VIORE PD50VH80 Operating Instructions Manual

VIORE TM

T EC H N O LO G Y & INNOVATION

50" Plasma Television

PD5OVH80

AIR (TV)/CABLE MODE SELECTION

The Air/Cable menu option is set to the "CABLE" (Cable Television) mode at the factory.

If you want to use an antenna for the built - in TV tuner, this menu option must be set to the

"Air" mode. Please refer to"CHANNEL MENU"in page 19 of this manual for the details.

Important Precautions

OUTDOOR USER MARKING

WARNING: To reduce the risk of fire or electric shock hazard, do not expose this appliance to rain or

moisture.

WET LOCATION MARKING

"Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be

placed on the apparatus."

Service Instructions

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION • TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended

to alert the user to the presence of uninsulated "dangerous voltage" with-in the

product's enclosure that may be of sufficient magnitude to constitute a risk electric

shock.

The exclamation point within an equilateral triangle is intended to alert the user to

the presence of important operating and servicing instructions in the literature

accompanying the appliance.

GB-1

Please carefully study this manual and always keep it available. The following are some installation

and operation precautions, which you should be aware as a matter of safety,

Important Safety Instructions

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Followed instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.

8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus

(including amplifiers) that produce heat.

9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades

with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide

blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet,

consult an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles,

and the point where they exit from the apparatus.

11) Only use attachments/accessories specified by the manufacturer.

12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, ors old with the

apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury

from tip-over.

13) Unplug this apparatus during lightning storms or when unused for long periods of time.

14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects

have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate

normally, or has been dropped.

Warning

1) To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.

2) The apparatus shall not be expose d to dripping or splashing and that no objects filled with liquids, such as

vases, shall be placed on the apparatus.

3) The disconnect device (appliance power connecter) shall remain readily operable.

4) Changes or modifications to this unit not expressly approved by the party responsible for compliance

could void the user's authority to operate the equipment.

CAUTION:

This product satisfies FCC regulations when shielded cables and connectors are used to connect the unit to

other equipment. To prevent electromagnetic interference with electric appliances such as radios and

televisions, use shielded cables and connectors for connections.

DECLARATION:

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired

operation.

GB-2

INFORMATION:

ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassBdigitaldevice,pursuantto

Part 15 of the FCCRules.Theselimitsare designedto providereasonableprotectionagainstharmful

interferenceina residentialinstallation.Thisequipmentgenerates,usesandcanradiateradiofrequency

energyand,ifnotinstalledandusedinaccordancewiththeinstructions,maycauseharmfulinterferenceto

radiocommunications.However,there is no guaranteethat interferencewill not occurin a particular

installation.Ifthisequipmentdoescauseharmfulinterferencetoradioortelevisionreception,whichcanbe

determinedbyturningtheequipmentoffandon,theuserisencouragedtotryto correcttheinterferenceby

oneormoreofthefollowingmeasures:

Reorientorrelocatethereceivingantenna.

Increasetheseparationbetweentheequipmentandreceiver.

Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhichthereceiverisconnected.

Consultthedealeroranexperiencedradio/TVtechnicianfor help.

Notes:

Wide screen format PDP Displays (16:9, the aspect ratio of the screen width to height) are primarily

designed to view wide screen format full-motion video. The images displayed on them should primarily be in

the wide screen 16:9 ratio format, or expanded to fill the screen if your model offers this feature and the

images are constantly moving. Displaying stationary graphics and images on screen, such as the dark

side-bars on no expanded standard format television video and programming, should be limited to no more

than 5% of the total television viewing per week.

Additionally, viewing other stationary images and text such as stock market reports, video game displays,

station Iogos, web sites or computer graphics and patterns, should be limited as described above.

Displaying stationary images that exceed the above guidelines can cause uneven aging of PDP Displays

that leave subtle, but permanent burned-in ghost images in the PDP picture. To avoid this, vary the

programming and images, and primarily display full screen moving images, not stationary patterns or dark

bars. Be careful in the selection and duration of television formats used for viewing. Uneven PDP aging as a

result of format selection and use, as well as burned-in images, are not covered by the warranty.

GB-3

CONTENTS

Safety Precautions

• Important Precautions ....................................................................................................................... 1

User Guidance Information

• Names of each part (Front View)/Accessories .................................................................................. 5

• Names of each part (Back View) ....................................................................................................... 6

• Wall Mount ........................................................................................................................................ 7

• Remote control .................................................................................................................................. 8

• Precautions/How to use remote control ............................................................................................ 9

Basic Use

• Powering the TV/Selecting input source ......................................................................................... 10

Application

• Operating the Menu ........................................................................................................................ 11

• Customizing the PICTURE Settings .............................................................................................. 12

• Customizing the SOUND Settings ................................................................................................. 13

• Customizing the TIMER Settings ................................................................................................... 14

• Customizing the SETUP Settings .............................................................................................. 15~16

• Customizing the LOCK Settings ................................................................................................ 17~19

• Customizing the CHANNEL Settings ....................................................................................... 20~21

Maintenance and Service

• Troubleshooting ............................................................................................................................. 22

GB-4

User Guidance Information

Names of each part (FrontView)

i

• @ 0 0 0

V_L- VOL+ CH- CH÷ _NPUT MENU POWER

O VOL+/- button - Volume +.- Button

CH+/- button - Channel/Program +.- Button

INPUT button - Input Source Select Button

O MENU button - OSD Menu Display Button

i_ POWER button

(_ Remote Control Window

O LED ndicator

Accessories

' The configuration of the components may look different from the following illustration.

User's Manual

Batteries for Remote Control

(Size AAAx2 PCS)

User's Guide Power Cord Remote Control

GB-5

User Guidance Information

Names of each part

AC _- S_V_C_ H;D_t3 HDM2 IHDM1

Pb

SPOF RF

Pr L R S-VIOEO I AMY _put

1. AC ~ : Connect to an earth 100-240V, 50/60Hz AC outlet with the power cable.

2. SERVICE: USB Slot. (only for service )

3. HDMII/2/3: Connect them to the HDMI-devices with HDMI output sockets. (used in HDMI1/HDMI2/HDMI3

mode)

4. VGA: For PC display. Connect it to the D-Sub 15 pins analog output connector of the PC.

5. PC AUDIO IN: Connect it to the audio output terminal of PC.

6. VIDEO: Connect it to video output terminal of DVD.(used in AV2<CVBS> mode)

L/R in : Connect them to the audio output terminal of DVD.(with AV2 and YPbPr)

7.YPbPr: Connect them to the video output terminal of DVD.(used in YPbPr mode).

8. VIDEO: Video output.

L/R out : Audio output.

9. VIDEO: Connect it to video output terminal of DVD.(used in AVl<CVBS> mode)

L/R in : Connect them to the audio output terminal of DVD.(with AV1 and S-VIDEO)

10.SPDIF : SPDIF output.

11. S-VIDEO: Connect them to the AV devices with S-VIDEO output sockets. (used in AVI<S-VIDEO> mode)

12. RF: Connect antenna or cable 75 Ohm coaxial to receive TV signal.

* S-VIDEO and AVl share an audio.

* AV2 and YPbPr share an audio.

GB-6

User Guidance Information

Wall Mount

The wall mount kit (not included) with your purchase allows you to mount your VIORE TV on the wall.

For detailed information on installing the wall mount, refer to the instructions provided by the wall

mount manufacturer. It is strongly recommended to contact a technician for professional assistance

for wall mount installation. VlORE is not responsible for any damage to the product or injury to

yourself or others resulting from the wall-mounting.

VESA Dimensions for Wall Mount

°i!ill!illiii!ill-°121!i!iili!i!i° !!!i!iii!ii oi!!i!I!i!°

This TV is compliant with the VESA Standard mounting hole pattern 500mm x 400mm.

4 pcs of type M7 screws are required for installing the wall mount bracket to your VlORE TV.

Do not use screws that are longer than 14 mm. Screws that are too long may cause damage to the inside

of the TV set.

Do not fasten the screws too tight for this may damage the TV or cause the TV to fall, resulting in

Personal injury. VIORE is not liable for these kinds of incidents.

Do not mount the TV at more than a 15 degree tilt.

Always use two people to mount the TV to a wall.

Do not install your Wall Mount Kit while your TV is turned on. It may result

in personal injury due to electric shock.

GB-7

User Guidance Information

Remote Control

• Functions of remote control buttons

The remote control is using Infra-Red (IR). Point it towards the front of the LCD TV. The remote control may not

work correctly if it is operated out of range or out of angle.

1. POWER

Press to turn the TV on/standby

2. NUMBER BUTTONS

To select the program directly. 1

e.g.:

Select channel 5, press "5" button.

Select channel 62 2

press "6" button, and press "2"

button in 2 seconds.

Select channel 152

press "1" button, and press "5"

button, then press "2" button

in 2 seconds, select channel "5-1",

press "5" then "-/--" and "1".

3. VOL+/-

Volume +/- 3

4. EXIT

Press to exit form the OSD menu.

5. THU MBSTICK( A /T/_1/1_/OK) 4

Allows you to navigate the

on-screen menus and adjust the

system settings to your

preference. 5

6. CC

Press to display the closed caption.

7. MTS

Press to select the audio channels. 8

8. PICTURE 9

Press repeatedly to cycle

through the available video

picture modes.

9. SOUND

Press to cycle through the

different sound settings.

10. CH.LIST

10 Used to display the channel list.

11. INPUT

11 Press to display the input source

menu.

12.

Press to Return to the previous

channel viewed.

13. MUTE

Press to mute the sound. Press

again or press VOL+ to unmute.

12 14. CH+/-

13 Channel/Program +/-

15. MENU

Press to display the OSD menu.

I4

16. FAV

Press to display the favorite

channels list.

!5 17. EPG

Press to enter the EPG menu

directly.

18. DISPLAY

Displays the program information.

19. SLEEP

16 Press to setup the sleep time

17 among: 5min, 10min, 15min, 30min,

I8 45min, 60min, 90min, 120min,

19 180min, 240min and off.

GB-8

User Guidance Information

Precautions

Avoiding Remote Control Problems

1. Check the polarity (+,-) of the batteries in the remote control.

2. Check that the batteries have power.

3. Check that the TV is powered and that it is properly plugged in.

4. Check if any three-wavelength lamp, special fluorescent or neon sign is turned on near the TV.

Inserting Batteries in the Remote Control

1. Open the cover completely.

2. Insert the two supplied batteries. Ensure that the polarities (+ and -) of the batteries are aligned correctly.

3. Slide back the cover.

CAUTION • Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries

according to the national code (Recycling program).

How to use remote control

The remote control should be operated within 30 feet (7m) and 30 ° to the left and the right of the IR

receiver at the front of the TV.

• Used batteries should be disposed properly.

GB-9

Basic Use

Powering the TV

• Power on/off

• To turn the TV on :

Press "POWER" button on the TV.

• To turn the TV off:

Press "POWER" button on the TV.

• To turn on/off by remote control:

Press the O button of remote control.

Selecting Input Source

• You can select between the TV signal and the input signal of other equipments connected to the TV.

• Use this function to switch to the input source you wish to view.

Press

INPUT

button on the remote control.

_iii i

Use to move to the desired input signal source.

Press

to select.

GB-IO

Application

Operating the Menu

1. After you turn on the TV and select the input source, you should setup the on-screen menu.

2. Press MENU button to display the on-screen menu.

3. Press 4/ D,button to select the main menu: PICTURE, AUDIO, TIME, SETUP, LOCK, CHANNEL.

4. Press • button to enter the main menu.

PICTURE MENU: AUDIO MENU:

Allows you to make adjustments to your picture Allows you to customize the sound options and effects

settings. (Select TV source for example)

(select TV source for example)

TIME MENU: SETUP MENU:

Allows you to set up a variety of timer options. Allows you to set up a variety of setup options.

(Select TV source) (Select TV source)

LOCK MENU: CHANNEL MENU:

Allows you to set up a variety of lock options. Allows you to search channels and set up a variety of channel

(Select TV source o3tions.

Select TV source)

5. Press •/A button to select the item in the main menu.

6. Press4/ D,button to adjust or select;

Press I_ button to enter the submenu.

7. Press EXIT button to exit the menu or press MENU button to go back to the previous menu.

Note:

1. Only when you input the suitable signal, the relevant items can be activated.

2. You should according to the hints on the bottom of menu.

GB-11

Application

Customizing the PICTURE Settings

The PICTURE menu includes the following options •

Picture Mode Cycles among picture display modes: Standard, Vivid, Factory, Mild, Customer.

Contrast Controls the difference between the brightest and darkest regions of the picture.

Brightness Controls the overall brightness of the picture.

Saturation Controls the saturation.

Tint Controls the tint (only could be operated in NTSC mode).

Sharpness Increase this setting to see crisp edges in the picture; decrease it for soft edges.

Color Temp Cycles among color modes: Cool, Normal, Warm.

GB-12

Application

Customizing the AUDIO Settings

The AUDIO menu includes the following options •

Audio Mode Allows you to select among: Standard, Music, Movie, Sports and Customer.

Bass Controls the relative intensity of lower pitched sounds.

Treble Controls the relative intensity of higher pitched sounds

Balance To adjust the balance of the left and right sound track, or turn off the volume of

the left and right sound track.

Surround To turn on or off the Surround function.

AVL To turn on or off the AVL function.

SPDIF Type Allows you to select between PCM and RAW.

Audio Language Allows you to select audio languages among.

GB-13

Application

Customizing the TIMER Settings

Sleep Allows you to set up the sleep among: 5min, 10min, 15min, 30min, 45min,

60min, 90min, 120min, 180min, 240min and off.

Time Zone Allows you to set up the sleep timer among: Pacific, Alaska, Hawaii, Eastern,

Central and Mountain.

Daylight Saving Time Allows you to turn on or off the daylight saving time.

Data / Time

User can not change time manually during DTV mode, for time is from signal

source directly.

GB-14

Application

Customizing the SETUP Settings

includes the following options:

The SETUP menu

Menu Language Allows you to select menu language among: English, Fran£ais and EspaSol.

Menu Opacity Allows you to turn on or off the menu opacity function.

Zoom Mode Allows you to select the zoom mode among: Normal, Wide, Zoom, and Cinema.

DNR Allows you to select the DNR among: Off, Minimum, Medium and Maximum.

PC Input PC signal first, then press INPUT button to select VGA mode, press OK

button to confirm.

H-Position

V-Position

Clock

Phase

Auto

Allow you to use _ and • button to adjust the H Position.

Allow you to use _ and • button to adjust the V Position.

Allow you to prolong the image.

Allow you to adjust the definition.

Select "Auto" and press • button, the unit will

automatically adjust all items to achieve a best effect.

GB-15

Application

Customizing the SETUP Settings

Closed Caption Use • button to highlight the Closed Caption item, then press • button to enter

into the following menu.

CC Mode

Basic Selection

Advanced Selection

Option

Allows you to select the CC Mode among: On, Off and CC

on Mute.

Allows you to select the basic selection among: Off, CC1,

CC2, CC3, CC4, Textl, Text2, Text3 and Text4.

Allows you to select the advanced selection among:

Service 1, Service 2, Serviced 3 Service 4, Service 5 and

Service 6.

Use • button to highlight the "Option" item, then press •

button to enter into the following menu.

Use • and • buttons to highlight the desired item, and

use .qand • buttons to select.

Advanced Use • button to highlight the Closed Caption item, then press • button to enter

into the following menu.

XVS Turn on/off the function to adjust the dynamic brightness

automatically.

Energy Saving Allows you to select the Energy Saving among: Off, Low,

Medium and High.

Restore Default Restores all settings in SETUP menu to factory settings.

GB-16

Application

Customizing the LOCK Settings

You should enter the password to enter the Lock menu. NOTE: the factory password is 0000.

input

4-digital password

The LOCK menu includes the following options •

Change Password UseT button to select the "Change Password" item, then press • button to

enter into the following menu.

Input the new 4-digital password and input it again to confirm.

System Lock Allows you to turn on or off the system lock.

If you turn off the system lock, then the following items (US, Canada, RRT

Setting and Reset RRT) will unable to use.

GB-17

Application

Customizing the LOCK Settings

US

Use • button to highlight the "US" item, then press • button to enter into the

following menu.

TV

Use • button to highlight the "TV" item, then press • button to

enter into the following menu.

Use • and • buttons to select the desired rating and press •

button to block or unblock rating.

MPAA

The Movie rating (MPAA) is used for original movies rated by

the Motion Picture Association of America (MPAA) as

broadcasted on cable TV and not edited for television.

Use UP or DOWN button to select N/A, G, PG, PG-13, R,

NC-17 or X.

RATING DESCRIPTION

G General Audiences. Movie is appropriate for all

ages.

PG Parental Guidance Suggested. May contain material

not suited for younger viewers.

PG-13 Contains content that may not be appropriate for

viewers under the age of 13.

R Restricted. Contains adult content, no one under 17

admitted without parent.

NC-17 No one 17 and under admitted.

X Adults only.

GB-18

Application

Customizing the LOCK Settings

Canada

Use Down button to highlight the "Canada" item, then press RIGHT button to enter

into the following menu.

Canada English Use LEFT and RIGHT buttons to select among: E, C, C8+, G,

PG, 14+ and 18+

Canada French

Use LEFT and RIGHT buttons to select among: E, G, 8ans+,

13ans+,16ans+ and 18ans+

RRT Setting Press • to select and enter the RRT setting menu.

Reset RRT Allows you to reset the RRT setting.

GB-19

Page is loading ...

VIORE PD50VH80 Operating Instructions Manual

This manual is also suitable for

VIORE PD50VH80 Operating Instructions Manual

in other languages

Related papers

Other documents