Polaris 9300xi Sport Owner's manual

Brand: Polaris

Model: 9300xi Sport

Category: Above ground pool accessories

Type: Owner's manual

W2093A RevA

Polaris 9300xi Sport

Owner's Manual

Manuel du propriétaire

Manual del usuario

AVERTISSEMENT

POUR VOTRE SÉCURITÉ – Pour toute opération autre que l’entretien de routine et la maintenance

décrite dans ce manuel, ce produit doit être pris en charge par une entreprise qui est autorisée et

qualiﬁ ée pour la réparation des équipements de piscine par la juridiction où le dit produit est installé

lorsque de telles exigences locales ou provinciales sont édictées. Si aucune exigence locale ou

provinciale n’est disponible, l’agent d’entretien doit être un professionnel avec sufﬁ samment d’expé-

rience dans l’installation et la maintenance d’équipement de piscine pour appliquer correctement les

consignes du présent manuel. L’installation ou l’utilisation inappropriée annulera la garantie.

WARNING

FOR YOUR SAFETY - For anything other than the routine cleaning and maintenance described

in this manual, this product must be serviced by a contractor who is licensed and qualiﬁ ed in pool

equipment by the jurisdiction in which the product will be installed where such state or local

requirements exist. In the event no such state or local requirement exists, the maintainer must be

a professional with sufﬁ cient experience in pool equipment installation and maintenance so that all

of the instructions in this manual can be followed exactly. Improper installation and/or operation will

void the warranty.

ADVERTENCIA

PARA SU SEGURIDAD - Para cualquier cosa con excepción de la limpieza rutinaria y

mantenimiento de descritos en este manual, este producto debe ser atendido por un contratista que

está autorizado y caliﬁ cado en equipo de piscina bajo la jurisdicción en la que el producto se instala

en donde requisitos de estado y locales existen. En el caso de que no exista ningún requisito de

estado o local, el responsable debe ser un técnico profesional con experiencia suﬁ ciente en la

instalación de piscinas y mantenimiento de equipo para que todas las instrucciones en este manual

puede ser seguidas exactamente. Inapropiada instalación y/o operación anulará la garantía.

Page is loading ...

Page 3

THANK YOU FOR PURCHASING THE POLARIS 9300 SPORT CLEANER.

YOUR POLARIS 9300xi SPORT HAS BEEN DESIGNED AND MANUFACTURED TO BE EASILY INSTALLED AND

TO PROVIDE LOW MAINTENANCE OPERATION. PRIOR TO INSTALLING YOUR NEW POLARIS 9300xi SPORT,

PLEASE DO THE FOLLOWING:

1) Complete and return the warranty card.

2) Record your purchase information on the spaces provided below.

3) Attach your invoice (or a copy) to this page.

Taking these steps will help ensure prompt warranty service, should it be required. If service is required, please

contact your original dealer. If the original dealer does not perform warranty service, please visit

www.polarispool.com to locate an independent service company near you. If you are unable to locate a service

company, please call our Technical Support department at 800-822-7933.

RECORD YOUR 9300xi SPORT POOL CLEANER DATA HERE:

Date of Purchase Purchased From Serial Number:

(located on machine head)

City State Zip Code

Table of Contents

Section 1. Important Safety Instructions .........4

Section 2. 9300xi Sport Speciﬁ cations............6

2.1 General Speciﬁ cations ...................6

Section 3. Assembly and Initial Usage............6

3.1 Unpacking ......................................6

3.2 Assembling the Transport Caddy ...6

3.3 Connecting the Control Unit

to the Caddy ...................................8

3.4 Electrical Connection .....................8

Section 4. Operation .......................................9

4.1 Submerging the Cleaner ................9

4.2 Operating the Cleaner ....................9

4.3 Removing the Cleaner ...................10

4.4 Remote Control Mode ....................10

4.5 Enabling the Automatic

Start Mode ......................................11

Section 5. Cleaning and Maintenance ............11

5.1 Cleaning the Filter Canister ............11

5.2 Cleaning and Storing the

Cleaner ...........................................12

5.3 Replacing the Brushes ...................13

5.4 Replacing the Tires on the

Cleaner ...........................................14

Section 6. Troubleshooting .............................15

6.1 General Troubleshooting ................15

Section 7. Polaris 9300xi Sport Exploded View

and Replacement Parts List ...........16

7.1 Parts List .......................................16

7.2 Exploded View ...............................17

English

Page 4

WARNING

Failure to comply with the following warnings can result in permanent injury, electrocution or

drowning.

PREVENT ELECTRICAL SHOCK

To reduce risk of electrical shock:

• Connect unit to receptacle protected by a ground fault circuit interrupter (GFCI). Such a GFCI receptacle

should be provided by a qualified installer and should be tested on a routine basis. To test the GFCI, push the

test button. The GFCI should interrupt power. Push the reset button. Power should be restored. If the GFCI

fails to operate in this manner, the GFCI is defective. If the GFCI interrupts power to the pump without the test

button being pushed, a ground current is flowing, indicating the possibility of an electric shock. Do not use

this product. Disconnect the cleaner and have the problem corrected by a qualified service representative

before using.

• Per the United States National Electric Code (NEC), keep the power unit at least 5 feet from the edge of

the (pool/spa) water and do not remove it from its caddy. In Canada, the Canadian Electrical Code (CEC)

requires a minimum distance of 3 m (10 ft.) to be maintained between the pool edge and the power unit. Never

submerge the control unit.

• Do not enter pool while the 9300xi Sport is in water.

• Do not bury cord. Locate cord so as to prevent it from being damaged by lawn mowers, hedge trimmers and

other equipment.

• To reduce the risk of electrical shock, do not use the 9300xi Sport cleaner or control unit if the cord is worn or

damaged. Contact Zodiac Pool Systems, Inc. immediately for a replacement cord.

• Double insulation—For continued protection against possible electric shock, use only identical replacement parts

when servicing. Do not attempt repair of the 9300xi Sport cleaner, control unit, power cord, or floating cable.

• NEVER OPEN CONTROL UNIT.

• Do not use an extension cord to connect the unit to electric supply; provide a properly located outlet. The

control unit should be placed near the outlet box.

PREVENT CHILD INJURY AND DROWNING

• To reduce the risk of injury, do not permit children to operate this product.

• Do not let anyone, especially small children, sit, step, lean, or climb on any equipment installed as part of

your pool’s operational system.

Section 1. Important Safety Instructions

Congratulations on purchasing the Polaris 9300xi Sport cleaner. Please take a moment to read through the entire

manual before installing your new robotic pool cleaner. Your cleaner must be installed and operated as speciﬁ ed.

READ AND FOLLOW ALL INSTRUCTIONS

English

Page 5

SAVE THESE INSTRUCTIONS

CAUTION

Failure to comply with the following warnings could cause damage to pool equipment or personal

injury.

• This product is intended for use with permanently-installed pools. Do not use with storable pools. A

permanently-installed pool is constructed in or on the ground or in a building such that it cannot be readily

disassembled for storage. A storable pool is constructed so that it is capable of being readily disassembled for

storage and reassembled to its original integrity.

• The 9300xi Sport must be installed and operated as specified.

• Turn the 9300xi Sport off before removing it from water, and do not operate out of water.

• Do not remove the 9300xi Sport from the pool for 15 minutes after the cleaning cycle has completed.

• Clean filter canister in the 9300xi Sport after each use.

• Do not use the product in your pool if the water temperature is above 95˚ F (35˚ C) or below 55˚ F (13˚ C).

CAUTION

USE OF THE POLARIS 9300 SPORT CLEANER IN A VINYL LINER POOL

Certain vinyl liner patterns are particularly susceptible to rapid surface wear of pattern removal caused by objects

coming into contact with the vinyl surface, including pool brushes, pool toys, floats, fountains, chlorine dispensers,

and automatic pool cleaners. Some vinyl liner patterns can be seriously scratched or abraded simply by rubbing

the surface with a pool brush. Ink from the pattern can also rub off during the installation process or when it comes

into contact with objects in the pool.

Zodiac Pool Systems, Inc., is not responsible for, and the Limited Warranty does not cover, pattern removal,

abrasion or markings on vinyl liners.

English

CAUTION

This device complies with part 15 of the FCC Rules. Operation is subject to the following two (2) conditions: (1) this

device may not cause harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation.

NOTE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residen-

tial installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications. However, there is no guaran-

tee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment

and receiver.

• Connect the equipment to an electrical source on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Modiﬁ cations made to this equipment, which are not authorized by the manufacturer, may void the user’s authority

to operate this equipment.

Page 6

Section 2. 9300xi Sport Speciﬁ cations

2.1 General Specifications

The general speciﬁ cations for the Polaris 9300xi Sport

are as follows:

To unpack the 9300xi Sport and its components:

1. Remove the lower portion of the caddy along with

the upper and lower power cable hooks, control

unit hook, power cable hook plate, locking plate,

nuts, bolts and screws.

2 Remove the small box that contains the control unit.

3. Remove the handles (left and right) of the caddy,

which are located against one side of the box.

4. Remove the cleaner from the box.

3.2 Assembling the Transport Caddy

1. Position the power cable hook and control unit

hook on the upper tubes as shown in Figure 2.

Make sure the upper tubes (handles) are in the

proper orientation.

Figure 1. Polaris 9300xi Sport Components

Figure 2. Install Hooks on the Upper Handles

English

9300xi Sport

Control box supply voltage

100-125 VAC, 60 Hz

Polaris 9300xi supply voltage 30 V DC

Installed load 150 W max

Cable length 70 ft (21 m)

Cleaner size (WxDxH)

16.9 x 18.9 x 10.6 in.

43 x 48 x 27 cm

Pack size (WxDxH)

22.8 x 22.8 x 23.2 in.

58 x 58 x 59 cm

Weight of Cleaner 25 lbs. (11.3 kg)

Packed weight 42 lbs. (19 kg)

Filtration

less than 100 microns

Cycle lengths 1.30 hrs, 2.30 hrs.

The Polaris 9300xi is a double-insulated product. A

double-insulated electrical appliance is one which has

been designed in such a way that it does not require a

safety connection to ground. The basic requirement for

double-insulation is that no single failure can result in

dangerous voltage becoming exposed so that it might

cause an electric shock and that this is achieved without

relying on an earthed (grounded) metal casing. This is

achieved by having two (2) layers of insulating material

surrounding live parts or by using reinforced insulation.

Therefore, devices having double-insulated construc-

tion, such as the Polaris 9300xi, do not utilize a ground-

ed (three-prong) cord/plug.

Section 3. Assembly and Initial

Usage

3.1 Unpacking

The packaging should contain the following items

(Refer to Figure 1):

• 9300xi Sport cleaner

• Control unit

• Remote control

• Transport and storage caddy (complete with

assembly components)

Check that the unit has not been damaged during

transport. If you detect damage, contact Zodiac Pool

Systems, Inc. at 1-800-822-7933 before using your

9300xi Sport cleaner.

Page 7

2. Secure the power cable hook and control unit hook

around the tubes using a screw and hand tighten

with the Torx

wrench (supplied with unit). Refer

to Figure 3.

3. Secure the control unit hook using two (2) bolts

and two (2) nuts and tighten with Torx wrench.

Refer to Figure 4.

4. Insert the upper tubes (handles) into the bottom

tubes on the cart as shown in Figure 5. Make

sure the upper tubes (handles) are in the proper

orientation and align the screw holes.

5. Position the bottom power cable hook as shown

in Figure 6. Place the cable hook plate opposite

the power cable hook. Secure using a screw and

tightening with the Torx wrench. Refer to Figure 7.

6. Secure the cable hook plate using two (2) bolts and

two (2) nuts and tighten with Torx wrench. Refer

to Figure 8. The transport caddy is now ready to

use as shown in Figure 9.

Figure 3. Install the Power Cable Hook and

Control Unit Hook

Figure 4. Secure the Hooks

Figure 5. Install the Handles

Figure 6. Position the Bottom Power Cable Hook

Figure 7. Secure the Bottom Power Cable Hook

Figure 8. Secure the Cable Hook Plate

Figure 9. Transport and Storage Caddy Assembled

English

Page 8

3.3 Connecting the Control Unit to the

Caddy

1. Position the control unit over the control unit hook

on the caddy.

2. Slide the locking plate clips into the control hook

and line up the screw holes. Refer to Figure 10.

Figure 12. Electrical Connection

3. Secure the locking plate using Phillips head

screws. Do not overtighten. Refer to Figure 11.

3.4 Electrical Connection

WARNING

Failure to comply with the following warnings can

result in permanent injury, electrocution or drowning.

PREVENT ELECTRICAL SHOCK

•

U.S.: Keep the control unit at least 5 feet from the edge

of the pool. CANADA: Per CEC requirements, keep

the control unit at least 3 m (10 ft.) from the edge of the

pool.

• Only connect the control unit to a receptacle

protected by a ground fault circuit interrupter (GFCI).

Contact a certified electrician if you cannot verify

that the receptacle is protected by a GFCI.

• Do not use an extension cord to connect the control

unit.

• Do not allow anyone to swim while the 9300xi Sport

cleaner is in the pool.

Figure 10. Position the Locking Plate Clips

Figure 11. Secure the Locking Plate

English

For your safety and to obtain the best possible

performance from your 9300xi Sport, connect the

cleaner’s ﬂ oating cable to the control unit and thread

connector until it is snug. Do not overtighten. Refer to

Figure 12.

IMPORTANT

• The 9300xi Sport control unit is equipped with an

automatic shut off feature to prevent overheating if

operated in direct sunlight for an extended period of

time.

• The 9300xi Sport control unit is water-resistant, not

waterproof. Therefore, never submerge the control

unit.

Floating Cable

Power Supply

Connector

Page 9

2. Ensure the unit sinks to the bottom of the pool.

Refer to Figure 14.

4.2 Operating the Cleaner

1. Plug the control unit into a GFCI protected power

source.

Select either the Cycle I or Cycle II cleaning

program on the control unit:

Cycle I Program Cycle II Program

• Completed in 1.5 hours • Completed in 2.5 hours

• Maximum coverage in

minimal time

• Intensive and complete

cleaning

• Thorough tile cleaning

2. To start your 9300xi Sport cleaner, press the button

for "Cycle I" cleaning program. "Cycle I" cleaning

is the primary cleaning cycle for inground pools.

3. When the "Cycle I" program button is selected the

indicator light above will illuminate. The cleaner

will start in a few seconds.

Figure 14. Cleaner on the Bottom of the Pool

Figure 15. Spread Floating Cable Over the Pool

Figure 16. Start the Cleaner

Figure 17. Turn Cleaner Off

Figure 13. Submerge the Cleaner Vertically

Section 4. Operation

4.1 Submerging the Cleaner

1. Submerge the cleaner in the pool and remove any

air trapped inside by keeping the unit vertical.

Refer to Figure 13.

3. Spread out the ﬂ oating cable over the pool,

ensuring there are no kinks or coils in the cable.

Refer to Figure 15.

4. Depending on the state of your pool it is possible

to modify the time of the cleaning cycle by

pressing the

button. Pressing the button

will increase the cleaning time by 60 minutes or

decrease the cleaning time by 30 minutes. When

the cleaner is powered on, the Cycle and time will

correspond to the cycle and the time that were

active at the time it was last switched off.

5. If you wish to stop the cleaner during a cleaning

cycle, press the "Power" button. Refer to Figure 17.

English

Page 10

4.3 Removing the Cleaner

CAUTION

To prevent damage to the 9300xi Sport, be sure to

adhere to the following guidelines:

1. After the cleaning cycle is completed, the four (4)

lights located on the control unit will ﬂ ash slowly

to indicate that the cleaner may be removed from

the pool.

2. Disconnect the control unit cable from the

electrical outlet.

3. Disconnect the cab

le from the control unit.

4. Never lift the 9300xi Sport out of the pool by the

ﬂ oating cable. Always use the handle to remove it

from the pool. Refer to Figures 18 and 19.

5. Coil the cable starting at the cleaner and go

toward the connection point at control unit.

Remove coils or twists along the way.

6. Store the Polaris 9300xi Sport on the caddy with

the cable coiled when not in use.

IMPORTANT NOTES

• The 9300xi Sport includes a safety feature that

automatically stops the cleaner after 20 seconds, if

it is powered on, but not submerged in the water.

For pools equipped with a beach area, this safety

feature allows the cleaner to reverse, and back into

the pool when the impeller is out of the water.

• Use your 9300xi Sport cleaner as often as needed

to keep your pool clean.

• Clean the ﬁ lter canister after each cleaning cycle.

• Do not leave your cleaner in the pool on a

permanent basis.

• At the end of each cycle, remove the cleaner from

the pool. Start at the cleaner head and untangle any

coils in the hose before storing the cleaner.

•

Remove the 9300xi Sport from pool when super

chlorinating.

4.4 Remote Control Mode

Figure 18. Remove Cleaner From Pool

Figure 19. Keep Cleaner Vertical to Drain Water

English

CAUTION

This device complies with part 15 of the FCC Rules.

Operation is subject to the following two (2) condi-

tions: (1) this device may not cause harmful interfer-

ence, and (2) this device must accept any interfer-

ence received, including interference that may cause

undesired operation.

NOTE This equipment has been tested and found

to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harm-

ful interference in a residential installation. This equip-

ment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that in-

terference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or

television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try

to correct the interference by one or more of the follow-

ing measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment

and receiver.

• Connect the equipment to an electrical source

on a circuit different from that to which the re-

ceiver is connected.

• Consult the dealer or an experienced radio/TV

technician for help.

Modiﬁ cations made to this equipment, which are not

authorized by the manufacturer, may void the user’s

authority to operate this equipment.

Page 11

Figure 21. Lift Cleaner Cover

Figure 20. Remote Control

Remote control of the Polaris 9300xi Sport is available

using the hand held remote control unit.

The remote control unit has four (4) buttons:

Procedure for cancelling an automatic start:

1. Connect the control unit to the receptacle.

2. Press the OFF button for more than six (6) seconds

3. The two (2) lights will ﬂ ash once

To turn the cleaner, you must hold down the rotate left

or rotate right button.

When using the remote control unit, the two (2) lights on

the control unit will ﬂ ash alternately.

To return to automatic mode, either stop using the re-

mote control unit buttons for a minimum of 45 seconds

or press Cycle I or Cycle II button on the control unit.

4.5 Enabling the Automatic Start Mode

This Automatic Start Mode allows the control unit to

launch a pre-selected cleaning cycle triggered by an

external source (timer / programming clock).

The cycle can be either "Cycle I" or "Cycle II”.

The 9300xi Sport will run for 2.5 hours.

It is not possible to change the running time when

operating in this mode.

Procedure for launching a cycle with

a programming clock (timer):

1. Connect the control unit to the receptacle.

2. To automatically start the “Cycle I”, press the

following button for more than three (3) seconds:

+ Cycle I

3. To automatically start the "Cycle II”, press the

following button for more than three (3) seconds:

+ Cycle II

4. The two (2) lights will ﬂ ash once

5. The robot will start automatically when it is

powered on.

Rotate Left

Forward

Reverse

Rotate Right

6. Remove the ﬁ lter assembly from the body (3), as

shown in Figure 22.

7. Push the quick release button on the canister

assembly (4) and pull open the ﬁ lter assembly (5).

Refer to Figure 23.

8. Separate the ﬁ lter canister from the ﬁ lter support

(6), as shown in Figure 24.

9. Wash the ﬁ lter canister, the ﬁ lter support, and the

cleaner under water or using a hose (7). Refer to

Figure 25.

Section 5. Cleaning and Maintenance

WARNING

To avoid electric shock and other hazards which

could result in permanent injury or death, disconnect

(unplug) the cleaner from the control unit before

performing any cleaning and maintenance.

5.1 Cleaning the Filter Canister

The ﬁ lter canister should be cleaned at the end of each

cycle.

1. Ensure that the control unit cable has been

disconnected from the electrical outlet or that the

ﬂ oating cable has been disconnected from the

control unit.

2. Remove the cleaner from the water and let the

remaining water drain by maintaining the cleaner

in the vertical position.

3. Set the unit on its wheels.

4. To remove the ﬁ lter from the cleaner, follow the

steps 1 through 6 (Figures 21 through 24).

5. Push the cover lock (1) and lift the cover (2) until

it is secured in the vertical position. Refer to

Figure 21.

English

Page 12

5.2 Cleaning and Storing the Cleaner

The cleaner must be cleaned regularly using slightly

soapy clean water, do not use solvents such a trichloro-

ethylene or its equivalent. Rinse the cleaner generously

using clean water. Do not let your cleaner dry in direct

sunlight near the pool. The cleaner must be stored on its

own caddy, so that it dries quickly.

1. Place the rear wheels on the caddy side wedges as

shown in Figure 26.

Figure 22. Remove Filter Assembly

Figure 23. Open Filter Assembly

Figure 24. Remove Filter Canister

Figure 25. Wash Filter Canister

2. Roll the unit into place onto the caddy. Refer to

Figure 27.

NOTE The cleaner cable must be disconnected from

the control box before removing the cleaner from

the pool. Wrap the cleaner cable around the

hooks located at the rear of the caddy.

Figure 26. Position Cleaner on Caddy

Figure 27. Roll Cleaner onto Place on the Caddy

English

Page 13

2. Separate the edges of the brush and undo the tabs

as shown is Figure 29. Remove the worn brushes.

Figure 28. Clean in Upright Position

3. To install a new brush, position the new brush on

the roller with the spikes facing downwards. Refer

to Figure 30.

4. Thread each tab into the slot provided and gently

feed it through until the heel comes out at the

other side of the slot. Refer to Figure 31.

5. Use a pair of scissors to cut the tabs 3/4 inch from

the heel so that they are no higher than the spikes

as shown in Figure 32.

6. Repeat this procedure to install the second brush.

Figure 29. Undo the Tabs of the Brush

Figure 30. Install the New Brush

Figure 31. Pull Tabs Through Each Slot

Figure 32. Cut Tabs

5.3 Replacing the Brushes

The cleaner is ﬁ tted with PVC brushes. There are ''wear''

indicators on the brushes. To maintain cleaner perfor-

mance at its best you need to replace the brushes as soon

as one of the wear indicators has been reached (even if

the blade wear is not even). Zodiac Pool Systems, Inc.

recommends that you replace the brushes every two (2)

years.

1. Lift the cleaner to a vertical position so that the

handle is up. Refer to Figure 28.

English

Page 14

5.4 Replacing the Tires on the Cleaner

1. Pull on the inside of the old tire to remove the tire

lip from the wheel. See Figure 33.

2. Remove the old tire as shown in Figure 34.

3. To replace the tire, position the tire on the wheel

making sure to orient the tire so that the tread is on

the outer side of the wheel. See Figure 35.

4. Push one side of the tire on to the wheel and ﬁ t the

rib of the tire in the groove of the wheel as shown

in Figure 36.

5. Work the tire onto the wheel and verify the rib of

the tire is positioned properly within the groove of

the wheel. Refer to Figure 37.

Push and position the rib of the inner side of the

tire in the groove of the wheel. Refer to

Figure 38.

If needed, turn the wheel gently to help with

installation.

Figure 33. Pull the Old Tire Over the Wheel

Figure 34. Remove the Old Tire

Figure 37. Work the Tire On Around the Wheel

Figure 36. Start on One Side of the Tire

Figure 35. Tire Replacement Orientation

Figure 38. Push the Tire into Place on the Wheel

English

Page 15

Symptom Cause Solution

The ﬂ ashing indicator

lights appear just after

start (pressing the Power

or Cycle button to start the

cleaner) (< 20 seconds).

Ensure the ﬂ oating cable is properly

plugged into the control unit.

Unplug the ﬂ oating cable from the control unit and

plug it again properly.

Ensure the cleaner is well sub-

merged.

Submerge the cleaner following the procedure in

Section 4.1, "Submerging the Cleaner".

Cleaner needs to be reset and start

new cycle.

Press the power button OFF and then Cycle I or II

Program buttons to start new cycle.

Propeller does not turn. Please contact your local Polaris service represen-

tative.

Wheels do not turn. Please contact your local Polaris service represen-

tative.

The ﬂ ashing lights appears

during the cycle.

If the cleaner sucks air for 60 sec-

onds, the ﬂ ashing light appears.

Submerge the cleaner following the procedure in

Section 4.1, "Submerging the Cleaner".

The cleaner does not stay

ﬁ rmly on the pool bottom.

There is air in the appliance casing. Submerge the cleaner following the procedure in

Section 4.1, "Submerging the Cleaner".

The cleaner does not or no

longer climbs the pool sides.

The ﬁ lter is full or dirty. Clean the ﬁ lter canister following the procedure

Section 5.1, "Cleaning the Filter Canister".

Sides of pool are slippery or slimy.

Although the water seems clear,

microscopic algae, invisible to the

human eye, are present in the pool.

As a result the pool sides become

slippery and prevent the cleaner from

climbing.

Do a shock chlorination treatment and slightly re-

duce the pH. DO NOT leave the cleaner in the pool

during this treatment.

On startup the cleaner does

not move.

Not supplied with electricity. The outlet, the control unit is connected to, is not

supplying electrical power. Check that the outlet

to which the control unit is connected is receiving

electricity.

Unit is turned ON. Check that you have started one (1) of the two (2)

programs and check that the indicator for the se-

lected program is lit. If the problem persists, contact

your local Polaris service representative.

The cycle I and II program

indicators ﬂ ash alternately.

Your cleaner has encountered a

problem or a issue during its opera-

tion.

Disconnect the control unit and wait 20 seconds

before reconnecting the control unit. Check that

the cable is correctly connected to the control unit.

Check that no debris impedes the rotation of the

brushes and/or the propeller. Clean the ﬁ lter. Start

a new cleaning program. If the problem continues

contact your local Polaris service representative.

The cleaner seems to be

performing less efﬁ ciently.

The brushes have become smooth. Replace the brushes following the procedure in

Section 5.3, "Replacing the Brushes".

Filter canister is full or dirty. Clean the ﬁ lter canister following the procedure in

Section 5.1, "Cleaning the Filter Canister".

Floating cable is excessively coiled or

kinked.

Make sure the ﬂ oating cable is spread out over the

pool.

Section 6. Troubleshooting

6.1 General Troubleshooting

Table 1 lists some of the more common symptoms, causes and solutions encountered when using the cleaner. The unit

employs ﬂ ashing lights during Cycle I and II to indicate different issues on the control unit and on the cleaner. These

indications are not necessarily major issues. To turn off the ﬂ ashing light, press the power button. Then start a new cycle:

If the ﬂ ashing lights persist after completing troubleshooting, please contact your retailer. DO NOT open the control unit.

English

Page 16

Section 7. Polaris 9300xi Sport Exploded View and Replacement Parts List

Key No. Part No. Description Qty.

23 R0518600 Float Kit 1

24 R0518700 Brush Separator 1

25 R0518800 Drive Gear Kit 2

26 R0519000 Ramp Kit 1

CONTROL UNIT

27 R0528400 Keyboard PCB Kit 1

28 R0506600 Control Unit PCB Kit 1

29 R0528500 Top Housing 1

30 R0506800 Control Unit Cord Kit 1

31 R0507000 PCB Screw Kit 6

32 R0507100 Control Unit Housing Screw 8

33 R0507200 Control Unit Gasket 1

34 R0506800 Power Cord Kit 1

CADDY

35 R0507300 Caddy Handle Grip Kit 1

36 R0516100 Caddy Shoulder Grip Kit 1

37 R0518900

Control Unit Mounting

Bracket Kit

38 R0507500 Wheel Kit Caddy 1

REMOTE CONTROL

39 R0529600 Remote Control Kit 1

Symptom Cause Solution

The remote control does not

work.

The batteries are dead and need to

be replaced.

Replace the batteries in the remote control.

The remote control is not

synchronized to the control unit.

Synchronizing procedure:

When replacing the control unit or the remote con-

trol, it is necessary to synchronise the new remote

control with the control unit:

1. Connect the 9300xi sport to the control unit,

then plug the control unit to the receptacle.

2. Press OFF + Cycle I buttons for more

than 6 seconds until both lights

ﬂ ash once:

3. Press and hold the "rotate right" button on the

remote control unit.

4. The light on the right will ﬂ ash

5 times

then both

lights

will ﬂ ash together.

5. The synchronization procedure is completed

when both lights switch off.

English

7.1 Parts List

Key No. Part No. Description Qty.

CLEANER

1A R0516200 Caddy 1

2A R0528600 Control Unit Complete 1

3 R0516600 Main Housing (Top & Bottom) 1

4 R0516700 Motor Block Screw Kit 22

5 R0528700 Cable (Floating) 1

6 R0528800 Motor Block 1

7 R0517000 Propeller 1

8 R0517100 Complete Cover 1

9 R0517200

Transmission Gear/Bushing,

2 sets

10 R0528900 Brush Set (Set of 2) 1

11 R0517400 Roller Kit (Set of 2) 1

12 R0517500 Flow Outlet 1

13 R0517600 Flow Outlet Screen 1

14 R0517700 Filter Canister Support 1

15 R0517800 Filter Canister 1

16 R0529000 Front Wheel w/ Tire 1

17 R0529100 Rear Wheel w/ Tire 1

18 R0518100 Roller Kit (Set of 2) 1

19 R0529200

Motor Housing Cover Kit

(w/ O-Ring)

20 R0529300 Front Tire 1

21 R0529400 Rear Tire 1

22 R0518500

Wheel Bushing

(1 set for 1 wheel)

Page 17

7.2 Exploded View

English

Control Unit - 2A

Caddy - 1A

Cleaner

Page 18

W2093A Rev A

Zodiac Pool Systems, Inc.

2620 Commerce Way, Vista, CA, 92081 USA • 800.822.7933 • FAX 877.327.1403

Conforms to UL 1081

Certiﬁ ed to CSA E63055-2-41

English

ZODIAC

is a registered trademark of Zodiac International, S.A.S.U.,

used under license. All other trademarks used herein are the property

of their respective owners.

Page is loading ...

Page 35

W2093A RévA

Zodiac Pool Systems, Inc

2620 Commerce Way, Vista, CA, 92081 USA • 800.822.7933 • FAX 877.327.1403

CONFORME À LA NORME UL 1081

Certiﬁ é CSA E63055-2-41

ZODIAC

est une marque de commerce déposée de Zodiac International, S.A.S.U.,

utilisée sous licence. Toutes les autres marques de commerce mentionnées sont la

propriété de leurs propriétaires respectifs.

Français

Page is loading ...

Page 52

W2093A RevA

ZODIAC

es una marca registrada de Zodiac International,

S.A.S.U., usada bajo licencia. Todas las otras marcas

registradas usadas aqui son propiedad de sus propietarios.

Español

Zodiac Pool Systems, Inc

2620 Commerce Way, Vista, CA, 92081 USA • 800.822.7933 • FAX 877.327.1403

Conforms to UL 1081

Certiﬁ ed to CSA E63055-2-41

Polaris 9300xi Sport Owner's manual

Brand: Polaris

Model: 9300xi Sport

Category: Above ground pool accessories

Type: Owner's manual

Download PDF

report

in other languages

français: Polaris 9300xi Sport Le manuel du propriétaire
español: Polaris 9300xi Sport El manual del propietario

Polaris 9300xi Sport Owner's manual

Polaris 9300xi Sport Owner's manual

in other languages

Related papers

Other documents