Broadcom HFBR-0539Z Evaluation Kit User guide

Type
User guide
HFBR-0539Z Evaluation Kit
DC to 12 MBd Probus 650 nm Fiber Optics Eval Kit
User Guide
Introduction
HFBR-0539Z evaluation kit is used to evaluate Avago ber optic device HFBR-1515BZ and HFBR-2515BZ. The evaluation
kit is equipped with necessary documents and accessories to ease product evaluation and verication.
Evaluation Kit
HFBR-0539Z contains:
1. Evaluation board
2. HFBR-1515BZ and HFBR-2515BZ unit
3. HCS® Cable with ST connector
4. HFBR-1515BZ /2515BZ datasheet
5. User guide document
Evaluation Board
The basic evaluation board that you receive from Avago incorporates transmitter driver IC SN75451BD, some passive
components, and SMA connectors for the TX input (TXD) and RX output (RXD) port connection. This basic evaluation
board allows you to connect waveform/pattern generator to the TXD with TTL input signal. Receivers output signal can
be monitored from the RXD or RXout with oscilloscope by using high impedance setting.
Initial Setup
1. Connect 5 V supply voltage to TXVCC and RXVCC
2. Connect 0 V to TXGND and RXGND
3. Connect TXD to pattern generator output
4. Connect RXout to Oscilloscope with high impedance probe
Bit Error Rate Test Setup
Though the transmitter driver IC’s input and receivers output is based on TTL logic (high impedance), the board can be
modied to connect 50 ohm load instrument by doing the following steps:
1. Put R2 (50 ohm resistor).
2. Remove R3 (0 ohm resistor).
3. Put R4 (0 ohm resistor) and R7 (50 ohm resistor).
4. Put U3 (SN74LVC2G125).
5. Connect BVCC (5 V) and BGND (0 V).
HCS® is a trademark of OFS
For product information and a complete list of distributors, please go to our web site: www.avagotech.com
Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries.
Data subject to change. Copyright © 2005-2010 Avago Technologies. All rights reserved.
AV02-2662EN - October 5, 2010
5
6
7
8
1 4
TX
HFBR-15x5A/BZ
RX
HFBR-25x5A/BZ
1 4
TXVCC
RXVCC
TXGND
TXGND
RXGND
TXGND
TXGND
RXGND
RXGND
TXGND
2
2
1
1
Jack
TXVCC
Test_Jack
2
2
1
1
Jack
TXGND
Test_Jack
2
2
1
1
Jack
RXVCC
Test_Jack
2
2
1
1
Jack
RXGND
Test_Jack
TXGND TXGND
TXVCC TXVCC
RXVCC RXVCC
RXGND RXGND
47
R1
Res Semi
0
R3
Res Semi
10Eb
1
1A
2
2Y
3
GND
4
2A
5
1Y
6
20Eb
7
VCC
8
U3
SN74LVC2G125
0
R4
Res Semi
0
R6
Res Semi
BGND
BGND
BVCC
2
2
1
1
Jack
BVCC
Test_Jack
2
2
1
1
Jack
BGND
Test_Jack
BVCC BVCC
BGND BGND
BGND
Pin
1
GND
2
TXin
Pin
Pin
1
GND
2
RXout
Pin
TXGND
RXGND
0.1 µF
C2
1
1
2
3
4
5
TXD
SMA
1
1
2
3
4
5
RXD
SMA
1A
1
2A
6
1B
2
2B
7
VCC
8
GND
4
1Y
3
2Y
5
U1
SN75451BD
TXVCC
TXGND
10 µF
C1
T491B106K016AT
50
R7
Res Semi
50
R5
Res Semi
50
R2
Res Semi
5
6
7
8
RXGND
100 pF
C3
Cap Semi
RXGND
2.7
R8
Res Semi
  • Page 1 1
  • Page 2 2

Broadcom HFBR-0539Z Evaluation Kit User guide

Type
User guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI