Metropolitan N2921-1-77 User manual

Metropolitan
Brand
Metropolitan
Model
N2921-1-77
Type
User manual

Metropolitan N2921-1-77

This lighting fixture is designed for indoor use and can be mounted on a wall. It comes with a crossbar that attaches to the outlet box, and a nipple that threads into the center hole of the crossbar. The fixture body is then placed over the nipple and secured using a finial. The fixture includes a glass panel that is held in place by a stud and cap nut.

According to the installation instructions, the fixture can accommodate one light bulb, but the maximum wattage rating is not specified. The fixture is likely compatible with LED bulbs, CFL bulbs, and incandescent bulbs, as long as they do not exceed the maximum wattage rating.

Metropolitan N2921-1-77

This lighting fixture is designed for indoor use and can be mounted on a wall. It comes with a crossbar that attaches to the outlet box, and a nipple that threads into the center hole of the crossbar. The fixture body is then placed over the nipple and secured using a finial. The fixture includes a glass panel that is held in place by a stud and cap nut.

According to the installation instructions, the fixture can accommodate one light bulb, but the maximum wattage rating is not specified. The fixture is likely compatible with LED bulbs, CFL bulbs, and incandescent bulbs, as long as they do not exceed the maximum wattage rating.

INSTALLATION INSTRUCTIONS
Item#N2921-1-77 (Rev. 11/25/2015)
READ AND SAVE THESE INSTRUCTIONS
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
Fig. 2
Fig. 1
ASSEMBLING THE FIXTURE (Fig. 1 )
1. Shut off power at the circuit breaker and remove
old fixture from wall, including the crossbar.
2. Carefully unpack your new fixture and lay out all
the parts on a clear area. Take care not to lose
any small parts necessary for installation.
3. Attach the Crossbar (A) to the Outlet box using
the two Screws (B). The side of the Crossbar
marked “GND” must fact out.
4. Thread the Nipple (C) part way into the center
hole of the crossbar.
CONNECTING THE WIRES (Fig. 2)
5. At this point, connect the electrical wires as
shown in Fig. 2, making sure that all wire
connectors are secured. If your outlet has a
ground wire (green or bare copper), connect the
fixture’s Ground Wire to it. Otherwise, connect
the fixture’s Ground Wire directly to the
mounting plate using the Green Screw
provided. After wires are connected, tuck them
carefully into the outlet box.
FINISH THE INSTALLATION (Fig.1)
6. Place the Fixture body (D) over the Nipple (C)
and secure them using Finial (E).
7. Install the light bulb in accordance with the
fixture’s specifications. (DO NOT EXCEED
THE MAXIMUM WATTAGE RATING!). (NE
PAS DEPASSER LA PUISSANCE NOMINALE
MAXIMALE!)
8. Finish mounting Glass Panel (G) by aligning
hole (H) on glass panel to Stud (F) on metal
frame of fixture body, then place Bushing (I)
over Stud and secure them with Cap nut (J).
Your installation is now complete. Return power to
the outlet box and test the fixture.
Note: Illustration (Fig. 1) on this manual is for
installation purposes only. It may or may not
be identical to the fixture purchased.
LA-1308E
FIXTURE
WIRES
Black or
Smooth
H
O
USE
WIRES
Black
(Hot)
FIXTURE
WIRES
White or
Ribbed
H
O
USE
WIRES
White
(Neutral)
FIXTURE
WIRES
Bare
Copper
(Ground)
H
O
USE
WIRES
Green
(Ground)
C
B
A
H
G
F
J
I
E
D
“© Minka Lighting, Inc.
This product is protected by United States Federal and/or
State Law, including Patent and/or Copyright laws.”
  • Page 1 1

Metropolitan N2921-1-77 User manual

Metropolitan
Brand
Metropolitan
Model
N2921-1-77
Type
User manual

Metropolitan N2921-1-77

This lighting fixture is designed for indoor use and can be mounted on a wall. It comes with a crossbar that attaches to the outlet box, and a nipple that threads into the center hole of the crossbar. The fixture body is then placed over the nipple and secured using a finial. The fixture includes a glass panel that is held in place by a stud and cap nut.

According to the installation instructions, the fixture can accommodate one light bulb, but the maximum wattage rating is not specified. The fixture is likely compatible with LED bulbs, CFL bulbs, and incandescent bulbs, as long as they do not exceed the maximum wattage rating.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents