Bauknecht WA 2362 Program Chart

Brand: Bauknecht

Model: WA 2362

Type: Program Chart

1) Appliances with max. spin speed greater than 900 rpm: for improved garment care, spin speed is restricted to 900 rpm.

2) The programme duration figures are approximate values for a programme with maximum temperature but without special options.

Programme Care label Type of fabric /

Degree of soiling

Max. Load Detergent

and Additives

Options =

❉

Thermostat

knob

Programme

Selector

Programme

Duration

Notes

Softener Main

Wash

Pre-

wash

Half

Load

Short Intensive

Rinse

Hold

Pre-

Wash

Spinning

kg °C

approx.

Min.

Cotton /

Cotton

Coloured

Lightly to averagely soiled bed

linen, table linen, underwear,

towels, shirts etc. (linen and

cotton) etc.

Normal 6.2

Rapid 3.0

❉

yes

❉❉❉❉❉❉❉

From “ ”

to 95

Short: From

“ ” to 60

120

If “Short” is selected the options

“Intensive Rinse” and “Prewash”

are inhibited.

Easy care

Lightly to averagely soiled

blouses, shirts, etc. made of

polyester (Diolen, Trevira),

polyamide (Perlon, Nylon) or

blends with cotton.

Normal 2.5

Rapid 1.5

❉

yes

❉❉❉❉❉❉❉

From “ ”

to 60

Short: From

“ ” to 60

If “Short” is selected the options

“Intensive Rinse” and “Prewash”

are inhibited.

Delicates

Curtains, delicate dresses, skirts,

shirts and blouses.

1.5

❉

yes

❉

———

❉❉❉

From “ ”

to 40

—

Wool

Only machine washable woollens

with pure new wool label.

1.0

❉

yes

————

❉

—

❉

From “ ”

to 40

If you select the special option

“Rinse Hold” don’t leave garments

to soak for too long.

Rinse + Spin

—

6.2

❉

——

❉

——

❉

—

❉

“”

—

Programme for treating wash with

starch or softener. Terminates with

an intensive spin cycle, same as

the spin cycle in the Cotton

Coloured programme.

Gentle Spin

—

6.2

————————

❉

——

Programme for gentle spin cycle,

same as the spin cycle in the Wool

programme.

Draining

—

—————————— —

Drain only without spin cycle.

Alternative way of terminating

programmes with “Rinse hold”

setting.

Indicator: Door lock

Indicator: Water tap

PROGRAMME TABLE

2B 5019 100 03864

is a registered trademark

Indicator:

Wash Rinse Spin

WA 2362

Prewash cycle increases programme duration by approx. 15 minutes.

Consumption data were measured in normalised conditions in compliance with Standard IEC 60 456.

Consumption data in the home may vary with respect to the values in the table in relation to the water supply

pressure and temperature, the load and the type of wash.

ROUTINE WASHES:

1. Turn on the tap.

2. Sort the laundry according to fabric type and colour and load the machine.

3. Close the door.

4. Pour in detergent and additives.

5. Select the programme, the temperature and any special options you require.

6. Hold down the “Start” button for about one second.

NOTE:

During the first 15 minutes of Cotton and Easy Care programmes (each without Prewash)

you can open the door to add items to the wash. This is not possible when the special

function “Short” is selected.

TO INTERRUPT THE PROGRAMME:

To interrupt a programme that is already running and then continue later:

1. Set the programme selector knob to “0”.

2. After the required break, reselect the programme.

3. Hold down the “Start” button for about one second.

The programme will continue from where it was interrupted.

CHANGING PROGRAMME DURING A RUNNING PROGRAMME:

a) TO SELECT A NEW PROGRAMME OR A DIFFERENT TEMPERATURE AND

CONTINUE

1. Select a new programme and/or new temperature.

2. Hold down the “Start” button for about one second.

The new programme will continue from the same programme step where the running

programme was interrupted.

b) TO CANCEL A PROGRAMME THAT IS ALREADY RUNNING AND START A

DIFFERENT PROGRAMME FROM THE BEGINNING

There’s no need to add more detergent when you start the new programme, because

the appliance drains only just few water when you cancel the current programme.

1. Hold down the “Start” button for five seconds, or until the programme control

audibly restarts.

2. Wait until the programme sequence indicator returns to its initial position on the left

(no longer visible).

3. Set the programme selector to “0”.

4. Set the programme selector knob to the new programme, select the temperature

(if different) and any different special options you require.

5. Hold down the “Start” button for about one second.

TROUBLE-SHOOTING GUIDE:

The appliance is equipped with safety functions able to identify and indicate the presence

of faults and react appropriately.

Most faults are minor problems that can be solved quickly. The following list gives several

examples:

• The appliance fails to start.

• The appliance stops in mid programme.

• No water or insufficient water supply.

• The appliance does not drain.

• The machine vibrates during the spin cycle.

• Final spin results are poor.

• Detergent and additive product residues in the detergent dispenser at end of wash.

The cause and action notes for the above points are given in the instruction for use in the

chapter “Trouble-shooting guide”.

Programme

Thermostat

knob

Maximum

load

Special options Water Electricity

Programme

duration

(°C) (kg) (l) (kWh) (min.)

Cotton / Cotton Coloured 95 5.0 — 60 1.80 120

Cotton / Cotton Coloured 60 5.0 — 55 1.20 115

Cotton / Cotton Coloured 60 2.5 Saving half load 40 0.90 100

Cotton / Cotton Coloured 40 5.0 — 55 0.60 100

Cotton / Cotton Coloured 30 3.0 Short 35 0.30 55

Easy care 60 2.5 — 60 0.90 85

Easy care 40 2.5 — 54 0.40 70

Easy care 30 1.5 Short 25 0.20 35

Delicate 40 1.5 — 60 0.50 40

Wool 40 1.0 — 60 0.50 35

Power and water consumption data

Bauknecht WA 2362 Program Chart

Bauknecht WA 2362 Program Chart

Bauknecht WA 2362 Program Chart

Related papers

Other documents