Vehicle Back-Up Camera & Monitor DVR Kit
PLCMTRDVR47
9’’ Display, Video Recording, Quad-View Ability,
Night Vision, Waterproof Cams (For Truck, Van, Bus, Trailer)
www.PyleUSA.com
2
Please read instructions carefully before installation and use.
Installation should be performed by a professional installer.
NOTICE
For your safety, please do not watch videos on the monitor when driving.
Except professional repair-men, do not modify the machine. lf the machine
doesn‘t work, please consult customer services or send the machine to local
maintenance departments.
WARNING:
Please install this machine in the place where laws and regulations allows it,
our company take no responsibility for illegal product installation.
ATTENTION:
The machine may appear darkscreen phenomenon when starting up in the
cold days, after power on and machine's temperature gradually rises up, the
display screen would gradually return to normal.
APPLICATION
This product adopts digital TFT color LCD of high denition real-time
monitoring, stored in SD card; built-in DVR recording function with one
single image or quad split images; supports 1way AV recording; built-in
speaker and with remote control. The installation is convenient and the
connection is simple.With no radiation, low comsumption, beautiful and
vivid image, small size etc features, widely applied in universal car security
and monitor.
BUTTON FUNCTION
www.PyleUSA.com
3
1. Labelling Mark
2. MENU: Compound key in the settings menu, four split & DVR mode.
3. CH 1: Direct channel CH 1 mode in split mode.
In four split state its the menu minus. Menu up in DVR state, its the last
page in the DVR video playback state is used to select videos.
4. CH 2: Direct channel CH 2 mode in split mode. Menu plus in four split
state. Drop down menu in DVR State. The next page in DVR video play
back state, used to select videos.
5. POWER: Monitor standby/switch ON
6. CH3: It is the direct channel 3 mode in split mode, it is the down in the
four split status menu, left in the DVR status menu, CH3 is the play button
in DVR video.
7. CH4: It is the direct channel 4 mode in split mode, UP in the four split
status menu, right in DVR status status menu, and in DVR videos CH4
indicates “pause”.
8. MODE: In four split screen, it is the cyclic switching of the mode 2 division,
-3 segmentation, -4 segmentation. In DVR state, MODE is used to switch
playback/video mode.
9. Remote Control window.
BUTTON FUNCTION
8
www.PyleUSA.com
4
1. Labelling Mark
2. POWER: Compound key long press indicates that the monitor is standby
/switched ON. Short press indicates four split/DVR screen switching
3. MODE: Compound key short press indicates the loop switch of the split
mode 2 - split 3 - split 4/ln the DVR state. MODE can switch to playback
/video mode. Long press represents the conversion of the four division
and the DVR mode
4. CH1: It is the direct channel CH1 mode in split mode/In the four split
state, it is menu minus/the menu up in the DVR state/ the last page in DVR
video playback state, used to select videos.
5. CH2: The direct channel CH2 mode in split mode/It is menu plus in the
four split state/It is the menu down in the DVR state/ It is the next page in
the DVR video playback state, used to select videos.
6. Ch3: The direct channel 3 mode in split mode/down in the four split
status menu/left in DVR status menu/in DVR video, CH3 is the play button
7. Ch4: Direct channel 4 mode in split mode/It is up in the four split status
menu/It is right in the DVR status menul In DVR videos. CH4 indicates
pauses
8. Remote Control Window
REMOTE CONTROL
POWER: Standby/boot button.
you can achieve standby mode or boot mode
DVR/AV: Toggle the DVR mode and the four
split mode
MODE1: In DVR mode. Used for loop
switching of video/playback
SETUP: In DVR mode. you can open the DVR
settings menu
UP: Up direction
MUTE: Mute switch. No power amplier. no
support
LEFT: Left direction
www.PyleUSA.com
5
REC/ENTER: In DVR mode, video start (stop) / conrm function
RIGHT: Right direction
MENU: Screen display settings menu
DOWN: Down direction
MODE: Four split compound split mode switching. Cyclic switching of 2
segmentation, 3 segmentation, 4 segmentation
CH1: In the four split mode, use to switch directly to single channel 1
VOL+: Volume increase. No power mode. No support
CH2: In the four split mode, use to switch directly to single channel 2
CH3: In the four split mode, use to switch directly to single channel 3
VOL-: Volume reduction. No power mode. No support
CH4: In the four split mode, use to switch directly to single channel 4
INSTRUCTION MANUAL
How to set DVR video time
In DVR mode, enter the DVR settings menu via remote control SETUP or
panel MENU, and then click it again to enter the SETUP Options box as
follows:
Press up and down to enter the INPUT item remote control. REC/ENTER to
enter date setting. Remote control 'REC/ENTER' or panel. press CH3 to enter
time setting. Change the time page up and down:
www.PyleUSA.com
6
How to operate DVR video
In DVR mode, remote control MODE1 or long press the keypad MODE to
switch to burn mode, while the lower left corner of the white time display as
shown
And then remote control REC / ENTER or monitor panel long press CH3
for recording mode. The image began to burn, the upper left corner of
the red dot will ash as shown:
www.PyleUSA.com
7
How to view DVR burn videos
In the DVR mode, remote control MODE1 or press the panel MODE to switch
to view the recording mode, the upper left corner ofthe display has a black
folder icon and the current video track display. You can press CH1/CH2 up
and down button to select dierent video le. In the lower left corner; OK,
play, pause icon and time displays, and then remote control REC / ENTER or
panel press CH3 to conrm the video playback:
CONNECTION
4 PIN
www.PyleUSA.com
8
MONITOR STANDARD INSTALLATION
1. Remove the screw around then take out the monitor. Put U type bracket
to the right place and adjust. Prepare 3 screws. (see below pictures)
2. Lock the bracket by screws. Put the monitor into the bracket. Adjust angle
and locking it. (see below pictures)
3. Finish the installation. The adjustable angle is forwad 30° and backward
30°. User can adjust its preferred angle. (see below pic.)
www.PyleUSA.com
9
Monitor lnstallation (Optional)
1. Firstly x the screws and fan-shaped bracket tight. (see below pictures)
2. Secondly put the metal buckle piece on the top of the fan-shaped bracket
into the notch at the back of the monitor. (see below pictures)
3. Move the bracket to the proper location. (see below pictures)
Tapping screw
or Machine screw
with nut.
www.PyleUSA.com
10
4. Fix the big screws of the bracket until to keep the monitor tight
(see below pictures)
5. To change the direction or angle of the monitor, rstly loosen the screws
on the bottom of the bracket. Then move the monitor to the desired
location then x the screws on the bottom of the bracket again.
(see below pictures)
PRODUCT MAINTENANCE
1. DO NOT install the products in a damp place
2. Do not squeeze or scratch the product with sharp objects.
3. Wipe the products with a soft cloth soaked with a small amount of mild
detergent. When cleaning the TV, do not use polishing cloths, disinfectants
or any kind of fuel or chemical cleaners such as alcohol and gasoline, etc.
4. Unplug or turn o the power if the unit is not in use.
Notice:
Please obey the local laws to install the product at a right position.
Our company is not responsible for the law issue caused by the illegal
installation
www.PyleUSA.com
11
ACCESSORY
www.PyleUSA.com
12
INSTALLATION EXAMPLES
Monitor system used in truck, bus, express car, or special vehicle
www.PyleUSA.com
13
PLCMTRDVR47
Vehicle Back-Up Camera & Monitor DVR Kit - 9’’ Display,
Video Recording, Quad-View Ability, Night Vision,
Waterproof Cams (For Truck, Van, Bus, Trailer)
Features:
• DVR Dash-Cam Bundle Kit
• Includes Monitor Display
+ Dual Cameras
• Video Recording & File Saving
via SD Memory Card Slot
• Easily Save & Share les
via Computer
• Ability to Connect Additional
/ External Cameras
• Quad-View Display Ability:
Choose to View 1, 2 or 4 Cameras
On-Screen
• Universal Mount:
For All Vehicle Types
• Night Vision Illumination
• Auto White Balance
& Image Adjustment
• Includes All Necessary Cables
& Wiring for Installation
• Used for Car, Truck, Bus, Van, Trailer,
Mobile Vehicle Applications
Technical Specs:
• Monitor Type:
LCD-TFT, 9.0’’ -inches
• Monitor Screen Resolution:
800 x 480 Pixels
• On-Screen Viewing Modes:
Single Camera, Dual Camera,
Quad 4-Way Camera
• Recording Speeds:
PAL 50 FPS, NTSC 60FPS
• Back Light: LED, 400cd/m2
• Video Output: NTSC / PAL
• Camera Marine Grade Rating: IP-69
• Viewing Angle: 170 Degree
• Video System: PAL/NTSC Auto Switching
• Image Sensor: 1/4’’ Color CMD
What’s in the Box:
• Display Monitor
• (2) Backup Cameras
• Remote Control
• Power & Wiring Harness
Backup Cameras:
• Universal Exterior Mount Design
• Waterproof & Weather-Resistant
• Marine Grade Camera Construction
• Rugged & Durable Metal Housing
• Tilt Adjustable Camera Lens Angle
• Resolution 580 x 540 Pixels
• Battery Operated Remote Control:
Requires (2) x ‘AA’ Batteries,
Not Included
• Maximum SD Card Support:
Up to 32GB
• Power Supply: 12-24V, DC
• Monitor Dimension (L x W x H):
7.08'' x 4.76'' x 1.02'' -inches
• Sold as: 1
/
