Wonwoo EWSJ-223 Installation & Operating Manual

Category
Security cameras
Type
Installation & Operating Manual

This manual is also suitable for

18, 22, 26, 27, 33, 36, 37x
Outdoor High Speed Dome Camera
P/N : 388065120
PRINTED IN KOREA
Distributed by
EWSJ-E180, EWSJ-E260, EWSJ-E360, EWSJ-E361
EWSJ-270, EWSJ-330, EWSJ-331, EWSJ-370, EWSJ-371
EWSJ-363,EWSJ-223
INSTALLATION / OPERATING MANUAL
Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use
Wall In-Ceiling Ceiling
02
EWSJ Series Outdoor Speed PTZ Dome Camera System Use's Guide
03
EWSJ Series Outdoor Speed PTZ Dome Camera System Use's Guide
1. 1 Important Safety Instruction
Read these instructions.
Pay attention on all the warnings.
Follow all instructions.
Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
Do not dissemble or insert foreign objects.
Do not install near any heat sources such as radiation, beat registers, stoves, or other apparatus.
(Including amplifiers) that produce heat.
Do not aim the camera at the sun or any other strong light source.
Do not install the camera in intermittent lighting environments.
Only use attachments/accessories specified by the manufacturer.
Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution when moving the cart/apparatus combination
to avoid injury from tip-over.
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or
objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.
Installation should be done only by qualified personnel and conform to all local codes.
Installation should be done in a place strong enough to hold it.
Use only installation methods and materials capable of supporting four times the maximum specified load.
It is designed for indoor use only and it must not be installed where exposed to rain and moisture
without additional outdoor housing and bracket.
To prevent damage from water leakage when installing a mount outdoors on a roof or wall,
apply sealant around the bolt holes between the mount and mounting surface.
These instructions are for use by qualified service personnel only. To reduce the risk of electric shock
do not perform any servicing other that contained in the operating instructions unless you are qualified
to do so.
Only use replacement parts recommended by manufacturer.
ad these instructions.
1. PRECAUTIONS
TABLE OF CONTENTS
3p.
4p.
4p.
5p.
6p.
7p.
8p.
10p.
12p.
13p.
13p.
14p.
14p.
16p.
18p.
19p.
19p.
22p.
25p.
34p.
35p.
36p.
47p.
47p.
48p.
48p.
49p.
50p.
51p.
1. PRECAUTIONS
1. 1 Important Safety Instruction ...................................................................................
2. GETTING STARTED
2. 1 Descriptions ..........................................................................................................
2. 2 Unpacking ..............................................................................................................
2. 3 EWSJ Series Selection Flow ...................................................................................
2. 4 EWSJ Series (Outdoor Speed PTZ Dome Camera ) Module .....................................
2. 5 EWSJ Series Accessories Selection (Sold Separately) ............................................
2. 6 DIP Switch Setting .................................................................................................
2. 7 Cable Connection ...................................................................................................
3. INSTALLATION (Indoor / Wall / Ceiling)
3. 1 Indoor (In-Ceiling) ..................................................................................................
3. 2 Wall Mounting ........................................................................................................
3. 3 Ceiling Mounting ....................................................................................................
4. ON-SCREEN DISPLAY PROGRAM MENU
4. 1 Powering ON ..........................................................................................................
4. 2 Establishing Camera Control ...................................................................................
4. 3 Motion Menu ..........................................................................................................
4. 4 Dome Menu ...........................................................................................................
4. 5 Camera Menu ........................................................................................................
4. 5. 1 CAMERA 1 Setting (EWSJ-270, 330, 331, 370, 371) .....................................
4. 5. 2 CAMERA SETTING (EWSJ-E180, E260, E360, E361) .....................................
4. 5. 3 Camera Menu (EWSJ-223, 363) ....................................................................
4. 5. 4 Clear Menu ....................................................................................................
5. SPECIFICATION
5. 1 Mechanism Specification .......................................................................................
5. 2 Camera Specification..............................................................................................
6. DIMENSION
6. 1 EWSJ Series .........................................................................................................
6. 2 Wall and Ceiling Bracket (WB-300 / CPA-301) ........................................................
6. 3 PMB-600(Parapet Mount Bracket) .........................................................................
6. 4 CMA-100(Corner Mount / PMA-100(Pole Mount) ...................................................
7. CONFIGURATION
7. 1 Control from Keyboard WTX-2000 or DVR ..............................................................
7. 2 Connecting to WTX-1200A with DVR ......................................................................
7. 3 Connecting to WTX-1200A with DVR ......................................................................
04
EWSJ Series Outdoor Speed PTZ Dome Camera System Use's Guide
05
EWSJ Series Outdoor Speed PTZ Dome Camera System Use's Guide
2. 3 EWSJ Series Selection Flow2. 1 Descriptions
The Dome Supremacy EWSJ series are an outdoor speed PTZ dome system designed for IP66 applications,
especially, whether it is raining, snowing or sunny day, this EWSJ series delivers superior performance.
The EWSJ series is one unit of housing with pole, corner, wall or recessed ceiling mounts. It includes a high
resolution color camera; video output capability through coaxial cable; pan/tilt control using Pelco D or P
protocol with on-screen programming.
2. 2 Unpacking
The following parts are supplied with the EWSJ series outdoor speed PTZ dome system.
1. Dome drive
2. Dome body (housing)
3. Dome cover (bubble with trim ring)
4. Wall-mount bracket or Ceiling-mount bracket (one of two)
5. Interface cable with two wired wiper on one end and BNC female on the other end(In-ceiling only)
6. User’s Guide
7. Self-tapping screws
2. GETTING STARTED
2. 3. 1
Indoor
2. 3. 2
Outdoor
Outdoor Corner & Pole Mount EWSJ outdoor type and WB-300 and
ISB-100 and CMA-100 or PMA-100
Model Select Mount Type
Model Select Mount Type
Indoor Wall mount EWSJ outdoor type and
WB-300 and ISB-100
EWSJ outdoor type and
CPA-301(300mm) or
CPA-351(500mm)
Outdoor Parapet mount EWSJ Outdoor type
and PMB-600
Model Select Mount Type
Model Select Mount Type
Indoor ceiling mount
Model Select
In-ceiling mount EWSJ-FC
Mount Type
<Figure 1. package Components>
Dome Drive
Bracket (Wall or Ceiling) Cable & Wire(In-Ceiling only) User’s Guide Screws
Dome Body (Housing) Dome Cover Connectors
06
EWSJ Series Outdoor Speed PTZ Dome Camera System User’s Guide
07
EWSJ Series Outdoor Speed PTZ Dome Camera System User’s Guide
2. 5 EWSJ Series Accessories Selection (Sold Separately)2. 4 EWSJ Series (Outdoor Speed PTZ dome camera) Module
2.4. 1 EWSJ Series (Outdoor Speed PTZ dome camera) Models
EWSJ-270: 1/4” Sony Super HAD CCD, Optical 27x
EWSJ-330: 1/4” Sony Super HAD CCD, Optical 33x
EWSJ-331: 1/4” Sony Interline Dual Scan CCD, Optical 33x with WDR
EWSJ-370: 1/4” Sony Super HAD CCD, Optical 37x
EWSJ-371: 1/4” Sony Interline Dual Scan CCD, Optical 37x with WDR
EWSJ-E180: 1/4” Sony Ex-view CCD, Optical 18x
EWSJ-E260: 1/4” Sony Ex-view CCD, Optical 26x with Image Stabilizer
EWSJ-E360: 1/4” Sony Ex-view CCD, Optical 36x
EWSJ-E361: 1/4” Sony Interline Dual Scan CCD, Optical 36x with WDR
EWSJ- 363: 1/4" Sony Super HAD II (Double Scan )CCD, Optical 36x with WDR
EWSJ- 223: 1/4" Sony Super HAD II (Double Scan )CCD, Optical 22x with WDR
- WDR feature works in EWSJ-331, EWSJ-371, EWSJ-E361,EWSJ-363 and EWSJ-223 model only.
IMPORTANT> When placing order, please make sure of which the below optional selection for the default
camera package is proper for your application.
- Optional 1: Smoke dome cover / Clear dome cover
- Optional 2: PAL type / NTSC type (E.g. EWSJ-331P/EWSJ-331N)
- Optional 3: Including Wall-mount bracket or including Ceiling-mount bracket
IMPORTANT> Smoke dome cover let others be unaware of where the camerae is shooting.
The camera performance is likely to be the same using either smoke or transparent clear
cover orslightly darker with smoke cover. If you don't want others know where you are
shooting, then choose the smoke cover.
WB-300
- In case the camera contains
Wall-mount bracket as standard
- Aluminum body
- Unit: 1Kg
- Cool gray color
WPA-301
CPA-301 (300mm)
CPA-351 (500mm)
ITEM Model Name Image Description
PMB-600
- Stainless steel(SUS) body
- Unit : 5.2Kg
- Silver color
- Maximum load : 20Kg
- Dimensions : 890x650 (Arm)
- 250 x 350 (Mount plate)
CMA-100
PMA-100
ISB-100
- Steel body
- Unit : 0.4Kg
- Cool gray color
- In case the camera contains
Wall-mount bracket as standard
- Steel body (CPA-301: 300mm)
- Unit : 1.6Kg(CPA-301)
- Cool gray color
- Steel body
- Unit : 1.3Kg
- Cool gray color
- Steel body
- Unit : 0.7Kg
- Cool gray color
- Aluminum body
- Unit : 5Kg
- Silver color
- In case the camera contains
Wall-mount bracket as standard
- Aluminum body
- Unit: 3.1Kg
- Cool gray color
EWSJ-FC
In-ceiling mount
housing
Wall Bracke
Wall Plate
Pipe Adaptor
Ceiling Plate
Pipe Adaptor
Parapet mount
bracket
Corner Mounting
Adaptor
Pole mounting
Adaptor
Installation Box
08
EWSJ Series Outdoor Speed PTZ Dome Camera System User’s Guide
09
EWSJ Series Outdoor Speed PTZ Dome Camera System User’s Guide
SW204
123
off off off
off off on
off on off
off on on
on off off
on off on
on on off
on on on
WTX
WPD
WPP
ADP
nc
nc
nc
nc
Protocol SW204, SW205
412
off off off
off off on
off on off
off on on
on off off
on off on
on on off
on on on
2400
4800
9600
19200
38400
57600
115200
230400
Baudrate(bps)
SW205
34
off off
off on
on off
on on
none
even
odd
nc
Parity
SW206
12
off off
off on
on off
on on
SDM
nc
EM
FCB
Cam type
SW206
3
off
on
NTSC
PAL
NTSC/PAL
SW206
4
off
on
422
485
RS-422/485
x100
SW201
x10
SW202
x1
SW203
ADDRESS
(SW201, SW202, SW203)
(SW204, SW205, SW206)
2. 6. 2 Set the termination On/Off
(SW601)
2. 6 DIP Switch Setting
2. 6. 1 Dip Switch Setting
Before start up the dome camera, set the protocol and camera address and termination set with
dip-switches and click-switches as shown in the below diagram.
Termination Switch
(SW601)
Setting Switch
(SW204, SW205, SW206)
Address Switch
(SW201, SW202, SW203)
SW201 SW202 SW203
SW204 SW205 SW206
SW601
1 2 3 4
ON
1 2 3 4
ON
1 2 3 4
ON
1 2
The device which is connected at the end of the line must have the cable communication
terminated. Without proper termination, there is potential for control signal errors.EWSJ series
have the cable communication terminated by setting the appropriate dip switch as below.
1: On 2: On ' Terminated
2: Off 3: Off ' Not terminated
2. 6. 3 Set the camera address (ID)
2. 6. 4 Set the details fo the dome
S201: 100-digit number of address (ID)
S202 : 10-digit number of address (ID)
S203 : 1-digit number of address (ID)
Ex) If SW203=8, SW202=2, SW201=1,
the ID number is 128
S204 #1~#3 : Protocol setup
S204 #4, S205 #1,2 : Communication speed setup
S205 #3, #4 : Parity setup
S206 #1, #2 : Camera Setup
S206 #3 : NTSC, PAL Setup
S206 #4 : Communication(RS-422/485)
10
EWSJ Series Outdoor Speed PTZ Dome Camera System User’s Guide
11
EWSJ Series Outdoor Speed PTZ Dome Camera System User’s Guide
2. 7 Cable connection
COM A
N.C A
N.O A
GND
ALARM4
ALARM3
ALARM2
ALARM1
AC 24V
AC 24V
COM B
N.C B
N.O B
GND
ALARM8
ALARM7
ALARM6
ALARM5
ALARM PORT_A ALARM PORT_B
R(T)X A
R(T)X B
TX A
TX B
GND
AC 24V
AC 24V
F GND
CAM POWER RS485 / RS422
HEATER
2. 7. 2 RS-485/RS-422 Connection
2. 7. 1 Power/Data communication cable connection
2. 7. 4 Alarm connection
RS-422/485 connection
EWSJ series can be remotely controlled by an external device or control system, such as a control
keyboard or DVR, using RS-485 half-duplex, RS-422 duplex or simplex serial communication signals.
Connect marked RX+, RX- to TX+ and TX- of the RS-485 control system.
If control system is RS-422, connect TX+,TX- of controller to RX+ and RX- of the EWSJ series. And
also connect the TX+, TX- of EWSJ to RX+, RX- of the control device respectively. Total length of
the cable for communication should not exceed 1.2Km.
2. 7. 3 Video Output connection
Connect the video out (BNC) connector to the monitor or video input of DVR. Video cable and
RS-485/422 communication cable are not provided in this product's package.
Power connection
- Connect the power of AC 24V, 1000mA to this dome camera.
- Use certified / Listed Class 2 power supply transformer only.
- Please be sure for AC input for camera and AC input for Fan & Heater.
- Power Terminal: 3PIN
- Com Terminal: 5PIN
(Controller)
(PTZ)
12
EWSJ Series Outdoor Speed PTZ Dome Camera System User’s Guide
13
EWSJ Series Outdoor Speed PTZ Dome Camera System User’s Guide
3.Installtion (Indoor / Wall / Ceiling)
3. 1 Indoor (In-Ceiling)
①②
①②
①②
- The following steps of installation and connection work should be done by qualified service personnel
or system installers and should conform to all local codes.
- Be sure to switch the camera off before installation is completed.
- Do not install the camera near the air outlet of an air conditioner.
- Before installation, set the dome system with Dip switch on the back side of the mechanism part, and
assemble the mechanism and housing according to the below instruction
Unpack the dome package and take out the dome drive, dome body (housing), dome cover
(bubble with trim ring) and other components. Insert the dome drive to the dome body and
connect the cables as shown in the above diagram.
Assemble the dome cover to the dome body by pressing the cover gently downward to the
dome body with two hands on the side of the cover. Do not press the cover with strong pressure.
This might cause damage to the dome body.Screw the dome cover and body together.
Need for additional in-ceiling mount housing, EWSJ-FC. Refer to the page of 2.3 Products sold
separately for the detail. Make a hole in the ceiling to install the camera and prepare for the wire
with connector.For easy installation, screw the three safety screws slightly.
For the safety reason, turn off the main power during the installation.
Connect the wire to the in-ceiling mount housing assembled dome system.
Put the dome system into the ceiling hole.
Fasten the safety wire to the ceiling
Do not press the dome cover with too strong pressure while putting the dome system into
the ceiling hole. It can cause serious damage onto the surface of the dome cover bubble
3. 2 Wall Mounting
Insert the dome drive to the dome body and connect the cables as shown in the above diagram.
Assemble the dome cover to the dome body by pressing the cover gently downward to the
dome body with two hands on the side of the cover. Do not press the cover with strong pressure.
This might cause damage to the dome body.Screw the dome cover and body together.
Install the bracket on to the wall to install the camera and prepare for the wire with connector.
For easy installation, screw the three safety screws slightly.For the safety reason, turn off the
main power during the installation. Connect the cable with the assembled dome system.
Put the dome system into the bracket. Fasten the 3 installation screws as shown in the above
diagram.
3. 3 Ceiling Mounting
Insert the dome drive to the dome body and connect the cables as shown in the above diagram.
Assemble the dome cover to the dome body by pressing the cover gently downward to the
dome body with two hands on the side of the cover. Do not press the cover with strong pressure.
This might cause damage to the dome body.Screw the dome cover and body together.
Make a hole in the ceiling to install the camera and prepare for the wire with connector.
For easy installation, screw the three safety screws slightly.For the safety reason, turn off the
main power during the installation. Connect the cable with the assembled dome system.
Put the dome system into the bracket.
Fasten the 3 installation screws as shown in the above diagram.
14
EWSJ Series Outdoor Speed PTZ Dome Camera System User’s Guide
15
EWSJ Series Outdoor Speed PTZ Dome Camera System User’s Guide
4. 1 Powering On
When turning EWSJ series camera power on, there is a ten (10) second pause before the camera starts
its homing phase. During the homing phase the camera pans left and right and tilts up and down. It also
adjusts the lens focus.
4. 2 Establishing Camera Control
The most common way to interface with the camera is using a keyboard and on-screen display (OSD)
menu. This method is the most common and is covered in this manual.
4. 2. 1 Basic Keyboard Operation
The following tables summarize the basic operations for a standard keyboard and the functions available
to control EWSJ series.
Table 1. 1 Typical Keyboard Functions
Table 2. 1 Typical Keyboard Controls for EWSJ series speed PTZ dome camera system
4. ON-SCREEN DISPLAY PROGRAM MENU
Typical Keyboard Features Usage
Function Keys
Number Keys
Camera Key
Enter Key
Focus Key (Or Near Key)
Iris Key
Key LEDs
LCD
Joystick
Selects a specific control setting
Inputs a number from 0 to 9.
Selects a camera number
Inputs a selection
Sets the lens focus or make a menu selection in OSD menu.
Sets the lens iris setting or makes a menu selection in OSD mode.
Indicates an active key
Displays the current status
Controls a pan/tilt/zoom (PTZ) EWSJ series
Dome Operation How to Control
To Pan Side to Side
To Tilt Up and Down
To Zoom In
To Zoom Out
Move the joystick left or right.
Move the joystick forward and back.
Twist the joystick clockwise.
Twist the joystick counterclockwise.
EWSJ series is programmed through the on-screen display (OSD) menus.
To access the OSD menus, you must open the main Setup Menu.
4. 2. 3 Setup Program OSD Menu From Keyborad.
The main Setup Menu provides access to all programmable EWSJ series settings.
4. 2. 2 Keyboard Commands
- Keyboard control commands are composed of a sequence of two (2) inputs with the following
convention: 1) a Command number key(s) + 2) a Function key.
- Command numbers range from 1 to 999.
- Refer to the keyboard manual for the key naming conventions in detail.
4. 2. 4 Go into the camera setup 0SD Menu
Press key “1” and keep pressing the “MENU” key for approximately 3 seconds, or press key “95” and
press “Preset” key to go into the set-up menu. Setup menus are shown in the diagram below. You can
adapt the camera to your requirements by setting up the respective items in these menus.
4. 2. 5 OSD Menu tree
MAIN MENU
MOTION
DOME
CAMERA
CLEAR
PTZ RESET
EXIT
< NEAR / RIGHT ▷ MOTION >
MOTION MENU
PRESET
TOUR
SCAN
PATTEN
AREA
PRIVACY
BACK EXIT
< NEAR / RIGHT ▷ PRESET >
DOME MENU
TITLE :
POWER UP ACTION
PARK ACTION
DISPLAY ON / OFF
SPEED BY ZOOM
AUTO FLIP
FACTORY SET
SAVE BACK EXIT
< NEAR / RIGHT ▷ TITLE >
: ON
: ON
: ON
CAMERA MENU
FOCUS
D-ZOOM
WHITE BAL
BACKLIGHT
EXPOSURE
DAY / NIGHT
IRIS SET
DIS MODE
NEXT SAVE BACK EXIT
< NEAR / RIGHT ▷ FOCUS >
: AUTO
: ON
: OFF
: COLOR
CLEAR MENU
PRESET
TOUR
SCAN
PATTEN
AREA
ALARM
PRIVACY
BACK EXIT
< NEAR / RIGHT ▷ PRESET >
16
EWSJ Series Outdoor Speed PTZ Dome Camera System User’s Guide
17
EWSJ Series Outdoor Speed PTZ Dome Camera System User’s Guide
4. 3 Motion Menu
4. 3. 1 PRESET
- Function : Max. 255 positions can be stored as Preset position. The preset number can be assigned
from 1 to 255, but 95 is reserved for starting OSD menu. Camera characteristics
(i.e. White Balance, Auto Exposure) except for Focus can be set up independently for each
preset. Label can be freely set to the each Preset position. All characteristic can be set up
in OSD menu.
- Preset No. : Max. 255 positions can be stored and the each position can be assigned as a defined
Preset No.
- Label : Each Preset can have its own label name.
- Position : It displays the coordinates to position the assigned Preset.
- Focus : It enables to set the camera focus for each Preset position. (Default Auto)
4. 3. 2 TOUR
- Function :
By using Tour function, you can make camera to move among Max. 15 Preset positions
repeatedly. When Tour function runs, camera moves from the preset assigned as the 1st
point to the preset assigned as the last point in sequence. The camera will stay to the each
point for the time set to the dwell time in Tour Edit and move to the next point.
- Tour No. :
Max. 8 Tours can be stored and the each tour can have Max. 15 Preset positions with defined
Tour No.
- Label : Each Tour can have its own label name.
- Tour Edit : The Preset position, Speed and Dwell time can be assigned to the each Tour. The Speed
can be set up from 1°/sec to 63°/sec and the Dwell time can be set up from 1sec to 99sec.
4. 3. 3 SCAN
- Function :
By using Scan function, the camera moves between 2 positions if there is no PTZ command
after passing the assigned Dwell time. When there is no camera movement, the Scan function
runs and the camera moves from the position assigned as the start point to the position
assigned as the end point in CW(Clockwise) direction.
- Scan No. : Max. 8 Scans can be stored.
- Label : The each Tour can have its own label name.
- Start position : Assign the coordinate of the Scan starting position.
- End position : Assign the coordinate of the Scan ending position.
- Speed : It enables to set the running speed in the each coordinate.(1~63sec)
- Dwell : The Scan function runs after the Dwell time without any camera movement.(1~60 min)
- Focus : It enables to set the camera Focus. (Default is Auto)
MOTION MENU
PRESET
TOUR
SCAN
PATTEN
AREA
PRIVACY
BACK EXIT
< NEAR / RIGHT ▷ PRESET >
4. 3. 4 PATTERN
- Function :
Pattern function is that a camera memorizes the path (mostly curve path) by joystick of
controller for assigned time and revives the path exactly as it memorized.
- Pattern No. : 4 Patterns can be stored in Keyboard menu. But if by chance your Keyboard does not
have
this menu, then
the Pattern might not be performed correctly.
- Labe l: The each Pattern can have its own label name.
- Record :
Movement by joystick and preset movement can be memorized in a pattern. To save the recording,
press NEAR key. It records Max. 60seconds. If by chance your Keyboard is not set to WCY
model, then this Record menu might not be performed.
- Play : To revive the Pattern during the recorded time.
4. 3. 5 AREA
- Function :
By using Area function, you can make camera to move between 2 pan positions repeatedly.
When Area functions runs, camera moves from the pan position assigned as the start pan
position to the position assigned as the stop pan position. In case that the position assigned
as the start point is same as the position assigned as the end position, camera turns on its
axis by 360° in CW direction and then it turns on its axis by 360° in CCW direction.
- Area No. : Max. 16 Area can be stored.
- Label : The each Area can have its own label name.
- Start Pan Position : Assign the coordinate of Area starting position.
- Stop Pan Position : Assign the coordinate of Area stopping position.
4. 3. 6 ALARM
- Function :
Alarm function enables the camera move to the programmed Preset position when there is
Alarm trigger.
- Alarm No. : Max. 8 Alarms can be stored.
- Label : The each Alarm can have its own label name.
- Preset No. : Assign the Preset No. to run when alarm is triggered.
4. 3. 7 PRIVACY
- Function : To protect privacy, Max. 8 Privacy can be created on the arbitrary position to hide objects
such as windows, shops or private house. With spherical coordinates system, powerful
Privacy zone masking function is possible.
- Privacy No. : Max. 8 Privacy zone can be stored.
- Position : Assign the coordinate to hide with Privacy.
18
EWSJ Series Outdoor Speed PTZ Dome Camera System User’s Guide
19
EWSJ Series Outdoor Speed PTZ Dome Camera System User’s Guide
4. 4. 1 TITLE
- Function : Set the camera title to display on screen
- To store the Title, press TELE button on the Keyboard. To delete, press WIDE.
4. 4. 2 POWER UP ACTION
- Function :
This function enables to resume the last action executed before power down. Most of actions
such as Preset, Tour, Pattern, and Scan are available for this function but Jog actions are not
available to resume.
- To activate this function, set this function to ON.
4. 4. 3 PARK ACTION
- Function :
This function enables to locate the camera to specific position automatically if operator doesn’t
operate the controller for a while.
- Time<Min> : The Park time can be assigned from OFF and 10 to 120 seconds ( by 10 seconds).
- Function : Can select one of the motion functions, Preset, Tour, Pattern and Scan.
- Number : The number of selected motion function.
4. 4. 4 DISPLAY ON/OFF
- Function : It enables to turn on or off for the menu On-screen display.
-
TITLE, ALARM, ZOOM, POSITION, PRESET, ACTION, TOUR, SCAN, PATTERN, PRIVACY, and AREA menu
On-screen display On/Off
- To turn on the display, press TELE button from the Keyboard. To turn off, press WIDE.
4. 4. 5 SPEED BY ZOOM
- Function :
Pan and Tilt speed can be changed depending on zoom magnification. Tele will slow down
the speed of Pan/Tilt and Wide will increase the Pan/Tilt speed. It will take about 3.5min
for 1 cycle in Tele mode and about 1.5seconds in the Wide mode.
- Default is On.
4. 4. 6 AUTO FLIP
- Function :
In case that tilt angle arrives at the top of tilt orbit (90°), zoom module camera keep moving
to opposite tilt direction (180°) to keep tracing targets. As soon as zoom module camera
passes through the top of tilt direction (90°), images should be reversed automatically and
appears in screen. If this function is set to OFF, tilt movement range is 0~90°
-
You can observe the moving object without reversing of the screen, by using this AUTO FLIP function.
4. 4. 7 FACTORY SET
- Function : It makes to restore all of setting value to the factory default.
- Please be careful that all of existing value would be erased by this Factory Set ON.
4. 4 Dome Menu
DOME MENU
TITLE :
POWER UP ACTION
PARK ACTION
DISPLAY ON / OFF
SPEED BY ZOOM
AUTO FLIP
FACTORY SET
SAVE BACK EXIT
< NEAR / RIGHT ▷ TITLE >
: ON
: ON
: ON
4. 5 Camera Menu
FOCUS
In Focus menu, you can set up the focus mode among Auto, Manual or One Push.
select : or Set ON : Set OFF :
NEAR NEAR
select : or Set ON : Set OFF :
NEAR NEAR
select : or Set ON : Set OFF :
NEAR NEAR
select : or Set ON : Set OFF :
NEAR NEAR
WHTE BALANCE
White balance setting is a function revising color temperature to resolve the problem that screen’s colors
change
by the color temperature’s difference arrcording to time.
CAMERA MENU 1
FOCUS
D-ZOOM
WHITE BAL
BACKLIGHT
EXPOSURE
DAY/NIGHT
IRIS DET
DIS MODE
NEXT SAVE BACK EXIT
< NEAR / RIGHT ▷ FOCUS >
: AUTO
: ON
: OFF
: COLOR
: OFF
4. 5. 1 CAMERA 1 Setting (EWSJ-270, 330, 331, 370, 371)
WHITE BAL MENU
▷ AWB MODE
RED OFFSET
BLUE OFFSET
COLOR SETUP
SHARPNESS
BACK
< NEAR / RIGHT ▷ AWB MODE >
: OUTDOOR
: ---
: ---
: 50
: 08
- AWB MODE : Select AWB mode.
- RED,BLUE OFFSET : Adjust the brightness from 01 to 99.
It is available when the AWB MODE is in MENUAL
mode.
- COLOR SETUP : Adjust the brightness from 01 to99.
- SHARPNESS : Adjust the sharpness from 01 to 31.
Decide using of digital zoom function.
D-ZOOM: ON/ OFF
BACKLIGHT : Select the OFF, HIGH, MID or LOW .
20
EWSJ Series Outdoor Speed PTZ Dome Camera System User’s Guide
21
EWSJ Series Outdoor Speed PTZ Dome Camera System User’s Guide
select : or Set ON : Set OFF :
NEAR NEAR
select : or Set ON : Set OFF :
NEAR NEAR
select : or Set ON : Set OFF :
NEAR NEAR
select : or Set ON : Set OFF :
NEAR NEAR
select : or Set ON : Set OFF :
NEAR NEAR
DAY/LIGHT : Select AUTO, COLOR or BW.
EXPOSURE MENU
▷ BRIGHTNESS
SHUTTER MODE
SHUTTER SPD
AGC
SSNR
SENS-UP MODE
SENS LIMIT
BACK
< NEAR / RIGHT ▷ BRICHTNESS >
: 50
: ESC
: ---
: MID
: MID
: AUTO
: X4
- BRIGHTNESS : Select brightness from 01 to 99.
- SHUTER MODE : Select ESC,ANTI F or MANUAL.
- SHUTER SPD : Select shuter speed from 1/12000 to X128.
- AGC : Select OFF,LOW,MID or HIGH.
- SSNR : Select OFF,LOW,MID or HIGH.
- SENS-UP MODE : Select AUTO or OFF .
- SENS LIMIT : Select from X2 to X128.
EXPOSURE
DIS MODE : Select ON or OFF.
EXPOSURE MENU
▷ BRIGHTNESS
SHUTTER MODE
SHUTTER SPD
AGC
SSNR
SENS-UP MODE
SENS LIMIT
BACK
< NEAR / RIGHT ▷ BRICHTNESS >
: 50
: ESC
: ---
: MID
: MID
: AUTO
: X4
- IRIS MODE : Select AUTO or MANUAL.
- IRIS VALUE : If you set the MODE in MENUAL, the value can be set
from 00 to 99.
IRIS SET
CAMERA MENU 2
LINE LOCK
WDR ON/OFF
WER LIMIT
WDR LEVE
LENS INIT
FACTORY
BACK
< NEAR / RIGHT ▷ FOCUS >
: ON
CAMERA MENU 2
LINE LOCK
PHASE VALUE
BACK
< NEAR / RIGHT ▷ FOCUS >
: ON
:
PHASE VALUE : Select EXT menu.
WDR ON/OFF (EWSJ-331, 371 only) : Select ON or OFF and set the LEVEL and the LIMIT value.
WDR LIMIT/LEVEL (EWSJ-331, 371 only)
: Select LOW - MIDDLE - HIGH and set the LEVEL from 00 to 100.
LENS INIT : Select YES or NO.
FACTORY : Select YES or NO.
CAMERA 2 FUNCTIONS
- Select NEXT in the bottom of CAMERA MANU 1.
LINE LOCK : Select INT or EXT.
22
EWSJ Series Outdoor Speed PTZ Dome Camera System User’s Guide
23
EWSJ Series Outdoor Speed PTZ Dome Camera System User’s Guide
select : or Set ON : Set OFF :
NEAR NEAR
select : or Set ON : Set OFF :
NEAR NEAR
select : or Set ON : Set OFF :
NEAR NEAR
WB MODE : Select AUTO, INDOOR, OUTDOOR ONEPUSH,
ATW, MANUAL or ONEPUSHTRG.
RED GAIN: Adjust red color level from 0~255.
(Standard level is 028)
BLUE GAIN: Adjust blue color level from 0~255.
(Standard level is 162)
* You can change the GAIN in the Manual.
FOCUS
In Focus menu, you can set up the focus mode Auto, Manual, One Push or INFINITY.
Decide using of digital zoom function.
D-ZOOM: ON/ OFF
select : or Set ON : Set OFF :
NEAR NEAR
select : or Set ON : Set OFF :
NEAR NEAR
select : or Set ON : Set OFF :
NEAR NEAR
BACKLIGHT : Select ON or OFF.
AUTO FOCUS MENU
▷ AF MODE
SENSITIVITY
BACK
< NEAR / RIGHT ▷ AF MODE SEL >
: NORMAL
: NORMAL
- AF MODE : Select NORMAL, ZOOM or INTERVAL.
- SENSITIVITY : Select NORMAL or LOW.
AF MODE
CAMERA MENU
FOCUS MODE
NEAR LIMIT
D-ZOOM
AF SETTING
WB SETTING
AE SETTING
BACK LIGHT
SPECIAL
SAVE BACK EXIT
< NEAR / RIGHT ▷ FOCUS MODE >
: AUTO
: 9.5CM
: ON
: OFF
4. 5. 2 CAMERA SETTING (EWSJ-E180, E260, E360, E361)
NEAR LIMIT :Infinity focus is the state where a lens forms an image of an object an infinite distance away.
This corresponds to the point of focus for parallel rays. ( Over Infinity~ 1.0CM)
WHITE BALANCE MENU
▷ WB MODE
RED GAIN
BLUE GAIN
BACK
< NEAR / RIGHT ▷ WB MODE SEL >
: AUTO
: XXX
: XXX
WB MODE
AUTO EXPO MENU
▷ AF MODE
EXPOSURE
SLOW SHUTTER
SHUTTER
IRIS LEVEL
BRIGHT LEVEL
GAIN
WDR ON/OFF
BACK
< NEAR / RIGHT ▷ AF MODE SEL >
: AUTO
: OdB
: AUTO
: AUTO
: AUTO
: XX
: XX
: OFF
- AE MODE : Select AUTO,MANUAL,SHUTTER,IRIS or BRIGHT.
- EXPOSURE : Set the value from 10.5dB to -10.5dB.
(Standard value is 0dB)
- SLOW SHUTTER : Select AUTO or MANUAL.
- SHUTTER : If you set SHUTTER in AE MODE, you can set the
SHUTTER value.
- IRIS LEVEL : If you set IRIS in AE MODE, you can set the IRIS
LEVEL from CLOSE to F1.6.
- BRIGHT LEVEL : If you set BRIGHT in AE MODE , .you can set
the LEVEL from 00 ~31
- GAIN : Set the value from -3dB to 28dB.
- WDR ON/OFF : Select ON or OFF (EWSJ-E361 only)
AE MODE
24
EWSJ Series Outdoor Speed PTZ Dome Camera System User’s Guide
25
EWSJ Series Outdoor Speed PTZ Dome Camera System User’s Guide
D-ZOOM (Digital Zoom)
- Magnification of the Digital Zoom can be switched On and Off.
- It is recommended that the Digital Zoom should be set up before the preset operation.
- As the digital zoom magnification increases, the image quality is lowered.
ZOOM MODE
FOCUS MODE
AE MODE
WB MODE
ICR MODE
SPECIAL
CAM RESET
< NEAR / RIGHT ▶ ZOOM SET >
SAVE BACK EXIT
CAMERA MENU
ZOOM MENU
ZOOM SPD : USER
D-ZOOM : ON
BACK
< NEAR / RIGHT
ZOOM SPEED>
ZOOM MENU
ZOOM SPD : USER
D-ZOOM : ON
BACK
< NEAR / RIGHT
D-ZOOM >
select : or Set ON :
Set OFF :
NEAR
NEAR
select : or Set ON :
Set OFF :
NEAR
NEAR
ZOOM SPD : Select from 1sept to 7 steps,
USER (Standard speed)
Decide using of digital zoom function.
D-ZOOM: ON/ OFF
ZOOM MODE
Zoom speed can be set and decide using of digital
zoom function.
select : or Set ON : Set OFF :
NEAR NEAR
SPECIAL MENU
▷ DAY/NIGHT
LINE LOCK
V-PHASE
CAMERA RESET
BACK
< NEAR / RIGHT ▷ AE MODE >
: AUTO
: INT
: ---
- DAY/NIGHT : Select AUTO, OFF, DAY or NIGHT.
- LINE LOCK : Select INT or EXT.
- V-PHASE : Select EXT in LINE LOCK and set the value.
- CAMERA RESET : Make initialize the setting value which is set in
CAMERA MENU.
SPECIAL 4. 5. 3 Camera Menu (EWSJ-223, 363)
26
EWSJ Series Outdoor Speed PTZ Dome Camera System User’s Guide
27
EWSJ Series Outdoor Speed PTZ Dome Camera System User’s Guide
FOCUS
In Focus menu, you can set up the focus mode among Auto, One Push or Manual.
CAMERA MENU
ZOOM MODE
FOCUS MODE
AE MODE
WB MODE
ICR MODE
SPECIAL
CAM RESET
SAVE BACK EXIT
< NEAR / RIGHT
FOCUS SET >
select : or Set ON :
Set OFF :
NEAR
NEAR
select : or Set ON :
Set OFF :
NEAR
NEAR
AUTO: The camera adjusts the focus automatically while
monitoring the screen continuously in the auto mode.
In the auto focusing mode, zoom key operation is not
recognized as the input of the focus key.
One Push: It will be focused in about 5 seconds after zooming,
panning, and return to MANUAL mode automatically.
This is for focusing accurately after zooming.
Manual: In the manual mode, users can adjust the camera
focus manually.
Infinity: infinity focus is the state where a lens forms an image of an object an infinite distance away.
This corresponds to the point of focus for parallel rays.
Set the speed for camera focusing.
FOCUS MENU
FOCUS MODE : AUTO
FOCUS SPD : USER
NEAR LIMIT : 10CM
AF MODE : NORMAL
SENSITIVITY : NORMAL
BACK
< NEAR / RIGHT
AF MODE SEL >
FOCUS MENU
FOCUS MODE : AUTO
FOCUS SPD : USER
NEAR LIMIT : 10CM
AF MODE : NORMAL
SENSITIVITY : NORMAL
BACK
< NEAR / RIGHT
AF MODE SEL >
CAMERA MENU
ZOOM MODE
FOCUS MODE
AE MODE
WB MODE
ICR MODE
SPECIAL
CAM RESET
SAVE BACK EXIT
< NEAR / RIGHT
AE SET >
AUTO EXPOSURE
AUTO EXPO.MENU
AE MODE : AUTO
SHUTTER SPED : AUTO
SLOWSHUTTER : ON
IRIS LEVEL : AUTO
GAIN LEVEL : AUTO
AGC MODE : ON
EXPO. MODE : ON
EXPO. LEVEL : 0dB
BACK
< NEAR / RIGHT
AE MODE >
AE setting is a function adjusting shutter speed acoording to subject’s brightness to get standard
amount of exposed light.
AF MODE: Set the auto focuse mode
select : or Set ON :
Set OFF :
NEAR
NEAR
select : or Set ON :
Set OFF :
NEAR
NEAR
SENSITIVITY: Set the sensitivity of focus
select : or Set ON :
Set OFF :
NEAR
NEAR
select : or Set ON :
Set OFF :
NEAR
NEAR
Set the focus distance.
Select AUTO,MANUAL,SHUTTER, IRIS or BRIGHT.
FOCUS MENU
FOCUS MODE : AUTO
FOCUS SPD : USER
NEAR LIMIT : 10CM
AF MODE : NORMAL
SENSITIVITY : NORMAL
BACK
< NEAR / RIGHT
AF MODE SEL >
FOCUS MENU
FOCUS MODE : AUTO
FOCUS SPD : USER
NEAR LIMIT : 10CM
AF MODE : NORMAL
SENSITIVITY : NORMAL
BACK
< NEAR / RIGHT
AF MODE SEL >
FOCUS MENU
FOCUS MODE : AUTO
FOCUS SPD : USER
NEAR LIMIT : 10CM
AF MODE : NORMAL
SENSITIVITY : NORMAL
BACK
< NEAR / RIGHT
AF MODE SEL >
28
EWSJ Series Outdoor Speed PTZ Dome Camera System User’s Guide
29
EWSJ Series Outdoor Speed PTZ Dome Camera System User’s Guide
AE MODE : AUTO
SHUTTER SPED : AUTO
SLOWSHUTTER : ON
IRIS LEVEL : AUTO
GAIN LEVEL : AUTO
AGC MODE : ON
EXPO. MODE : ON
EXPO. LEVEL : 0dB
BACK
< NEAR / RIGHT
SHUTTER SPD >
AE MODE : AUTO
SHUTTER SPED : AUTO
SLOWSHUTTER : ON
IRIS LEVEL : AUTO
GAIN LEVEL : AUTO
AGC MODE : ON
EXPO. MODE : ON
EXPO. LEVEL : 0dB
BACK
< NEAR / RIGHT
SLOW SHT >
AE MODE : AUTO
SHUTTER SPED : AUTO
SLOWSHUTTER : ON
IRIS LEVEL : AUTO
GAIN LEVEL : AUTO
AGC MODE : ON
EXPO. MODE : ON
EXPO. LEVEL : 0dB
BACK
< NEAR / RIGHT
IRIS LEVEL >
AE MODE : AUTO
SHUTTER SPED : AUTO
SLOWSHUTTER : ON
IRIS LEVEL : AUTO
GAIN LEVEL : AUTO
AGC MODE : ON
EXPO. MODE : ON
EXPO. LEVEL : 0dB
BACK
< NEAR / RIGHT
GAIN LEVEL >
select : or Set ON :
Set OFF :
NEAR
NEAR
Select ON/ OFF.
select : or Set ON :
Set OFF :
NEAR
NEAR
If you set SHUTTER in the AE MODE, you can control image
brightness by adjusting shutter speed.
Set from 1/60 , 1/90 , 1/100, 1/180, 1/250, 1/500, 1/1000,
1/1500, 1/2000, 1/5000, 1/10000, 1/20000, 1/50000, 1/100000
select : or Set ON :
Set OFF :
NEAR
NEAR
If you set IRIS in the AE MODE, you can set the IRIS level
from 00 to 17 .
select : or Set ON :
Set OFF :
NEAR
NEAR
If you set MANUAL, IRIS and SHUTTER in the AE MODE, you can
set the GAIN for brighter image from 0~30dB. (Changable by 2dB)
AUTO EXPO.MENU
AUTO EXPO.MENU
AUTO EXPO.MENU
AUTO EXPO.MENU
AE EXPO.MENU
AE MODE : AUTO
SHUTTER SPED : AUTO
SLOWSHUTTER : ON
IRIS LEVEL : AUTO
GAIN LEVEL : AUTO
AGC MODE : ON
EXPO. MODE : ON
EXPO. LEVEL : 0dB
BACK
< NEAR / RIGHT
AGC MODE >
AE EXPO.MENU
AE MODE : AUTO
SHUTTER SPED : AUTO
SLOWSHUTTER : ON
IRIS LEVEL : AUTO
GAIN LEVEL : AUTO
AGC MODE : ON
EXPO. MODE : ON
EXPO. LEVEL : 0dB
BACK
< NEAR / RIGHT
EXPO. MODE >
AE EXPO.MENU
AE MODE : AUTO
SHUTTER SPED : AUTO
SLOWSHUTTER : ON
IRIS LEVEL : AUTO
GAIN LEVEL : AUTO
AGC MODE : ON
EXPO. MODE : ON
EXPO. LEVEL : 0dB
BACK
< NEAR / RIGHT
EXPO. LEVEL >
select : or Set ON :
Set OFF :
NEAR
NEAR
select : or Set ON :
Set OFF :
NEAR
NEAR
Select ON/ OFF in AGC MODE.
select : or Set ON :
Set OFF :
NEAR
NEAR
Select AUTO or Manual.
If you set ON in the EXPO MODE, you can control this level.
( "0" is standard (±10.5 selectable), changed bt 1.5dB)
30
EWSJ Series Outdoor Speed PTZ Dome Camera System User’s Guide
31
EWSJ Series Outdoor Speed PTZ Dome Camera System User’s Guide
CAMERA MENU
ZOOM MODE
FOCUS MODE
AE MODE
WB MODE
ICR MODE
SPECIAL
CAM RESET
SAVE BACK EXIT
< NEAR / RIGHT
WB SET >
select : or Set ON :
Set OFF :
NEAR
NEAR
select : or Set ON :
Set OFF :
NEAR
NEAR
WHTE BALANCE
Set the white balance of camera.
WHITE BALANCE MENU
WB MODE : AUTO
RED GAIN : xxx
BLUE GAIN: xxx
BACK
< NEAR / RIGHT
WB MODE SEL >
WHITE BALANCE MENU
WB MODE : AUTO
RED GAIN : 208
BLUE GAIN: 162
BACK
< NEAR / RIGHT
R GAIN SEL >
White balance setting is a function revising color temperature
to resolve the problem that screen’s colors change
by the color
temperature’s difference arrcording to time.
WB MODE: Set the color depend on white balacne.
WB MODE : Select AUTO, INDOOR, OUTDOOR ONEPUSH,
ATW or MANUAL.
RED GAIN: Adjust red color level from 0~255.
(Standard level is 025)
BLUE GAIN: Adjust blue color level from 0~255.
(Standard level is 025)
CAMERA MENU
ZOOM MODE
FOCUS MODE
AE MODE
WB MODE
ICR MODE
SPECIAL
CAMERA RESET
SAVE BACK EXIT
< NEAR / RIGHT
ICR SET >
ICR MENU
ICR MODE : AUTO
ICR THRESHOLD :10
BACK
< NEAR / RIGHT
ICR MODE >
ICR MODE
Set the LED operating depend on IRC Mode.
Select AUTO, DAY ,NIGHT, EXIT and SENSE IN mode and the LED will be operated depend on this mode.
ICR MENU
ICR MODE : AUTO
ICR THRESHOLD :10
BACK
< NEAR / RIGHT
ICR THRESHOLD >
select : or Set ON :
Set OFF :
NEAR
NEAR
Set the ICR THRESHOLD from 00 to 28 .
32
EWSJ Series Outdoor Speed PTZ Dome Camera System User’s Guide
33
EWSJ Series Outdoor Speed PTZ Dome Camera System User’s Guide
MAIN MENU
< NEAR / RIGHT
SPECIAL SET >
MOTION
DOME
CAMERA
CLEAR
CAM RESET
SPECIAL
SAVE BACK EXIT
SPECIAL MENU
APERTUREGAIN : 07
FLICKERLESS : OFF
BACK LIGHT : OFF
LINE LOCK : OFF
V PHASE : XXX
DNR LEVEL : AUTO
WDR MODE : OFF
BACK
< NEAR / RIGHT
APERTURE >
SPECIAL MENU
APERTUREGAIN : 07
FLICKERLESS : OFF
BACK LIGHT : OFF
LINE LOCK : OFF
V PHASE : XXX
DNR LEVEL : AUTO
WDR MODE : OFF
BACK
< NEAR / RIGHT
FLICKERLESS >
SPECIAL MENU
APERTUREGAIN : 07
FLICKERLESS : OFF
BACK LIGHT : OFF
LINE LOCK : OFF
V PHASE : XXX
DNR LEVEL : AUTO
WDR MODE : OFF
BACK
< NEAR / RIGHT
BACK LIGHT >
SPECIAL MENU
APERTUREGAIN : 07
FLICKERLESS : OFF
BACK LIGHT : OFF
LINE LOCK : OFF
V PHASE : XXX
DNR LEVEL : AUTO
WDR MODE : OFF
BACK
< NEAR / RIGHT
BACK LIGHT >
select : or Set ON :
Set OFF :
NEAR
NEAR
select : or Set ON :
Set OFF :
NEAR
NEAR
SPECIAL
In the Special menu, it’s available to set APERTUREGAIN, BACK LIGHT, DAY&NIGHT MODE,
DAY&NIGHT LEVEL and WDR.
select : or Set ON :
Set OFF :
NEAR
NEAR
Set the APERTUREGAIN value .(00~15)
Select ON/OFF in the FLICKERLESS function.
Select ON/OFF in the BACK LIGHT function.
Select ON/OFF by using joystick.
select : or Set ON :
Set OFF :
NEAR
NEAR
MAIN MENU
< NEAR / RIGHT
RESET >
MOTION
DOME
CAMERA
CLEAR
CAM RESET
SPECIAL
SAVE BACK EXIT
Make initialize the setting value which is set in CAMERA MENU.
CAMERA RESET
SPECIAL MENU
APERTUREGAIN : 07
FLICKERLESS : OFF
BACK LIGHT : OFF
LINE LOCK : OFF
V PHASE : XXX
DNR LEVEL : AUTO
WDR MODE : OFF
BACK
< NEAR / RIGHT
V PHASE >
SPECIAL MENU
APERTUREGAIN : 07
FLICKERLESS : OFF
BACK LIGHT : OFF
LINE LOCK : OFF
V PHASE : XXX
DNR LEVEL : AUTO
WDR MODE : OFF
BACK
< NEAR / RIGHT
DNR LEVEL >
SPECIAL MENU
APERTUREGAIN : 07
FLICKERLESS : OFF
BACK LIGHT : OFF
LINE LOCK : OFF
V PHASE : XXX
DNR LEVEL : AUTO
WDR MODE : OFF
BACK
< NEAR / RIGHT
WDR MODE >
If you set ON in the LINE LOCK menu, you can set
the V PHASE.
select : or Set ON :
Set OFF :
NEAR
NEAR
Set the DNR LEVEL from AUTO, OFF and 1 ~ 10.
select : or Set ON :
Set OFF :
NEAR
NEAR
Set the WDR MODE from OFF, LEV1 ~LEV7.
select : or Set ON :
Set OFF :
NEAR
NEAR
Move : Select : NEAR
34
EWSJ Series Outdoor Speed PTZ Dome Camera System User’s Guide
35
EWSJ Series Outdoor Speed PTZ Dome Camera System User’s Guide
5. 1 Mechanism Specification
5. 1. 1 MECHANICAL
5. 1. 2 ENVIRONMENTAL
5. 1. 3 FUNCTIONS
5. 1. 4 ELECTRICAL
5. 1. 5 USER CONNECTRIONS
5. 1. 6 CERTIFICATIONS
5. SPECIFICATION
- Pan : 360° Continuous Pan, 0.1º to 160º/sec. (64 steps proportional to zoom)
- Pan Preset Speed : 330°/sec, ± 0.1° Accuracy
- Tilt : 0.1º to 140º/sec. (proportional to zoom)
- Tilt Preset Speed : 250°/sec, ± 0.05° Accuracy
- Weight : Approx. 4.4Kg (10.8 lbs) / Packing : 4.9Kg
- Dimensions : 236(Ø) x 319(D) mm – 166(Ø) dome
- Construction : Aluminum
- Ingress Protection : IP66 (Outdoor Housing)
- Color : Cool gray
- Operating Temp : Indoor : 0°C to 50°C (32° F to 122° F)
Outdoor : -10°C to 50°C (14° F to 122° F)/ with 33W Heater(Optional 62.7W)
- Storage Temp : -20°C to 60°C (-4° F to 140° F)
- Humidity : 0% to 90% (non-condensing)
- Fan operate : 45°C on , 35°C off
- Heater operate : 5°C on , 15°C off
- Preset : 255 points, less than 0.1° accuracy
- Tour : 8 programmable
- Pattern : 4 patterns for 240 second.
- Auto Flip : Auto / Off (Rotate 90° at bottom of tilt)
- Scan : 8 (programmable speed and diagonal scan)
- Privacy Zone : 8 block with title (Mask)
- ID Address : Up to 255 selectable ID (Rotary switch)
- Data Communication Control : RS-485 / RS-422
- Protocol : Multiple protocol (PELCO-D/P, WONWOO)
- Baud rate : 2400, 4800, 9600, 19200, 38400, 57600 bps selectable
- Alarm In : 8 alarm
- Alarm Out : 2 relay out
- Display : 16 Area title
- Power : AC21~26V 60Hz / 50Hz(Power adaptor not included)
: DC10~14V 60Hz / 50Hz(Power adaptor not included)
- Camera Power Consumption : 18.0W
- Heater Power Consumption : 33W
- RS-422, 485 : Dip Switch setting
- Power(Camera) : AC24V, 50/60Hz (Max)15W
: DC12V, 50/60Hz (Max)20W
- Power(Heater) : AC24V, 50/60Hz (Max)35W
: DC12V, 50/60Hz (Max)54W (Max 5A)
- Data communication connection : RS-422, 485 + / - Optional Control Data
- Video connection : BNC
- Alarm Inputs : 8 Programmable
- Relay Out : 2 Dry Contact Output Rating: 2A @30VAC
- CE EMC , FCC CLASS A, RoHS
Here you can clear programmed Preset, Tour, Scan, Pattern, Area, Alarm
and Privacy.
4. 6. 1 Preset
Clear up all of memorized Preset data
4. 6. 2 Tour
Clear up all of memorized Tour data
4. 6. 3 Scan
Clear up all of memorized Scan data
CLEAR MENU
PRESET
TOUR
SCAN
PATTEN
AREA
ALARM
PRIVACY
BACK EXIT
< NEAR / RIGHT ▷ PRESET >
4. 6. 4 Pattern
Clear up all of memorized Pattern data
4. 6. 5 Area
Clear up all of memorized Area data
4. 6. 6 Alarm
Clear up all of memorized Alarm data
4. 6. 7 Privacy
Clear up all of memorized Privacy data
4. 5. 4 Clear Menu
36
EWSJ Series Outdoor Speed PTZ Dome Camera System User’s Guide
37
EWSJ Series Outdoor Speed PTZ Dome Camera System User’s Guide
5. 2 Camera Specification
5. 2. 1 EWSJ-270
- Image Sensor : 1/4 inch Sony Super HAD CCD
- Lens : 27x Optical Zoom
- Total Pixels (HV) : 811 x 508 (NTSC), 795 x 596 (PAL)
- Effective Pixels : 768 x 494 (NTSC), 752 x 582 (PAL)
- Resolution : 550 TV Lines (Color) / 680 TV Lines(B/W)
- Focus mode : Auto Focus / Manual Focus / One-push AF
- Iris mode : Automatic with Manual Override
- Video Output : Composite 1.0Vp-p, 75Ω, BNC
- Sync. : Internal Sync
- S/N Ratio : Higher than 50dB (AGC OFF)
- Min. Illumination : 0.4Lux/F1.6(Color),0.02Lux/F1.6(B/W) /(@50IRE)
- Electronic Shutter : AUTO/MANUAL/A.FLK (1/120,000 – X256)
- Privacy Function : ON/OFF (8Areas)
- Flip : ON/OFF
- DIS : ON/OFF
- SSNR : LOW/MEDIUM/HIGH/OFF
- Day&Night : AUTO/COLOR/BW/EXT, IR-Cut Filter Removable
- White Balance : ATW/AWC/MANUAL/INDOOR/OUTDOOR (1,800K~10,500K)
- Lens Initialize : Built-in
- Iris : AUTO/MANUAL
- Gain Control : LOW/MEDIUM/HIGH/MANUAL/OFF
- OSD Display : ON/OFF
- Focal length : F3.5 ~ 94.5mm (F 1.6 to 2.9)
- Digital Zoom : OFF, ON (Limit 12x) (Total 324X Zoom)
- Min. Focus Distance : 1,500mm
- Coverage Angle : F=3.5mm 55.5°(Horizontal) X 42.5°(Vertical)
F=94.5mm 2.24°(Horizontal) X 1.79°(Vertical)
5. 2. 2 EWSJ-330
- Image Sensor : 1/4 inch Sony Super HAD CCD
- Lens : 33x Optical Zoom
- Total Pixels (HV) : 811 x 508 (NTSC), 795 x 596 (PAL)
- Effective Pixels : 768 x 494 (NTSC), 752 x 582 (PAL)
- Resolution : 550 TV Lines (Color) / 680 TV Lines(B/W)
- Focus mode : Auto Focus / Manual Focus / One-push AF
- Iris mode : Automatic with Manual Override
- Video Output : Composite 1.0Vp-p, 75Ω, BNC
- Sync. : Internal Sync
- S/N Ratio : Higher than 50dB (AGC OFF)
- Min. Illumination : 0.4Lux/F1.6(Color),0.02Lux/F1.6(B/W) /(@50IRE)
- Electronic Shutter : AUTO/MANUAL/A.FLK (1/120,000 – X256)
- Privacy Function : ON/OFF (8Areas)
- Flip : ON/OFF
- DIS : ON/OFF
- SSNR : LOW/MEDIUM/HIGH/OFF
- Day&Night : AUTO/COLOR/BW/EXT, IR-Cut Filter Removable
- White Balance : ATW/AWC/MANUAL/INDOOR/OUTDOOR (1,800K~10,500K)
- Backlight : BLC/HLC/OFF
- Lens Initialize : Built-in
- Iris : AUTO/MANUAL
- Gain Control : LOW/MEDIUM/HIGH/MANUAL/OFF
- OSD Display : ON/OFF
- Focal length : F3.5 ~ 115.5mm (F 1.6 to 3.6)
- Digital Zoom : OFF, ON (Limit 12x) (Total 396X Zoom)
- Min. Focus Distance : 1,500mm
- Coverage Angle : F=3.5mm 55.5°(Horizontal) X 42.5°(Vertical)
F=115.5mm 1.77°(Horizontal) X 1.33°(Vertical)
38
EWSJ Series Outdoor Speed PTZ Dome Camera System User’s Guide
39
EWSJ Series Outdoor Speed PTZ Dome Camera System User’s Guide
5. 2. 3 EWSJ-331
- Image Sensor : 1/4 inch Double Density Interline Transfer CCD
- Lens : 33x Optical Zoom
- Total Pixels (HV) : 811 x 508 (NTSC), 795 x 596 (PAL)
- Effective Pixels : 768 x 494 (NTSC), 752 x 582 (PAL)
- Resolution : 550 TV Lines (Color) / 680 TV Lines(B/W)
- Focus mode : Auto Focus / Manual Focus / One-push AF
- Iris mode : Automatic with Manual Override
- Video Output : Composite 1.0Vp-p, 75Ω, BNC
- Sync. : Internal Sync
- S/N Ratio : Higher than 50dB (AGC OFF)
- Min. Illumination : 0.7Lux/F1.6(Color),0.03Lux/F1.6(B/W) /(@50IRE)
- Electronic Shutter : AUTO/MANUAL/A.FLK (1/120,000 – X256)
- Privacy Function : ON/OFF (8Areas)
- Flip : ON/OFF
- DIS : ON/OFF
- SSNR : LOW/MEDIUM/HIGH/OFF
- Day&Night : AUTO/COLOR/BW/EXT, IR-Cut Filter Removable
- White Balance : ATW/AWC/MANUAL/INDOOR/OUTDOOR (1,800K~10,500K)
- Backlight : WDR/BLC/HLC/OFF
- Lens Initialize : Built-in
- Iris : AUTO/MANUAL
- Gain Control : LOW/MEDIUM/HIGH/MANUAL/OFF
- OSD Display : ON/OFF
- Focal length : F3.5 ~ 115.5mm (F 1.6 to 3.6)
- Digital Zoom : OFF, ON (Limit 12x) (Total 396X Zoom)
- Min. Focus Distance : 1,500mm
- Coverage Angle : F=3.5mm 55.5°(Horizontal) X 42.5°(Vertical)
F=115.5mm 1.77°(Horizontal) X 1.33°(Vertical)
5. 2. 4 EWSJ-370
- Image Sensor : 1/4 inch Sony Super HAD CCD
- Lens : 37x Optical Zoom
- Total Pixels (HV) : 811 x 508 (NTSC), 795 x 596 (PAL)
- Effective Pixels : 768 x 494 (NTSC), 752 x 582 (PAL)
- Resolution : 550 TV Lines (Color) / 680 TV Lines(B/W)
- Focus mode : Auto Focus / Manual Focus / One-push AF
- Iris mode : Automatic with Manual Override
- Video Output : Composite 1.0Vp-p, 75Ω, BNC
- Sync. : Internal Sync
- S/N Ratio : Higher than 50dB (AGC OFF)
- Min. Illumination : 0.4Lux/F1.6(Color),0.02Lux/F1.6(B/W) /(@50IRE)
- Electronic Shutter : AUTO/MANUAL/A.FLK (1/120,000 – X256)
- Privacy Function : ON/OFF (8Areas)
- Flip : ON/OFF
- DIS : ON/OFF
- SSNR : LOW/MEDIUM/HIGH/OFF
- Day&Night : AUTO/COLOR/BW/EXT, IR-Cut Filter Removable
- White Balance : ATW/AWC/MANUAL/INDOOR/OUTDOOR (1,800K~10,500K)
- Backlight : BLC/HLC/OFF
- Lens Initialize : Built-in
- Iris : AUTO/MANUAL
- Gain Control : LOW/MEDIUM/HIGH/MANUAL/OFF
- OSD Display : ON/OFF
- Focal length : F3.5 ~ 129.5mm (F 1.6 to 3.9)
- Digital Zoom : OFF, ON (Limit 12x) (Total 444X Zoom)
- Min. Focus Distance : 1,500mm
- Coverage Angle : F=3.5mm 55.5°(Horizontal) X 42.5°(Vertical)
F=129.5mm 1.59°(Horizontal) X 1.19°(Vertical)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27

Wonwoo EWSJ-223 Installation & Operating Manual

Category
Security cameras
Type
Installation & Operating Manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI