Samsung 930MP User manual

SyncMaster 930MP

Failure to follow directions noted by this symbol could result in bodily harm or damage to

equipment.

Prohibited Important to read and understand at all times

Do not disassemble Disconnect the plug from the outlet

Do not touch Grounding to prevent an electric shock

Power

When not used for extended period of time, set your computer to DPMS.

If using a screen saver, set it to the active screen mode.

Do not use a damaged or loose plug.

z

This may cause an electric shock or fire.

Do not pull the plug out by the wire nor touch the plug with wet hands.

z This may cause an electric shock or fire.

Use only a properly grounded plug and receptacle.

z

An improper ground may cause electric shock or equipment damage.

Do not excessively bend the plug and wire nor place heavy objects upon them,

which could cause damage.

z This may cause an electric shock or fire.

Do not connect too many extension cords or plugs to an outlet.

z

This may cause fire.

Installation

Put your monitor in a location with low humidity and a minimum of dust.

z Failure to do so may cause an electric shock or fire inside the monitor.

Do not drop the monitor when moving it.

z

This may cause damage to the product or human body.

Place the monitor on a flat and stable surface.

z The monitor may cause injury by falling.

Set down the monitor carefully.

z

The monitor could be damaged or broken.

Do not place the monitor face down.

z The TFT-LCD surface may be damaged.

Installing a wall bracket must be done by a qualified professional.

z

Installation by unqualified personnel may result in injury.

z

Always use the mounting device specified in the owner's manual.

Leave a space for ventilation between the product and the wall.

z Poor ventilation may cause the interior temperature to rise and lead to fire.

To prevent rainwater from running along the outdoor antenna cable and entering the

house, be sure the outdoor portion of the cable hangs down below the point of entry.

z If rainwater enters the product, it may cause an electric shock or fire.

If you are using an outdoor antenna, be sure to put sufficient distance between your

antenna and the electrical wires nearby so that they would not come in contact with

each other in case the antenna is knocked over by strong wind.

z A knocked-over antenna may cause injury or an electric shock.

Clean

When cleaning the monitor case or the surface of the TFT-LCD screen, wipe with a

slightly moistened, soft fabric.

Do not spray water or detergent directly on the monitor.

z This may cause damage, electric shock or fire.

Use the recommended detergent with a smooth cloth.

If the connector between the plug and the pin is dusty or dirty, clean it properly

with a dry cloth.

z A dirty connector may cause an electric shock or fire.

Contact a Service Center or Customer Center for interior cleaning once a year.

z

Keep the product's interior clean. Dust which has accumulated in the interior

over an extended period of time may cause malfunction or fire.

Others

Do not remove cover (or back). No user serviceable parts inside.

z

This may cause an electric shock or fire.

z

Refer servicing to qualified service personnel.

If your monitor does not operate normally - in particular, if there are any

unusual sounds or smells coming from it - unplug it immediately and contact

an authorized dealer or service.

z This may cause an electric shock or fire.

Be careful not to let water drip into the monitor or expose the monitor to

moisture.

z This may cause malfunction, an electric shock or fire.

z Especially avoid operating the monitor near water or outdoors where it could

be exposed to snow or rain.

If the monitor is dropped or the casing is damaged, turn the monitor off and

unplug the power cord.

z The monitor may malfunction, causing an electric shock or fire.

z Then contact the Service Center .

Disconnect the plug from the outlet during storms or lightening or if it is not

used for a long period of time.

z

Failure to do so may cause an electric shock or fire.

Do not try to move the monitor by pulling only the wire or the signal cable.

z

This may cause a breakdown, electric shock or fire due to damage to the

cable.

Do not move the monitor right or left by pulling only the wire or the signal

cable.

z This may cause a breakdown, electric shock or fire due to damage to the

cable.

Do not cover the vents on the monitor cabinet.

z Bad ventilation may cause a breakdown or fire.

Do not place water containers, chemical products or small metal objects on

the monitor.

z This may cause malfunction, an electric shock or fire.

z If a foreign substance enters the monitor, unplug the power cord and contact

the Service Center .

Do not use or store inflammable substances near the monitor.

z This may cause an explosion or fire.

Never insert anything metallic into the monitor openings.

z

This may cause an electric shock, fire or injury.

Do not insert metal objects such as utensils, wire or drill bits, or things that

catch fire easily, such as pieces of paper or matches, into the vents, or the

headphone, or A/V ports on the monitor.

z This may cause malfunction, an electric shock or fire.

z Always contact the Service Center if foreign substances/objects enter into the

monitor.

If you view a fixed screen for an extended period of time, residual image or

blurriness may appear.

z Change the mode to energy save or set a screensaver to moving picture when

you need to be away from the monitor for an extended period of time.

Adjust the resolution and frequency to the levels appropriate for the model.

z Inappropriate resolution may cause undesirable picture quality.

19 inch - 1280 X 1024

Be careful that adapter should not be in contact with water and therefore not

be wet.

z

This may cause malfunction, an electric shock or fire.

z Do not use adapter by the waterside or outside particularly when it rains or

snows.

z Be careful that adapter should not be wet while cleaning floor with water.

Keep all power adapters apart.

z Failure to do so may cause fire.

Keep power adapter away from any other heat source.

z Failure to do so may cause fire.

Remove and discard vinyl bag from power adapter before use.

z

Failure to do so may cause fire.

Always keep power adapter in well-ventilated area.

Keep the volume at a proper level when you use the headphones.

z Excessively loud volume levels may damage hearing.

Keep a proper distance between your eyes and the monitor screen.

z Sitting too close to the monitor on a continuous basis may damage eyesight.

To ease eye strain, take at least a five-minute break after every hour of using

the monitor.

Do not use the monitor where it may be exposed to strong vibrations.

z

Exposure to strong vibrations may be fire hazard and shorten the life of the

monitor.

When moving the monitor, turn the power switch off and unplug the power

cord.

Make sure that all cables, including the antenna cable and cables connecting

to other devices, are disconnected before moving the monitor.

z

Failure to disconnect a cable may damage it and lead to fire or an electric

shock.

When you remove batteries from the remote, be careful that they are not

swallowed by children. Keep batteries out of the reach of children.

z If swallowed, see a doctor immediately.

When replacing batteries, place the batteries in the correct +/- polarity position

as indicated on battery holder.

z Incorrect polarity may cause a battery to break or leak and could lead to fire,

injury, or contamination (damage).

Use only specified standard batteries. Do not use new and used batteries

together.

z This may cause a battery to break or leak and could lead to fire, injury, or

contamination (damage).

Do not set a glass of water, chemicals or any small metal objects on the

monitor.

z This may cause damage, electric shock or fire.

z If a foreign substance gets into the monitor, disconnect the plug and then

contact a service center.

Please make sure the following items are included with your monitor.

If any items are missing, contact your dealer.

Contact a local dealer to buy optional items.

Unpacking

Monitor

Manual

Quick Setup Guide

Warranty Card

(Not available in all locations)

User's Guide, Monitor Driver,

Natural Color software

Cable

D-Sub Cable Power Cord Radio Antenna

Audio Cable DC Adapter

Sold separately

DVI Cable(option)

Others

Remote Control Batteries (AAA X 2) Connecter

Front

1. MENU

2. AUTO

3. ENTER/FM RADIO

4. SOURCE

5. PIP

6. MagicBright™

7. CH

8. + VOL -

9. Power button / Power indicator

10. Remote Control Sensor

1. MENU

Use this button for open the on-screen menu and exits from the menu screen or closes

screen adjustment menu.

2. AUTO

Use this button for auto adjustment.

If you change resolution in the control panel, Auto function will be executed.

>>Click here to see an animation clip

3. ENTER / FM RADIO

ENTER : Activates a highlighted menu item.

FM RADIO : In areas where signal is weak, noise may occur while FM radio is broadcast.

>>Click here to see an animation clip

4. SOURCE

Switches from PC mode to Video mode.

Changing the source is allowed only external devices that are connected to the monitor at

the time.

To switch Screen modes:

[PC] [DVI] [TV] [Ext.] [AV] [S-VIDEO] [Component]

>>Click here to see an animation clip

NOTE : According to broadcasting type in each country, you may not be able to select one.

Scart is mainly used in Europe.

For more information > Broadcasting Systems

5. PIP ( Available in PC/DVI Mode Only )

In PC Mode, turns on Video or TV screens in PIP Mode.

>>Click here to see an animation clip

6. MagicBright™ [ ] ( Available in PC/DVI Mode Only )

MagicBright™ is a new feature providing optimum viewing environment depending on the

contents of the image you are watching. Currently four different modes are available:

Custom, Text, Internet, and Entertain. Each mode has its own pre-configured brightness

value. You can easily select one of four settings by simply pressing MagicBright™ control

buttons.

1) Text : Normal Brightness

For documentations or works involving heavy text.

2) Internet : Medium Brightness

For working with a mixture of images such as text and graphics.

3) Entertain : High Brightness

For watching motion pictures such as a DVD or VCD.

4) Custom

Although the values are carefully chosen by our engineers, the pre-configured values

may not be comfortable to your eyes depending on your taste.

If this is the case, adjust the Brightness and Contrast by using the OSD menu.

>>Click here to see an animation clip

7. CH

Moves from one menu item to another vertically or adjusts selected menu values. In TV

mode, selects TV channels.

>>Click here to see an animation clip

8. + VOL -

Moves from one menu item to another horizontally or adjusts selected menu values. Also

adjusts the audio volume.

>>Click here to see an animation clip

9. Power button / Power indicator

Use this button to turn the monitor on and off./ Power Indicator shows PowerSaver mode

by green blinking.

10. Remote Control Sensor

Aim the remote control towards this spot on the Monitor.

See PowerSaver described in the manual for further information regarding power saving functions.

For energy conservation, turn your monitor OFF when it is not needed or when leaving it unattended

for long periods.

Rear

(The configuration at the back of the monitor may vary from product to product.)

1. DC 14V Power Connection Terminal

This product may be used with 90 ~ 264VAC.

(Voltage is automatically adjusted by the power adapter.)

2. PC connection terminal

z Computer connection terminal (DVI(HDCP))

z Computer connection terminal(15 Pin D-SUB)

3. AUDIO terminal

Audio connection terminal

4. COMPONENT terminal

z DVD/DTV left / right audio connection terminal (R/L)

z DVD/DTV Component(P

R

, P

B

,Y) terminal

5. FM RADIO / TV connection terminal

z FM RADIO ANT connection terminal

z TV connection terminal

For more information > Connecting TV

6. EXT(RGB) connection terminal

EXT(RGB) connection terminal

- Scart is mainly used in Europe.

7. AV connection terminal

z S-Video connection terminal (Input)

z Video connection terminal (Input)

z Left(L) / Right(R) audio connection terminal (Input)

z Headphone connection terminal (Output)

See Connecting the Monitor for further information regarding cable connections.

1. POWER

2. CHANNEL

3. +100, -/--

4. - +

5. MUTE

6. TTX/MIX

7. MENU

8. ENTER

9. FM RADIO

10. CH/P

11. SOURCE

12. INFO

Remote Control

The performance of the remote control may be affected by a TV or other electronic devices

operated near the monitor, causing malfuction due to interference with frequency.

13. EXIT

14. Up-Down Left-Right Buttons

15. AUTO

16. P.MODE, M/B (MagicBright™)

17. P.SIZE

18. STILL

19. PIP

20. S.MODE

21. DUAL/MTS

22. PRE-CH

23. SOURCE

24. SIZE

25. POSITION

26. MAGIC-CH

1. POWER

Use this button to turn the monitor on and off.

2. CHANNEL

Selects TV channels in the TV mode. You may use this button in PIP mode as well.

3. +100

Press to select channels over 100.

For example, to select channel 121, press "+100", then press "2" and "1".

-/-- (One/Two-Digit channel selection )

Use to select a channel numbered ten or over.

Press this button, and the "--" symbol is displayed.

Enter the two-digit channel number.

4. - +

Adjusts the audio volume.

5. MUTE

Pauses (mutes) the audio output temporarily.

Displays on the lower left corner of the screen.

The audio resumes if Mute or - + is pressed in the Mute mode.

6. TTX/MIX

TV channels provide written information services via teletext.

For more information > TTX / MIX

TTX / MIX is mainly used in Europe.

7. MENU

Use this button to open the on-screen menu and exit from the menu screen or close screen

adjustment menu.

8. ENTER

Activates a highlighted menu item.

9. FM RADIO

In areas where signal is weak, noise may occur while FM radio is broadcast.

10. CH/P

In TV mode, selects TV channels.

11. SOURCE

Switches from PC mode to Video mode.

Changing the source is allowed only external devices that are connected to the monitor at

the time.

12. INFO

Current picture information displays on the upper left corner of the screen.

13. EXIT

Exits from the menu screen.

14. Up-Down Left-Right Buttons

Moves from one menu item to another horizontally, vertically or adjusts selected menu

values.

15. AUTO

Adjusts the screen display automatically.

16. P.MODE, M/B (MagicBright™)

When you press this button, current mode is displayed on the lower center of the screen.

TV / AV / Ext. / S-Video /Component Mode : P.MODE( Picture Mode )

The Monitor has four automatic picture settings that are preset at the factory.

Then push button again to circle through available preconfigured modes.

( Dynamic Standard Movie Custom )

PC / DVI Mode : M/B ( MagicBright™ )

MagicBright™ is a new feature providing the optimum viewing environment depending on

the contents of the image you are watching.

Then push button again to circle through available preconfigured modes.

( Entertain Internet Text Custom )

17. P.SIZE - Not available in PC/DVI Mode

Press to change the screen size.

ZOOM1, ZOOM2 are not available in 1080i(or over 720p) of DTV.

18. STILL

Press the button once to freeze the screen. Press it again to unfreeze.

19. PIP

Push the PIP button to turn PIP screen On/Off.

20. S.MODE ( Sound Mode )

When you press this button, current mode is displayed on the lower center of the screen.

The Monitor has a built-in high fidelity stereo amplifier.

Then push button again to circle through available preconfigured modes.

( Standard Music Movie Speech Custom )

21. DUAL / MTS

DUAL : Use the DUAL button on the remote to select Stereo or Mono when the monitor is in

TV mode.

MTS : You can select the MTS (Multichannel Television Stereo) mode.

• Mono, Stereo, SAP (Separate Audio Program)

Set 'MTS' to ON to choose Mono, Stereo or SAP.

22. PRE-CH

This button is used to return to the immediately previous channel.

23. SOURCE

Selects the Video source.

24. SIZE

You can switch the Picture Size.

25. POSITION

Changing the Position of the PIP window.

26. MAGIC-CH

MagicChannel enables you to watch only certain channels.

This function is available only in Korea.

See Connecting the Monitor for further information regarding cable connections.

Connecting the monitor

1. Connecting to a Computer

1. Connect the power cord for your monitor to the power port on the back of the monitor.

Plug the power cord for the monitor into a nearby outlet.

2-1. Using the D-sub (Analog) connector on the video card.

Connect the signal cable to the 15-pin, D-sub connector on the back of your monitor.

2-2. Using the DVI (Digital) connector on the video card.

Connect the DVI Cable to the DVI Port on the back of your Monitor.

3. Connect the audio cable for your monitor to the audio port on the back of your computer.

4. Connect the power cord insert a plug in a wall outlet.

5. Turn on both your computer and the monitor.

6. You may enjoy clear and quality sound from the computer sound card using the monitor speakers.

(You don't need to install any separate speakers for your computer.)

You may get a blank screen depending on the type of video card you are using, if you connect

simultaneously both the D-sub and DVI cables to one computer.

If you connect properly your monitor using the DVI connector but get a blank or fuzzy screen, check

to see if the monitor status is set to analogue. Press Source button to have the monitor double-

check the input signal source.

2. Connecting to a Macintosh

1. Connect the power cord to the DC adapter and then connect the adapter jack to the DC POWER

port on the monitor. (Voltage is automatically adjusted by the power adapter.)

2. Using the D-sub (Analog) connector on the video card.

Connect the signal cable to the D-SUB port on the Macintosh computer.

3.

For older model Macintoshes, you need to adjust the resolution control DIP switch on the Macintosh

adapter (optional) referring to the switch configuration table shown on its rear.

4. Turn on the monitor and Macintosh.

Connecting to other devices

This monitor allows the user to connect it to such input devices as a DVD player, a VCR or a

camcorder, or a DTV or a TV without disconnecting the PC. For detailed information on connecting

AV input devices, refer to User Controls under Adjusting Your Monitor.

The configuration at the back of the monitor may vary from product to product.

1-1. Connecting AV Devices

The monitor has AV connection terminals to connect AV input devices like DVDs, VCRs or

Camcorders. You may enjoy AV signals as long as the monitor is turned on.

1. Input devices such as DVDs, VCRs or Camcorders are connected to the Video or S-Video terminal

of the monitor using the RCA or S-Video cable.

S-Video, RCA cable and SCRAT cable is optional.

2. Then, start the DVD, VCR or Camcorders with a DVD disc or tape inserted.

3. Select AV or S-Video using the SOURCE button on the monitor's front.

4. Connect the Audio (R) and Audio (L) terminals of a DVD, VCR or Camcorders to the monitor's R

and L audio input terminals using audio cables.

1-2. Connecting EXT.(RGB) - It only applies to AV DEVICE that supports SCART.

Connect to the DVD Devices input if the device has a DVD connector.You can watch DVD simply by

hooking up the DVD with the monitor as long as the power is on.

1. Connect a video cable between the EXT jacks on the Monitor and the EXT jacks on the DVD

Player.

2. Select Ext. by pressing SOURCE button on the monitor.

2. Connecting TV

You may view television programs on the monitor if it is connected to an antenna or a CATV cable

without installing any separate TV reception hardware or software on your computer.

1. Connect the CATV or antenna coaxial cable to the Antenna terminal on the rear of the monitor.

You need to use a coaxial antenna cable.

2. Turn on the monitor.

3. Select TV using Source button among the external signal adjustment buttons.

4. Select a desired TV channel.

When using an interior antenna terminal:

Check the antenna terminal on the wall first and connect the antenna cable.

When using an outdoor antenna:

If you are using an outdoor antenna, use a professional for installation if possible.

To connect the RF cable to the antenna input terminal:

Keep the copper wire portion of the RF cable straight.

Is weak signal causing poor reception?

Purchase and install a signal amplifier for better reception.

In areas where Antenna cable is not supported, first, attach Connecter to TV antenna .

3. Connecting DVD/DTV Set Top Box

Connect to the DVD/DTVSet Top Box input if the device has a DVD/DTV connector. You can watch

Component simply by hooking up the Component with the monitor as long as the power is on.

1. Connect the Audio (R) and Audio (L) outputs on the DVD / DTV set top box to the Audio (R) and

Audio (L) inputs on the monitor using audio cables.

2. Connect a video cable between the component( P

R

, P

B

,Y) jacks on the Monitor and the P

R

, P

B

,Y

jacks on the DVD / DTV set top box.

Page is loading ...

Samsung 930MP User manual

This manual is also suitable for

Samsung 930MP User manual

Related papers

Other documents