5019 401 05268
Add the detergent as described in the chapter “Detergent
and Additives” in the instructions for use.
1. Turn the
programme selector knob
to the desired
programme.
2. The
remaining time display
shows the duration of
the chosen programme (in hours and minutes), and the
lamp over the
“Start”
button flashes.
3. The
programme sequence indicator
and the
predefined spin speed indication corresponding to the
selected programme lights up.
The recommended temperature (see the indicator)
can be altered by pressing the temperature selection
button under the temperature display.
•Wash your laundry in the desired programme (Cotton,
Synthetics), adding an appropriate amount of chlorine
bleach to the SOFTENER chamber (close the
detergent dispenser carefully).
• Immediately after end of programme, start the “Rinse
and Spin” programme to eliminate any residual bleach
smell; if you want, you can add softener.
“Eco +” button
• With a modified temperature profile and a slightly
prolonged washing duration, the optimum
combination of excellent washing result and even
lower energy consumption can be achieved.
“Prewash” button
• Only for heavily soiled laundry (e.g. sand or granular
dirt). Programme duration is increased by some
15 min.
“Intensive Rinse” button
• An additional rinse cycle is carried out.
• This option is particularly suitable for areas with very
soft water, washing baby linen and helps people with
detergent allergies.
“Rinse Hold” button
• The laundry remains in the last rinse water without
being spun: discoloration of the laundry and additional
creasing are prevented.
• This option is particularly recommended for the
programme “Synthetic” or “Delicate”.
• This function is particularly useful if you want to
postpone spinning to a later time.
Note:
The programme has reached the “Rinse Hold”
when the corresponding light flashes.
Terminate the “Rinse Hold” option:
• Press the “Rinse Hold” button again; the programme
will terminate automatically with the appropriate spin
cycle for the current programme.
CONSUMPTION DATA
*
Programme Temperature
(°C)
Wash
(kg)
Water
(l)
Energy
(kWh)
Programme duration
approx.**
(hours : minutes)
Cotton White/Hygiene+
95 6.0 49
***
1.90 2:00
Cotton Colours
60 6.0 44 1.14 2:20
Cotton with “Eco +” ****
60 6.0 44 1.02 2:30
Cotton Colours
40 5.0 42 0.70 2:05
Synthetics
60 2.5 60
***
0.90 1:45
Synthetics
40 2.5 55 0.60 1:30
Daily Load
40 3.0 48 0.55 1:00
Quick Wash
30 3.0 37 0.30 0:30
Delicate
30 1.5 60 0.50 0:45
Wool
40 1.0 60 0.50 0:40
Dessous / Handwash
30 1.0 45 0.40 0:35
Easy Ironing
40 3.0 60 0.60 1:30
*
The
consumption values
were measured in normalized conditions in compliance with Standard IEC/EN 60456.
**
The
programme duration
may also vary from the chart values. The washing machine is able to allow for particular
household conditions and to adapt the programme run time accordingly.
***
To reduce the
water temperature
, some cold water is added at the end of the main wash cycle, before the pump
drains the water out.
****
Reference programme for energy label.
POUR IN DETERGENT, CLOSE THE
DOOR AND SELECT A PROGRAMME
USING CHLORINE BLEACH
SELECT SPECIAL OPTIONS -
The corresponding lights go on (if not
selectable: rapid flashing for 3 seconds)
• If you do not wish to spin the clothes, turn the
programme selector knob to “Drain” and press the
“Start”
button again.
“Spin Speed Reduction” button
• A maximum spin speed is assigned to each
programme.
• Press the button to set another speed for the spin
cycle.
• If no light goes on, the final spin is cancelled.
The water is only drained out.
With the “Start Delay” function the appliance can be run
cheaply e.g. at night, when the electricity is cheaper.
• Press the “Start Delay” button. Select the programme
start from 1 to 24 hours ahead by pressing the button
again.
• Press the
“Start”
button.
The Start Delay indicator light flashes until the
programme starts.
“Start Delay” correction.
• Before “Start” has been pressed:
The preset number of hours can be altered by
continuously pressing the “Start Delay” button.
By pressing the Start Delay button again after the “24”
setting, the time delay can be deleted again or set
again.
After “Start” has been pressed:
The preset number of hours can be reduced by
pressing the “Start Delay” button again; please note,
however, that the washing programme starts
IMMEDIATELY, as soon as you operate it again with
the Start Delay switch 01 setting.
To increase the number of hours preselected, first turn
the programme selector switch to the “Off” position.
Then set the programme and the additional options
again and select the desired number of hours.
After you have selected the programme and eventually the
additional options, the indicator light over the
“Start”
button flashes. Turn on the tap and start the programme
by pressing the
“Start”
button. Now the indicator light
over the button goes on.
In addition, all programme phases are indicated by the
associated lights. After the end of a programme phase, the
associated indicator light goes out. Thus the programme
sequence indicator moves from left to right across the
wash, rinse and spin phases. At the end of the programme,
only the “End” indicator is still on.
As long as a washing programme is running, the lamp lights
up to show that the door cannot be opened. When the
lamp goes off, the door can be opened again.
If
“Start”
has been pressed, but the door is not latched,
the “Door Locked” indicator flashes for 10 seconds. The
door must be pushed shut within this time.
After the 10 seconds, the “Door Locked” indicator goes
out and the
“Start”
button flashes. The door must then
be opened and closed again and the
“Start”
button must
be pressed.
“Pump”
Waste water is not pumped out. Check wether the drain
hose is kinked or the filter must be cleaned; in the latter
case refer to the Instructions for Use (“Removing the
Filter”).
“Water Tap”
The appliance has no or insufficient water supply. Open
the water tap; if the indication still lights up, refer to the
“Troubleshooting Guide” in the Instructions for Use.
“Aquastop”
Lighting up of the Aquastop indication can be caused by a
leak in the appliance or hose. Please refer to the
“Troubleshooting Guide” in the Instructions for Use.
• The “End” indicator goes on.
1. Switch the washing machine off by turning the
programme selector to the “
O
”-position.
2. Turn off the tap.
3. Open the door and unload the machine.
A newly-selected programme will continue in the same
programme section during which the current programme
was interrupted. Therefore do not add any more
detergent.
1. Press the
“Start”
button to interrupt the programme.
The light flashes.
2. Select the new programme (with temperature), any
additional options and - if you wish - another spin
speed.
3. Press the
“Start”
button again to restart the
programme.
• If you are in the “Prewash” programme step, this
additional option cannot be deselected as described
(to do this see “Cancel/Reset a running programme
before the end”).
Press the
“Reset”
button for at least 2 seconds. Any
existing water is drained out before the door can be
opened.
START DELAY
PROGRAMME START
“DOOR LOCKED” INDICATOR
“TROUBLE” INDICATORS
PROGRAMME END
RESELECT AFTER PROGRAMME START
CANCEL (RESET) A RUNNING
PROGRAMME BEFORE THE END
40105268GB.fm Page 2 Wednesday, October 26, 2005 12:19 PM
Black process 45.0° 100.0 LPI
