturer’s instruction manual,

may cause harmful interference with radio communications. Operation of this equipment in a residential area is likely

to cause harmful interference, in which case you will be required to correct the interference at your own expense.

California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate warning applies only

to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate Material-special handling may apply.

See www.dtsc.ca.gov/hazardouswaste/perchlorate.

The products sold by Supermicro are not intended for and will not be used in life support systems, medical equipment,

nuclear facilities or systems, aircraft, aircraft devices, aircraft/emergency communication devices or other critical

systems whose failure to perform be reasonably expected to result in signicant injury or loss of life or catastrophic

property damage. Accordingly, Supermicro disclaims any and all liability, and should buyer use or sell such products

for use in such ultra-hazardous applications, it does so entirely at its own risk. Furthermore, buyer agrees to fully

indemnify, defend and hold Supermicro harmless for and against any and all claims, demands, actions, litigation, and

proceedings of any kind arising out of or related to such ultra-hazardous use or sale.

Manual Revision 1.0c

Release Date: August 15, 2019

Unless you request and receive written permission from Super Micro Computer, Inc., you may not copy any part of this

document. Information in this document is subject to change without notice. Other products and companies referred

to herein are trademarks or registered trademarks of their respective companies or mark holders.

Printed in the United States of America

WARNING: This product can expose you to chemicals including

lead, known to the State of California to cause cancer and birth

defects or other reproductive harm. For more information, go

to www.P65Warnings.ca.gov.

!

3

Preface

About This Manual

This manual is written for system integrators, IT technicians and knowledgeable end users.

It provides information for the installation and use of the A2SAN-H/-E/-L and X11SAN

motherboard.

About This Motherboard

The A2SAN-H/-E/-L and X11SAN motherboard provides powerful graphics and increased

media processing performance with multi-frame technology. Paired with the Intel® Atom SoC

(System-on-a-Chip) processor, the A2SAN-H/-E/-L and X11SAN delivers more computing

power for faster memory speeds and bandwidth while maintaining energy efciency. Utilizing

Intel® TCC (Time Coordinated Computing) Technology, the A2SAN-H/-E/-L and X11SAN

resolves latency issues in applications and improves determinism across connected devices.

The motherboard features advanced technologies such as Intel® Virtualization to improve

security and reliabity of systems, and Thermal Monitoring to reduce power consumption. It

also comes with more I/O ports and high-speed connectivity.

Please note that this motherboard is intended to be installed and serviced by professional

technicians only. For processor/memory updates, please refer to our website at http://www.

supermicro.com/products/.

Conventions Used in the Manual

Special attention should be given to the following symbols for proper installation and to prevent

damage done to the components or injury to yourself:

Warning! Indicates high voltage may be encountered when performing a procedure.

Warning! Indicates important information given to prevent equipment/property damage

or personal injury.

Important: Important information given to ensure proper system installation or to

relay safety precautions.

Note: Additional Information given to differentiate various models or provides infor-

mation for correct system setup.

4

Contacting Supermicro

Headquarters

Address: Super Micro Computer, Inc.

980 Rock Ave.

San Jose, CA 95131 U.S.A.

Tel: +1 (408) 503-8000

Fax: +1 (408) 503-8008

Email: [email protected] (General Information)

[email protected] (Technical Support)

Website: www.supermicro.com

Europe

Address: Super Micro Computer B.V.

Het Sterrenbeeld 28, 5215 ML

's-Hertogenbosch, The Netherlands

Tel: +31 (0) 73-6400390

Fax: +31 (0) 73-6416525

Email: [email protected] (General Information)

[email protected] (Technical Support)

[email protected] (Customer Support)

Website: www.supermicro.nl

Asia-Pacic

Address: Super Micro Computer, Inc.

3F, No. 150, Jian 1st Rd.

Zhonghe Dist., New Taipei City 235

Taiwan (R.O.C)

Tel: +886-(2) 8226-3990

Fax: +886-(2) 8226-3992

Email: [email protected]

Website: www.supermicro.com.tw

Super A2SAN-H/-E/-L and X11SAN User's Manual

5

Table of Contents

Chapter 1 Introduction

1.1 Checklist ...............................................................................................................................7

Quick Reference ...............................................................................................................13

Quick Reference Table ......................................................................................................14

Motherboard Features .......................................................................................................15

1.2 Processor Overview ...........................................................................................................19

1.3 Special Features ................................................................................................................19

Recovery from AC Power Loss .........................................................................................20

1.4 ACPI Features ....................................................................................................................20

1.5 Power Supply .....................................................................................................................20

1.6 Super I/O ............................................................................................................................20

1.7 Advanced Power Management ..........................................................................................21

Management Engine (ME) ................................................................................................21

Chapter 2 Installation

2.1 Static-Sensitive Devices .....................................................................................................22

Precautions .......................................................................................................................22

Unpacking .........................................................................................................................22

2.2 Motherboard Installation .....................................................................................................23

Tools Needed ....................................................................................................................23

Location of Mounting Holes ..............................................................................................23

Installing the Motherboard.................................................................................................24

2.3 Memory Support and Installation .......................................................................................25

Memory Support ................................................................................................................25

SO-DIMM Installation ........................................................................................................26

SO-DIMM Removal ...........................................................................................................26

2.4 Rear I/O Ports ....................................................................................................................27

2.5 Front Control Panel ............................................................................................................31

2.6 Connectors .........................................................................................................................34

Power Connections ...........................................................................................................34

Headers .............................................................................................................................36

2.7 Jumper Settings .................................................................................................................45

Preface

6

How Jumpers Work ...........................................................................................................45

2.8 LED Indicators ....................................................................................................................48

Chapter 3 Troubleshooting

3.1 Troubleshooting Procedures ..............................................................................................49

Before Power On ..............................................................................................................49

No Power ..........................................................................................................................49

No Video ...........................................................................................................................50

System Boot Failure .......................................................................................................50

Memory Errors ..................................................................................................................50

Losing the System's Setup Conguration .........................................................................51

When the System Becomes Unstable ..............................................................................51

3.2 Technical Support Procedures ...........................................................................................53

3.3 Frequently Asked Questions ..............................................................................................54

3.4 Battery Removal and Installation .......................................................................................55

Battery Removal ................................................................................................................55

Proper Battery Disposal ....................................................................................................55

Battery Installation .............................................................................................................55

3.5 Returning Merchandise for Service ....................................................................................56

Chapter 4 BIOS

4.1 Introduction .........................................................................................................................57

Starting the Setup Utility ...................................................................................................57

4.2 Main ....................................................................................................................................58

4.3 Advanced ............................................................................................................................60

4.4 Security ...............................................................................................................................85

4.5 Boot ....................................................................................................................................89

4.6 Save & Exit .........................................................................................................................91

Appendix A BIOS Codes

Appendix B Software Installation

B.1 Installing Software Programs .............................................................................................95

B.2 SuperDoctor

®

5 ...................................................................................................................96

Appendix C Standardized Warning Statements

Battery Handling ................................................................................................................97

Product Disposal ...............................................................................................................99

Super A2SAN-H/-E/-L and X11SAN User's Manual

7

Chapter 1: Introduction

Main Parts List (Retail Single Package)

Description Part Number Quantity

Supermicro Motherboard with passive heatsink

A2SAN-H/-E/-L

A2SAN-H/-E/-L-WOHS (without heatsink)

X11SAN

X11SAN-WOHS

1

Audio cable (20cm) CBL-OTHR-0986 1

SATA power cable (25cm) CBL-PWEX-0982 1

USB 2.0 cable (20cm) CBL-CUSB-0983 1

COM cable (20cm) CBL-CUSB-0984 1

SATA data cable (25cm) CBL-SAST-0881 1

Quick Reference Guide MNL-1935-QRG 1

Main Parts List (Bulk Package)

Description Part Number Quantity

Supermicro Motherboard with passive heatsink

A2SAN-H/-E/-L

A2SAN-H/-E/-L-WOHS (without heatsink)

X11SAN

X11SAN-WOHS

1

SATA power cable (25cm) CBL-PWEX-0982 1

SATA data cable (25cm) CBL-SAST-0881 1

Optional Parts List

Description Part Number Quantity

Mini PCI-E extended bracket MCP-110-00097-0N 1

M.2 Module Bracket (for 2242/3042 module support) MCP-290-00161-0N 1

Chapter 1

Introduction

Congratulations on purchasing your computer motherboard from an industry leader. Supermicro

boards are designed to provide you with the highest standards in quality and performance.

In additon to the motherboard, several important parts that are included with the system are

listed below. If anything listed is damaged or missing, please contact your retailer.

1.1 Checklist

8

Super A2SAN-H/-E/-L and X11SAN User's Manual

Important Links

For your system to work properly, please follow the links below to download all necessary

drivers/utilities and the user’s manual for your server.

• Supermicro product manuals: http://www.supermicro.com/support/manuals/

• Product drivers and utilities: https://www.supermicro.com/wftp/driver/

• Product safety info: http://www.supermicro.com/about/policies/safety_information.cfm

• If you have any questions, please contact our support team at: [email protected]m

This manual may be periodically updated without notice. Please check the Supermicro website

for possible updates to the manual revision level.

9

Chapter 1: Introduction

Figure 1-1. A2SAN-H Motherboard Image

Note: All graphics shown in this manual were based upon the latest PCB revision

available at the time of publication of the manual. The motherboard you received may

or may not look exactly the same as the graphics shown in this manual.

Figure 1-2. A2SAN-H-WOHS Motherboard Image

10

Super A2SAN-H/-E/-L and X11SAN User's Manual

Figure 1-3. A2SAN-H/-E/-L and X11SAN

Motherboard Mechanical Drawings

Motherboard Top Side

Motherboard Bottom Side

11

Chapter 1: Introduction

Figure 1-4. A2SAN-H/-E/-L and X11SAN

Back Panel I/O Mechanical Drawings

Back Panel I/O With Heatsink (A2SAN-H/-L)

Back Panel I/O Without Heatsink (X11SAN-WOHS, A2SAN-H/E/L-WOHS)

Back Panel I/O With Heatsink (X11SAN)

Back Panel I/O With Heatsink (A2SAN-E)

12

Super A2SAN-H/-E/-L and X11SAN User's Manual

DESIGNED IN USA

A2SAN-L

REV: 2.00

JGP1

BT1

JCOM1: COM1/COM2

JCOM2: COM3/COM4

CPU1

FAN1

JPME2

JPF1

LAN1LAN2

JD1

LVDS1

I-SATA1

JHDMI1

LED1

JLCDPWR1

JF1

JIP1

JPH1

JCOM3: COM5/COM6

AUDIO FP

USB6(3.1)

X

USB2/3

USB0/1

VGA

JF1

ONPWR

RST

X

HDD LED

PWR LED

SPEAKER

JD1:

USB4/5(3.0)

JMD1

JPW1

JMP1

JLPC80

JSMBUS1

J5

JPT1

BAR CODE

Top Layout

Bottom Layout

Figure 1-5. Motherboard Layout

(not drawn to scale)

Note: Components not documented are for internal testing only.

13

Chapter 1: Introduction

JMD1

JPW1

JMP1

JLPC80

JSMBUS1

J5

JPT1

BAR CODE

Quick Reference

Notes:

• See Chapter 2 for detailed information on jumpers, I/O ports, and JF1 front panel con-

nections.

• " " indicates the location of Pin 1.

• Jumpers/LED indicators not indicated are used for testing only.

• Use only the correct type of onboard CMOS battery as specied by the manufacturer.

DESIGNED IN USA

A2SAN-L

REV: 2.00

JGP1

BT1

JCOM1: COM1/COM2

JCOM2: COM3/COM4

CPU1

FAN1

JPME2

JPF1

LAN1LAN2

JD1

LVDS1

I-SATA1

JHDMI1

LED1

JLCDPWR1

JF1

JIP1

JPH1

JCOM3: COM5/COM6

AUDIO FP

USB6(3.1)

X

USB2/3

USB0/1

VGA

JF1

ONPWR

RST

X

HDD LED

PWR LED

SPEAKER

JD1:

USB4/5(3.0)

USB4/5 (3.0)

JHDMI

JIP1

JPME2

USB2/3

USB0/1

JGP1

LAN1

CPU1

FAN1

LVDS1

I-SATA1

JF1

JCOM2

JLCDPWR1

JCOM1

BT1

AUDIO FP

JPH1

JD1

LED1

LAN2

USB6 (3.1)

VGA

JPF1

JSMBUS1

JLPC80

JMD1

JMP1

J5

JPW1

JPT1

JCOM3

14

Super A2SAN-H/-E/-L and X11SAN User's Manual

Quick Reference Table

Jumper Description Default Setting (*)

JLCDPWR1 LVDS Panel VCC Power 3.3V / 5V / 12V

Pins 1-3* (3.3V)

Pins 3-5 (5V)

Pins 3-4 (12V)

JPF1 Power Force On

Pins 1-2* (Power Force On)

Pins 2-3 (PWR BTN Power On)

JPME2 Manufacturing Mode

Pins 1-2* (Normal)

Pins 2-3 (Manufacturing Mode)

JPT1 TPM Enable/Disable Header

JPT1_1N2* (Enable)

JPT1_3N4 (Disable)

LED Description Status

LED1 Power LED (for debugging only)

Solid Green: S0 mode

Solid Red: S3/S4/S5 modes

Connector Description

AUDIO FP Front Panel Audio Header (Mic-in/Headphone-out)

BT1

Battery Connector

(To Clear CMOS, remove the battery, short pins 1-2 for more than 10 seconds and

install the battery.)

FAN1 System Fan Header

I-SATA1 Intel® PCH SATA 3.0 Port

JCOM1: COM1/COM2

JCOM2: COM3/COM4

JCOM3: COM5/COM6

Serial COM Ports (JCOM1 supports RS232/RS422/RS485)

Serial COM Ports (JCOM2 supports RS232)

Serial COM Ports (JCOM3 supports RS232) (Only supported on A2SAN-H-WOHS)

JD1 Speaker Header

JF1 Front Control Panel Header

JGP1 General Purpose I/O Header

JHDMI Back Panel HDMI Port

JIP1 LVDS Inverter Power Header

JLPC80 Port 80 Connector (for debugging only)

JMD1 M.2 Slot (B-KEY) (supports PCIe Gen2 x 1 / SATA / USB 2.0)

JMP1 Mini PCI-E Slot (supports PCIe Gen2 x 1 / USB 2.0)

JPH1 SATA Power Connector (for one HDD system)

JPW1 4-pin 12V-Standby R/A Type Power Connector

JPW2 12V DC Power

JSMBUS1 System Management Bus Header

JLAN1: LAN1/LAN2 LAN (RJ45) Ports

LVDS1 Dual Channel 48-bit LVDS Connector

USB4/5 Back Panel Universal Serial Bus (USB) 3.0 Ports

USB0/1, USB2/3 USB 2.0 Headers

USB6 USB 3.1 Type-C Header

VGA Back Panel VGA Port

15

Chapter 1: Introduction

Note: The table above is continued on the next page.

Motherboard Features

CPU

• A2SAN-H/-E, A2SAN-H/-E-WOHS: Intel® Atom™ x5-E3940 Processor, Quad Core, 2M Cache, 1.6GHz-1.8GHz, 9.5W

• A2SAN-L, A2SAN-L-WOHS: Intel® Atom™ x5-E3930 Processor, Dual Core, 2M Cache, 1.3GHz-1.8GHz, 6.5W

• X11SAN, X11SAN-WOHS: Intel® Pentium® Processor N4200, Quad Core, 2M Cache, 1.1GHz-2.5GHz, 6W

Memory

• Integrated memory controller supports DDR3L 1333/1600/1866MHz Non-ECC 204-pin SO-DIMM up to 8GB

DIMM Size

• Single channel DDR3L 1333/1600/1866MHz Non-ECC 204-pin SO-DIMM up to 8GB

Expansion Slots

• One (1) Full Mini-PCI Express slot (USB2.0 x 1, PCIe Gen2 x 1)

• One (1) M.2 2280 B-Key for SATA or PCIe SSD (2242/3042 B-key M.2 module is supported by an extender bracket - P/N:

MCP-290-00161-0N)

Network

• Dual GbE LAN with Intel® Ethernet Controller I210

Graphics

• Intel® HD Graphics GT Series

• Features: OpenGL 5.0, DirectX 12, OpenCL 2.1

• Hardware Decode: AVC/H.264, MPEG2, VC1/WMV9, JPEG/MJPEG,

HEVC/H.265, VP8, VP9, MVC

• Hardware Encode: AVC/H.264, JPEG/MJPEG, HEVC/H.265, VP8, VP9, MVC

• Display: VGA (resolution up to 2560x1600 at 60Hz), HDMI 1.4 (resolution up

to 3840x2160 at 30Hz), LVDS (dual channel 48-bit, resolution up to 1920x1080

at 60Hz)

I/O Devices

• COM Ports

• Four (4) front accessible ports (JCOM1 supports two RS232/RS422/RS485,

JCOM2/3 supports two RS232)

• SATA Ports • One (1) SATA 3.0 port (I-SATA1)

• Audio Header • One (1) HD Audio header with Mic-in/Headphone-out (Realtek ALC888S)

• SMBus Header • One (1) SMBus box header

• Speaker • One (1) Speaker header

Peripheral Devices

• Two (2) USB 3.0 ports on the rear I/O panel (USB4/5, Type A)

• Four (4) USB 2.0 headers (USB 0/1, USB2/3, Pin Header)

• One (1) USB 3.1 header on the rear I/O panel (USB6, Type C)

Motherboard Features

16

Super A2SAN-H/-E/-L and X11SAN User's Manual

Motherboard Features

BIOS

• 128Mb SPI AMI BIOS

®

• ACPI 3.0 or later, SMBIOS 2.7 or later, PCI F/W 3.0, BIOS rescue hot-key, RTC (Real Time Clock) wakeup

Power Management

• ACPI power management

• S3, S4, S5

• Power button override mechanism

• Power-on mode for AC power recovery

• Wake-On-LAN

• TXE Management Engine

• Force Power On by Jumper

• RTC Battery (typical voltage: 3.0V, normal discharge capacity: 220mAh)

System Health Monitoring

• Onboard voltage monitoring for +1.35V, +12V, +3.3V, +5V, 3.3V standby, System level control, System temperature,

VBAT, VCGI

• CPU switching phase voltage regulator

• CPU thermal trip support

Fan Control

• 4-pin fan headers

System Management

• Trusted Platform Module (TPM) 2.0 support

• SuperDoctor® 5, Watch Dog, RoHS

LED Indicators

• Power/Suspend-state indicator LED

Mehcanical Specication

• Dimensions: 4" (L) x 5.75" (W) (102mm x 146mm) SBCs

• Height: A2SAN-H/-L 33mm, A2SAN-E 42mm, X11SAN 32mm, A2SAN-H/-E/-L-WOHS 29.05mm

Environment

• Operating Temperature Range: A2SAN-E/-L, A2SAN-E/-L-WOHS, and A2SAN-H-WOHS support -30°C ~ 75°C (-22°F ~

167°F). X11SAN, X11SAN-WOHS, and A2SAN-H support 0°C ~ 60°C (32°F ~ 140°F)

• Non-Operating Temperature Range: -40°C - 85°C (-40°F - 185°F)

• Operating Relative Humidity Range: 8% - 90% (non-condensing)

• Non-Operating Relative Humidity Range: 10% - 95% (non-condensing)

Note 1: The CPU maximum thermal design power (TDP) is subject to chassis and

heatsink cooling restrictions. For proper thermal management, please check the chas-

sis and heatsink specications for proper CPU TDP sizing.

17

Chapter 1: Introduction

Note: This is a general block diagram and may not exactly represent the features on

your motherboard. See the previous pages for the actual specications of your moth-

erboard.

Figure 1-6.

System Block Diagram

USB 3.0

Intel

DDR3L non ECC SKU

DUAL CHANNEL

MAX. 8G SO-DIMM SUPPORTED

DDR3L 1866 MHz

Non-ECC-SODIMM0

DDI0

HDMI connector

SATA[1]

USB 3.0 [0]

SPI

FLASH

SPI 128Mb

FST_SPI

USB 2.0 [0]

High Definition

REALTEK

ALC888S-VD2-GR

FRONT AUDIO Header

I/O PANEL LAYOUT

USB 3.0

M.2 SLOT (B KEY)

USB 3.0 [1]

Rear USB3.0 connector (USB 0)

Rear USB3.0 connector (USB 1)

5.0Gb/s

USB 2.0 [1]

DDI1

SATA

6Gb/s

MUX

USB 2.0 [2]

USB 2.0 [7]

USB 2.0 [3]

USB 2.0 [4]

USB 2.0 [5]

480Mb/s

LPC

SIO

Port 80 / Debug header

NCT6106D

Audio

SATA 6Gb/s

I-SATA0

SATA[0]

eDP

VGA

Rear USB2.0 Header (USB 3)

Rear USB2.0 Header (USB 2)

CH7517

DP to VGA Bridge

VGA Connector

PTN3460

DP to LVDSBridge

LVDS Connector

480Mb/s

Front USB2.0 Header (USB 4)

Front USB2.0 Header (USB 5)

COM 3 / 4 (RS232)

PCIe Gen2 x 1

5.0GT/s

PCIE[0]

GLAN1

INTEL I210

PCIe Gen2 x 1

5.0GT/s

PCIE[2]

RJ45

GLAN2

INTEL I210

RJ45

PCIe Gen2 x 1

PCIE[1]

5.0GT/s

PCIe Gen2 x 1

5.0GT/s

PCIE[3]

Mini-PCIe Slot

PCIe Gen2 x 2

5.0GT/s x2

PCIE[4/5]

ASM1142

PCIe Gen2 X2 to USB3.1

TYPE C

480Mb/s

LAN 1

21

TYPE C

USB 3.1

HDMI

LAN 2

COM 1 / 2 (RS232/RS422/RS485)

USB 2.0

480Mb/s

COM 5 / 6 (RS232)

18

Super A2SAN-H/-E/-L and X11SAN User's Manual

Figure 1-7.

A2SAN/X11SAN Series Specication Chart

1

X11SAN/A2SAN Series Spec Chart

*Note: Audio codec operating temperature 0-60C only. Onboard TPM operating temperature -20~75C.

Model CPU

Base

Freq

Turbo

Freq

CPU

TDP

GbE VGA HDMI LVDS RS-232

RS-

232/422/4

85

USB3.0 USB2.0 USB3.1 24V out GPIO Audio

TPM

2.0

Temp.

Passive

Heatsink

A2SAN-H

E3940

(QC)

1.6GHz 1.8GHz 9.5W 2 Yes Yes Yes 2 2 2 4 1 N/A 8-bit Yes Yes 0-60C

SNK-

C0103L

20mm

A2SAN-L

E3930

(DC)

1.3GHz 1.8GHz 6.5W 2 Yes Yes Yes 2 2 2 4 N/A N/A 8-bit Yes N/A -30-75C

SNK-

C0103L

20mm

A2SAN-E

E3940

(QC)

1.6GHz 1.8GHz 9.5W 2 Yes Yes Yes 2 2 2 4 N/A N/A 8-bit Yes Yes -30-75C

SNK-

C0107L

29mm

X11SAN

N4200

(QC)

1.1GHz 2.5GHz 6W 2 Yes Yes Yes 2 2 2 4 1 N/A 8-bit Yes Yes 0-60C

SNK-

C0103L-1

19mm

A2SAN-H-

WOHS

E3940

(QC)

1.6GHz 1.8GHz 9.5W 2 Yes Yes Yes 4 2 2 4 N/A Yes 8-bit Yes Yes -30-75C N/A

A2SAN-L-

WOHS

E3930

(DC)

1.3GHz 1.8GHz 6.5W 2 Yes Yes

Yes 2 2 2 4

N/A N/A 8-bit Yes N/A -30-75C N/A

A2SAN-E-

WOHS

E3940

(QC)

1.6GHz 1.8GHz 9.5W 2 Yes Yes Yes 2 2 2 4 N/A N/A 8-bit Yes Yes -30-75C N/A

X11SAN-

WOHS

N4200

(QC)

1.1GHz 2.5GHz 6W 2 Yes Yes Yes 2 2 2 4 1 N/A 8-bit Yes Yes 0-60C N/A

Note 1: Audio codec operating temperature 0-60C only. Onboard TPM operating tem-

perature -20~75C.

Note 2: -WOHS models do not include a heatsink. Purchase a Supermicro standard

passive heatsink or provide your own thermal solution.

19

Chapter 1: Introduction

1.2 Processor Overview

Built upon the functionality and capability of the Intel® Atom SoC series processor, the

A2SAN-H/-E/-L and X11SAN motherboard offers maximum I/O expandability, energy

efficiency, and data reliability in a 14-nm process architecture, and is optimized for

embedded storage solutions, networking applications, or cloud-computing platforms. The

A2SAN-H/-E/-L and X11SAN drastically increases system performance for a multitude of

server applications.

The A2SAN-H/-E/-L and X11SAN supports the following features:

• Intel Virtualization Technology for Directed I/O (Intel VT-d)

• Enhanced Intel SpeedStep® Technology

• Video Connectors: VGA, HDMI, and LVDS

• USB3.1 Gen 2 Type-C (Only supported on X11SAN and A2SAN-H)

• Adaptive Thermal Management/Monitoring

• Mini-PCI-E slot with PCIe Gen2 x1 with transfer rates of up to 5Gb/s

• Gen3 SATA ports with transfer rates of up to 6Gb/s

• System Management Bus (SMBus) Specication, Version 2.0

• M.2 slot with B-key 2280/2242/3042 module is supported by an extender bracket

• TPM2.0 (Trusted Platform Module) onboard with Disable/Enable jumper (not supported on

A2SAN-L)

• Integrated Sensor Hub (ISH)

• Intel® Identity Protection Technology

1.3 Special Features

This section describes the health monitoring features of the A2SAN-H/-E/-L and X11SAN

motherboard. The motherboard has an onboard System Hardware Monitor chip that supports

system health monitoring.

20

Super A2SAN-H/-E/-L and X11SAN User's Manual

Recovery from AC Power Loss

The Basic I/O System (BIOS) provides a setting that determines how the system will respond

when AC power is lost and then restored to the system. You can choose for the system to

remain powered off (in which case you must press the power switch to turn it back on), or

for it to automatically return to the power-on state. See the Advanced BIOS Setup section

for this setting. The default setting is Last State.

Note: Before setting the Recovery from AC Power Loss function in the BIOS, please

adjust force power on jumper JPF1 to pins 2-3 to disable the force power-on function.

1.4 ACPI Features

ACPI stands for Advanced Conguration and Power Interface. The ACPI specication denes

a exible and abstract hardware interface that provides a standard way to integrate power

management features throughout a computer system including its hardware, operating system

and application software. This enables the system to automatically turn on and off peripherals

such as network cards, hard disk drives and printers.

In addition to enabling operating system-directed power management, ACPI also provides a

generic system event mechanism for Plug and Play and an operating system-independent

interface for conguration control. ACPI leverages the Plug and Play BIOS data structures

while providing a processor architecture-independent implementation that is compatible with

Windows® 10.

1.5 Power Supply

As with all computer products, a stable power source is necessary for proper and reliable

operation. It is even more important for processors that have high CPU clock rates. In areas

where noisy power transmission is present, you may choose to install a line lter to shield

the computer from noise. It is recommended that you also install a power surge protector to

help avoid problems caused by power surges.

1.6 Super I/O

The Super I/O (NCT6106D chip) provides four high-speed, 16550 compatible serial

communication ports (UARTs), one of which supports serial infrared communication. Each

UART includes a 128 byte send/receive FIFO, a programmable baud rate generator, complete

modem control capability and a processor interrupt system. UARTs provide legacy speed with

baud rate of up to 115.2 Kbps as well as an advanced speed with baud rates of 250 K, 500

K, or 1 Mb/s, which support higher speed modems.

Page is loading ...

Supermicro A2SAN-H-WOHS User manual

This manual is also suitable for

Supermicro A2SAN-H-WOHS User manual

Related papers

Other documents