TAC 140950 User manual

Brand: TAC

Model: 140950

Type: User manual

TAC 140950 is a set of aluminum running boards designed to provide easy access to your 2005-2022 Nissan Frontier Crew Cab. These durable running boards feature a maximum load capacity of 200 lbs and come with all the necessary mounting hardware for a simple and secure installation. Protect your investment by waxing after installation and maintain with regular waxing to prolong their lifespan.

www.tacautoparts.com

INSTALLATION INSTRUCTIONS

VIEWPOINT ALUMINUM RUNNING BOARD

2005-2022 NISSAN FRONTIER CREW CAB

PART# 140950

VIEWPOINT ALUMINUM RUNNING BOARD

2005-22 NISSAN FRONTIER CREW CAB

www.tacautoparts.com Page 1 of 2 9/5/12 (DP)

Parts List:

1 Driver/ Left Running Board 12 8mm Hex Nuts

1 Passenger/Right Running Board 12 6mm “T” Bolts

6 Mounting Brackets 12 6mm x 22mm OD x 2mm Large Flat Washers

12 8mm x 24mm x 2mm Flat Washers 12 6mm Lock Washers

12 8mm Lock Washers 12 6mm Hex Nuts

PROCEDURE:

1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ

INSTRUCTIONS CAREFULLY. PLEASE NOTE: 200LBS IS THE MAXIMUM RATED LOAD

FOR THE VIEWPOINT RUNNING BOARDS.

2. Locate the threaded studs on the inner body panel, (Figure 1). Select (1) Mounting Bracket

and hang it from the front mounting location, (Figures 2 & 3). Secure it with the included (2)

8mm Flat Washers, (2) 8mm Lock Washers and (2) 8mm Hex Nuts. Snug hardware but do not

tighten at this time.

3. Repeat Step 2 for the driver side Center and Rear Mounting Bracket installation, (Figures 2 &

3).

4. Select the driver/left side Running Board. Locate the openings cut at the end of the slots on the

bottom of the Running Board, (Figure 4). Insert (3) 6mm T-Bolts into each channel through the

openings. Slide the T-Bolts into the approximate position in line with the (3) Brackets.

5. Carefully place the Running Board in position on top of the Brackets. Slide the T-Bolts forward

or back until they line up and drop into the slots on the Brackets. Secure the Running Board to

the Brackets with (6) 6mm Flat Washers, (6) 6mm Lock Washers and (6) 6mm Hex Nuts,

(Figure 5). Do not tighten hardware at this time.

6. Adjust and level the Running Board and tighten all hardware.

7. Repeat Steps 2 - 6 for passenger Running Board installation.

8. Do periodic inspections to the installation to make sure that all hardware is secure and tight.

To protect your investment, wax this product after installing. Regular waxing is recommended to add a

protective layer over the finish. Do not use any type of polish or wax that may contain abrasives that could

damage the finish.

For stainless steel: Aluminum polish may be used to polish small scratches and scuffs on the finish. Mild

soap may be used also to clean the Running Board.

Passenger/Right

Running Board

Driver/Left

Running Board

(6) Mounting Brackets

Front

VIEWPOINT ALUMINUM RUNNING BOARD

2005-22 NISSAN FRONTIER CREW CAB

www.tacautoparts.com Page 2 of 2 9/5/12 (DP)

Driver Side Installation Pictured

(Fig 1) Locate factory mounting locations

Fig 3

Fig 4

Slide 6mm T-Bolts into slots

at end of Running Board

Rear

(2) 8mm Flat Washers

(2) 8mm Lock Washers

(2) 8mm Hex Nuts

Fig 2

Complete Installation

Fig 4

(2) 8mm Flat Washers

(2) 8mm Lock Washers

(2) 8mm Hex Nuts

(2) 6mm T-Bolts

(2) 6mm Flat Washers

(2) 6mm Lock Washers

(2) 6mm Hex Nuts

TAC 140950 User manual

Brand: TAC

Model: 140950

Type: User manual

Download PDF

report

TAC 140950 User manual

TAC 140950 User manual

Related papers

Other documents