Wolf I543418 Installation Instructions Manual

Brand: Wolf

Model: I543418

Category: Cooker hoods

Type: Installation Instructions Manual

This manual is also suitable for

Wolf I543418, a 54-inch wide island hood, efficiently removes smoke, grease, and odors from the air while you cook. Equipped with halogen lighting, it brightens your cooking surface for better visibility. The hood features a Heat Sentry that automatically adjusts blower speed to manage heat levels. Its stainless steel body with a brushed finish adds a touch of elegance to your kitchen.

RO S ERIES

I SLAND H

OODS I NSTALLATION

I NSTRUCTIONS

I MPORTANT I NFORMATION

IMPORTANT NOTE: This appliance

must be installed in accordance with

National Electrical Codes, as well as

all state, municipal and local codes.

The correct voltage, frequency and

amperage must be supplied to the

appliance from a dedicated, ground-

ed circuit which is protected by a

properly sized circuit breaker or time

delay fuse. The proper voltage,

frequency, and amperage ratings are

listed on the product rating plate.

Record the model and serial numbers

before installing the island hood.

Both numbers are listed on the rating

plate, located on the left island of

hood shell.

Model #

Serial #

If you have questions concerning the

installation of this product, call Wolf

Appliance Company, LLC at (800)

332-9513.

If you received a damaged island

hood you should immediately contact

your dealer or builder.

IMPORTANT NOTE: This

installation must be completed by a

qualified installer or service agency.

Before you begin installation, read

these instructions completely and

carefully.

• INSTALLER: please retain these

instructions for local inspector’s

reference, then leave them with the

homeowner.

• Please read the entire installation

instructions prior to installation.

• HOMEOWNER: please read and

keep these instructions for future

reference.

• Please read the entire Wolf

Pro Series Ventilation Use & Care

Information book prior to use.

As you follow these installation

instructions, take particular note of

the CAUTION and WARNING

symbols when they appear. This

information is important for the safe

and efficient installation of the Wolf

Pro Series island hood.

In addition, the printed instructions

may signal an IMPORTANT NOTE,

which highlights information that is

especially important for a problem-

free installation.

CAUTION

signals a situation where minor

injury or product damage may

occur if you do not follow

instructions.

WARNING

states a hazard that may cause

serious injury or death if pre-

cautions are not followed.

P RO S ERIES I SLAND H OOD I NSTALLATION

ISLAND HOOD FEATURES

• Available in 36", 42", 54" and 66"

widths (91mm, 1066mm, 1371mm and

1676mm.)

• (R) models include mounting holes

for optional decorative rail

• Recessed controls

• Halogen lighting with night-light setting

• Hand finished with continually

welded seams

• Stainless steel enclosed liner

• Stainless steel baffle filters

• Internal or remote blower option

• Heat Sentry feature

• 16-gauge stainless steel shell

• Transition with backdraft damper included

• Optional decorative rail assembly in stain-

less, platinum, brass or copper finish.

Hood

must be specifically preordered and con-

figured for rail assembly.

Island Hood Overall Dimensions-see below specs

34"

(864 mm)

(C)

(D)

Center of hood-back of hood

(B)

Width of hood dimension

(A)

Width of top plate dimension

Center of transition

side of hood

Island Width top Width of Height of To center of To center of

Hood plate hood transition transition of hood

(side of hood) (back of hood)

I363418 18” 36” 8.75” 9” 6.5”

I423418 24” 42” 8.75” 12” 6.5”

I543418 36” 54” 8.75” 18” 6.5”

I663418 48” 66” 8.75” 24” 6.5”

INSTALLATION

CONSIDERATIONS

1) A straight, short duct run will

allow the hood to perform more effi-

ciently. Try to limit the number of

elbows and transitions to as few as

possible. Long duct runs, elbows and

transitions will reduce the perform-

ance of the hood.

IMPORTANT NOTES:

All hoods must exhaust to the out-

doors. There is a possibility of noise

issues, if there is a short duct run

coupled with a remote blower.

2) Always use metal ducting. Do not

use flex ducting.

3) Wolf recommends installing a

back-draft damper in all installations

(included with hood). In cold weather

installations a back-draft damper is

necessary to minimize the backflow

of cold air into the room.

4) Wolf recommends the hood be

installed 30”-36” above the cooking

surface.

5) Local building codes may require

the use of make-up air. Consult your

local HVAC professional for specific

requirements in your area.

P RO S ERIES I SLAND H OOD P RE-INSTALLATION

Island hood installation

CAUTION

To reduce the risk of fire and

electric shock, install this range

hood only with the blowers

manufactured by Wolf

Appliance Co., Model numbers

801640, 801642, 801641,

804701, 804703 and 801642.

Shipping Weights for Blowers

Part Shipping

Blower Number Weight

CTBLOWER-60REM

801640 35 lbs.

CTBLOWER-90REM

801641 35 lbs.

CTBLOWER-120REM

801642 39 lbs.

CTBLOWER-150REM

804701 47 lbs.

IBLOWER-120INT

804703 38 lbs

Hood Hardware Contents:

• (4) 1/4” x 3” lag screws

Part number 805666

• (8-16) #10 x 2” hex self-tapping

screws. (qty varies per hood)

Part number 805667

• Extra Hardware Screw Set

Part number 805669

18" (457)

HEIGHT

OF HOOD

34" (864)

DEPTH OF HOOD

36" (914)

WIDTH OF HOOD

30" TO 36"

(762 - 914)

TO COOKING

SURFACE

COOKING SURFACE

LOCATION OF ELECTRICAL

CENTERED THROUGH TOP OF HOOD

30" TO 36"

(762 - 914)

TO COOKING

SURFACE

Dimensions may vary by +_ 1/8" (3 mm).

Dimensions in parentheses are in millimeters.

RO S ERIES I

SLAND H OOD I NSTALLATION

Shipping Weights for Island Hoods

Model Number Shipping Weight

I363418 88 lbs.

I423418 96 lbs.

I543418 116 lbs.

I663418 137 lbs.

CAUTION

A minimum of three installers is

required to lift island hood into

position.

HOOD PREPARATION

IMPORTANT NOTE:

If installing a duct cover, the duct

cover must be installed prior to hood

installation. See page #10 for duct

cover installation instructions or fol-

low those packed with duct cover.

1) Remove hood filters from hood

shell.

2) Remove center filter bank by

removing the 2 screws from each

side. DO NOT DISCARD THESE

PARTS, as they will be reinstalled after

hood installation is complete.

3) The hood assembly is shipped with

the transition attached. The transition

is shipped upside down in the top of

the hood assembly and must be

removed and reinstalled.

4) Detach the transition from the

hood assembly by removing the (4)

screws on the top of the hood assem-

bly. DO NOT DISCARD SCREWS.

Shipping screws are needed for the

reinstallation of the transition to

hood.

5) Invert transition so that the 10”

round points away from top of hood.

Use screws removed from step 4.

6) If installing a remote blower, drill

7/8” hole through framing for con-

duit wiring. See Internal Blower on

page 8 for overall dimensions and

electrical requirements. See installa-

tion instructions provided with the

blower for mounting and installation

information.

IMPORTANT NOTE: Do not run or

remove blower electrical connections

through duct work.

INSTALLATION

Install Ductwork

1) Decide where the ductwork will

run between the hood and the

outside of the home. Your Wolf island

hood has a top discharge which will

run vertically.

IMPORTANT NOTE: All hoods must

exhaust to the outdoors.

2) When not installing an external

ventilator, always install a roof or

island cap. Connect 10" round metal

ductwork to the cap and work back

towards the hood location.

3) Use duct tape to seal the joints

between the ductwork sections.

4) Your Wolf island hood comes stan-

dard with a 10" round transition with

backdraft damper. It is recommended

that a backdraft damper be used in

all installations.

IMPORTANT NOTE: Do not use duct

smaller than 10".

WARNING

To reduce the risk of fire, use

only metal ductwork.

Island Hood Top Transition

P RO S ERIES I SLAND H OOD I NSTALLATION

Removing Island Hood Filter Bank

INSTALL HOOD

1) Make sure there is at least a 10"

opening in the ceiling to accommo-

date the duct work necessary for

proper ventilation.

2) Layout the overall dimensions of

the hood top plate on the finished

ceiling or unfinished surface. The top

plate width is 13", but overall length

will vary with the size of the hood.

Refer to the overall dimensions illus-

tration on page 3.

3) Use 2 x 4’s to construct the fram-

ing. The weight of the hood makes

proper structural support necessary.

4) Mark the center location of the

hood. Install (2) 2 x 4’s across the top

of the ceiling joists.

5) Drill 5/32" holes in 2 x 4’s to

match the pattern of the top of the

hood.

6) Make sure hood filters and hood

filter bank are removed prior to

installation of hood. See page 6 for

direction.

7) Lift the hood and align hood

mounting holes with pre-drilled ceil

ing holes. Slide ⁄" lag screws through

hood mounting holes and tighten

into 2x4 framing. DO NOT OVER

TIGHTEN SCREWS.

8) Connect the 10" round ductwork

to the hood transition using sheet

metal screws or duct tape.

9) Make electrical connections. See

Install Wiring on page 8.

10) Adjust hood to proper location

and tighten all 4 lag screws until

hood surface is flush with ceiling.

Install #10 x 2" screws through

remaining hood mounting holes

along top edge of hood surface for

additional support.

11) If installing internal blower DO

NOT REINSTALL hood filters and

hood center filter bank until blower

installation is complete. See Internal

blower installation on page 8.

P RO S ERIES I SLAND H OOD I NSTALLATION

Typical top view of installation

TOP OF

ISLAND HOOD

EXISTING

CEILING JOISTS

2 X 4's

DUCT

Distance will vary

depending on hood

size (see pg 3)

10" ROUND

1/4" x 3"

Lag Screws

13"

CAUTION

Framing must be structurally

tied together and tied to ceiling

joists to provide enough

strength to support the weight

of the hood and the internal

blower, if applicable.

CAUTION

A minimum of three installers is

required to lift island hood into

position.

INSTALL THE WIRING

This ventilation hood must be pro-

perly grounded, This unit should be

installed by a qualified electrician in

accordance with all applicable

national and local codes.

IMPORTANT NOTE: Do not run or

remove blower electrical connections

through duct work.

1) Run 120 VAC, 15 AMP minimum

circuit electric power cable from the

service panel to the junction box at

the center of hood. Supply 20”

minimum of Romex wire.

2) Remove the knockout located on

the left side of the hood top plate.

See below illustrations for specific

location and dimensions of knockout.

3) Feed the conduit through the hole

on top of the hood to junction box

located in center of hood shell.

4) Remove the junction box cover

and connect black to power supply

black wire, white to power supply

white wire and green wire to green

or bare wire.

5) Place all wiring connections inside

junction box and re-install cover.

Make sure that all wires are secure

and that no wires are pinched

between cover and box.

Island Hood Top Transition

WARNING

Before servicing or cleaning

unit, switch power off at service

panel and lock the service dis-

connecting means to prevent

power from being switched on

accidentally. When the service

disconnecting means cannot be

locked, securely fasten a promi-

nent warning device, such as a

tag, to the service panel.

P RO S ERIES I SLAND H OOD I NSTALLATION

INTERNAL BLOWER

IMPORTANT NOTE: Before turning

the power on, make sure the blower

is in the "OFF" position. Use wire con-

nectors or wire nuts approved by UL

or C/UL. Refer to installation instruc-

tions provided with each blower to

verify island or roof cut-outs.

IBLOWER-120REM (804703)

Installation

1) Remove hood filter and centerfil-

ter bank from hood. See page 6 for

instructions

2) Lift ventilator into position inside

the hood.

3) Engage two (2) Tabs on Ventilator

into two (2) Slots in Top of Hood.

Secure ventilator to Threaded Studs

with two (2) Hex Nuts (provided.)

4) Plug ventilator's power cords into

receptacles inside the hood. Be sure

to secure power cords with clips on

hood interior so as not to damage

during operation of blower.

5) Replace filters and center filter

bank once blower installation is com-

plete. See page 6 for direction.

WARNING

HEX NUTS

THREADED

STUDS

TOP OF

HOOD

POWER

CORDS

RECEPTACLES

TAB

SLOT

VENTILATOR

Internal Ventilator Blower

0.875" (22 mm)

(Electrical)DIA. HOLE

RECTANGULAR HOLE

5.875" x 8"

(149 mm x 203 mm)

Wiring Diagram:

Refer to the wiring diagram pack-

aged with the hood for more

information.

(A) Dimension in from

left side of hood

(B) dimension back

from front of hood to

center of knock-out

Hood Size

36" (914mm)

1" (25mm)

42" (1067mm) 2" (51mm)

1 1/2" (38mm)

54" (1372mm)

8" (203mm) 1 1/2" (38mm)

Island Hood Electrical Knockout Location

Island Hood Electrical Knockout Dimensions

REMOTE BLOWER

IMPORTANT NOTE: Before turning

the power on, make sure the blower

is in the "OFF" position. Use wire con-

nectors or wire nuts approved by UL

or C/UL. Refer to installation instruc-

tions provided with each blower to

verify island or roof cut-outs.

STEP 1: Plan the Installation

1) Locate the blower so the length of

the duct run and number of elbows

and transitions are kept to a mini-

mum.

2) Where possible, blower should be

located between island studs or roof

rafters.

3) Avoid pipes, wires or other duct-

work that may be running through

the island.

4) Be sure that there is enough space

for any transitions that may be need-

ed between the blower and the con-

necting ductwork.

5) For best performance, locate tran-

sitions nearest the blower.

STEP 2: Connect Remote Blower

NOTE: Always refer to all blower

installation instructions provided with

the blower for additional mounting

and wiring instructions.

1) Remove cover from wiring box

inside of hood shell. Remove wiring

box knockout.

2) Feed 20” of inbound (Romex)

power cable through the knockout

opening hole and into the wiring

box. Secure the cable to wiring box

with an appropriate connector for

type of cable being used. Connect

leads as follows:

• Black (L1) to black (loose) in the J

box from the switch.

•Neutral to neutral (loose) in the J

box from the switch.

3) Wiring Remote Blower: Follow

wiring instructions at the blower as

outlined in the particular blower

installation instructions. Black (L1) to

black, white (neutral) to white – or

white to blue, or white to brown

(depending on model) and green to

grounding screw. Run remote blower

cable (ROMEX) to the hood.

Feed 20”of (ROMEX) power cable

through the knockout opening hole

and into the wiring box on the

rough-in plate of hood. Secure the

cable to wiring box with an appropri-

ate connector.

Locate cord assembly provided with

the remote blower. The cord assem-

bly has two leads, black (L1) and

white (neutral). Connect these leads

to the leads from the blower, black to

black and white to white.

Connect ALL green and bare wires

together to the ground screw in the

wiring box.

4) Plug cord assembly into receptacle

located near the center of the hood

shell. Use clips on hood interior to

keep excess power cord away from

moving parts.

5) Re-install wiring box cover and

screws. Make sure all wires are secure

and that no wires are pinched

between cover and box.

"(622)

"(394)

"(717)

"(527)

"(629)

14"(356)

"(121)

10"(254)

DIAMETER

Remote blower dimensions – 600 CFM (801640) and

900 CFM (801641)

10"(254)

DIAMETER

"(375)

"(749)

18"(457)

22"(559)

"(257)

"(184)

10"(254)

Remote blower dimensions – 1200 CFM

(801642)

10"(254)

DIAMETER

"(375)

"(749)

21"(533)

25"(635)

"(264)

"(181)

10"(254)

Remote blower dimensions – 1500 CFM

(804701)

P RO

S ERIES I

SLAND H OOD I NSTALLATION

INSTALL DUCT COVER

1) Duct cover must be installed to

ceiling prior to hood installation

2) Use (4) ⁄" x 3" lag screws provided

with hood to attach duct cover to ceil-

ing frame work. See page 3 for addi-

tional dimension information.

3) Install additional #10 x 2" screws

for support along top edge of duct-

cover and ceiling.

4) Install (4) 5/16" bolts, provided

with duct cover, through hood

mounting holes into bottom edge of

duct cover. Use 5/16" nuts supplied

with duct cover and tighten on bolts.

Use #12 x 7/8" hex head self tapping

screws provided with duct cover to

attach duct cover to hood assembly

P RO S ERIES I SLAND H OODS I NSTALLATION

INSTALL HOOD FILTER

AND DRIP CUPS

Hood Filters and Drip Cups Install

1) Reinstall hood filter center bank

with screws removed prior to installa-

tion of hood assembly.

2) Remove all packaging material

from filters and drip cups.

3) Slide drip cups along bottom edge

of hood opening so lip overhangs

slightly.

4) Lift filters into place. Lines of fil-

ters must run vertically and align with

drip cups.

5) Adjust filters to fill space by sliding

filters left to right.

CAUTION

Installing a duct cover assembly

will impact all aspects of hood

installation including hood loca-

tion, ducting, electrical place-

ment and adequacy of mounting

surfaces.

INSTALL LOGO

The nameplate is not pre-assembled

because there are various locations that

the logo can be installed. Additionally,

some customers prefer not to have a

nameplate on their hood. For your

convenience, Wolf has created a tem-

plate for a standardized logo location.

Please see the back page of these

installation instructions for Wolf logo

template.

1) Decide on the location for the

nameplate.

2) Clean mounting area with rubbing

alcohol.

3) If desired, cut-out template for

nameplate location.

4) Fold template, locate placement on

hood and tape to hood surface.

5) Check alignment and adjust if nec-

essary.

6) Remove backing paper from name-

plate.

7) Position nameplate in template

cutout and press into place.

8) Remove template and any tape

residue.

OPTIONAL

DUCT

COVER

1/4" x 3" Lag Screw

5/16" SS Nut

5/16" SS Screw

#1/4" x 7/8" #12

self-tapping hex screw

2" #10 hex screw

Duct cover installation

DUCT COVERS

Stainless steel duct covers are avail-

able in 6 and 12 inches for all Wolf

island hoods.

6-inch Duct Covers for Island Hoods

• DUC6COVER36I – 6" duct cover for

36" island hoods.

• DUC6COVER42I – 6" duct cover for

42" island hoods.

• DUC6COVER54I – 6" duct cover for

54" island hoods.

• DUC6COVER66I – 6" duct cover for

66" island hoods.

12-inch Duct Covers for Island

Hoods

• DUC12COVER36I – 12" duct cover

for 36" island hoods.

• DUC12COVER42I – 12" duct cover

for 42" island hoods.

• DUC12COVER54I – 12" duct cover

for 54" island hoods.

• DUC12COVER66I – 12" duct cover

for 66" island hoods.

P RO S ERIES I SLAND H OOD A CCESSORIES

BLOWERS

Internal Blowers

• IBLOWER-120INT (804703) –

1200 CFM internal blower for island

hoods.

See blower and cooking product

chart for recommendations.

External Blowers

• CTBLOWER-60REM (801640) –

600 CFM external blower for island

hoods (36", 42" and 54" wide).

• CTBLOWER-90REM (801641) –

900 CFM external blower for island

hoods (36", 42" and 54" wide).

• CTBLOWER-120REM (801642) –

1200 CFM blower for island hoods.

• CTBLOWER-150REM (804701) –

1500 CFM blower for island hoods.

See blower and cooking product

chart for recommendations.

P RO S ERIES I SLAND H OOD A CCESSORIES

DECORATIVE RAIL

ASSEMBLIES

Decorative rail assemblies are available

for Wolf island hoods in stainless steel,

platinum, brass and copper finishes.

Hood must be specifically ordered and

configured for rail assembly. Assembly

includes rail, standoffs and mounting

hardware.

Stainless Steel Finish:

• RAIL-36/SS – Decorative rail for 36"

island hoods.

• RAIL-42/SS – Decorative rail for 42"

island hoods.

• RAIL-54/SS – Decorative rail for 54"

island hoods.

• RAIL-66/SS – Decorative rail for 66"

island hoods.

Platinum Finish:

• RAIL-36/PLT – Decorative rail for 36"

island hoods.

• RAIL-42/PLT – Decorative rail for 42"

island hoods.

• RAIL-54/PLT – Decorative rail for 54"

island hoods.

• RAIL-66/PLT – Decorative rail for 66"

island hoods.

Brass Finish:

• RAIL-36/BR – Decorative rail for 36"

island hoods.

• RAIL-42/BR – Decorative rail for 42"

island hoods.

• RAIL-54/BR – Decorative rail for 54"

island hoods.

• RAIL-66/BR – Decorative rail for 66"

island hoods.

Copper Finish:

• RAIL-36/COP – Decorative rail for 36"

island hoods.

• RAIL-42/COP – Decorative rail for 42"

island hoods.

• RAIL-54/COP – Decorative rail for 54"

island hoods.

• RAIL-66/COP – Decorative rail for 66"

island hoods.

SERVICE

INFORMATION

IMPORTANT NOTE: If the island

hood does not operate properly,

follow these troubleshooting steps:

• Verify that power is being supplied

to the island hood.

• Check the electrical connections to

ensure that the installation has been

completed correctly.

• If the island hood still does not

work, contact an authorized Wolf

Factory Authorized Service Center. Do

not attempt to repair the appliance

yourself. Wolf is not responsible for

service required to correct a faulty

installation.

• To obtain the name and number of

a Wolf Factory Authorized Service

Center, call Wolf Customer Service at

(800) 332-9513 or check our website;

www.wolfappliance.com.

• When calling for service, you will

need the island hood model and seri-

al numbers. Both numbers are listed

on the rating plate, located on the

left island of hood shell.

I MPORTANT I NFORMATION

The information and images are the copyright property of Wolf Appliance Company, LLC,

an affiliate of Sub-Zero Freezer Company, Inc. Neither this book nor any information or images

contained herein may be copied or used in whole or in part without the express written permission

of Wolf Appliance Company, LLC, an affiliate of Sub-Zero Freezer Company, Inc.

WOLF LOGO TEMPLATE

Use the full-scale template on the

following page 14 when placing the

nameplate in the standardized Wolf

logo location.

CUT-OUT FOR LOGO PLACEMENT

BOTTOM EDGE OF HOOD

FOLD LINE FOR LOGO PLACEMENT

LEFT OUTER EDGE OF HOOD

Wolf Appliance Company, LLC

P.O. Box 44848 • Madison, WI 53744 • 800-332-9513

www.wolfappliance.com

805050 7/03

Wolf I543418 Installation Instructions Manual

Brand: Wolf

Model: I543418

Category: Cooker hoods

Type: Installation Instructions Manual

This manual is also suitable for

Download PDF

report

Wolf I543418 Installation Instructions Manual

This manual is also suitable for

Wolf I543418 Installation Instructions Manual

Related papers

Other documents