MODEL: 1320
3/8" Mini Buttery Impact Wrench
SPECIFICATIONS
Important Warnings - Impacts
1. Eye protection and hearing protection and safety gloves must always be worn when operating an impact wrench or impact
driver.
2. When using heavy impact sockets or sockets on impact wrenches with 3/4” drive anvils or larger, a socket retaining ring
and pin should be used to prevent the socket falling off and causing injury.
3. Use only impact sockets and accessories. Only use sockets designated “FOR USE WITH IMPACT WRENCHES”, hand tool
damage and replace when necessary.
Accessory Hazards
4. Disconnect the assembly power tool for threaded fasteners from the energy supply before changing the inserted tool or
accessory.
5. Do not touch sockets or accessories during impacting as this increases the risk of cuts, burns or vibration injuries.
6. Use only sizes and types of accessories and consumables that are recommended by the assembly power tool for threaded
fasteners manufacturer; do not use other types or sizes of accessories and consumables.
Tools of this class operate on a wide range of air pressure. It is recommended that air pressure of these tools measures 90 PSI at the tool while running free. Higher
pressure and unclean air will shorten the tool’s life because of faster wear and may create a hazardous condition and void the warranty. Water in the air line will
cause damage to the tool. Drain the air tank daily. Clean the air inlet lter screen on at least a weekly schedule. The recommended hookup procedure can be viewed
in the illustration below. The air inlet, used for connecting air supply, has standard 3/8” NPT American Thread or BSP British Standard Pipethread. Line pressure
should be increased to compensate for unusually long air hoses (over 25 feet). Minimum hose diameter should be 3/8 I.D. and ttings should have the same inside
dimensions.
Model No.
Free Speed
(RPM)
Bolt
Capacity
(in.)
Square
Drive
(in.)
Impacts Per
Minute
Max Torque
(ft-lb)
Weight
(lbs.)
Length
(in)
Air Cons.
(CFM)
Rec. Hose
Size
(in.)
Air Inlet
(in.)
1320 10,000 1/2 3/8 1800 80 1.1 5.4 8 3/8 1/4
MODEL: 1320
3/8" Mini Buttery Impact Wrench
Exploded View Drawing
1
3
4
6
7
8
10
11
23
24
25
9
34
33
30
35
36
37
38
26
27
28
18
15
14
13
22
20
19
17
16
12
21
32
31
5
29
39
40
Ref
#
Part Number Description Qty Ref
#
Part Number Description Qty.
1 9213001A-CAT MOTOR HOUSING &
BUSHING ASSEMBLY
1 21 9213021 HOUSING CAP 1
22 9213022-CAT THROTTLE LEVER 1
3 9213003 WASHER 1 23 9213023 VALVE STEM 2
4 9213004 ANVIL BUSHING 1 24 9213024 SPRING 2
5 9328830-3 SOCKET RETAINER 1 25 9213025 PIN 2
6 9328829-3 O-RING 1 26 9589055 O-RING 2
7 9213007-38 3/8" ANVIL 1 27 9213027 THROTTLE VALVE 2
8 9213008 HAMMER PIN 2 28 9213028 SPRING 2
9 9213009 HAMMER CAGE 1 29 9SPP0214 SPRING PIN 1
10 9213010 HAMMER 2 30 9213030 AIR INLET 1
11 9213011 CAM 1 31 9213033 BUSHING 1
12 9B608ZZ BALL BEARING 1 32 9213034 SCREW 1
13 9213013 FRONT END PLATE 1 33 9162030 SPRING WASHER 2
14 9213014 ROTOR 1 34 9213036 SCREW 2
15 9213015 ROTOR BLADE 5 35 9612848 O-RING 4
16 9213016 CYLINDER 1 36 9213040 VALVE BUSHING 1
17 9213017 REAR END PLATE 1 37 9OR0601 O-RING 1
18 9213018 PIN 1 38 9213042 REVERSE VALVE KNOB 1
19 9B626ZZ BALL BEARING 1 39 9621238 SPRING 1
20 9213020 GASKET 1 40 9STB3175 STEEL BALL 1
/
