Chicago Electric 93633 Operating instructions

Brand: Chicago Electric

Model: 93633

Type: Operating instructions

Chicago Electric 93633 is a booster cable with an inline tester. This device can be used to jump start a vehicle or test a vehicle's battery or alternator.

To jump start a vehicle, attach the red battery clamps to the positive battery terminals of both vehicles. Attach one black battery clamp to the negative battery terminal of the donor vehicle and the other black battery clamp to an unpainted, solid piece of metal on the vehicle with the dead battery. Start the donor vehicle's engine and allow it to idle. Turn the ignition switch of the vehicle with the dead battery to “START” for no more than 5 to 6 seconds. If the vehicle's engine does not start, turn the ignition switch to “OFF” and wait at least 3 minutes before repeating this step. When finished, turn off both vehicles and remove the booster cable.

Chicago Electric 93633 is a booster cable with an inline tester. This device can be used to jump start a vehicle or test a vehicle's battery or alternator.

BOOSTER CABLE

WITH INLINE TESTER

OPERATING INSTRUCTIONS

3491 Mission Oaks Blvd., Camarillo, CA 93011

Visit our Web site at: http://www.harborfreight.com

2005 by Harbor Freight Tools

may be reproduced in any shape or form without the express written consent of Harbor Freight Tools.

For technical questions, please call 1-800-444-3353.

SAVE THESE INSTRUCTIONS

1. Use eye protection. Always wear ANSI approved safety

impact eye goggles when using this product.

2. Maintain a safe working environment. Always keep the

work area free of obstructions, grease, oil, trash, and other

debris. Do not use this product in areas near flammable chemi-

cals, dust, and vapors.

3. Read and understand all instructions and safety pre-

cautions as outlined in the manufacturer’s manual of

the vehicle with which this product will be used.

4. Never allow the red and black Battery Clamps to touch

each other or the same metal object.

5. WARNING! Lead acid batteries generate hydrogen gas dur-

ing normal operation, and even more gas is generated when

the battery is charging. Hydrogen gas is explosive.

SAFETY WARNINGS AND PRECAUTIONS

#93633

OPERATING INSTRUCTIONS

To jump start a vehicle:

1. Make sure the transmissions of both vehicles are in “PARK”

and their emergency brakes have been set. Also, turn off the

engine of the “donor” vehicle prior to connecting the Booster

Cable to the batteries of both vehicles.

2. Attach the RED/POSITIVE (+) Battery Clamps to the POSI-

TIVE battery terminals of both vehicles.

3. Attach one BLACK/NEGATIVE (–) Battery Clamp to the NEGA-

TIVE battery terminal of the “donor” vehicle. Attach the other

BLACK/NEGATIVE (–) Battery Clamp to an unpainted, solid

piece of metal on the vehicle with the “dead” battery.

4. Start the “donor” vehicle’s engine and allow to idle.

5. Turn the ignition switch of the vehicle with the “dead” battery

to “START” for no more than 5 to 6 seconds. NOTE: If the

vehicle’s engine does not start, turn the ignition switch to “OFF”

and wait at least 3 minutes before repeating this Step. When

finished, turn off both vehicles and remove the Booster Cable.

NOTE: NO REPLACEMENT PARTS ARE AVAILABLE FOR THIS PRODUCT.

ALTERNATOR

(RED-LIGHTS UP IF WORKING CORRECTLY)

BATTERY

(GREEN-LIGHTS UP IF HIGHLY CHARGED)

BATTERY

(YELLOW-LIGHTS UP IF BATTERY O.K.)

BATTERY

(RED-LIGHTS UP IF BATTERY LOW)

RED/POSITIVE (+) BATTERY CLAMP

TO POSITIVE BATTERY TERMINAL

BLACK/NEGATIVE (–) BATTERY CLAMP

TO NEGATIVE BATTERY TERMINAL

RED/POSITIVE (+) BATTERY CLAMP

TO NONCONDUCTIVE OBJECT

BLACK/NEGATIVE (--) BATTERY CLAMP

TO NONCONDUCTIVE OBJECT

REVERSE HOOKUP

(RED-LIGHTS UP IF BOOSTER CABLE

NOT

CONNECTED PROPERLY)

Made in China.

12/05

6. WARNING! If battery fluid comes in contact with skin, wash

with soap and water and rinse with lemon juice and vinegar.

If the fluid comes into contact with eyes, flush with water for

several minutes and contact a physician immediately. Never

burn a battery as it can explode in a fire. Do not attempt to

charge a leaking battery.

7. WARNING! People with pacemakers should consult their

physician(s) before using this product. Electromagnetic fields

in close proximity to a heart pacemaker could cause interfer-

ence or failure of the pacemaker. In addition, people with

pacemakers should adhere to the following: Caution is nec-

essary when near the coil, spark plug wires, or distributor of

a running engine.

To test a vehicle’s battery/alternator:

1. Attach one RED/POSITIVE (+) Battery Clamp to the POSI-

TIVE battery terminal of the vehicle. Then, insulate the re-

maining RED/POSITIVE (+) Battery Clamp by clamping it to

nonconductive

object, i.e., a piece of dry wood.

2. Attach one BLACK/NEGATIVE (–) Battery Clamp to the NEGA-

TIVE battery terminal of the vehicle. Then, insulate the re-

maining BLACK/NEGATIVE (–) Battery Clamp by clamping

it to a

nonconductive

object, i.e., a piece of dry wood.

3. Observe the LED display lights to determine the condition of

the battery. (See below.)

4. Start the vehicle, and observe the LED display light to deter-

mine the condition of the alternator. (See below.)

5. When finished, turn off the vehicle’s engine. Disconnect the

Booster Cable from the battery and nonconductive objects.

Then, store the Booster Cable in a clean, dry, safe location out

of reach of children.

Chicago Electric 93633 Operating instructions

Brand: Chicago Electric

Model: 93633

Type: Operating instructions

Chicago Electric 93633 is a booster cable with an inline tester. This device can be used to jump start a vehicle or test a vehicle's battery or alternator.

Download PDF

report

Chicago Electric 93633 Operating instructions

Chicago Electric 93633 Operating instructions

Related papers

Other documents