WAGO 750-459 User manual

Brand: WAGO

Model: 750-459

Type: User manual

Pos: 2 /Dokumentation al lgemein/Einband/Ei nband Handbuch - Frontsei te 2015 - mit DocVariab len (Standard) @ 9\mod_1285 229289866_0.docx @ 64941 @ @ 1

WAGO-I/O-SYSTEM 750

Manual

750-459

4AI 10V DC S.E.

4-Channel Analog Input Module 0-

10 V DC,

Single-

ended

Version 1.1.0

Pos: 3 /Alle Serien (Allge meine Module)/Hinwei se zur Dokumentation/I mpressum für Standardha ndbücher - allg. Angabe n, Anschriften, Telefonnummern und E-Mai l-Adressen @ 3\mod_1219151118203_21. docx @ 21060 @ @ 1

2 WAGO-I/O-SYSTEM 750

750-459 4AI 10V DC S.E.

Manual

Version 1.1.0

WAGO Kontakttechnik GmbH & Co. KG

Hansastraße 27

D-32423 Minden

Phone: +49 (0) 571/8 87 – 0

Fax: +49 (0) 571/8 87 – 1 69

E-Mail: [email protected]

Web: http://www.wago.com

Technical Support

Phone: +49 (0) 571/8 87 – 5 55

Fax: +49 (0) 571/8 87 – 85 55

E-Mail: [email protected]

Every conceivable measure has been taken to ensure the accuracy and

completeness of this documentation. However, as errors can never be fully

excluded, we always appreciate any information or suggestions for improving the

documentation.

E-Mail: [email protected]

We wish to point out that the software and hardware terms as well as the

trademarks of companies used and/or mentioned in the present manual are

generally protected by trademark or patent.

=== Ende der Liste für Te xtmarke Einband_vorne ===

WAGO-I/O-SYSTEM 750 Table of Contents 3

750-459 4AI 10V DC S.E.

Manual

Version 1.1.0

Pos: 5 /Dokumentation al lgemein/Verzeic hnisse/Inhaltsverzei chnis - Überschrif t oG und Verzeichnis @ 3\mod_1219 151230875_21.docx @ 21063 @ @ 1

Table of Contents

1 Notes about this Documentation ................................................................. 5

1.1 Validity of this Documentation ................................................................. 5

1.2 Copyright ................................................................................................... 5

1.3 Symbols ..................................................................................................... 6

1.4 Number Notation ....................................................................................... 8

1.5 Font Conventions ...................................................................................... 8

2 Important Notes ........................................................................................... 9

2.1 Legal Bases ............................................................................................... 9

2.1.1 Subject to Changes ............................................................................... 9

2.1.2 Personnel Qualifications ....................................................................... 9

2.1.3 Use of the WAGO-I/O-SYSTEM 750 in

Compliance with Underlying Provisions .............................................. 9

2.1.4 Technical Condition of Specified Devices ......................................... 10

2.2 Safety Advice (Precautions) .................................................................... 11

3 Device Description ..................................................................................... 13

3.1 View ........................................................................................................ 15

3.2 Connectors ............................................................................................... 16

3.2.1 Data Contacts/Internal Bus ................................................................. 16

3.2.2 Power Jumper Contacts/Field Supply ................................................ 17

3.2.3 CAGE CLAMP

Connectors ............................................................. 19

3.3 Display Elements .................................................................................... 20

3.4 Operating Elements ................................................................................. 20

3.5 Schematic Diagram ................................................................................. 21

3.6 Technical Data ........................................................................................ 22

3.6.1 Device ................................................................................................. 22

3.6.2 Supply ................................................................................................. 22

3.6.3 Communication .................................................................................. 22

3.6.4 Inputs .................................................................................................. 22

3.6.5 Climatic Environmental Conditions ................................................... 23

3.6.6 Connection Type ................................................................................ 23

3.7 Approvals ................................................................................................ 24

3.8 Standards and Guidelines ........................................................................ 26

4 Process Image ............................................................................................. 27

5 Mounting ..................................................................................................... 28

5.1 Mounting Sequence ................................................................................. 28

5.2 Inserting and Removing Devices ............................................................ 29

5.2.1 Inserting the I/O Module .................................................................... 29

5.2.2 Removing the I/O Module .................................................................. 30

6 Connect Devices ......................................................................................... 31

6.1 Connecting a Conductor to the CAGE CLAMP

................................... 31

6.2 Connection Example ............................................................................... 32

7 Use in Hazardous Environments .............................................................. 33

7.1 Marking Configuration Examples ........................................................... 34

7.1.1 Marking for Europe According to ATEX and IEC-Ex ...................... 34

4 Table of Contents WAGO-I/O-SYSTEM 750

750-459 4AI 10V DC S.E.

Manual

Version 1.1.0

7.1.2 Marking for America According to NEC 500 .................................... 39

7.2 Installation Regulations ........................................................................... 40

7.2.1 Special Conditions for Safe Use

(ATEX Certificate TÜV 07 ATEX 554086 X) .................................. 41

7.2.2 Special Conditions for Safe Use

(ATEX Certificate TÜV 12 ATEX 106032 X) .................................. 42

7.2.3 Special Conditions for Safe Use

(IEC-Ex Certificate TUN 09.0001 X) ................................................ 43

7.2.4 Special Conditions for Safe Use

(IEC-Ex Certificate IECEx TUN 12.0039 X) .................................... 44

7.2.5 Special Conditions for Safe Use According to ANSI/ISA 12.12.01 .. 45

List of Figures ...................................................................................................... 46

List of Tables ........................................................................................................ 47

=== Ende der Liste für Te xtmarke Verzeichnis_vorne = ==

WAGO-I/O-SYSTEM 750 Notes about this Documentation 5

750-459 4AI 10V DC S.E.

Manual

Version 1.1.0

Pos: 7 /Alle Serien (Al lgemeine Module)/Über schriften für alle Ser ien/Hinweise zur Doku mentation/Hinweise zu di eser Dokumentation - Überschrif t 1 @ 4\mod_1237987661750_21.doc x @ 29029 @ 1 @ 1

1 Notes about this Documentation

Pos: 8 /Alle Serien (Allge meine Module)/Hinw eise zur Dokumentation/ Hinweise/Hinwei s: Dokumentation aufbe wahren @ 4\mod_1237987 339812_21.docx @ 29026 @ @ 1

Always retain this documentation!

This documentation is part of the product. Therefore, retain the documentation

during the entire service life of the product. Pass on the documentation to any

subsequent user. In addition, ensure that any supplement to this documentation is

included, if necessary.

Pos: 9 /Alle Serien (Allge meine Module)/Übersc hriften für alle Seri en/Hinweise zur Dokument ation/Gültigkei tsbereich - Übersc hrift 2 @ 12\mod_1338912448776_ 21.docx @ 96469 @ 2 @ 1

1.1 Validity of this Documentation

Pos: 10 /Serie 750 (WA GO-I/O-SYSTEM)/Hinweise zur Dokumentati on/Gültigkeitsber eichGültigkeitsb ereich Dokumentatio n Busklemme 750-xxxx, nur Standardversion @ 14\mod_13 58944037400_21.doc x @ 109342 @ @ 1

This documentation is only applicable to the I/O module 750-459

(4AI 10V DC S.E.).

Pos: 11 /Serie 750 (WA GO-I/O-SYSTEM)/Hinweise zur Dokumentati on/Hinweise/Acht ung: Hinweis zur Dokument ation Busklemmen 750- xxxx @ 4\mod_1237986979656 _21.docx @ 29023 @ @ 1

The I/O module 750-459 shall only be installed and operated according to the

instructions in this manual and in the manual for the used fieldbus

coupler/controller.

Consider power layout of the WAGO-I/O-SYSTEM 750!

In addition to these operating instructions, you will also need the manual for the

used fieldbus coupler/controller, which can be downloaded at www.wago.com.

There, you can obtain important information including information on electrical

isolation, system power and supply specifications.

Pos: 12.1 /Alle Serien (Al lgemeine Module)/Hin weise zur Dokumentatio n/Urheberschutz ausf ührlich @ 4\mod_1235565 145234_21.doc x @ 27691 @ 2 @ 1

1.2 Copyright

This Manual, including all figures and illustrations, is copyright-protected. Any

further use of this Manual by third parties that violate pertinent copyright

provisions is prohibited. Reproduction, translation, electronic and phototechnical

filing/archiving (e.g., photocopying) as well as any amendments require the

written consent of WAGO Kontakttechnik GmbH & Co. KG, Minden, Germany.

Non-observance will involve the right to assert damage claims.

Pos: 12.2 /Dokumenta tion allgemein/Glied erungselemente/---Sei tenwechsel--- @ 3\mod_122110804 5078_0.docx @ 21810 @ @ 1

6 Notes about this Documentation WAGO-I/O-SYSTEM 750

750-459 4AI 10V DC S.E.

Manual

Version 1.1.0

Pos: 12.3 /Alle Serien (Al lgemeine Module)/Über schriften für alle Serien/Hinweise zur Dok umentation/Symbole - Überschrift 2 @ 13\ mod_1351068042408_21.doc x @ 105270 @ 2 @ 1

1.3 Symbols

Pos: 12.4.1 /Alle Serien ( Allgemeine Module)/ Wichtige Erläuterunge n/Sicherheits- und sonstige Hinweise/ Gefahr/Gefahr: _W arnung vor Personenschäden a llgemein_ - Erläuterung @ 13\ mod_1343309450020_ 21.docx @ 101029 @ @ 1

Personal Injury!

Indicates a high-risk, imminently hazardous situation which, if not avoided, will

result in death or serious injury.

Pos: 12.4.2 /Alle Serien ( Allgemeine Module)/ Wichtige Erläuterunge n/Sicherheits- und sonstige Hinweise/ Gefahr/Gefahr: _W arnung vor Personenschäden dur ch elektrischen Stro m_ - Erläuterung @ 13\mod_134 3309694914_21.doc x @ 101030 @ @ 1

Personal Injury Caused by Electric Current!

Indicates a high-risk, imminently hazardous situation which, if not avoided, will

result in death or serious injury.

Pos: 12.4.3 /Alle Serien ( Allgemeine Module)/ Wichtige Erläuterunge n/Sicherheits- und sonstige Hinweise/ Warnung/Warnung: _Warnung vor Personenschäd en allgemein_ - Erläuter ung @ 13\mod_134330987704 1_21.docx @ 101035 @ @ 1

Personal Injury!

Indicates a moderate-risk, potentially hazardous situation which, if not avoided,

could result in death or serious injury.

Pos: 12.4.4 /Alle Serien ( Allgemeine Module)/ Wichtige Erläuterunge n/Sicherheits- und sonstige Hinweise/ Vorsicht/Vorsi cht: _Warnung vor Personen schäden allgemein_ - Erläuterung @ 13\mod_1343310 028762_21.doc x @ 101038 @ @ 1

Personal Injury!

Indicates a low-risk, potentially hazardous situation which, if not avoided, may

result in minor or moderate injury.

Pos: 12.4.5 /Alle Serien ( Allgemeine Module)/ Wichtige Erläuterunge n/Sicherheits- und sonstige Hinweise/ Achtung/Achtung: _W arnung vor Sachschäden al lgemein_ - Erläuteru ng @ 13\mod_1343310134623 _21.docx @ 101041 @ @ 1

Damage to Property!

Indicates a potentially hazardous situation which, if not avoided, may result in

damage to property.

Pos: 12.4.6 /Alle Serien ( Allgemeine Module)/ Wichtige Erläuterunge n/Sicherheits- und sonstige Hinweise/ Achtung/Achtung: _W arnung vor Sachschäden dur ch elektrostatische Auf ladung_ - Erlä uterung @ 13\mod_1343 310227702_21.doc x @ 101044 @ @ 1

Damage to Property Caused by Electrostatic Discharge (ESD)!

Indicates a potentially hazardous situation which, if not avoided, may result in

damage to property.

Pos: 12.4.7 /Alle Serien ( Allgemeine Module)/ Wichtige Erläuterunge n/Sicherheits- und sonstige Hinweise/ Hinweis/Hinweis: _W ichtiger Hinweis al lgemein_ - Erläuterung @ 13\ mod_1343310326906_21. docx @ 101047 @ @ 1

Important Note!

Indicates a potential malfunction which, if not avoided, however, will not result in

damage to property.

Pos: 12.4.8 /Alle Serien ( Allgemeine Module)/ Wichtige Erläuterunge n/Sicherheits- und sonstige Hinweise/ Information/I nformation: _Wei tere Information allgemein_ - Erläuterung @ 13\mod_134 3310439814_21.doc x @ 101051 @ @ 1

WAGO-I/O-SYSTEM 750 Notes about this Documentation 7

750-459 4AI 10V DC S.E.

Manual

Version 1.1.0

Additional Information:

Refers to additional information which is not an integral part of this

documentation (e.g., the Internet).

Pos: 12.5 /Dokumenta tion allgemein/Glied erungselemente/---Sei tenwechsel--- @ 3\mod_122110804 5078_0.docx @ 21810 @ @ 1

8 Notes about this Documentation WAGO-I/O-SYSTEM 750

750-459 4AI 10V DC S.E.

Manual

Version 1.1.0

Pos: 12.6 /Alle Serien (Al lgemeine Module)/Hin weise zur Dokumentatio n/Darstellung der Zahlensysteme - Überschr ift 2 und Inhalt @ 3\mod_1221059 454015_21.doc x @ 21711 @ 2 @ 1

1.4 Number Notation

Table 1: Number Notation

Number Code

Example

Note

Decimal

100

Normal notation

Hexadecimal

0x64

C notation

Binary

'100'

'0110.0100'

In quotation marks, nibble separated with

dots (.)

Pos: 12.7 /Alle Serien (Al lgemeine Module)/Hin weise zur Dokumentatio n/Schriftkon ventionen - Überschri ft 2 und Inhalt @ 3\mod_122105952143 7_21.docx @ 21714 @ 2 @ 1

1.5 Font Conventions

Table 2: Font Conventions

Font Type

Indicates

italic

Names of paths and data files are marked in italic-type.

e.g.: C:\Program Files\WAGO Software

Menu items are marked in bold letters.

e.g.: Save

A greater-than sign between two names means the selection of a

menu item from a menu.

e.g.: File > New

Input

Designation of input or optional fields are marked in bold letters,

e.g.: Start of measurement range

“Value”

Input or selective values are marked in inverted commas.

e.g.: Enter the value “4 mA” under Start of measurement range.

[Button]

Pushbuttons in dialog boxes are marked with bold letters in square

brackets.

e.g.: [Input]

[Key]

Keys are marked with bold letters in square brackets.

e.g.: [F5]

Pos: 13 /Dokumentation al lgemein/Glieder ungselemente/---Seitenwec hsel--- @ 3\mod_122110804 5078_0.docx @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Important Notes 9

750-459 4AI 10V DC S.E.

Manual

Version 1.1.0

Pos: 14 /Alle Serien (A llgemeine Module)/Übersc hriften für alle Seri en/Wichtige Erläu terungen/Wichti ge Erläuterungen - Überschr ift 1 @ 4\mod_1241428899156_ 21.docx @ 32170 @ 1 @ 1

2 Important Notes

Pos: 15.1 /Alle Serien (Al lgemeine Dokumente) (Allgemeine Module)/W ichtige Erläuterunge n/Wichtige Erläuter ungen - Einleitung @ 3\mod _1221059818031_21.doc x @ 21717 @ @ 1

This section includes an overall summary of the most important safety

requirements and notes that are mentioned in each individual section. To protect

your health and prevent damage to devices as well, it is imperative to read and

carefully follow the safety guidelines.

Pos: 15.2 /Alle Serien (Al lgemeine Module)/Über schriften für alle Serien/Wichtige Er läuterungenRechtlic he Grundlagen - Übersc hrift 2 @ 3\mod_12210606263 43_21.docx @ 21726 @ 2 @ 1

2.1 Legal Bases

Pos: 15.3 /Alle Serien ( Allgemeine Dokumente) (Allgemeine Module)/ Wichtige Erläuterunge n/Änderungsvorb ehalt - Überschri ft 3 und Inhalt @ 3\mod_12210600364 84_21.docx @ 21720 @ 3 @ 1

2.1.1 Subject to Changes

WAGO Kontakttechnik GmbH & Co. KG reserves the right to provide for any

alterations or modifications that serve to increase the efficiency of technical

progress. WAGO Kontakttechnik GmbH & Co. KG owns all rights arising from

the granting of patents or from the legal protection of utility patents. Third-party

products are always mentioned without any reference to patent rights. Thus, the

existence of such rights cannot be excluded.

Pos: 15.4 /Serie 750 (W AGO-I/O-SYSTEM)/Wichtige Erläuterun gen/Personalquali fikationPersonal qualifikation 750- xxxx - Überschrif t 3 und Inhalt @ 3\mod_12240612080 46_21.docx @ 24063 @ 3 @ 1

2.1.2 Personnel Qualifications

All sequences implemented on WAGO-I/O-SYSTEM 750 devices may only be

carried out by electrical specialists with sufficient knowledge in automation. The

specialists must be familiar with the current norms and guidelines for the devices

and automated environments.

All changes to the coupler or controller should always be carried out by qualified

personnel with sufficient skills in PLC programming.

Pos: 15.5 /Serie 750 (W AGO-I/O-SYSTEM)/Wichtige Erläuterun gen/Bestimmungsge mäße VerwendungBesti mmungsgemäße Verwendun g 750-xxxx - Überschri ft 3 und Inhalt @ 3\mod_12240641512 34_21.docx @ 24070 @ 3 @ 1

2.1.3 Use of the WAGO-I/O-SYSTEM 750 in Compliance with

Underlying Provisions

Fieldbus couplers, fieldbus controllers and I/O modules found in the modular

WAGO-I/O-SYSTEM 750 receive digital and analog signals from sensors and

transmit them to actuators or higher-level control systems. Using programmable

controllers, the signals can also be (pre-) processed.

The devices have been developed for use in an environment that meets the IP20

protection class criteria. Protection against finger injury and solid impurities up to

12.5 mm diameter is assured; protection against water damage is not ensured.

Unless otherwise specified, operation of the devices in wet and dusty

environments is prohibited.

Operating the WAGO-I/O-SYSTEM 750 devices in home applications without

further measures is only permitted if they meet the emission limits (emissions of

interference) according to EN 61000-6-3. You will find the relevant information

in the section “Device Description” > “Standards and Guidelines” in the manual

for the used fieldbus coupler/controller.

10 Important Notes WAGO-I/O-SYSTEM 750

750-459 4AI 10V DC S.E.

Manual

Version 1.1.0

Appropriate housing (per 94/9/EG) is required when operating the WAGO-I/O-

SYSTEM 750 in hazardous environments. Please note that a prototype test

certificate must be obtained that confirms the correct installation of the system in

a housing or switch cabinet.

Pos: 15.6 /Alle Serien (Al lgemeine Dokumente) (Allgemeine Module)/W ichtige Erläuterunge n/Technischer Zusta nd der Geräte - Überschr ift 3 und Inhalt @ 3\mod_12210604 46109_21.docx @ 21723 @ 3 @ 1

2.1.4 Technical Condition of Specified Devices

The devices to be supplied ex works are equipped with hardware and software

configurations, which meet the individual application requirements. WAGO

Kontakttechnik GmbH & Co. KG will be exempted from any liability in case of

changes in hardware or software as well as to non-compliant usage of devices.

Please send your request for modified and new hardware or software

configurations directly to WAGO Kontakttechnik GmbH & Co. KG.

Pos: 15.7 /Dokumenta tion allgemein/Glied erungselemente/---Sei tenwechsel--- @ 3\mod_122110804 5078_0.docx @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Important Notes 11

750-459 4AI 10V DC S.E.

Manual

Version 1.1.0

Pos: 15.8 /Alle Serien (Al lgemeine Module)/Über schriften für alle Serien/Wichtige Er läuterungenSicherhei tshinweise - Überschr ift 2 @ 6\mod_1260180299987 _21.docx @ 46724 @ 2 @ 1

2.2 Safety Advice (Precautions)

Pos: 15.9 /Alle Serien (Al lgemeine Dokumente) (Allgemeine Module)/W ichtige Erläuterunge n/Sicherheitshin weise/Einleitung Si cherheitshinweis e Hardware @ 6\mod_1260 180170493_21.docx @ 46720 @ @ 1

For installing and operating purposes of the relevant device to your system the

following safety precautions shall be observed:

Pos: 15.10.1 /Alle Seri en (Allgemeine Dokumen te) (Allgemeine Module)/ Wichtige Erläuter ungen/Sicherhei tshinweise/Gefahr/ Gefahr: Nicht an Gerä ten unter Spannung arbei ten! @ 6\mod_1260180365327 _21.docx @ 46727 @ @ 1

Do not work on devices while energized!

All power sources to the device shall be switched off prior to performing any

installation, repair or maintenance work.

Pos: 15.10.2 /Seri e 750 (WAGO-I/O-SYSTEM)/Wichtige Erläut erungen/Sicherhei ts- und sonstige Hinweise/ Gefahr/Gefahr: Einbau 0750-xxxx nur i n Gehäusen, Schränken oder ele ktrischen Betriebsr äumen! @ 6\mod_1260180556 692_21.docx @ 46731 @ @ 1

Install the device only in appropriate housings, cabinets or in electrical

operation rooms!

The WAGO-I/O-SYSTEM 750 and its components are an open system. As such,

install the system and its components exclusively in appropriate housings,

cabinets or in electrical operation rooms. Allow access to such equipment and

fixtures to authorized, qualified staff only by means of specific keys or tools.

Pos: 15.10.3 /Alle Seri en (Allgemeine Dokumen te) (Allgemeine Module)/ Wichtige Erläuter ungen/Sicherhei tshinweise/Gefahr/ Gefahr: Unfallver hütungsvorschri ften beachten! @ 6\mod_1260 180657000_21.doc x @ 46735 @ @ 1

Pos: 15.10.4 /Alle Seri en (Allgemeine Dokumen te) (Allgemeine Module)/ Wichtige Erläuter ungen/Sicherhei tshinweise/Gefahr/ Gefahr: Auf normgerecht en Anschluss achten! @ 6\mod_1260180753479_ 21.docx @ 46739 @ @ 1

Pos: 15.11.1 /Alle Seri en (Allgemeine Dokumen te) (Allgemeine Module)/ Wichtige Erläu terungen/Sicherhei tshinweise/Achtun g/Achtung: Defekte od er beschädigte Geräte au stauschen! @ 6\mod_126018 0857358_21.doc x @ 46743 @ @ 1

Replace defective or damaged devices!

Replace defective or damaged device/module (e.g., in the event of deformed

contacts), since the long-term functionality of device/module involved can no

longer be ensured.

Pos: 15.11.2 /Alle Seri en (Allgemeine Dokumen te) (Allgemeine Module) /Wichtige Erläuter ungen/Sicherhei tshinweise/Achtun g/Achtung: Geräte vor kriechenden und isolier enden Stoffen schütze n! @ 6\mod_126018103621 6_21.docx @ 46747 @ @ 1

Protect the components against materials having seeping and insulating

properties!

The components are not resistant to materials having seeping and insulating

properties such as: aerosols, silicones and triglycerides (found in some hand

creams). If you cannot exclude that such materials will appear in the component

environment, then install the components in an enclosure being resistant to the

above-mentioned materials. Clean tools and materials are imperative for handling

devices/modules.

Pos: 15.11.3 /Alle Seri en (Allgemeine Dokumen te) (Allgemeine Module)/ Wichtige Erläuter ungen/Sicherhei tshinweise/Achtung/ Achtung: Reinigung nur mit zulässigen Materia lien! @ 6\mod_12601812 03293_21.docx @ 46751 @ @ 1

Clean only with permitted materials!

Clean soiled contacts using oil-free compressed air or with ethyl alcohol and

leather cloths.

Pos: 15.11.4 /Alle Seri en (Allgemeine Dokumen te) (Allgemeine Module)/ Wichtige Erläu terungen/Sicherhei tshinweise/Achtun g/Achtung: Kein Kontak tspray verwenden! @ 6\ mod_1260181290808_21. docx @ 46755 @ @ 1

12 Important Notes WAGO-I/O-SYSTEM 750

750-459 4AI 10V DC S.E.

Manual

Version 1.1.0

Do not use any contact spray!

Do not use any contact spray. The spray may impair contact area functionality in

connection with contamination.

Pos: 15.11.5 /Alle Seri en (Allgemeine Dokumen te) (Allgemeine Module)/ Wichtige Erläuter ungen/Sicherhei tshinweise/Achtung/ Achtung: Verpolung vermeiden! @ 6\mod_1260184 045744_21.doc x @ 46767 @ @ 1

Do not reverse the polarity of connection lines!

Avoid reverse polarity of data and power supply lines, as this may damage the

devices involved.

Pos: 15.11.6 /Alle Seri en (Allgemeine Dokumen te) (Allgemeine Module)/ Wichtige Erläuter ungen/Sicherhei tshinweise/Achtung/ Achtung: Elektrosta tische Entladung vermeid en! @ 6\mod_12601813647 29_21.docx @ 46759 @ @ 1

Avoid electrostatic discharge!

The devices are equipped with electronic components that may be destroyed by

electrostatic discharge when touched. Please observe the safety precautions

against electrostatic discharge per DIN EN 61340-5-1/-3. When handling the

devices, please ensure that environmental factors (personnel, work space and

packaging) are properly grounded.

Pos: 16 /Dokumentation allgemein/Glied erungselemente/---Sei tenwechsel--- @ 3\mod_122110804 5078_0.docx @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Device Description 13

750-459 4AI 10V DC S.E.

Manual

Version 1.1.0

Pos: 17 /Alle Serien (A llgemeine Module)/Übersc hriften für alle Seri en/Gerätebeschrei bung/Gerätebeschr eibung - Überschri ft 1 @ 3\mod_1233756084656_21.doc x @ 27096 @ 1 @ 1

3 Device Description

Pos: 18.1.1 /Seri e 750 (WAGO-I/O-SYSTEM)/Gerätebeschr eibung/Einleitung/ Anwendung/AI/Anwen dung 750-04xx AI SE (0... 10V) @ 5\mod_1246011969272_21. docx @ 36226 @ @ 1

The Analog Input Module 750-459 (4AI 10V DC S.E.) processes analog signals

with the norm value of 0 VDC ... 10 VDC.

Pos: 18.1.2 /Seri e 750 (WAGO-I/O-SYSTEM)/Gerätebeschr eibung/Einleitung/ I/O-Beschreibung/ AI/I/O-Beschrei bung 750-04xx 4 AI SE Felddsigna le über AI1 und Masse bzw. AI2/ 3/4 und Masse @ 5\mod_1246370 579270_21.doc x @ 36366 @ @ 1

The module has 4 input channels. The signals of the field side may be received via

the CAGE CLAMP

connectors AI 1 and common (ground) or AI 2, AI 3, AI 4

and common (ground) each.

The common (ground) contacts of all 4 channels have 1 common 0 V ground

potential.

Pos: 18.1.3 /Seri e 750 (WAGO-I/O-SYSTEM)/Gerätebeschr eibung/Einleitung/ Analogeingangskle mmen/Gerätebeschr eibung 750-0453; -0457, - 0459 Hinweis @ 16\mod_13793207848 28_21.docx @ 131624 @ @ 1

Common 0 V ground potential

This potential is not the 0 V field power of the blade contacts!

Pos: 18.1.4 /Seri e 750 (WAGO-I/O-SYSTEM)/Gerätebeschr eibung/Einleitung/ I/O-Beschreibung/ Allgemein/Verwei s auf Kapitel "Anschlüs se" @ 8\mod_1276775378035 _21.docx @ 57956 @ @ 1

The assignment of the connections is described in the “Connectors” section.

Pos: 18.1.5 /Seri e 750 (WAGO-I/O-SYSTEM)/Gerätebeschr eibung/Einleitung/ I/O-Beschreibung/ Allgemein/Verwei s auf Kapitel "Geräte ans chließen" > "Anschlussbei spiel(e)" @ 5\mod_1246 015203281_21.doc x @ 36298 @ @ 1

Connection examples are shown in section “Connecting Devices” > … >

“Connection Example(s)”.

Pos: 18.1.6 /Seri e 750 (WAGO-I/O-SYSTEM)/Gerätebeschreibung/ Einleitung/Funkti on/Galvanische Tre nnung Eingangssignal/ Systemebene (12 Bit) @ 6\mod_1255353269263_21. docx @ 42550 @ @ 1

The input signal is electrically isolated and is transmitted with a resolution of

12 bits.

Pos: 18.1.7 /Seri e 750 (WAGO-I/O-SYSTEM)/Gerätebeschrei bung/Einleitung/LE D-Anzeige/LED Fehler Bereichsüber-/unter schreitung @ 15\mod_13 70281145613_21.doc x @ 121530 @ @ 1

One red error LED per channel indicates when the measuring range is exceeded or

falls below for the respective channel.

Pos: 18.1.8 /Seri e 750 (WAGO-I/O-SYSTEM)/Gerätebeschr eibung/Einleitung/ LED-Anzeige/Verweis a uf Kapitel "Anzeigee lemente" @ 5\mod_1246010525 000_21.docx @ 36194 @ @ 1

The meaning of the LEDs is described in the “Display Elements” section.

Pos: 18.1.9 /Seri e 750 (WAGO-I/O-SYSTEM)/Gerätebeschr eibung/Einleitung/ Versorgung/Spannung sversorgung aus Syste mspannung @ 5\mod_1247116 433759_21.docx @ 36920 @ @ 1

Power to the internal electronics is supplied via internal data bus.

Pos: 18.1.10 /Seri e 750 (WAGO-I/O-SYSTEM)/Gerätebeschr eibung/Einleitung/ Versorgung/Versor gung 24 V, 0 V über Leistungsko ntakte _ Weitergabe ohne ei gene Verwendung @ 16\mod_13 79319855936_21.doc x @ 131620 @ @ 1

The I/O module receives the 24 V voltage supply and the 0 V potential for the

field level from an upstream I/O module or from the fieldbus coupler/controller

via the power jumper contacts used as blade contacts. These potentials are passed

through without being used galvanically isolated to subsequent I/O modules.

Pos: 18.1.11 /Seri e 750 (WAGO-I/O-SYSTEM)/Wichtige Erläut erungen/Sicherhei ts- und sonstige Hinweise/ Achtung/Achtung: Maximaler Strom Leistu ngskontakte 10 A @ 3\mod_1 226499143500_21.doc x @ 25029 @ @ 1

Do not exceed maximum current via power jumper contacts!

The maximum current to flow through the power jumper contacts is 10 A.

Greater currents can damage the contacts.

When configuring your system, ensure that this current is not exceeded. If

exceeded, insert an additional supply module.

Pos: 18.1.12 /Seri e 750 (WAGO-I/O-SYSTEM)/Wichtige Erläut erungen/Sicherhei ts- und sonstige Hinweise/ Hinweis/Hinweis: Potentialeinspei seklemme für Erde einset zen! (keine LK für Er de) @ 3\mod_1226499037468_21.doc x @ 25023 @ @ 1

14 Device Description WAGO-I/O-SYSTEM 750

750-459 4AI 10V DC S.E.

Manual

Version 1.1.0

Use supply modules for ground (earth)!

The I/O module has no power jumper contacts for receiving and transmitting the

earth potential. Use a supply module when an earth potential is needed for the

subsequent I/O modules.

Pos: 18.1.13 /Seri e 750 (WAGO-I/O-SYSTEM)/Gerätebeschr eibung/Einleitung/ Versorgung/Anordnu ng unter Berücksic htigung der Leistungskon takte beliebig @ 3\mod_123 3756233468_21.doc x @ 27099 @ @ 1

With consideration of the power jumper contacts, the individual modules can be

arranged in any combination when configuring the fieldbus node. An arrangement

in groups within the group of potentials is not necessary.

Pos: 18.1.14 /Seri e 750 (WAGO-I/O-SYSTEM)/Gerätebeschr eibung/Einleitung/ Einsatzbereic h/Einsatzbereich 750- xxxx alle Koppler/Con troller ohne Economy-Koppl er @ 3\mod_123254186746 8_21.docx @ 26525 @ @ 1

The I/O module 750-459 can be used with all fieldbus couplers/controllers of the

WAGO-I/O-SYSTEM 750 (except for the economy types 750-320, -323, -324

and -327).

Pos: 18.2 /Dokumenta tion allgemein/Glied erungselemente/---Sei tenwechsel--- @ 3\mod_1221108045078 _0.docx @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Device Description 15

750-459 4AI 10V DC S.E.

Manual

Version 1.1.0

Pos: 18.3 /Alle Serien (Al lgemeine Module)/Über schriften für alle Serien/Gerätebeschr eibung/Ansicht - Überschrift 2 @ 4\mod_12409 84217343_21.docx @ 31958 @ 2 @ 1

3.1 View

Pos: 18.4 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschreibung/Ansi cht/Analogeing angsklemmen/Ansicht 7 50-0459 @ 15\mod_137093387657 5_21.docx @ 122313 @ @ 1

Fig. 1: View

Pos: 18.5 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschrei bung/Ansicht/Ansic ht CageClamp®_Legende mit L EDs, mit 1 Entriegelung slasche @ 15\mod_137086718 8922_21.docx @ 122225 @ @ 1

Table 3: Legend for Figure “View”

Pos.

Description

Details See Section

Marking possibility with Mini-

WSB

---

Status LEDs

“Device Description” > “Display Elements”

Data contacts

“Device Description” > “Connectors”

CAGE CLAMP

connectors

“Device Description” > “Connectors”

Power jumper contacts

“Device Description” > “Connectors”

Release tab

“Mounting” > “Inserting and Removing

Devices”

Pos: 18.6 /Dokumenta tion allgemein/Glied erungselemente/---Sei tenwechsel--- @ 3\mod_12211 08045078_0.docx @ 21810 @ @ 1

16 Device Description WAGO-I/O-SYSTEM 750

750-459 4AI 10V DC S.E.

Manual

Version 1.1.0

Pos: 18.7 /Alle Serien (Al lgemeine Module)/Über schriften für alle Serien/Gerätebeschr eibung/Anschlüsse - Überschrift 2 @ 4\mod_124 0984262656_21.doc x @ 31961 @ 2 @ 1

3.2 Connectors

Pos: 18.8 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschrei bung/Anschlüsse/Dat enkontakte/Kle mmenbus - Überschrif t 3 @ 6\mod_1256294684083_21.doc x @ 43660 @ 3 @ 1

3.2.1 Data Contacts/Internal Bus

Pos: 18.9.1 /Seri e 750 (WAGO-I/O-SYSTEM)/Gerätebeschr eibung/Anschlüsse/ Datenkontakte - Feldb uskoppler/-c ontroller, Abbildung und Beschreibung @ 3\mod_123177 1259187_21.doc x @ 26002 @ @ 1

Communication between the fieldbus coupler/controller and the I/O modules as

well as the system supply of the I/O modules is carried out via the internal bus. It

is comprised of 6 data contacts, which are available as self-cleaning gold spring

contacts.

Figure 2: Data Contacts

Pos: 18.9.2 /Seri e 750 (WAGO-I/O-SYSTEM)/Wichtige Erläuter ungen/Sicherhei ts- und sonstige Hinweise/ Achtung/Achtung: Busklemmen nicht auf Go ldfederkontakte legen! @ 7\mod_1266318463636_ 21.docx @ 50695 @ @ 1

Do not place the I/O modules on the gold spring contacts!

Do not place the I/O modules on the gold spring contacts in order to avoid soiling

or scratching!

Pos: 18.9.3 /Seri e 750 (WAGO-I/O-SYSTEM)/Wichtige Erläuter ungen/Sicherhei ts- und sonstige Hinweise/ Achtung/Achtung: ESD - Auf gute Erdung der Umgebun g achten! @ 7\mod_1266318 538667_21.docx @ 50708 @ @ 1

Ensure that the environment is well grounded!

The devices are equipped with electronic components that may be destroyed by

electrostatic discharge. When handling the devices, ensure that the environment

(persons, workplace and packing) is well grounded. Avoid touching conductive

components, e.g. data contacts.

Pos: 18.10 /Dokumenta tion allgemein/Glie derungselemente/---Sei tenwechsel--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Device Description 17

750-459 4AI 10V DC S.E.

Manual

Version 1.1.0

Pos: 18.11 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschrei bung/Anschlüsse/Lei stungskontakte/ Feldversorgung - Überschrift 3 @ 6\mod_12562946 92864_21.docx @ 43664 @ 3 @ 1

3.2.2 Power Jumper Contacts/Field Supply

Pos: 18.12.1 /Seri e 750 (WAGO-I/O-SYSTEM)/Wichtige Erläut erungen/Sicherhei ts- und sonstige Hinweise/ Vorsicht/Vorsic ht: Verletzungsg efahr durch scharf kantige Messerkontakte! @ 6\ mod_1256193279401_ 21.docx @ 43414 @ @ 1

Risk of injury due to sharp-edged blade contacts!

The blade contacts are sharp-edged. Handle the I/O module carefully to prevent

injury.

Pos: 18.12.2 /Seri e 750 (WAGO-I/O-SYSTEM)/Gerätebeschr eibung/Anschlüsse/Lei stungskontakte 2 LK ( Messer/Leistungsko ntakte 2 LK (Messer/Feder ) - Einleitung @ 15\mod_ 1371721641099_21.doc x @ 123714 @ @ 1

The I/O module 750-459 has 2 self-cleaning power jumper contacts that supply

and transmit power for the field side. The contacts on the left side of the I/O

module are designed as blade contacts and those on the right side as spring

contacts.

Pos: 18.12.3 /Seri e 750 (WAGO-I/O-SYSTEM)/Gerätebeschr eibung/Anschlüsse/Lei stungskontakte 2 LK ( Messer/Leistungsko ntakte 2 LK (Messer/Feder ) - Abbildung, einfac he Breite - Standard @ 15\mod_1 367500700037_21. docx @ 118396 @ @ 1

Figure 3: Power Jumper Contacts

Pos: 18.12.4 /Seri e 750 (WAGO-I/O-SYSTEM)/Gerätebeschr eibung/Anschlüsse/Lei stungskontakte 2 LK ( Messer/Leistungsko ntakte 2 LK (Messer/Feder ) - Legende @ 15\mod_13717 21352500_21.docx @ 123710 @ @ 1

Table 4: Legend for Figure “Power Jumper Contacts”

Contact

Type

Function

Spring contact

Potential transmission (U

) for field supply

Spring contact

Potential transmission (0 V) for field supply

Blade contact

Potential feed-in (0 V) for field supply

Blade contact

Potential feed-in (U

) for field supply

Pos: 18.12.5 /Seri e 750 (WAGO-I/O-SYSTEM)/Wichtige Erläut erungen/Sicherhei ts- und sonstige Hinweise/ Achtung/Achtung: Maximaler Strom Leistu ngskontakte 10 A @ 3\mod_1 226499143500_21.doc x @ 25029 @ @ 1

Do not exceed maximum current via power jumper contacts!

The maximum current to flow through the power jumper contacts is 10 A.

Greater currents can damage the contacts.

When configuring your system, ensure that this current is not exceeded. If

exceeded, insert an additional supply module.

Pos: 18.12.6 /Seri e 750 (WAGO-I/O-SYSTEM)/Wichtige Erläut erungen/Sicherhei ts- und sonstige Hinweise/ Hinweis/Hinweis: Potentialeinspei seklemme für Erde einset zen! (keine LK für Er de) @ 3\mod_1226499037468_21.doc x @ 25023 @ @ 1

18 Device Description WAGO-I/O-SYSTEM 750

750-459 4AI 10V DC S.E.

Manual

Version 1.1.0

Use supply modules for ground (earth)!

The I/O module has no power jumper contacts for receiving and transmitting the

earth potential. Use a supply module when an earth potential is needed for the

subsequent I/O modules.

Pos: 18.13 /Dokumenta tion allgemein/Glie derungselemente/---Sei tenwechsel--- @ 3\mod_1221108045078_0. docx @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Device Description 19

750-459 4AI 10V DC S.E.

Manual

Version 1.1.0

Pos: 18.14 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschrei bung/Anschlüsse/CA GE CLAMP-Anschlüsse - Übersc hrift 3 @ 6\mod_1256296337 770_21.docx @ 43674 @ 3 @ 1

3.2.3 CAGE CLAMP

Connectors

Pos: 18.15 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschrei bung/Anschlüsse/Ana logeingangskle mmen/Anschlüsse 750-04 53, -0455, -0457 und -0459 @ 15\mod_ 1370335893038_21. docx @ 121647 @ @ 1

Figure 4: CAGE CLAMP

Connectors

Table 5: Legend for Figure “CAGE CLAMP

Connectors”

Channel

Designation

Connector

Function

AI 1

Analog input1: Signal

Common

(ground)

2 Analog input: Common (ground)

AI 2

Analog input 2: Signal

Common

(ground)

6 Analog input: Common (ground)

AI 3

Analog input 3: Signal

Common

(ground)

4 Analog input: Common (ground)

AI 4

Analog input 4: Signal

Common

(ground)

8 Analog input: Common (ground)

Pos: 18.16 /Serie 750 (W AGO-I/O-SYSTEM)/Wichtige Erläuter ungen/Sicherhei ts- und sonstige Hinweise/ Hinweis/Hinweis: Geschirmte Signallei tungen verwenden! @ 7\ mod_1265723251019_21. docx @ 50140 @ @ 1

Use shielded signal lines!

Only use shielded signal lines for analog signals and I/O modules which are

equipped with shield clamps. Only then can you ensure that the accuracy and

interference immunity specified for the respective I/O module can be achieved

even in the presence of interference acting on the signal cable.

Pos: 18.17 /Dokumenta tion allgemein/Glie derungselemente/---Sei tenwechsel--- @ 3\mod_1221108045078_0. docx @ 21810 @ @ 1

20 Device Description WAGO-I/O-SYSTEM 750

750-459 4AI 10V DC S.E.

Manual

Version 1.1.0

Pos: 18.18 /Alle Serien ( Allgemeine Module)/ Überschriften für alle Serien/Gerätebesc hreibung/Anzeigee lemente - Überschri ft 2 @ 4\mod_1240984390875_21.doc x @ 31964 @ 2 @ 1

3.3 Display Elements

Pos: 18.19 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschrei bung/Anzeigeelement e/Analogeingangsk lemmen/Anzeigeelem ente 750-0457, -0459 @ 15\mod_1370335605129_21.doc x @ 121643 @ @ 1

Figure 5: Display Elements

Table 6: Legend for Figure “Display Elements”

Channel

Designation

LED

State

Function

1 Error AI 1 A

Off

Normal operation

Red

Excess/underflow

of the admissible measuring range

2 Error AI 2 C

Off

Normal operation

Red

Excess/underflow

of the admissible measuring range

3 Error AI 3 B

Off

Normal operation

Red

Excess/underflow

of the admissible measuring range

4 Error AI 4 D

Off

Normal operation

Red

Excess/underflow

of the admissible measuring range

Pos: 18.20 /Alle Serien ( Allgemeine Module)/ Überschriften für alle Serien/Gerätebesc hreibung/Bedienel emente - Überschrif t 2 @ 4\mod_1239191655456_21.doc x @ 30439 @ 2 @ 1

3.4 Operating Elements

Pos: 18.21 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschreibung/Be dienelemente/Bedi enelemente Busklem me 750-xxxx nicht vorhande n @ 4\mod_1236322031125_21. docx @ 28063 @ @ 1

The I/O module 750-459 has no operating elements.

Pos: 18.22 /Dokumenta tion allgemein/Glie derungselemente/---S eitenwechsel--- @ 3\mod_122110804507 8_0.docx @ 21810 @ @ 1

Page is loading ...

WAGO 750-459 User manual

WAGO 750-459 User manual

Related papers

Other documents