Reese 118339 Installation guide

Reese
Brand
Reese
Model
118339
Type
Installation guide

This manual is also suitable for

Reese 118339

Below you will find brief product information for Reese 118339. This device is a T-connector adapter used to connect a vehicle's tail light wiring harness to enable towing a trailer. The adapter has a 4-amp capacity per circuit and comes with a grommet and screw for installation. With this adapter, you can easily connect your vehicle's electrical system to a trailer's lighting system, allowing you to use the trailer's lights, turn signals, and brake lights while towing.

Reese 118339

Below you will find brief product information for Reese 118339. This device is a T-connector adapter used to connect a vehicle's tail light wiring harness to enable towing a trailer. The adapter has a 4-amp capacity per circuit and comes with a grommet and screw for installation. With this adapter, you can easily connect your vehicle's electrical system to a trailer's lighting system, allowing you to use the trailer's lights, turn signals, and brake lights while towing.

A
B
ENGLISH
1. Locate the vehicle's tail light
wiring harness by removing the large
rubber grommet (A) underneath the
vehicle on the left (driver's) side,
between the rear wheel and bumper.
The harness will be attached to the
back side of the grommet.
2. Insert the T-connector adapter into
the harness connector and lock into
place. Be sure that the connector is
fully inserted with locking tabs in
place.
3. Insert the vehicle grommet &
connectors into the hole in the body
panel and seal the hole with the
grommet supplied with the
T-connector adapter (B).
4. Route the T-connector harness to
the center of the vehicle and secure
the black box to the vehicle with the
screw and cable tie provided.
5. Test the installation with a test
light or trailer
This unit is rated for 4 amps per
circuit.
ESPAÑOL
1. Para localizar el cableado de la luz
trasera del vehículo remueva el gran
ojete de goma (A) que se encuentra
debajo del vehículo, en el lado
del pasajero, entre la llanta trasera y
la defensa. El cableado se encontrará
unido a la parte trasera del ojete.
2. Inserte la conexión en T en el
conector del cableado y asegúrelo
firmemente. Asegúrese de que el
conector en T esté completamente
insertado y de que las orejetas de
seguridad cumplan su función de
mantener la conexión unida
fijamente.
3. Inserte el ojete del vehículo y los
conectores dentro del agujero del
panel del vehículo y selle el agujero
con el ojete que se suple junto con el
conector en T (B).
4. Encamine el cableado de la
conexión en T hacia el centro del
vehículo y asegure la caja negra al
vehículo usando el tornillo y el
amarre plástico que se provee.
5. Pruebe la instalación usando una
luz de prueba o un remolque.
Esta unidad es clasificada para 4
amperios por el circuito.
FRANÇAIS
1. Pour localiser le faisceau de fils
des feux arrière du véhicule, retirez le
grand passe-fil (A) d'en dessous du
véhicule du côté gauche (conducteur),
entre la roue arrière et le pare-chocs.
Le faisceau est attaché derrière le
passe-fil.
2. Insérez l’adaptateur du connecteur
en T au connecteur du faisceau et
serrez-le en place. Assurez-vous que
le connecteur soit inséré à fond et
que les languettes de retenue soient
en place.
3. Insérez le passe-fil du véhicule et
les connecteurs à travers le trou du
panneau de la carrosserie et fermer
le trou avec le passe-fil fourni avec
l'adaptateur du connecteur en T (B).
4. Acheminez le faisceau du connecteur
en T au centre du véhicule et attachez
la boîte noire au véhicule utilisant la
vis et le collier de serrage fournis.
5. Utilisez une lampe témoin ou une
remorque pour vérifier que l'installa-
tion est correcte.
Cette inité est évaluéé pour 4
ampères par circuit.
Installation instructions
Instructions d’installation
Instrucciones de instalación
18339-037 1/16/01
  • Page 1 1

Reese 118339 Installation guide

Reese
Brand
Reese
Model
118339
Type
Installation guide
This manual is also suitable for

Reese 118339

Below you will find brief product information for Reese 118339. This device is a T-connector adapter used to connect a vehicle's tail light wiring harness to enable towing a trailer. The adapter has a 4-amp capacity per circuit and comes with a grommet and screw for installation. With this adapter, you can easily connect your vehicle's electrical system to a trailer's lighting system, allowing you to use the trailer's lights, turn signals, and brake lights while towing.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents