the great outdoors by Minka Lavery 73063-246 Operating instructions

Brand
the great outdoors by Minka Lavery
Model
73063-246
Type
Operating instructions

This manual is also suitable for

INSTALLATION INSTRUCTIONS
For Model 73061-246 (Rev. 02/21/2014)
READ AND SAVE THESE INSTRUCTIONS
W A R N I N G ! S H U T P O W E R O F F AT F U S E O R C I R C U I T B R E A K E R .
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
Fig.1
PREPARING FOR INSTALLATION (Fig. 1)
1. Shut off the power at the fuse box or circuit breaker. If
necessary, remove the old fixture, including the
mounting hardware.
2. Carefully unpack your new fixture, lay out all parts on a
clear area. Take care not to lose any small parts
necessary for installation.
3. Attach the circular strap (A) to the outlet box using the
mounting screws (B) (Size: #8-32N*L0.5”). The side of
the circular strap (A) marked “GND” must face out.
4. Install 2 studs (C) into the circular strap (A), spaced the
same distance apart as the holes in back plate (D).
5. Install 1*40W ST58 bulb (included) in accordance with
the fixture’s specification. (DO NOT EXCEED THE
MAXIMUM WATTAGE RATING!) (NE PAS DEPASSER
LA PUISSANCE NOMINALE MAXIMALE!).
6. Align glass shade (H) to top cover (J).
7. While supporting the glass shade (H), align metal ring (I)
onto the bottom of glass shade (H). Secure brackets (F)
to top cover (J) and metal ring (I), with cap nuts (G) to
secure the glass into place.
CONNECTING THE WIRES (Fig. 2)
8. At this point, connect the fixture wires to outlet box wires
as shown in Fig. 2, making sure that all wire connectors
are secured and do not pull off with a slight tug. If your
outlet box has a ground wire (green or bare copper),
connect the fixture’s ground wire to it. Otherwise,
connect the fixture’s ground wire directly to the circular
strap (A) using the green screw provided.
COMPLETING THE INSTALLATION (Fig. 1)
9. Align back plate (D) onto studs (C) and secure with ball
nuts (E).
10. To prevent moisture from entering the outlet box and
causing a shortage, use clear caulking (i.e.
Indoor/Outdoor silicone sealant) to outline the outside
of fixture backplate where it meets the wall leaving a
space at the bottom to allow moisture a means to
escape (Fig.3).
Your installation is now complete. Return power to the
outlet box and test the fixture.
Note: Illustration (Fig. 1) on this manual is for
installation purposes only. It may or may not be
identical to the fixture purchased.
LA-2391E
Fig.2
FIXTURE
WIRES
Black or
Smooth
HOUSE
WIRES
Black
(Hot)
FIXTURE
WIRES
White or
Ribbed
HOUSE
WIRES
White
(Neutral)
FIXTURE
WIRES
Bare
Copper
(Ground)
H
OUSE
WIRES
Green or
Bare
Copper(Gr
ound)
Set
A
-
020
- Circular Strap
- Ground Screw
- Mounting Screw*2
A
B
C
D
E
F
I
G
H
G
J
Fig.3
CAULKING
Backplate
  • Page 1 1

the great outdoors by Minka Lavery 73063-246 Operating instructions

Brand
the great outdoors by Minka Lavery
Model
73063-246
Type
Operating instructions
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents