PAC HYNK1142 User manual

Type
User manual

This manual is also suitable for

PAC BKHYNK1142 is a dash kit for your vehicle that allows you to replace your factory radio with an aftermarket radio. It's designed to fit select Hyundai Elantra models from 2007-2010. The kit includes a mounting bracket, trim ring, and pocket to give your new radio a factory-installed look. With this kit, you can upgrade your sound system without sacrificing the aesthetics of your dash.

PAC BKHYNK1142 is a dash kit for your vehicle that allows you to replace your factory radio with an aftermarket radio. It's designed to fit select Hyundai Elantra models from 2007-2010. The kit includes a mounting bracket, trim ring, and pocket to give your new radio a factory-installed look. With this kit, you can upgrade your sound system without sacrificing the aesthetics of your dash.

CUSTOMER HELP LINE
USA 800-323-4329 Canada 800-245-8777
iHYNK1142
Automotive Products Division
1040 Avenida Acaso Camarillo, CA 93012, U.S.A.
USA Sales (800) 336-6500
Canada Sales (888) 922-3006 USA Fax (805) 388-7950
For information about other American International automotive
accessories visit our website at:
http://www.americaninternational.net
©2010 AMERICAN INTERNATIONAL INDUSTRIES, INC.
Ver. 7/10
HYN-K1142 Mounting Kit
Hyundai
2007-10 ELANTRA (radio delete vehicles only)
VEHICLE APPLICATIONS
1. Set the parking brake.
2. Using a panel removal tool, carefully unfasten and pull forward the trim bezel
from around the radio.
3. Pull the radio trim bezel forward, disconnect all attached harnesses and
remove radio trim bezel.
4. Remove the (4) Phillips screws securing the factory pocket and black out
plate/bracket assembly to the sub-dash.
5. Pull the pocket and bracket assembly forward, disconnect all attached harnesses
and antenna lead and remove pocket and bracket assembly.
DASH DISASSEMBLY INSTRUCTIONS
1 2
1. This kit is an (ISO) mounting kit only.
2. The mounting sleeve of your new audio/video components and trim ring cannot be
used when ISO mounting an aftermarket radio. Your audio/video components must
have a removeable trim ring.
3. It is advisable to assemble the kit and new radio or audio/video component(s) on a
work bench, or flat surface when assembling so you can get the radio component(s)
to be straight when tightening the mounting screws.
4. Start by loosely attaching the new radio component(s) between the mounting
brackets using the screws supplied with the kit or new radio.
5. Slide the audio/video component(s) forward or back for desired look and tighten
the screws on the side brackets.
6. Install and wire the assembled radio component in the dash and secure to
the sub-dash using the factory screws that were removed when removing
the factory radio.
7. You may need to move the new audio/video component(s) forward or back for a
better look, or to allow the face of the new component(s) to operate
without interference.
8. Attach a rear support bracket to the rear of the new radio and adjust as necessary
to support the weight of the radio.
KIT ASSEMBLY INSTRUCTIONS
1. This kit is an (ISO) mounting kit only.
2. The mounting sleeve of your new audio/video components and trim ring cannot be
used when ISO mounting an aftermarket radio. Your audio/video component must
have a removeable trim ring.
3. It is advisable to assemble the kit and new radio or audio/video component on a
work bench, or flat surface when assembling so you can get the radio component(s)
to be straight when tightening the mounting screws.
4. Start by loosely attaching the new radio component between the mounting
brackets using the screws supplied with the kit or new radio.
5. FOR SINGLE ISO INSTALLATION ONLY:
Insert the pocket under the radio and lock into the slots provided on the
mounting brackets. See Fig. A on page 2.
6. Slide the audio/video component forward or back for desired look and tighten the
screws on the side brackets.
7. Install and wire the assembled radio component in the dash and secure to
the sub-dash using the factory screws that were removed when removing
the factory radio.
8. You may need to move the new audio/video component forward or back for a better
look, or to allow the face of the new component to operate without interference.
9. Attach a rear support bracket to the rear of the new radio and adjust as necessary
to support the weight of the radio.
Single ISO Mount Applications
Double ISO Mount Applications / Double DIN Mount Applications
Fig A
IMB-1142 L
IMB-1142 R
POC-568
TRIM RING-HYN-K1142
Pocket Slots
  • Page 1 1
  • Page 2 2

PAC HYNK1142 User manual

Type
User manual
This manual is also suitable for

PAC BKHYNK1142 is a dash kit for your vehicle that allows you to replace your factory radio with an aftermarket radio. It's designed to fit select Hyundai Elantra models from 2007-2010. The kit includes a mounting bracket, trim ring, and pocket to give your new radio a factory-installed look. With this kit, you can upgrade your sound system without sacrificing the aesthetics of your dash.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI