AIRCAT 1300-TH-A User manual

Brand: AIRCAT

Model: 1300-TH-A

Type: User manual

AIRCAT 1300-TH-A is a powerful 3/8" impact wrench delivering 450 ft-lb of torque and 1750 impacts per minute. It features a durable hammer case and front end plate for increased longevity and a 2-5/8" length for hard-to-reach areas. With a free speed of 10,000 RPM, this impact wrench is ideal for automotive repairs, construction projects, and other heavy-duty tasks.

MODEL: 1300-TH-A

3/8" IMPACT WRENCH

SPECIFICATIONS

Important Warnings - Impacts

1. Eye protection and hearing protection and safety gloves must always be worn when operating an impact wrench or impact

driver.

2. When using heavy impact sockets or sockets on impact wrenches with 3/4” drive anvils or larger, a socket retaining ring

and pin should be used to prevent the socket falling off and causing injury.

3. Use only impact sockets and accessories. Only use sockets designated “FOR USE WITH IMPACT WRENCHES”, hand tool

damage and replace when necessary.

Accessory Hazards

4. Disconnect the assembly power tool for threaded fasteners from the energy supply before changing the inserted tool or

accessory.

5. Do not touch sockets or accessories during impacting as this increases the risk of cuts, burns or vibration injuries.

6. Use only sizes and types of accessories and consumables that are recommended by the assembly power tool for threaded

fasteners manufacturer; do not use other types or sizes of accessories and consumables.

Model No.

Free Speed

(RPM)

Bolt

Capacity

(in.)

Square

Drive

(in.)

Impacts Per

Minute

Max Torque

(ft-lb)

Weight

(lbs.)

Length

(in)

Air Cons.

(CFM)

Rec. Hose

Size

(in.)

Air Inlet

(in.)

1300-TH-A 10,000 1/2 3/8 1750 450

2-5/8 6-3/4 6 3/8 1/4 NPT

Air Supply

Tools of this class operate on a wide range of air pressure. It is recommended that air pressure of these tools measures 90 PSI at the tool while running free. Higher

pressure and unclean air will shorten the tool’s life because of faster wear and may create a hazardous condition and void the warranty. Water in the air line will

cause damage to the tool. Drain the air tank daily. Clean the air inlet lter screen on at least a weekly schedule. The recommended hookup procedure can be viewed

in the illustration below. The air inlet, used for connecting air supply, has standard 1/2” NPT American Thread. Line pressure should be increased to compensate for

unusually long air hoses (over 25 feet). Minimum hose diameter should be 1/2” I.D. and ttings should have the same inside dimension.

MODEL: 1300-TH-A

3/8" IMPACT WRENCH

Exploded View & Parts List

Ref

Part Number Description Qty Ref

Part Number Description Qty.

1 00-4603 Grease Fitting 1 21 243F-030 Rear Gasket 1

2 243J-SH-002D Hammer Case 1 22 243F-031 Washer 1

3 00-4302 Inserts Recoil 4 23 243F-019 Air Channel Gasket 1

4 242-010B Anvil Bushing 1 24 Motor Housing 1

5 243H-020 Front Gasket 1 25 243J-022 Regulator Knob 1

6 242-026 Anvil Collar 1 26 00-6203 Cap Screw 1

7 00-4144 O-Ring 1 27 243H-028 Screw 4

8 243L-011NA3 Anvil 1 28 243H-024 Trigger 1

9 243L-016 Hammer Pin 2 29 00-4101 O-Ring 1

10 243L-017B Hammer 2 30 00-3335 Spring Pin 1

11 243L-012 Hammer Cage 1 31 00-3308 Spring Pin 1

12 00-2306 Ball Bearing 1 32 306-027-B Bushing 1

13 243L-005 Front End Plate 1 33 306-026 Valve Stem 1

14 243L-007B Rotor 1 34 243H-023 Spring 1

15 243L-008D Rotor Blade 6 35 243H-021

16 243L-006 Cylinder 1 36 00-4126 O-Ring 1

243F-033-B Valve Sleeve Gasket 1 37 00-4143 O-Ring 1

243F-029 Valve Sleeve 1 38 00-4127 O-Ring 1

00-2326 Ball Bearing 1 39 305F-032 Washer 1

00-3328 Spring Pin 1 40 305F-025C-B Air Inlet (1/4” NPT) 1

40 305F-025C-B-1 Air Inlet (1/4” BSP) 1

243F-041 Square Ring 1

41 243H-019B Exhaust Tube 1

17 00-4158 O-Ring 1

42 243H-026 Felt 1

18 305F-034 Spring 1

43 243H-027 Non woven 1

19 00-3805 Steel Ball 1

44 00-3435 Pin 1

20 243J-021 Regulator 1

243L-001AI1300-A

SERVICE CENTER LISTINGS ENCLOSED

AIRCAT and NITROCAT air tools are warranted to be free from defects in material and workmanship for 2 years from date

of purchase. We will repair or replace; at our option any defective part or unit which proves to be defective in material or

workmanship during this 2 year period. The foregoing obligation is AIRCAT and Florida Pneumatic's sole liability under this

or any implied warranty, under no circumstances shall it be liable for any incidental or consequential damages.

This warranty applies to the tool only. The warranty does not apply to any attached accessories/consumable products;

such as drill chucks, sander backing pads, air hammer retainers and chisels or “kit” accessories or any other accessory

included with the tool.

an AIRCAT or Florida Pneumatic Authorized Service Center) are not covered by this warranty.

Return your tool to an AIRCAT or Florida Pneumatic Authorized Service Center freight prepaid. Be sure to include your

name, address, copy of purchase with date and description of the suspected defect.

AIRCAT whose policy is continued product improvement reserves the right to make changes in design or construction at

any time without incurring any obligation on tools previously sold.

Tune-Up and Head Kits for all AIRCAT PNEUMATIC impact wrenches and ratchets are available.

For Authorized Service Centers, please visit www.aircat.com/warranty-service

AIRCAT 1300-TH-A User manual

AIRCAT 1300-TH-A User manual

AIRCAT 1300-TH-A User manual

Related papers

Other documents